The aim of the present work is to investigate the possibility of producing activated carbons from the residual lignin stream of lignocellulosic ethanol biorefineries, as this represents an optimal opportunity to exploit a residual and renewable material in the perspective of sustainable bioeconomy, increasing biorefinery incomes by producing value-added bioproducts in conjunction with biofuels. Activated carbons (ACs) were produced via chemical (KOH) and physical (CO2) activation. Char samples were obtained by slow pyrolysis (SP) and hydrothermal carbonization (HTC). Several HTC experiments were carried out by varying residence time (0.5−3 h) and reaction temperature (200−270 °C), in order to evaluate their influence on the product yield and on the morphological characteristics of the hydrochar (specific surface area, total pore volume and pore size distribution). ACs from hydrochars were compared with those obtained from pyrochar (via physical activation) and from the raw lignin-rich... [more]

Understanding the pore structure can help us acquire a deep insight into the fluid transport properties and storage capacity of tight sandstone reservoirs. In this work, a series of methods, including X-ray diffraction (XRD) analysis, casting thin sections, scanning electron microscope (SEM), nuclear magnetic resonance (NMR) experiment and multifractal theory were employed to investigate the pore structure and multifractal characteristics of tight sandstones from the Taiyuan Formation in the southern North China Basin. The relationships between petrophysical properties, pore structure, mineral compositions and NMR multifractal parameters were also discussed. Results show that the tight sandstones are characterized by complex and heterogenous pore structure, with apparent multifractal features. The main pore types include clay-dominated micropores and inter- and intragranular dissolution pores. Multifractal parameters of sandstone samples were acquired by NMR and applied to quantitative... [more]

How to detect uric acid is an important issue. For the purpose of preparing a potentiometric uric acid biosensor, this research used nickel oxide (NiO) as the sensing film to deposit it onto the substrate by radio frequency sputtering, then modified it with reduced graphene oxide (rGO) and silver (Ag) nanowires. Reduced graphene oxide (rGO) not only has excellent electrical conductivity, but also can make the surface of the film have a larger surface area, while AgNWs have also been proven to improve catalytic activity; hence, these two materials were chosen as sensor modifiers. Finally, the stability and the various characteristics of the uric acid biosensor were investigated using a voltage−time (V−T) system. The results showed that the AgNW−uricase/rGO/NiO uric acid biosensor has average sensitivity with 4.66 mV/(mg/L). In addition, the sensor has good stability.

The raw materials sector plays a key role in the Polish economy. The mineral raw material industry encompasses many different, sometimes highly specialized activities, such as exploration, mining, hauling, mineral processing, metallurgy and metal refining, as well as risk assessment, management (environmental, financial, legal) and marketing. The purpose of the article is to identify the market gap for business for entities or individuals in the mineral resources sector in Poland. Taking into account the European Union regulations which enforce the closure of hard coal mines in Poland by 2050, it is reasonable to identify such a gap in the raw materials area, especially since the current situation may turn out to be a new revival of the raw materials market after the pandemic period. Based on the NACE classification, a key area was identified, which is dedicated to potential entrepreneurs in the mineral resources area. Based on an internal analysis, the sectors directly related to the... [more]

Agricultural waste, particularly lignocellulose, has been used in the second generation of biogas. Coffee pulp and chicken feathers can be developed as biogas raw materials because of their suitability as a biogas substrate. This study investigates the effect of the percentage of total solids (TS), carbon to nitrogen ratio (C/N, g/g), and delignification pretreatment on biogas production from coffee pulp and chicken feathers, and aims to compose kinetics using the modified Gompertz model. The results show that adjusting the percentage of TS at low-level speeds up the degradation process, which increases chemical oxygen demand (COD) reduction and biogas production. COD reduction and biogas production increase optimally at the 25 (g/g) C/N ratio. Pretreatment delignification aids microorganisms in substrate decomposition, resulting in faster COD reduction and biogas conversion. The 25% TS and 25 (g/g) C/N ratio with the delignification process achieved the best biogas production, with bi... [more]

