The working condition of a centrifugal pump as a turbine (PAT) is often unsteady. The rotating speed of a PAT constantly varies as the flow and load change, resulting in transient hydrodynamic behaviors between different working conditions. During the transition, the PAT undergoes a severe change in performance and complicated internal flow structures. In previous work, the fixed rotating speed of a PAT was mostly considered using computational fluid dynamics. To investigate the transient behavior of a PAT, relevant simulation tools are developed to depict transient flow conditions, and the corresponding transient speed of the impeller is calculated. Both large and small fluctuation transitions are simulated for the practical application of the PAT. The simulated results are first verified by experiments. The results show that the rotating speed significantly affects the performance and stability of the PAT. The rapid increment in flow rate and rotating speed lead to large energy dissi... [more]

This review paper examines the applicability of biogas and biomethane as potential maritime fuels and examines issues of these fuels from a supply chain perspective (from production to end use). The objectives are to identify: (1) the latest research, development, and innovation activities; (2) issues and key barriers related to the technology readiness to bring biogas/biomethane to market; and (3) commercialisation issues, including cost parity with natural gas (the main competitor). A survey of the literature was carried out based on research articles and grey literature. The PESTEL and SWOT analyses identified opportunities for these fuels due to the relevant regulations (e.g., Fit for 55; the recent inclusion of the Mediterranean Sea as a SECA and PM control area; MPEC 79), market-based measures, and environmental, social, and governance strategies. The potential of biomass feedstock is estimated to have a substantial value that can satisfy the energy needs of the maritime industry... [more]

Biogas is drawing attention as it can be a solution both to increase the renewable energy for heat or power supply and to help achieve a decarbonized economy. In this work, the measurements of the speed of sound of three mixtures of biogas from the biomethanation plant of the municipal waste of Valdemingómez, Madrid (Spain), are presented. The measurements were performed using an acoustic resonator, which is able to measure the speed of sound of gas mixtures with a relative expanded uncertainty of approximately 0.08%. A virial-type equation was also applied to fit the experimental values of the speed of sound, and the heat capacities as perfect gas were derived with uncertainties below 0.8%. In addition, the experimental results were compared with those calculated with the reference equations of state for natural gas mixtures such as GERG-2008 and AGA8-DC92. For both equations, the average relative deviations were less than 0.02% and 0.2% for the speed of sound and the heat capacities,... [more]

Design priorities for tall and supertall buildings have for some time shifted to achieving more energy efficiency to address the energy needs of the increasing global population. Engineers and architects aim to achieve energy conservation through active and passive approaches, pursuing technological innovations and adopting climate-responsive design. Because of the green movement currently dominating the building industry, tall buildings that need a massive amount of energy to build and operate, and the practical desire to switch from non-renewable to clean renewable energy resources, intense attention has been given to the energy efficiency of tall buildings in the recent past. Due to the vast array of energy-efficient design features, equipment, and applications available now, it is timely to examine the pros and cons of these issues. This review paper is an attempt to comprehensively present and deliberate these issues. It illustrates and discusses the concepts and applications thro... [more]

In this paper, a new R744 heat pump system is studied. The gas cooler, evaporator, indoor heat core, and indoor gas cooler are all micro-channel heat exchangers. The R744 high pressure system adopts a combination of an accumulator and internal heat exchanger (ACCU/IHX). In addition, an electronic reversible regulating valve is added before the outdoor gas cooler, making the outdoor heat exchanger able to be used as a gas cooler or evaporator. The water-cooled condenser can improve the performance in the cooling or heating mode. The research contents contain the performance and optimal pressure under extreme conditions as a result of the experiments. The results show that the cooling capacity can reach 8.2 kW with a COP of 1.87, under a 40 °C external circulation intake. The cooling capacity on the battery side can reach 11 kW under an ambient temperature of 40 °C, which can provide a sufficient cooling capacity. Under an ambient temperature of −20 °C, the maximum heating capacity can r... [more]

