In a combustion reaction of hydrocarbon fuel, carbon monoxide (CO) is a gas species that is closely related to air pollution generation and combustion efficiency. It has a trade-off with nitrogen oxide and increases rapidly in case of incomplete combustion or in fuel-rich (Φ > 1) environments. Therefore, it is essential to measure CO concentration in order to optimize the combustion condition. In the case of a steel annealing system, the combustion environment is maintained in a deoxidation atmosphere to prevent the formation of an oxide layer on the steel sheet surface. However, it is difficult to measure the CO concentration in a combustion furnace in real-time because of the harsh environment in the furnace. Tunable diode laser absorption spectroscopy, which has the advantages of non-invasiveness, fast response, and in situ measurement-based optical measurement, is highly attractive for measuring the concentration of a certain gas species in a combustion environment. In this study,... [more]

Carbon labeling schemes enable consumers to be aware of carbon emissions regarding products or services, to help change their purchasing behaviors. This study provides a bibliometric analysis to review the research progress of carbon labeling schemes during the period 2007−2019, in order to provide insight into its future development. Number of publications, countries of publications, authors, institutions, and highly cited papers are included for statistical analysis. The CiteSpace software package is used to visualize the national collaboration, keywords co-appearance, and aggregation. The results are given as follows: (1) there are 175 articles published in the pre-defined period, which shows a gradual increase, with a peak occurred in 2016; (2) carbon labeling schemes are mainly applied to grocery products, and gradually emerged in construction and tourism. (3) Existing studies mainly focus on examination of utility of carbon labeling schemes, by conducting surveys to investigate i... [more]

The oil-free compressor is a key component in fabricating polyethylene terephthalate (PET) bottles for beverages and water. At present, the main compressor type used for blowing PET bottles is the reciprocating compressor. However, compared to screw compressors, reciprocating compressors have shortcomings of high energy consumption and too many consumable parts. Many manufacturers of PET bottles in Asia are seeking to replace reciprocating compressors with screw compressors, as we know. Screw compressors can be classified as single-screw compressors (SSC) and twin-screw compressors. Since the load in a twin-screw compressor is far larger than that in an SSC, SSCs are more suitable for being developed for high-pressure applications such as PET bottle blowing. This paper presents a performance study on an oil-free single-screw compressor as the first stage of the PET compressor unit. A 5.4 m3·min−1 prototype and its test rig were developed. The thermophysical process of the moist air is... [more]

Plug-in Electric Vehicle (PEV) user charging behavior has a significant influence on a distribution network and its reliability. Generally, monitoring energy consumption has become one of the most important factors in green and micro grids; therefore, predicting the charging demand of PEVs (the energy consumed during the charging session) could help to efficiently manage the electric grid. Consequently, three machine learning methods are applied in this research to predict the charging demand for the PEV user after a charging session starts. This approach is validated using a dataset consisting of seven years of charging events collected from public charging stations in the state of Nebraska, USA. The results show that the regression method, XGBoost, slightly outperforms the other methods in predicting the charging demand, with an RMSE equal to 6.68 kWh and R2 equal to 51.9%. The relative importance of input variables is also discussed, showing that the user’s historical average demand... [more]

Transportation safety, as a critical component of an efficient and reliable transportation system, has been extensively studied with respect to societal economic impacts by transportation agencies and policy officials. However, the embodied energy impact of safety, other than induced congestion, is lacking in studies. This research proposes an energy equivalence of safety (EES) framework to provide a holistic view of the long-term energy and fuel consequences of motor vehicle crashes, incorporating both induced congestion and impacts from lost human productivity resulting from injury and fatal accidents and the energy content resulting from all consequences and activities from a crash. The method utilizes a ratio of gross domestic product (GDP) to national energy consumed in a framework that bridges the gap between safety and energy, leveraging extensive studies of the economic impact of motor vehicle crashes. The energy costs per fatal, injury, and property-damage-only (PDO) crashes i... [more]