Aiming at the problem of end structure heating caused by the excessive eddy current loss of large synchronous condensers used in ultra-high voltage (UHV) power transmission, combined with the actual operation characteristics of the synchronous condenser, a three-dimensional transient electromagnetic field physical model is established, and three schemes for adjusting the end structure of the condenser under rated condition are researched. The original structure has a copper shield and a steel clamping plate. Scheme 1 has no copper shield but has a steel clamping plate. Scheme 2 has no copper shield but has an aluminum clamping plate. By constructing a three-dimensional fluid−solid coupling heat transfer model in the end of the synchronous condenser, and giving the basic assumptions and boundary conditions, the eddy current loss of the structure calculated by the three schemes is applied to the end region of the synchronous condenser as the heat source, and the velocity distribution of... [more]

The potential-induced degradation (PID) mechanism in Cu(In,Ga)(Se,S)2 (CIGS) thin-film solar cells, which are alternative energy sources with a high efficiency (>23%) and upscaling possibilities, remains unclear. Therefore, the cause of PID in CIGS solar cells was investigated in this study at the cell level. First, an appropriate PID experiment structure at the cell level was determined. Subsequently, PID and recovery tests were conducted to confirm the PID phenomenon. Light current−voltage (I−V), dark I−V, and external quantum efficiency (EQE) analyses were conducted to determine changes in the cell characteristics. In addition, capacitance−voltage (C−V) measurements were carried out to determine the doping concentration and width of the space charge region (SCR). Based on the results, the causes of PID and recovery of CIGS solar cells were explored, and it was found that PID occurs due to changes in the bulk doping concentration and built-in potential at the junction. Furthermore, b... [more]

Graphene with fascinating properties has been deemed as an excellent reinforcement for cementitious composites, enabling construction materials to be smarter, stronger, and more durable. However, some challenges such as dispersion issues and high costs, hinder the direct incorporation of graphene-based reinforcement fillers into cementitious composites for industrial production. The combination of graphene with conventional fibers to reinforce cement hence appears as a more promising pathway especially towards the commercialization of graphene for cementitious materials. In this review paper, a critical and synthetical overview on recent research findings of the implementation of graphene in fiber-reinforced cementitious composites was conducted. The preparation and characterization methods of hybrid graphene-fiber fillers are first introduced. Mechanical reinforcing mechanisms are subsequently summarized, highlighting the main contribution of nucleation effect, filling effect, interfa... [more]

The slopes of open-pit mines are often at risk of failure. To identify this hazard, stability analyses are performed. An important element of these stability analyses is the reliable selection of input parameter values for the calculations. This selection is difficult because the slopes of the open pit are disturbed by mining activities. In such conditions, rheological processes, intensified by weathering, develop in open-pit slopes. This study is aimed at setting the strength parameters for the stability analysis of open-pit slopes with a developed slide process, using the random set method. The study was performed on the example of the open pit of the Bełchatów lignite mine, central Poland. A four-stage methodology, according to the random set method, was proposed. The methodology covered the following: site investigation, sensitivity analyses, shear strength reduction (SSR) analyses using numerical calculations, and probability analyses of the factor of safety (FoS) calculation resu... [more]

The present study is focused on the development of a material model where the orthotropic-visco-elastic and orthotropic-visco-plastic mechanical behavior of a polymeric material is considered. The increasing need to reduce the climate-damaging exhaust gases in the automotive industry leads to an increasing usage of electric powered drive systems using Lithium-ion (Li-ion) batteries. For the safety and crashworthiness investigations, a deeper understanding of the mechanical behavior under high and dynamic loads is needed. In order to prevent internal short circuits and thermal runaways within a Li-ion battery, the separator plays a crucial role. Based on results of material tests, a novel material model for finite element analysis (FEA) is developed using the explicit solver Altair Radioss. Based on this model, the visco-elastic-orthotropic, as well as the visco-plastic-orthotropic, behavior until failure can be modeled. Finally, a FE simulation model of the separator material is perfor... [more]

