Solar energy is planned to undergo large-scale deployment along with Thailand’s transformation to a carbon neutral society in 2050. In the course of energy transformation planning, the issue of energy infrastructure adaptation to climate change has often been left out. This study aims to identify climate-related risks and countermeasures taken in solar power plants in Thailand using thematic analysis with self-administered observations and structured interviews in order to propose points of consideration during long-term energy planning to ensure climate adaptation capacity. The analysis pointed out that floods and storms were perceived as major climate events affecting solar power plants in Thailand, followed by lightning and fires. Several countermeasures were taken, including hard countermeasures that require extensive investment. Following policy recommendations were derived from the climate-proofing investment scenario study. Policy support in terms of enabling regulations or fina... [more]

Recent trends in the photovoltaic (PV) technology industry are moving towards utilizing bifacial PV panels. Unlike traditional PV panels, bifacial PV panels can yield energy from both sides of the panel. Manufacturers specify that bifacial PV panels can harness up to 30% more energy than traditional PV panels. Hence, bifacial PV panels are becoming a common approach at low solar irradiance conditions to yield more energy. However, a bifacial PV panel increases PV inverter loading. The PV inverter is the most unreliable component in the entire PV system. This results in a negative impact on PV system reliability and cost. Hence, it is necessary to anticipate the inverter’s reliability when used in bifacial PV panels. This paper analyzes the reliability, i.e., lifetime, of PV inverters, considering both monofacial and bifacial PV panels for the analysis. Results showed that the increase in bifacial energy yield could significantly affect PV inverter reliability performance, especially in... [more]

Despite its recent growth in popularity, actively heated clothing still lacks the ability to cope with demanding user scenarios. As many of these deficiencies stem from an absence of automatic control, the authors propose a novel approach using a set of sensors embedded in the clothing to provide data about thermal comfort. Available sensors suffer from a lack of accuracy, as for practical reasons, they cannot be attached to the skin, whose temperature is usually used as a comfort indicator. To determine the magnitude of the problem, the authors conducted experiments, and a thermal model was proposed based on experimental findings; the output from the model was compared with the experimental reference data for three different upper body undergarments. The overall accuracy was found to be good: in most cases, the difference between the computed and reference skin temperatures did not exceed 0.5 °C. Furthermore, the model does not rely on unrealistic assumptions regarding the availabilit... [more]

An investigation of the effects of wind gusts on the directly interconnected wind generators is reported, and techniques toward the mitigation of the wind gust negative influences have been proposed. Using a directly interconnected system approach, wind turbine generators are connected to a single synchronous bus or collection grid without the use of power converters on each turbine. This bus can then be transformed for transmission onshore using High Voltage Alternating Current, Low-Frequency Alternating Current or High Voltage Direct Current techniques with shared power conversion resources onshore connecting the farm to the grid. Analysis of the potential for instability in transient conditions on the wind farm, for example, caused by wind gusts is the subject of this paper. Gust magnitude and rise time/fall time are investigated. Using pitch control and the natural damping of the high inertial offshore system, satisfactory overall system performance and stability can be achieved du... [more]

In the last decades, a large focus is being placed on the sustainability and safety of the power transformer spectrum. Ester liquids, which have interesting properties such as high fire point and biodegradability, are gaining needed attraction. Since in-service condition, thermal aging deteriorates the physicochemical and electrical properties of liquid dielectrics, it is important to study their long-term behavior. In this contribution, the pre-breakdown and breakdown behavior of ester fluids (synthetic and natural) under AC stress are investigated. Important characteristics, such as partial discharge pre-inception voltage, partial discharge inception voltage, breakdown voltage, average streamer velocity, and inception electric field, were assessed. The influence of the radius of curvature (of high voltage needle electrode) as well as the thermal degradation of typical ester liquids are also discussed. Mineral oil was also included in the tests loop as a benchmark for comparative purp... [more]

In this paper, a two-bladed medium-sized floating wind turbine with variable speed and power regulation by stall is studied. For floating offshore wind turbines, the major challenges are related to the dynamical behavior of the system in response to combined wind and wave loading. Especially for smaller systems, the coupling of aerodynamic and wave forces may lead to large amplitude motions. Coupled aero-hydro-servo-elastic simulations are carried out in OpenFAST. The goal of the study is to investigate the global dynamic response of the hypothetical wind turbine with stall regulation. Stall regulation concept is proposed and the structural loads are computed and results are presented and discussed.