Nowadays, the imperative need for the reduction of Greenhouse Gas (GHG) emissions leads to the wider adoption of environmentally friendly transportation means. As a result, various policies underpinning the Electric Vehicle (EV) deployment are legislated globally, and several technical advances contributing to the electrification of the transportation sector are pursued. In this paper, a comprehensive overview of the current status of the infrastructure utilized for the realization of both conductive and contactless (wireless) charging of an EV battery is conducted. Furthermore, the issue of EV integration in conventional distribution networks, as well as in future power system architectures, is discussed in detail. Particular focus is given to wireless (i.e., inductive) charging. A detailed presentation of the respective standards and charging levels, as well as the magnetic couplers and the compensation network configurations, is carried out. Moreover, innovative concepts such as dyn... [more]

The dynamic development of electromobility has resulted in new directions of research, one of which is the analysis of the noise of traction motors. The designs of the motors used in electric vehicles are relatively new and often modified. In addition, strong competition also forces an increase in the power generated per unit mass of the motor, often at the expense of weakening the mechanical structure. This may result in an increase in the noise level generated by the electric drive, so this issue should be analyzed at the motor design stage. Different construction and operating conditions in relation to industrial or railway traction motors make it necessary to constantly develop methods for the noise analysis of the motors for electric vehicles. The aim of this article is to review the methods used so far in an analysis of the noise generated by the motors for electric vehicles. Three main methods are used by the authors of this paper: the analytical method, the hybrid method using... [more]

The annual yield of bifacial photovoltaic systems is highly dependent on the albedo of the underlying soil. There are currently no published data about the albedo of red soil in western Africa. In this study, the impact of the albedo of red soil in Ghana on the energy yield of bifacial photovoltaic systems is analysed. A bifacial photovoltaic simulation model is created by combining the optical view factor matrix with an electrical output simulation. For an exact simulation, the albedo of red soil at three different locations in Ghana is measured for the first time. The average albedo of every red soil is clearly determined, as well as the measurement span including instrumentation uncertainty; values between 0.175 and 0.335 were measured. Considering these data, a state-of-the-art bifacial photovoltaic system with an average of 19.8% efficient modules in northern Ghana can achieve an annual energy yield of 508.8 kWh/m2 and a bifacial gain of up to 18.3% in comparison with monofacial p... [more]

In this paper, we propose a sophisticated battery model for vanadium redox flow batteries (VRFBs), which are a promising energy storage technology due to their design flexibility, low manufacturing costs on a large scale, indefinite lifetime, and recyclable electrolytes. Primarily, fluid distribution is analysed using computational fluid dynamics (CFD) considering only half-cells. Based on the analysis results, a novel model is developed in the MATLAB Simulink environment which is capable of identifying both the steady-state and dynamic characteristics of VRFBs. Unlike the majority of published studies, the inherent characteristics of the flow battery, such as shunt current, ion diffusion, and pumping energy consumption, are considered. Furthermore, simplified charge transfer resistance (CTR) is taken into account based on electrochemical impedance spectroscopy (EIS) measurement results. The accuracy of the model was determined by comparing the simulation results generated by the equiv... [more]

The management of energy in distribution networks has been gathering attention in recent years. The simultaneous control of generation and demand is crucial for achieving energy savings and can further lower energy pricing. The work aims to develop a control scheme for a hybrid microgrid that can provide stability to the bus voltage and effectively manage the power flow. Solar energy is the current trend in renewable energy sources (RES). There is a surge in the installation of solar PV systems both on a large scale and on a small scale, such as rooftop PV systems. Installation of RES at residential premises has to be conducted with a proper power management scheme. The hybrid microgrid for this work consists of a PV system with a boost converter to extract maximum power, a DC-DC bi-directional converter to charge or discharge the hybrid energy-storing devices, and a three-phase AC-DC interlinking converter for exchange of energy with the utility grid. The control and power management... [more]