Pore network modeling based on digital rock is employed to evaluate the mobility of shale oil in Qingshankou Formation, Songliao Basin, China. Computerized tomography technology is adopted in this work to reconstruct the digital rock of shale core. The pore network model is generated based on the computerized tomography data. We simulate the dynamics of fluid flow in a pore network model to evaluate the mobility of fluid in shale formation. The results show that the relative permeability of oil phase increases slowly in the initial stage of the displacement process, which is mainly caused by the poor continuity of the oil phase. In the later stages, with the increase in the oil phase continuity, the range of relative permeability increases. With the increase of organic matter content, the permeability of the water phase remains unchanged at low water saturation, but gradually increases at high water saturation. At the same time, it can be seen that, with the increase in organic matter... [more]

In this work, the biomass productivity for biorefinery products and growth curves of three autochthonous microalgae collected in different reservoirs (“Scenedesmus sp.” (SSP), mixture of Scenedesmus sp., Chlorella minutissima, Chlorellas sp. and Nannochloropsis sp. named “La Orden” (LO) consortium and Chlorella minutissima named “Charca Brovales” (CB) consortium) were studied in a 5.5 L column laboratory photobioreactor. Two different culture media, Arnon culture (AM) and an agriculture fertilizer-based liquid medium (FM), have been used to evaluate the growth effect of the microalgae; it was found that the medium has a clear effect on the biomass productivity and growth rate, which ranged between 0.26−0.498 g L−1 d−1 and 0.288−0.864 d−1, respectively. In general, the elemental analysis and higher heating value of microalgae biomass for the three species were independent of the culture medium used for its growth, while their lipids and sugars content depended upon the species type... [more]

The article presents studies of plain concretes prepared based on a quaternary binder containing various percentages of selected supplementary cementitious materials (SCMs). The possibilities of nanotechnology in concrete technology were also used. An additional important environmental goal of the proposed solution was to create the possibility of reducing CO2 emissions and the carbon footprint generated during the production of ordinary Portland cement (OPC). As the main substitute for the OPC, siliceous fly ash (FA) was used. Moreover, silica fume (SF) and nanosilica (nS) were also used. During examinations, the main mechanical properties of composites, i.e., compressive strength (fcm) and splitting tensile strength (fctm), were assessed. The microstructure of these materials was also analyzed using a scanning electron microscope (SEM). In addition to the experimental research, simulations of the possible reduction of CO2 emissions to the atmosphere, as a result of the proposed solut... [more]

Coconut shells, low-cost and renewable agro-wastes, were used as a starting material in the synthesis of hierarchical activated carbons via hydrothermal, KOH-activation, and carbonization techniques. The ratio of KOH to hydrochar was varied in a systemic manner to study how it influences the texture and electrochemical behavior of the capacitor. Coconut shell-based carbon coated on nickel foams presented a surface area of 1567 m2 g−1, with micropores as well as mesopores widely distributed. The sample showed superior electrochemical performance, attaining 449 F g−1 at 1 A g−1 in 6 M LiNO3 aqueous solution. The solid-state symmetric supercapacitor device delivered a specific capacitance of 88 F g−1 at 1 A g−1 and a high energy density of 48.9 Whkg−1 at a power density of 1 kW kg−1. At a wide voltage window of 2.0 V, the sample was highly stable during the cycle test, showing a 92% capacitance retention at 2 A g−1 after cycling for 5000 times. The superior performance is due to the sampl... [more]

Silicon nanowire (SiNW) metal-oxide-semiconductor (MOS) capacitors with Al2O3/TiO2/Al2O3 (ATA) stacked dielectric films were fabricated by metal-assisted chemical etching (MACE) and atomic layer deposition (ALD). High-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) images revealed that SiNWs were conformally coated with ATA although the cross-sectional shapes of MACE-SiNWs were non-uniform and sharp spikes can be seen locally. The dielectric capacitance density of 5.9 μF/cm2 at V = −4 V of the perfect accumulation region was achieved due to the combination of the large surface area of the SiNW array and the high dielectric constant of ATA. The capacitance changed exponentially with the voltage at V < −4.3 V and the capacitance of 84 μF/cm2 was successfully achieved at V = −10 V. It was revealed that not only 3D structure and high-k material but also local nanostructure of SiNWs and stacked dielectric layers could contribute to the considerable high ca... [more]