In the modern shipboard power system, there is a growing concern about reduced fuel economy, efficiency improvement, and minimized emission in recent years. Besides, considering the islanded nature of the shipboard power system, ensuring the system reliability at both generation and load side is crucial. In this context, a hybrid medium voltage DC (MVDC) distribution system concept with diesel engine, PV system, and battery energy storage system (BESS) as the generators for the shipboard power system is proposed. Variable speed operation of a diesel engine is considered for the benefit of minimal specific fuel oil consumption (SFOC). Regarding the fault-tolerant characteristics of six-phase permanent magnet synchronous machine (PMSM), it is used for both generating and motoring application, thus maintaining system reliability at any time. A hierarchical control system is designed and implemented to ensure proper load power-sharing among the generators and to regulate the dc-link voltag... [more]

Due to the significant increase of the number of wind-based electricity generation systems, it is important to have accurate information on their operational characteristics, which are typically obtained by processing large amounts of measurements from the individual wind turbines (WTs) and from the whole wind farms (WFs). For further processing of these measurements, it is important to identify and remove bad quality or abnormal data, as otherwise obtained WT and WF models may be biased, or even inaccurate. There are wide ranges of both causes and manifestations of these bad/abnormal data, which are often denoted with the common general term “outlier”. This paper reviews approaches for the detection and treatment of outliers in processing WT and WF measurements, starting from the discussion of the commonly measured parameters, variables and resolutions, as well as the corresponding requirements and recommendations in related standards. Afterwards, characteristics and causes of outlier... [more]

The global proliferation of plug-in electric vehicles (PEVs) poses a major challenge for current and future distribution systems. If uncoordinated, their charging process may cause congestion on both network transformers and feeders, resulting in overheating, deterioration, protection triggering and eventual risk of failure, seriously compromising the stability and reliability of the grid. To mitigate such impacts and increase their hosting capacity in radial distribution systems, the present study compares the levels of effectiveness and performances of three alternative centralized thermal management formulations for a real-time agent-based charge control algorithm that aims to minimize the total impact upon car owners. A linear formulation and a convex formulation of the optimization problem are presented and solved respectively by means of integer linear programming and a genetic algorithm. The obtained results are then compared, in terms of their total impact on the end-users and... [more]

In the field of petroleum drilling engineering, passive magnetic ranging technology is generally used for specialized drilling operations such as connecting relief wells, preventing wellbore collisions, guiding parallel horizontal wells, etc. Although pre-magnetized casing strings have been used to improve the detection distance and accuracy, the theoretical mechanism is not well understood. Based on the equivalent current model of a permanent magnet, a theoretical magnetic field model around the pre-magnetized casing string was established by using the vector potential method and vector superposition principle and validated by the COMSOL Multiphysics software. Our results show that connecting pre-magnetized individual casings with homogeneous magnetic poles can enlarge the magnetic induction intensity around the total casing string. Furthermore, the magnitude close to the casing coupling is significantly larger than that close to the middle of the individual casing. Connecting pre-mag... [more]

In grouting support projects, due to the small concealment of micro-fractures, the support effect often fails to meet design requirements. The percolation effect is a common factor that causes grouting failure, and the influence of grouting pressure on the percolation effect is very obvious. In this article, a design of a micro-fracture grouting experimental system is presented that can realize high-pressure grouting and then uses a variety of ultrafine cements to carry out high- and low-pressure grouting tests under different fracture opening conditions, thereby obtaining the grouting pressure and accumulated grouting weight during the grouting process. The results show that a combination of the grouting pressure curve and the cumulative grouting weight curve can determine whether the ultrafine cement will have a percolation effect. Increasing the grouting pressure can reduce the critical fracture opening value and also reduce the occurrence of the percolation effect. The research res... [more]