This study analyzes European natural gas (NG) prices since the eve of the 2008 financial crisis. Spearman’s rank correlation coefficients associate prices with and without taxation, whereas a hierarchical clustering analysis clarifies similarities in NG pricing behavior. After performing econometric tests to ensure the satisfaction of classical hypotheses and identify a system of endogenous variables, structured unrestricted and restricted vector autoregressive models are applied to panel data composed of 34 spatial units and 31 units of time drawn from 2007−2022 to confirm the presence of short-term and long-term causal dependencies. The nonparametric analysis identifies three groups of countries that exhibit a differentiated pricing behavior. The parametric analysis reveals a significant and asymmetric short run relation, which is imposed by liquefied natural gas (LNG) imports from Nigeria on the logarithm of NG prices. However, the sign of coefficients associated with lagged LNG imp... [more]

BECCS (bioenergy with carbon capture and storage) is an important technology to achieve international and Brazilian climatic goals, notably because it provides negative emissions. In addition, Brazil presents favorable conditions for the development of BECCS, given the country’s mature biofuel industry. Therefore, this research aims to provide a systematic literature review of the effective potential of and barriers to implementing bioenergy with carbon capture and storage in Brazil. The platforms chosen for this study are Science Direct and Integrated Search Portal, which is a search portal administered by the University of São Paulo. The search initially identified 667 articles, of which 24 were analyzed after selection and screening. The results show that technical factors are not a current barrier to the implementation of BECCS in Brazil, especially in ethanol production. However, the economic results vary among articles, but no BECCS plant has been shown to be economically feasibl... [more]

Solar cell equivalent circuit modelling is usually based on continuous I-V models, with a set of data obtained by analytical expressions. This work proposes an almost discrete novel mathematical method and correspondent electrical model, based on the I-V curve adjustment at every two adjacent points. It is based on the discretisation of any diode model behaviour, such as the 1M5P (also known as 1D5P) or the 1M7P (also known as 2D7P). For this reason, the model is named d1MxP, meaning that it is a discrete (d) model (1M) with x parameters (xP). The modelling methodology validation process uses experimental data already published in the literature. According to the presented results, the proposed method shows increased accuracy when compared to the 1M5P or 1M7P equivalent models. The accuracy on the maximum power point and fill factor determination is relevant, resulting in an improvement of up to 3.34% in the maximum power, up to 5.70% in its voltage and up to 8.20% in its current, for... [more]

Gas reservoir numerical simulation is an important method to optimize the development strategy of shale gas reservoirs which has been influenced by the multi-stage fracture. The regular fracture network model was used to build a conventional numerical simulation, in which it was difficult to show the true situation of fracture propagation. However, the physical parameters not only affect the production, but also influence the stimulation effect; moreover, the quality of the fracturing effect also affects the production which causes the input and out parameters to be inaccurate. To solve this problem, the process simulation must be completed from geology to engineering to gas reservoir. The main controlling factors of production are identified with geological and engineering factors such as horizontal stage length, the volume of fracturing fluid, well spacing, production allocation, and proppant mass. Therefore, on the basis of the integrated simulation method of a hydraulic fracturing... [more]

A two-trough parabolic-shaped concentrating photovoltaic solar collector with a vertical half-size ‘phosphorus-passivated emitter rear totally diffused’ bifacial cell string receiver was designed and built for household applications, with the aim of smooth the electrical ‘duck curve’. The study consisted in testing the concentrating photovoltaic solar collector outdoors, under real weather conditions, for its daily electrical peak power and efficiency, as well as for its electrical transversal and longitudinal Incidence Angle Modifier direction. The outdoor testing measurements were conducted in a parabolic trough with low concentration coupled with a central vertical half-size ‘phosphorus-passivated emitter rear totally diffused’ bifacial cell string receiver. Furthermore, the electrical transversal Incidence Angle Modifier showed to be very delicate due to the position and outline of the receiver, which led to an electrical peak efficiency close to 10% at ±25° (i.e., for an electrica... [more]

