A non-Newtonian stagnation point fluid flow towards two different inclined heated surfaces is mathematically formulated with pertinent effects, namely mixed convection, viscous dissipation, thermal radiations, heat generation, and temperature-dependent thermal conductivity. Mass transfer is additionally considered by the use of a concentration equation. The flow narrating equations are solved numerically by using the shooting method along with the Runge−Kutta scheme. A total of 80 samples are considered for five different inputs, namely the velocities ratio parameter, temperature Grashof number, Casson fluid parameter, solutal Grashof number, and magnetic field parameter. A total of 70% of the data are used for training the network; 15% of the data are used for validation; and 15% of the data are used for testing. The skin friction coefficient (SFC) is the targeted output. Ten neurons are considered in the hidden layer. The artificial networking models are trained by using the Levenber... [more]

Drying has been widely studied as a necessary process in biomass utilization. The steam diffusion law plays an important role in drying kinetics. The drying kinetics of a single biomass particle using Fick’s second law of diffusion was studied in this paper. A parabolic relationship appeared between the critical moisture content and temperature. The critical moisture content decreased with the increase in drying temperature and the initial moisture content. The drying temperature had a significant effect on the effective diffusivity and coefficient of mass transfer during the dramatically falling period of the biomass drying process. However, it was affected by the effective diffusivity and coefficient of mass transfer during the slowly falling period. The initial moisture caused the opposite effect during the different periods. The normalized biomass moisture content generally increased with the increase in drying temperature, and decreased with the increase in initial moisture conten... [more]

Landslide susceptibility analysis has become a necessary means of pre-disaster portal positioning and scientific early warning. How can an effective zoning model of landslide susceptibility be established to examine the important factors affecting landslide development in coal mine areas? Focusing on the need for a reliability analysis of landslide susceptibility in coal mine areas, landslide cataloging and environmental factor data were used as objects, combined with the knowledge of landslide mechanisms, disaster environmental factors and the spatial correlation of landslide disasters, the frequent landslide area of Jiumine in the main part of Xishan Coalfield was selected as the research area, and more than 50 influencing factors were collected and calculated. Eighteen factors with correlation coefficients of less than 0.3 were selected, and a landslide susceptibility analysis method combining the spatial characteristics of landslide factors and the heuristic fuzzy logic model was p... [more]

Microfluidics, as one of the most valuable analytical technologies of this century, has played an important role in various fields. Particularly, out-of-channel microfluidics, often referred to as open microfluidics (OMF) has recently drawn wide research attention among scholars for its great potential in convenient manual intervention. Much recent research has been geared toward bare droplets and particle-armed droplets (namely liquid marbles, LMs), which could serve as independent systems in OMF. Their versatile applications include but are not limited to nanomaterials preparation, energy harvesting, cell culture and environment monitoring. These applications are mainly attributed to the excellent independence, low reagent consumption and short reaction time of separate droplets and LMs. In addition, more operation features, such as diverse handling options, flexible controllability and high precision, further enable droplets and LMs carrying small liquid biochemical samples to be ma... [more]

During the service of a landfill, uneven soil settlement and earthquakes can cause changes to the pore structure and cracks in the covering layer. The use of a biochar−methanotroph−clay mixture as a new landfill covering layer, can improve its engineering properties. The biochar−methanotroph−clay mixture’s shear-wave velocity and compression-wave velocity were measured by the bender−extender element test, and the elastic parameters under small-strain conditions, such as maximum shear modulus, Gmax, maximum constrained modulus, Mmax, and Poisson’s ratio, ν, were obtained. The parameters showed that the elastic characteristics and lateral deformation capacity were of great significance for settlement, seismic field, and stress−strain analysis. Based on the bender−extender element test, the effects of different compaction degrees, and biochar content on Gmax, Mmax, and ν of the biochar−clay mixture, and different methane cultivation days on the biochar−methanotroph−clay mixture, were inve... [more]

Hydraulic synchronous control systems are widely used in various industrial fields. This paper deeply analyzes the research status and development trend of the hydraulic synchronous control system. Firstly, it gives a brief introduction of the research significance control theory and control methods of the hydraulic synchronous control system. Secondly, the hydraulic synchronization control system is classified, the synchronization error is analyzed, and some solutions to synchronization error are given. Then, according to the classification of the hydraulic synchronous control system, relevant research is carried out. In this paper, three control modes (equivalent, master−slave and cross-coupling) and related control algorithms (fuzzy PID control, sliding mode control, robust control, machine learning control, neural network control, etc.) of closed-loop hydraulic synchronous control systems are studied in detail. Finally, the development trend of the hydraulic synchronization control... [more]