This paper presents a thorough review of state-of-the-art research and literature in the field of photovoltaic tracking systems for the production of electrical energy. A review of the literature is performed mainly for the field of solar photovoltaic tracking systems, which gives this paper the necessary foundation. Solar systems can be roughly divided into three fields: the generation of thermal energy (solar collectors), the generation of electrical energy (photovoltaic systems), and the generation of electrical energy/thermal energy (hybrid systems). The development of photovoltaic systems began in the mid-19th century, followed shortly by research in the field of tracking systems. With the development of tracking systems, different types of tracking systems, drives, designs, and tracking strategies were also defined. This paper presents a comprehensive overview of photovoltaic tracking systems, as well as the latest studies that have been done in recent years. The review will be s... [more]

The operation of microgrids is a complex task because it involves several stakeholders and controlling a large number of different active and intelligent resources or devices. Management functions, such as frequency control or islanding, are defined in the microgrid concept, but depending on the application, some functions may not be needed. In order to analyze the required functions for network operation and visualize the interactions between the actors operating a particular microgrid, a comprehensive use case analysis is needed. This paper presents the use case modelling method applied for microgrid management from an abstract or concept level to a more practical level. By utilizing case studies, the potential entities can be detected where the development or improvement of practical solutions is necessary. The use case analysis has been conducted from top-down until test use cases by real-time simulation models. Test use cases are applied to a real distribution network model, Sundo... [more]

The series resonant DC-DC converter (SRC) can regulate the input voltage in a wide range at a fixed switching frequency. In this work, the bridgeless rectifier, which is utilized intensively in the applications of the power factor correction, has been integrated into the SRC as a voltage step-up cell at the output-side of the SRC. It is shown that the conventional overlapping pulse-width modulation (PWM) of the two metal oxide semiconductor field-effect transistors MOSFETs in this rectification cell limits the input voltage regulation range of the converter due to excessive power losses in abnormal operating conditions. The abnormal operating conditions occur when the instantaneous voltage across the resonant capacitor is larger than the secondary voltage of the isolation transformer. This happens at high values of the DC voltage gain, i.e., low input voltages and high currents, which causes the resonant current to flow in the reverse direction in the same half-cycle through a parasiti... [more]

The Canadian off-grid communities heavily rely on fossil fuels. This unsustainable energetic framework needs to change, and deep geothermal energy can play an important role. However, limited data availability is one of the challenges to face when evaluating such resources in remote areas. Thus, a first-order assessment of the geothermal energy source is, therefore, needed to trigger interest for further development in northern communities. This is the scope of the present work. Shallow subsurface data and outcrop samples treated as subsurface analogs were used to infer the deep geothermal potential beneath the community of Kuujjuaq (Nunavik, Canada). 2D heat conduction models with time-varying upper boundary condition reproducing climate events were used to simulate the subsurface temperature distribution. The available thermal energy was inferred with the volume method. Monte Carlo-based sensitivity analyses were carried out to determine the main geological and technical uncertaintie... [more]

In high-pressure hydrogen systems, the check valve is one of the most easy-to-damage components. Generally, the high-pressure hydrogen flow can generate a strong impact on the check valve, which can cause damage and failure. Therefore, it is useful to study the transient flow characteristics of the high-pressure hydrogen flow in check valves. Using dynamic mesh generation and the National Institute of Standards and Technology (NIST) real hydrogen gas model, a transient-flow model of the high-pressure hydrogen for the check valve is established. First, the flow properties of high-pressure hydrogen during the opening process is investigated, and velocity changes and pressure distribution of hydrogen gas flow are studied. In addition, the fluid force, acceleration, and velocity of the valve spool are analyzed quantitatively. Subsequently, the effect of the hydrogen inlet-pressure on the movement characteristic of the valve spool is investigated. The results of this study can improve both... [more]

Based on the national level data on energy consumption by final consumption sectors (agricultural, industrial, construction, residential and transport), the present study is aimed at estimating the energy consumption at county level. The overall energy Romania has consumed throughout a year has been broken down into ‘demographic’ and ‘economic’ components. The changes in the two components were determined on an annual basis for the following reference years: 1995, 2000, 2005, 2010 and 2015. The variables used in the current investigation were assembled into two groups of indicators: demographic (urban population, population size, proportion of the population aged 65 years and over, the economically active population divided according to activities of national economy: agriculture, industry, transport), and economic (GDP per capita, energy consumption by the activities of the national economy: agriculture, residential, industry, transport). In some cases, where a significant share of th... [more]