From the environmental perspective, wooden structures are favorable insulators that are suitable for carbon fixation and wooden-related products are considered the most sustainable material. Research has indicated that wooden structures have superior energy-saving performance compared to reinforced concrete (RC) structures. In this study, a CLT-based hybrid structure system that potentially improves the efficiency of energy consumption is proposed. The proposed hybrid structure system, which preserved original RC beams, columns and replaced CLT floors and walls, has less building weight compared to the original RC building. Additionally, less energy required for the manufacturing of building materials in the renovation of the aged building is achieved, compared to building a new CLT building. The energy consumptions for buildings with heights of 10 stories were compared. CLT and RC were selected as benchmark building materials to compare the energy-saving efficiencies with the proposed... [more]

This article presents the influence of climatic conditions on surface water quality. The research methodology, including physicochemical analysis from the Gołdapa and Bludzia rivers, is presented. The research lasted for two years. The results of the physicochemical studies of the Gołdapa and Bludzia rivers in early spring, spring, and autumn show that each of these seasons impacts the quality of surface waters. Moreover, it was proven that all the parameters are strongly correlated with the air temperature, the sum of daily precipitation, and water levels. For detailed analysis, the obtained results of own research were compared with meteorological and hydrological data from the last 15 years (2005−2021) for the region of north-eastern Poland. It was proven that temperature changes contribute to increased surface water pollution in the north-eastern part of Poland. Waters from areas that humans have not developed are of better quality than those that drain the urban area, which is ref... [more]

A distributed electric vehicle (EV) charging scheduling strategy with transactive energy (TE) management is presented in this paper to deal with technical issues in distribution network operation and discuss the economic benefits of EV charging. At an individual EV level, EV owners propose bids to actively participate in the distribution system operation. At the node level, an electric vehicle aggregator (EVA) optimally allocates the available charging power to meet EV charging requirements and cost benefits. At the distribution network level, a distribution system operator (DSO) integrates an electricity price market clearing mechanism with the optimal power flow (OPF) technique to ensure the reliability of the distribution network. Moreover, a distributed algorithm is discussed for solving the EV charging problem with transactive energy management (TEM). The clearing electricity price is achieved through a negotiation process between the DSO and EVAs using the alternating direction m... [more]

The recovery of oil and gas from underground reservoirs has a pervasive impact on petroleum-producing companies’ financial strength. A significant cause of the low recovery is the plugging of reservoir rocks’ interconnected pores and associated permeability impairment, known as formation damage. Formation damage can effectively reduce productivity in oil- and gas-bearing formations—especially in sandstone reservoirs endowed with clay. Therefore, knowledge of reservoir rock properties—especially the occurrence of clay—is crucial to predicting fluid flow in porous media, minimizing formation damage, and optimizing productivity. This paper aims to provide an overview of recent laboratory and field studies to serve as a reference for future extensive examination of formation damage mitigation/formation damage control technology measures in sandstone reservoirs containing clay. Knowledge gaps and research opportunities have been identified based on the review of the recent works. In additio... [more]

The present work performed a comprehensive investigation to find the effects of a dual-bleeding port recirculation channel on the aerodynamic performance of a single-stage transonic axial compressor, NASA Stage 37, and optimized the channel’s configuration to enhance the operating stability of the compressor. The compressor’s performance was examined using three parameters: The stall margin, adiabatic efficiency, and pressure ratio. Steady-state three-dimensional Reynolds-averaged Navier−Stokes analyses were performed to find the flow field and aerodynamic performance. The results showed that the addition of a bleeding channel increased the recirculation channel’s stabilizing effect compared to the single-bleeding channel. Three design variables were selected for optimization through a parametric study, which was carried out to examine the influences of six geometric parameters on the channel’s effectiveness. Surrogate-based design optimization was performed using the particle swarm op... [more]

The implementation of a dual electric system that is capable of operating with either constant current and variable voltage, or constant voltage and variable current appliances, is one of the possible options to solve low-intensity stochastic energy utilization problems from renewable energy sources. This research paper analyzes the potential benefit of a novel three-phase dual system power inverter over the conventional inverter used in a solar power plant. The concept of such a power inverter is explained, and the digital twin model is created in a MATLAB Simulink environment. The efficiency characteristic of the simulated inverter is compared to the efficiency characteristic of a real conventional inverter. A standalone data logging system and an additional data acquisition system were used to collect and process data from the real inverter. Comparison of the digital twin inverter and the real conventional inverter shows the potential benefit of this novel inverter technology. It is... [more]

The study posed a research question: did the situation caused by COVID-19 affect the economic position of energy companies? The aim of the study is to investigate the impact of the situation of the epidemic state introduced in 2020 on the activities of the efficiency of energy sector companies. The subject of the research will be the ten largest Polish power plants in terms of electricity production, including four capital groups to which they belong. Financial data from 2014 to 2020 will be used for the research. To test the effectiveness, the tools of the ratio analysis will be used. The analysis of the financial statements in terms of investments in manufacturing activities confirms the hypothesis that companies investing in new solutions and technologies will be best prepared for an exceptional situation. The results of the research show that those capital groups which in the period preceding the outbreak of the epidemic made the largest investment outlays and at the same time thei... [more]