Due to the complexity of risk factors in constructing immersed tube tunnels, it is impossible to accurately identify risks. To solve this problem, and the uncertainty and fuzziness of risk factors, a risk assessment method for immersed tube tunnel construction was proposed based on WBS-RBS (Work Breakdown Structure-Risk Breakdown Structure), improved AHP (analytic hierarchy process), and cloud model theory. WBS-RBS was used to analyze the risk factors of immersed tube tunnel construction from the aspects of the construction process and 4M1E, and built a more comprehensive and accurate construction risk index system. The weight of each index was calculated by the improved AHP of a genetic algorithm. The cloud model theory was used to build the cloud map of risk assessment for immersed tunnel construction and evaluate construction risk. Taking the Dalian Bay subsea tunnel project as an example, the risk assessment method of immersed tunnel construction was verified. The results showed th... [more]

Drying is one of the methods used for preserving fruits and vegetables. However, due to the lengthy process and elevated temperature of convective drying, other pretreatment and drying methods are studied to shorten the drying time and obtain high-quality products. This study aimed to examine the effect of ultrasonic (US) pretreatment and microwave−hot air drying (MW−HA) on the drying time, specific energy (SEC), qualitative properties (e.g., color, shrinkage, and rehydration ratio), and bioactive compound properties (e.g., antioxidant activity, phenolic, and flavonoid contents) of hawthorn fruit. Experiments were performed using ultrasound pretreatment and a microwave dryer (microwave power: 180, 360, and 540 W) at air temperatures of 40, 55, and 70 °C. Drying of hawthorn lasts from 35 min for the ultrasound-treated sample (dried at 540 W and 70 °C) to 180 min (dried at 180 W and 40 °C without US treatment). The lowest amount of SEC (24.11 MJ/kg) was obtained using the US−MW−HA air dr... [more]

Significant efforts have been made toward developing sustainable reduction reactions of organic and bioorganic compounds. In these studies, the selection of reagents and solvents has played a very important role in the development of environment-friendly methodologies. In this context, the reducing agent Cp2TiCl/H2O has been introduced as a safe, efficient, selective, and low-cost reagent, and thus as a sustainable alternative for the reduction of organic compounds. To facilitate understanding of the reductions mediated by this system, in this study we focus on describing the intermediates, mechanisms, and representative examples. Finally, a reflection is made on the future perspectives of this reducing agent, including its analog Cp2TiCl/D2O as a powerful tool for the preparation of deuterated phenols, which can be successfully used as an internal standard for analyzing bioactive phenols in olive oil.

is a halophyte indigenous to marine coastal areas and salt fields and has been used as a traditional remedy for diarrhea, abdominal pain, constipation, and indigestion. Its component isorhamnetin-3-O-glucoside (IR3G) may have antioxidant, anti-inflammatory, and anti-adipogenic properties. In the present study, we aimed to investigate the anti-obesity effect of S. herbacea extract and IR3G on mouse 3T3-L1 adipocytes and db/db obesity mice. S. herbacea extract and IR3G inhibited lipase in a concentration-dependent manner. Oil Red O staining disclosed that S. herbacea extract and IR3G significantly suppressed lipid accumulation and adipogenesis and also inhibited the expression of the C/EBPα in the 3T3-L1 adipocytes. In experiments using db/db mice, administering of S. herbacea extract limited body weight gain and significantly reduced feed efficiency and adipose tissue weight. Moreover, analyzing blood triglycerides, total cholesterol, high-density lipoprotein, and low-density lipoprotei... [more]

The formation of a rich underground-seam network is the key problem in the development of low-permeability hot dry rock (HDR) resources. Considering the lack of macroscopic continuum theory to study hydraulic fracturing having preset fracture-interface element, the particle-flow method of micro-mechanical discrete-element theory is introduced to simulate the mechanical behavior of hydraulic fracturing for HDR low permeability reservoirs. The reservoir is simulated as a round particle; the fracturing fluid movement is described by the seepage field equation, and rock movement is described by the displacement field equation. Finally, the particle-flow numerical model of hydraulic fracturing for HDR low permeability reservoirs is established under the condition of fluid-solid coupling: the model contains two parts (rock and fracture). Based on the parallel-bond model, a definition of micro-fractures of hydraulic fracturing is given. The relation between the fracturing effect and influence... [more]