One of the most important tasks when drilling a borehole is to select the appropriate type of drilling fluid and adjust its properties to the borehole’s conditions. This ensures the safe and effective exploitation of the borehole. Many types of drilling fluids are used to drill holes for crude oil and natural gas. Most often, mainly due to cost and environmental constraints, water-based muds are used. On the other hand, invert drilling fluids are used for drilling holes in difficult geological conditions. The ratio of the oil phase to the water phase in invert drilling fluids the most common ratio being from 70/30 to 90/10. One of the disadvantages of invert drilling fluids is their cost (due to the oil content) and environmental problems related to waste and the management of oily cuttings. This article presents tests of invert drilling fluids with Oil-Water Ratio (OWR) 50/50 to 20/80 which can be used for drilling HPHT wells. The invert drilling fluids properties were examined and th... [more]

The internal fractures in coal and rock mass are important factors affecting the safety of underground engineering such as coalbed methane exploitation, so the comprehensive properties of materials used to seal the fractures are particularly critical. In this paper, firstly, the indexes of the main factors affecting the plugging material (viscosity, bleeding rate, setting time, and strength) were analyzed. Then, the sensitivity of the materials used to seal the fractures was studied and discussed using a principal component analysis and response surface analysis (RSM-PCA). The primary conclusions are as follows: (1) Bleed rate and setting time were the first principal components affecting the comprehensive properties of the plugging materials, and compressive strength was the second principal component. (2) The regression equation was established to characterize the comprehensive properties of the integrated plugging materials, and the optimal mix ratio was 34% of cement content, 11% o... [more]

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Organic waste materials were divided into six basic groups as follows: paper, cardboard, textiles, plastics, hygiene waste, and biodegradable waste. For each group, two waste materials were selected to be studied. Research materials were (i) paper (receipts, cotton wool); (ii) cardboard (cardboard, egg carton); (iii) textiles (cotton, leather); (iv) plastics (polyethylene (PET), polyurethane (PU)); (v) hygiene waste (diapers, leno); and (vi) biodegradable waste (chicken meat, potato peel). Waste materials were chosen to represent the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to the Coats−Redfern method were determined. The pyrolysis activation energy... [more]

Phase change materials have been overwhelmingly used for thermal energy storage applications. Among organics, fatty acids are an important constituent of latent heat storage. Most of the saturated fatty acid PCMs so far studied are either unary or binary constituents of pure fatty acids. In the present study, ternary blends of saturated fatty acids i.e., capric, lauric, myristic, stearic, and palmitic acids have been developed with different weight proportions. A series of 28 ternary blends viz. CA-LA-MA, CA-LA-PA, CA-LA-SA, CA-MA-PA, CA-MA-SA, and CA-PA-SA were prepared and analyzed with differential scanning calorimetry, thermal gravimetric analysis, and Fourier transform infrared spectroscopy. DSC analysis revealed that the prepared materials lie in the 15−30 °C temperature range. Also, 300 thermal melt/freeze cycles were conducted which showed ±10% variation in terms of the melting peak for most of the PCMs, with the average latent heat of fusion between 130 and 170 kJ/kg. The TGA... [more]

In this study, corn cob was used as raw material and modified methods employing KOH and KMnO4 were used to prepare activated carbon with high adsorption capacity for mercury ions. Experiments on the effects of different influencing factors on the adsorption of mercury ions were undertaken. The results showed that when modified with KOH, the optimal adsorption time was 120 min, the optimum pH was 4; when modified with KMnO4, the optimal adsorption time was 60 min, the optimal pH was 3, and the optimal amount of adsorbent and the initial concentration were both 0.40 g/L and 100 mg/L under both modified conditions. The adsorption process conforms to the pseudo-second-order kinetic model and Langmuir model. Scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and Zeta potential characterization results showed that the adsorption process is mainly physical adsorption, surface c... [more]