Located in a semi-arid to arid region, Morocco is confronting increasing water scarcity challenges. In the circular economy paradigm, the reuse of treated wastewater in agriculture is currently considered a possible solution to mitigate water shortage and pollution problems. In recent years, Morocco has made significative progress in urban wastewater treatment under the National Wastewater Program (PNA). However, rural sanitation has undergone significant delays. Therefore, an alternative technology for wastewater treatment and reuse in rural areas is investigated in this review, considering the region’s economic, social, and regulatory characteristics. Constructed wetlands (CWs) are a simple, sustainable, and cost-effective technology that has yet to be fully explored in Morocco. CWs, indeed, appear to be suitable for the treatment and reuse of wastewater in remote rural areas if they can produce effluent that meets the standards of agricultural irrigation. In this review, 29 studies... [more]

Economical and environmental concerns have forced the oil and gas industry to consider reusing flowback and produced water for fracturing operations. The major challenge is that the high-salinity of flowback water usually prevents its compatibility with several fracturing fluid additives. In this paper, the authors explored an economic and effective method to prepare guar fracturing fluids with different salinity waters. The main research idea was to use chelating agents to mask metal ions, such as calcium and magnesium, that are harmful to crosslinking. Firstly, a complexometric titration test was conducted to measure the chelating ability of three chelating agents. Secondly, through viscosity, crosslinking, and hanging tests, it was verified that the complex masking method could cope with the problem of high-valence metal ions affecting crosslinking. Thirdly, the preferred chelating agent was mixed with several other additives, including thickeners, crosslinkers, and pH regulators, t... [more]

Solar-powered aircraft can perform long-term flights with clean solar energy. However, the energy derived from solar irradiation is influenced by the time of year and latitude, which limits the energy acquisition ability of solar aircraft with a straight-wing configuration. Hence, unconventional configurations based on increasing wing dihedral to track the sun are proposed to improve energy acquisition at high-latitude regions in winter, which may involve power loss caused by mismatch in the photovoltaic system. However, mismatch loss is seldom considered and may cause energy to be overestimated. In this paper, the energy acquisition characteristics of a joint-wing configuration are presented based on the simulation of an energy system to investigate the mismatch power loss. The results indicate a 4~15% deviation from the frequently used estimation method and show that the mismatch loss is influenced by the curved upper surface, the severity of shading and the circuit configuration. Th... [more]

Waste heat recovery is considered as one of the most promising options to improve the efficiency and sustainability of industrial processes. Even though industrial waste heat is abundantly available and its utilization is not a new concept, the implementation rate of waste-heat recovery interventions in industrial facilities is still low, due to several real or perceived barriers. Foremost challenges are represented by technical, economic, financial and regulatory factors. An additional prominent barrier lies in the lack or incompleteness of information concerning the material and energy flows within the factories, and the types and characteristics of waste heat sources and possible sinks for their internal or external reuse. With the aim to overcome some of the information barriers and increase the willingness of companies to approach waste heat recovery and reuse, a methodology to map waste heat sources and sinks in industrial processes is proposed in this study. The approach here pr... [more]

The aim of the proposed paper is the development of an electro-thermal model of semiconductor component using an indirect modelling approach. The approach is based on the integration of the component’s electrical properties considering non-linear behavior of a V-A characteristic. In this way, the identification of semiconductor material properties considering non-linear dependencies and semiconductor volume is provided. The main aim of the presented approach is simplification of the electro−thermal interaction within finite-element modelling of the semiconductor components. In this way, it is possible to omit more complex boundary definitions and the setting of the semiconductor-based physics. The proposed methodology is presented within the development of a simulation model based on a small high-frequency rectifying diode, taking into account its geometric dimensions and the internal arrangement of its structure. Simulation was performed as a transient analysis, while the results from... [more]

The aim of this work involved comparing the effect graphite and shungite have on the properties of dielectric elastomer-based materials. For this reason, dielectric elastomer−Sylgard (S) was filled with 1, 3, 5, 10, and 15 wt.% of graphite (G) and shungite (Sh). The structure of the obtained materials was studied by means of scanning electron microscopy and atomic force microscopy. The influence of the introduced additives on the thermal stability of the obtained composites was evaluated using thermogravimetry. Moreover, the mechanical properties and the dielectric constant of the elastomer with an addition of graphite and shungite were determined. Obtained results allowed us to establish that the presence of graphite as well as shungite significantly influences mechanical as well as dielectric properties. Additionally, the optimum mass of additives, allowing to increase the dielectric constant without the significant decrease of strain at break, was indicated. In the case of materials... [more]