Waste glass (WG), as a nonbiodegradable material, poses a threat to environmental protection. The reuse of WG as a raw material to replace cement or aggregate in concrete production is gaining attention for recycling purposes. However, the optimal proportion of WG in concrete mixtures and its particle size distribution are hard to determine. Large glass particles are prone to leading to the undesirable alkali−silica reaction (ASR) in concrete. Therefore, in this study, cement and aggregate in concrete mixtures are partially replaced by combinations of glass powder (<30 μm) and glass beads (0.2−1.7 mm), respectively. Glass concretes (GCs) containing waste glass at various replacement ratios (0, 10, 15, 20, and 30%) are prepared, and their flowability and compressive strength are evaluated and compared. Finally, steel tubes filled by ordinary concrete (OCFSTs) and steel tubes filled by glass concrete (GCFSTs) are fabricated and tested in axial compression. The test results show that t... [more]

Second-generation biodiesel, which is produced from essential oil plants, has important advantages, including a high yield of biofuels and the potential to reduce greenhouse gas emissions. The goal of this research was to examine the profile of original and review articles on biodiesel production from essential oils using bibliometric analysis. The search strategy identified 186 relevant and available peer-reviewed publications from 1981 to 2023, which were downloaded from the Web of Science (WoS) database. The retrieved documents were analyzed using VOSviewer. China was the predominant country publishing those documents, followed by the United States, India, Australia, and France. The keyword cluster analysis indicated the presence of 10 main research topics: diesel, fuel, and engine performance; extraction of lipids from microalgae; biofuel production from essential oils; green chemistry; the pyrolysis process; bioethanol production from renewable raw materials; obtaining biodiesel f... [more]

Nowadays, energy conversion plays a crucial role in sustainable growth and development [...]

For the sake of understanding the mechanism of deep subcriticality and high heterogeneity of neutron fluence rate in time−space on the neutron kinetics of the Accelerator-driven Subcritical Reactor Subcritical Reactor (ADSR) under varied beam transients and neutron spectra. A Monte Carlo homogenization approach for the neutron time−space kinetics of the ADSR is proposed in this study, and the influence mechanism on the kinetic parameters of the ADSR under varied neutron spectra, subcriticality, and beam transients is examined. The results show that the Monte Carlo homogenization for the α eigenvalue mode is more adaptable to the subcriticality characteristics under varied subcriticality; under beam transients, the relative differences in the kinetic parameters of the different modes of the ADSR with fast/thermal spectra increase with the depth of subcriticality, and the differences in neutron generation time for varied modes are larger than those of effective fraction of delayed neutro... [more]

The paper presents the possibilities of low-emission-powered vehicles based mainly on compressed hydrogen. It shows currently used forms of powering vehicles based on their genesis, process of obtention, and popularity. They are also compared to each other, presenting the advantages and disadvantages of a given solution. The share of electricity in transport, its forecasts for the future, and the possibilities of combination with conventional energy sources are also described. Based on current technological capabilities, hydrogen plays a crucial role, as presented in the above work, constituting a fundamental basis for future transport solutions.

Continuous global economic and population growth has driven the ever-increasing demand for energy [...]

Wettability in CO2-brine-mineral/rock systems is an important parameter influencing CO2 storage capacities and leakage risks in saline reservoirs. However, CO2 tends to react with various minerals and rocks at subsurface conditions, thus causing temporal and spatial wettability changes. Although many relevant research works have been published during past years, a thorough overview of this area is still lacking. Therefore herein, reaction-induced wettability changes are reviewed, and the underlying mechanisms are discussed. Current research gaps are identified, future outlooks are suggested, and some conclusions are drawn. The fundamental understanding of reaction-induced mineral and rock wettability changes during CO2 storage in saline reservoirs is analyzed and the guidance for long-term CO2 containment security evaluations is provided.