Underground coal gasification (UCG) technology converts deep coal resources into synthesis gas for use in the production of electricity, fuels and chemicals. This study provides an overview of the systematic methods of the in situ coal gasification process. Furthermore, the model of the porous structure of coal has been presented and the gas movement taking place in the carbon matrix—which is part of the bed—has been described. The experimental tests were carried out with the use of air forced through the nozzle in the form of a gas stream spreading in many directions in a porous bed under bubbling conditions. The gas flow resistance coefficient was determined as a function of the Reynolds number in relation to the diameter of the gas flow nozzle. The proprietary calculation model was compared to the models of many researchers, indicating a characteristic trend of a decrease in the gas flow resistance coefficient with an increase in Reynolds number. The novelty of the study is the dete... [more]

Power systems rely on ancillary services (ASs) to ensure system security and stability. Until recently, only the conventional power generation resources connected to the transmission grids were allowed to provide these ASs managed by the transmission system operators (TSOs), while distribution system operators (DSOs) had a more passive role, focused on guaranteeing distribution capacity to bring power to final consumers with enough quality. Now, with the decarbonization, digitalization and decentralization processes of the electrical networks, the growing integration of distributed energy resources (DERs) in distribution grids are displacing conventional generation and increasing the complexity of distribution networks’ operation, requiring the implementation of new active and coordinated management strategies between TSOs and DSOs. In this context, DERs are becoming potential new sources of flexibility for both TSOs and DSOs in helping to manage the power system. This paper proposes a... [more]

The amelioration of photovoltaic (PV) and photovoltaic/thermal (PV/T) systems have garnered increased research interest lately, more so due to the discovery of the thermal property augmentation of nanofluids. The overarching goal of this study is to conduct a comparative analysis of mono, hybrid, and ternary hybrid nanofluids utilized as fluids for heat transfer applications and particularly as cooling mediums in PV/T applications. Al2O3, ZnO, Al2O3-ZnO, and Al2O3-ZnO-Fe3O4 nanofluids are synthesized at 1% volume concentration using the two-step method. The zeta potential tests carried out showed that the fluids have high stability. The numerical model developed in this study was validated using real data culled from Cyprus International University. The findings in this study showed that the Al2O3-ZnO-Fe3O4 ternary hybrid nanofluid and ZnO mono nanofluid were more efficient heat transfer fluids for the PV/T system. The optimum relative electrical PV/T efficiency against that of the PV... [more]

This paper presents the methodology of material parameters’ estimation for the dual-phase-lag (DPL) model at the nanoscale in modern integration circuit (IC) structures. The analyses and measurements performed were used in the unique dedicated micro-electro-mechanical system (MEMS) test structure. The electric and thermal domain of this structure was analysed. Finally, the silicon dioxide (SiO2) temperature time-lag estimation procedure is presented based on the scattering parameters measured by a vector network analyser for the considered MEMS structure together with the 2-omega method. The proposed methodology has the ability to estimate the time-lag parameter with high accuracy and is also suitable for the temperature time-lag estimation for other manufacturing process technologies of ICs and other insulation materials used for integrated circuits such as silicon nitride (Si3N4), titanium nitride (TiN), and hafnium dioxide (HfO2).

Advances in Infrared (IR) cameras, as well as hardware computational capabilities, contributed towards qualifying vision systems as reliable plasma diagnostics for nuclear fusion experiments. Robust autonomous machine protection and plasma control during operation require real-time processing that might be facilitated by Graphics Processing Units (GPUs). One of the current aims of image plasma diagnostics involves thermal events detection and analysis with thermal imaging. The paper investigates the suitability of the NVIDIA Jetson TX2 Tegra-based embedded platform for real-time thermal events detection. Development of real-time processing algorithms on an embedded System-on-a-Chip (SoC) requires additional effort due to the constrained resources, yet low-power consumption enables embedded GPUs to be applied in MicroTCA.4 computing architecture that is prevalent in nuclear fusion projects. For this purpose, the authors have proposed, developed and optimised GPU-accelerated algorithms w... [more]