In order to deepen the understanding of rotating effects on internal cooling, the flow and heat transfer characteristics of 2-pass rotating rectangular smooth/ribbed channels are investigated by Reynolds-Averaged Navier-Stokes (RANS) simulation. Three rotating numbers (Ro = 0.10, 0.25, and 0.40) are simulated, and the maximum buoyancy parameter (Bo) reaches 5.0. The results show that the rotating buoyancy has significant effects on the flow and heat transfer under high Bo conditions. When Bo > 1.0, rotating buoyancy inducts flow separation near the leading edge (LE) in the first passage, while the air flow in the second passage shows a double-peak profile. With increased Bo, the heat transfer in the first passage is greatly increased, and the maximum growth rate occurs at Bo = 0.6~1.0. However, the heat transfer in the second passage has no obvious changes due to a strong turn effect. In the ribbed channel, rotating effects are much weaker than those in the smooth channel. This researc... [more]

In this study, three different environmentally friendly fouling mitigation technologies are suggested and are investigated in reverse electrodialysis (RED) to develop the most appropriate fouling mitigation technology for RED: applying direct current, flowing a solution with high salt concentration, and periodically switching river and seawater streams in RED. The quantitative level of anion exchange membrane fouling mitigation is evaluated in terms of the power density and the amount of power generation of RED. Applying a direct current electric field with higher voltage than 8 V was not allowed for fouling mitigation in the two-cell-pair bench RED stack due to decomposition of the redox couple. In comparison of the RED operations with two different fouling mitigation methods using firstly 40-min power generation during in-operation and 40-min fouling mitigation stage during out-of-operation as a cycle for 80 min and secondly 80-min forward power generation and 80-min backward power g... [more]

Transition metal dichalcogenide (TMD) MoS2 and WS2 monolayers (MLs) deposited atop of crystalline zinc oxide (ZnO) and graphene-like ZnO (g-ZnO) substrates have been investigated by means of density functional theory (DFT) using PBE and GLLBSC exchange-correlation functionals. In this work, the electronic structure and optical properties of studied hybrid nanomaterials are described in view of the influence of ZnO substrates thickness on the MoS2@ZnO and WS2@ZnO two-dimensional (2D) nanocomposites. The thicker ZnO substrate not only triggers the decrease of the imaginary part of dielectric function relatively to more thinner g-ZnO but also results in the less accumulated charge density in the vicinity of the Mo and W atoms at the conduction band minimum. Based on the results of our calculations, we predict that MoS2 and WS2 monolayers placed at g-ZnO substrate yield essential enhancement of the photoabsorption in the visible region of solar spectra and, thus, can be used as a promising... [more]

Ground source heat pumps (GSHPs), a high-efficiency and energy-saving air-conditioning technology that utilizes shallow geothermal resources for both heating and cooling, are a vital green energy system for residential and commercial buildings. Improving the performance of such a system was the focus of the current research. As soil temperature and thermal radius are two important aspects that affect the performance of ground source heat pump systems, we conducted a new numerical simulation to capture the changes in sensitive factors and propose the optimized paths. The numerical simulation analyzed the thermal characteristics of a borefield under different pre-cooling times and soil types. The results indicated the following: (1) The rate of the ground temperature change with pre-cooling during the discharging period had a faster rise than in the case without pre-cooling. The longer the precooling time was, the smaller the thermal radius became. In particular, when the precooling time... [more]

Short-term load forecasting is an important part of load forecasting, which is of great significance to the optimal power flow and power supply guarantee of the power system. In this paper, we proposed the load series reconstruction method combined improved complete ensemble empirical mode decomposition with adaptive noise (ICEEMDAN) with sample entropy (SE). The load series is decomposed by ICEEMDAN and is reconstructed into a trend component, periodic component, and random component by comparing with the sample entropy of the original series. Extreme learning machine optimized by salp swarm algorithm (SSA-ELM) is used to predict respectively, and the final prediction value is obtained by superposition of the prediction results of the three components. Then, the prediction error of the training set is divided into four load intervals according to the predicted value, and the kernel probability density is estimated to obtain the error distribution of the training set. Combining the pre... [more]

Landfills are elements of the waste management system, without possibility of further reclaiming, according to the requirements of a closed-loop economy, but with the possibility of transforming the area into other functions. The research combined monitoring of plant species, suggesting the composition of vegetation cover for pro-ecological management, analysis of functional and infrastructural incorporation of the landfill in the surrounding landscape, and proposals for reclamation and social application. An assessment of geotechnical safety was also made. Modernization of the landfill suggests that the pressure placed on other untouched locations should decrease. The designed space allows reintroducing socio-ecological life into this degraded area. Taking advantage of the character of the area, including variable development and significant landscape potential on the outskirts of a large city in the vicinity of protected areas, there is the possibility of creating new spatial quality... [more]