In this study, a power control algorithm of a variable-speed fixed-pitch horizontal-axis lift-type 20 kW small wind turbine (SWT) was proposed and verified through dynamic simulations. The power control algorithm proposed in this study consists of algorithms for Region II to track the maximum power coefficient, for Region II-1/2 to maintain the rated rotor speed, and for Region III to maintain the rated power. To verify the proposed power control algorithm, simulations were performed at the rated wind speed and above the rated wind speed, to which turbulence intensity based on the IEC regulation’s normal turbulence model was applied. As a result, it was confirmed that the proposed controller operates properly in the whole three regions including Regions II, II-1/2, and III. The controller performance was then compared with the variable-speed variable-pitch power controller. Although the performance of the proposed controller was considered good for the target VSVP wind turbine, it was... [more]

The challenges related to climate policy and the energy crisis caused the search for alternative ways of obtaining energy, one of the essential tasks faced by scientists and political decision-makers. Recently, much attention has been paid to biomethane, which is perceived as a substitute for natural gas. Compared to the traditional combustion of biogas in cogeneration units (CHP), upgrading it to the form of biomethane can bring both environmental benefits (reduction in GHG emissions) and economic benefits (higher efficiency of energy use contained in biomass). The purpose of this review was a comprehensive assessment of the conditions and opportunities for developing the biomethane sector in the EU in the face of challenges generated by the energy and climate crisis. The article reviews the condition of the biomethane market in the European Union, focusing on such issues as biomethane production technologies, current and future supply and demand for biomethane, and biomethane product... [more]

Decarbonization of existing electricity generation portfolios with large-scale renewable resources, such as wind and solar photo-voltaic (PV) facilities, is important for a transition to a sustainable energy future. This paper proposes an ultra-fast optimization method for economic dispatch of firm thermal generation using high granularity, one minute resolution load, wind, and solar PV data to more accurately capture the effects of variable renewable energy (VRE). Load-generation imbalance and operational cost are minimized in a multi-objective clustered economic dispatch problem with various generation portfolios, realistic generator flexibility, and increasing levels of VRE integration. The economic feasibility of thermal dispatch scenarios is evaluated through a proposed method of levelized cost of energy (LCOE) for clustered generation portfolios. Effective renewable economics is applied to assess resource adequacy, annual carbon emissions, renewable capacity factor, over generati... [more]

This paper studies the distribution of emergency relief for electric vehicles (EVs), which considers energy saving, multi-depot, and vehicle routing problems with time windows, and the named energy saving-oriented multi-depot vehicle routing problem with time windows (ESMDVRPTW). Our aim is to find routes for EVs such that all the shelter demands are fulfilled during their time windows and the total cost traveled by the fleet is minimized. To this end, we formulate the ESMDVRPTW as a mixed-integer linear programming model. Since the post-disaster transportation network contains a large number of vertices and arcs composed of vertices, we propose a two-stage approach to solve the ESMDVRPTW. The first stage is to obtain the minimal travel cost between any two vertices in real-time on a post-disaster transportation network using the proposed Floyd algorithm combined with the neighboring list (Floyd-NL algorithm). In the second stage, we develop the genetic algorithm (GA) incorporating lar... [more]

Bio-SRF based on livestock waste has low heating value and high moisture content. The concentration of toxic gases such as SOx, NOx, and HCl in the flue gas is changed according to the composition of fuel, and it has been reported. Therefore, the study of fuel combustion characteristics is necessary. In this study, we investigated combustion characteristics on the blended firing of coal and Bio-SRF (bio-solid refused fuel) made from livestock waste fuel in CFBC (circulating fluidized bed combustor). The raw materials for manufacturing Bio-SRF include agricultural waste, herbaceous plants, waste wood, and vegetable residues. Bio-SRF, which is formed from organic sludge, has a low heating value and a high moisture content. Bio-SRF of livestock waste fuel is blended with different ratios of coal based on heating values when coal is completely combusted in CFBC. In the result of experiment, the combustor efficiency of calculated unburned carbon concentration in the fly ash shows 98.87%, 99... [more]