This paper presents the application of prediction in the analysis of market price volatility in Polish conditions of wood processing by-products in the form of biomass. The ARIMA model, which takes into account cyclical, seasonal, irregular fluctuations of historical data on the basis of which the forecast and long-term trends of selected wood products were made, was used in predicting prices. Comparisons were made between the ARIMA prediction method and the multiplicative Winters−Holt model. During the period studied (2017−2022), the changes in the market price of biomass were characterized by a wide spread of values. On average, the price of these products increased from 2017 to the end of 2022 by 125%. The price prediction analysis showed seasonal fluctuations in the case of wood chips. The uncertainty in price prediction is due to changes in supply resulting from the influence of global factors. The Diebold−Mariano test of matching accuracy confirms that the price prediction of the... [more]

In recent years, the safety of oil and gas pipelines has become a primary concern for the pipeline industry. This paper presents a comprehensive study of the vulnerability concepts that may be used to measure the safety status of pipeline systems. The origins of the vulnerability concepts are identified, the development and evolution of the vulnerability concepts are described, and the main connotations of the four levels of vulnerability concepts applied in different fields at this stage are summarized. Qualitative and quantitative methods of vulnerability assessment are comprehensively investigated, and the advantages and disadvantages, scope of application and key issues faced are compared and summarized. The research and analysis show that the vulnerability assessment of oil and gas pipelines is at a preliminary stage, and there is an urgent demand to establish a unified vulnerability concept and assessment system for oil and gas pipeline systems. The current qualitative or semi-qu... [more]

In our paper we analyse the scientific perception of energy use in the social sciences [...]

In the past few years, internet celebrities have become a new and important way to get people to buy energy-saving products. Their psychological mechanisms for promoting fans’ intention to purchase have become the focus of academic attention, but a unified conclusion has yet to be reached. This study uses online communities as a scenario, with the characteristics of influencers’ expertise, social attraction, and task attraction as antecedent variables and social cognitive theory and parasocial interaction theory as the theoretical basis to explore their influence on fans’ intention to purchase household energy-saving products. The study investigates the mediating role of parasocial relationships and the moderating role of fans’ green self-efficacy in influencing internet celebrities’ expertise and attraction of fans’ parasocial relationships. The results showed that the parasocial relationships formed between fans and influencers mediated the relationship between the expertise and attr... [more]

The increasing demand for electricity and the need for environmentally friendly transportation systems has resulted in the proliferation of solar photovoltaic (PV) generators and electric vehicle (EV) charging within the low voltage (LV) distribution network. This high penetration of PV and EV charging can cause power quality challenges, hence the need for hosting capacity (HC) studies to estimate the maximum allowable connections. Although studies and reviews are abundant on the HC of PV and EV charging available in the literature, there is a lack of reviews on HC studies that cover both PV and EVs together. This paper fills this research gap by providing a detailed review of five commonly used methods for quantifying HC including deterministic, time series, stochastic, optimization, and streamlined methods. This paper comprehensively reviews the HC concept, methods, and tools, covering both PV and EV charging based on a survey of state-of-the-art literature published within the last... [more]

The possibilities for reducing the fuel consumption of internal combustion engines focus mainly on developing combustion systems, as one such solution is a two-stage combustion system using jet ignition. The combustion of gaseous mixtures with a high excess air ratio leads to an increase in overall efficiency and a reduction in the emissions of selected exhaust components. In such a convention, gas combustion studies were conducted in the methane/propane configuration. Using an active prechamber where spark plugs were placed and direct injection through a check valve, the fuel dose was minimized into the prechamber. The tests were conducted for a constant center of combustion (CoC). The combustion process in both the prechamber and main chamber was analyzed using a test stand equipped with a 0.5 dm3 single-cylinder engine. The engine was controlled by varying the fuel supply to the prechamber and main chamber in excess air ratio λ = 1.3−1.8. The study analyzed thermodynamic indices suc... [more]

Delamination damage to spar caps seriously endangers the operation safety of offshore wind turbines. The effect of initial delamination of various depths and areas on the ultimate tensile load of laminates is studied based on experiments and numerical simulation, and an effective method for predicting the residual tensile strength of laminates with high thickness is proposed. Three groups of initial delamination specimens with different characteristics were fabricated, and static displacement tensile tests were carried out. An accurate three-dimensional numerical analysis model was established, and the results were in good agreement with the experimental values, with the overall error of the failure load being less than 6%. Furthermore, a numerical model for a 20-ply high-thickness spar cap laminate was established to predict the effect of delamination on tensile strength. The results showed that, for the same depth of initial delamination, the difference in delamination area had littl... [more]