This paper presents the potentials and costs of synthetic fuels (synfuels) produced by renewable energy via PEM water electrolysis and the subsequent Fischer−Tropsch process for the years 2020, 2030, 2040, and 2050 in selected countries across the globe. The renewable energy potential was determined by the open-source tool pyGRETA and includes photovoltaic, onshore wind, and biomass. Carbon dioxide is obtained from biomass and the atmosphere by direct air capture. The potentials and costs were determined by aggregating minimal cost energy systems for each location on a state level. Each linear energy system was modelled and optimised by the optimisation framework urbs. The analysis focused on decentralised and off-grid synthetic fuels’ production. The transportation costs were roughly estimated based on the distance to the nearest maritime port for export. The distribution infrastructure was not considered since the already-existing infrastructure for fossil fuels can be easily adopted... [more]

Different from common cylindrical magnetic bearings, the spherical radial AC HMB has obvious advantages in suppressing the gyroscopic effect, thus it is very suitable for application in flywheel battery systems. In this study, a precise mathematical model of suspension forces is deduced adopting wide-area and universal modeling theories in detail for the spherical radial AC HMB. Different from the traditional Maxwell tensor method based on a cylindrical two-dimensional coordinate system, the improved Maxwell tensor method based on a spherical coordinate system has a wider range and versatility. Then, the detailed explanation about the accuracy, wide-area and universality are given. Further, based on the model, the control system is designed, which includes the overall schematic, hardware and software designs. Finally, stiffness and performance tests are conducted. The good results of the stiffness tests indicate the error between the proposed model and the force-deflection stiffness te... [more]

With the increasing integration of wind and photovoltaic power, the security and stability of the power system operations are greatly influenced by the intermittency and fluctuation of these renewable sources of energy generation. The accurate and reliable short-term forecasting of renewable energy generation can effectively reduce the impacts of uncertainty on the power system. In this paper, we propose an adaptive, data-driven stacking ensemble learning framework for the short-term output power forecasting of renewable energy. Five base-models are adaptively selected via the determination coefficient (R2) indices from twelve candidate models. Then, cross-validation is used to increase the data diversity, and Bayesian optimization is used to tune hyperparameters. Finally, base modes with different weights determined by minimizing the cross-validation error are ensembled using a linear model. Four datasets in different seasons from wind farms and photovoltaic power stations are used to... [more]

Biosolids have been traditionally used as a beneficial resource in the agricultural industry. However, contaminants of emerging concern (CECs) threaten their reuse due to concerns of toxicity, bioaccumulation, and increased regulations on acceptable CEC concentrations in biosolids. The thermal treatment of biosolids has the potential to destroy/mineralize these contaminants as well as transform the biosolids into valuable biochar. However, the thermal processing of biosolids is highly energy intensive due to the energy costs associated with drying biosolids to the required moisture content for thermal processing. This article performs a brief review of the drying of biosolids from a physical and theoretical viewpoint. It also provides an overview of pyrolysis and gasification. It explains the impact that moisture can have on both the degradation of CECs and the products that can be obtained through the thermal treatment of biosolids. Additionally, model-based, lab-based, and pilot-scal... [more]

Big cities affected by intense mobility, traffic and pollution are adopting electrification-based solutions for the reduction of the CO2 emissions of combustion engines. An interesting field in which the transition toward electrification can achieve important benefits is the area of instant deliveries. Instant deliveries deal with the mobility related to commercial trades between suppliers and customers. In this respect, optimal solutions can be considered during route planning based on the minimization of several metrics, such as distance, energy and road slope, among others. To this end, this paper presents an optimal solution to the instant deliveries problem in which the result is the optimal route, in the city under study, that minimizes energy consumption based on road slope and total distance traveled, and that gives higher priority to routes that include cycling infrastructure that the city can provide. The paper uses electric bikes since they are easily transportable and are h... [more]