The lack of electricity access is increasingly concentrated in rural areas of developing countries, in which mini-grids are often a suitable solution; however, given the high risks, it is crucial to minimize costs. This paper aims at analyzing existing methodologies for the optimal design of mini-grids combined with different operating strategies. Typical system operations, like the load-following (LFS) and cycle charging (CCS) strategies, are compared with the more demanding predictive strategies based on Mixed-Integer Linear Programming (MILP). The problem is formulated and solved with Particle Swarm Optimization (PSO), so to simulate traditional and predictive operating strategies. Two reformulations based on the proposed Search Space Update are also detailed and compared with the so-called one-shot MILP model, which is able to con-jointly optimize both the design and the operation of the system, in order to reduce computational requirements with the predictive strategy. The results... [more]

Global warming is intensifying worldwide, and urban heat islands are occurring as urbanization progresses. The cool roof method is one alternative for reducing the urban heat island phenomenon and lowering the heat on building roofs for a comfortable indoor environment. In this study, a cool roof evaluation was performed using an unmanned aerial vehicle (UAV) and a red, green and blue (RGB) camera instead of a laser thermometer and a thermal infrared sensor to evaluate existing cool roofs. When using a UAV, an RGB sensor is used instead of expensive infrared sensor. Various color space techniques, namely light-reflectance value, hue saturation value (HSV), hue saturation lightness, and YUV (luma component (Y) and two chrominance components, called U (blue projection) and V (red projection)) derived from RGB images, are applied to evaluate color space techniques suitable for cool roof evaluation. This case study shows the following quantitative results: among various color space techniq... [more]

An advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion of biomass or any other solids waste. Highly preheated air and steam gas (heated up to 1600 °C) was used as an oxidizing or gasification agent (feed gas). Preheated feed gas also enhances the thermal decomposition of the gasification solids for fuel gas. However, the main objective of this work is to promote new and advanced technology for the thermochemical conversion of biomass for alternative energy production. Selected results from experimental and numerical studies are also presented.

The integration of thermal energy storage systems (TES) in waste-heat recovery applications shows great potential for energy efficiency improvement. In this study, a 2D mathematical model is formulated to analyze the performance of a two-tank thermochemical heat storage system using metal hydrides pair (Mg2Ni/LaNi5), for high-temperature waste heat recovery. Moreover, the system integrates a phase change material (PCM) to store and restore the heat of reaction of LaNi5. The effects of key properties of the PCM on the dynamics of the heat storage system were analyzed. Then, the TES was optimized using a genetic algorithm-based multi-objective optimization tool (NSGA-II), to maximize the power density, the energy density and storage efficiency simultaneously. The results indicate that the melting point Tm and the effective thermal conductivity of the PCM greatly affect the energy storage density and power output. For the range of melting point Tm = 30−50 °C used in this study, it was sho... [more]

Following a recycling or continuous recycling process, there is always waste with no material or market value that can be converted into energy or other fossil fuel substitutes. The present study aimed to evaluate the management of organic waste policy and to predict the trend of organic waste generation in Albania. The research used an appropriate Box−Jenkins Auto Regressive Integrated Moving Average (ARIMA) to determine the quantification of organic waste to be generated. The main results obtained can support the decision-making process in the planning, change and short-term implementation of organic waste management, and the information provided is very useful in collecting, transporting, storing and managing waste in Albanian cities (Tirana, Durrës, Kukës, Berat, Shkodra, Dibër, Gjirokastër and Elbasan). Furthermore, the high percentage of the organic waste generation until 2025 constitutes good premises to raising public awareness related to their energy recovery.

Efforts to understand the influence of historical climate change, at global and regional levels, have been increasing over the past decade. In particular, the estimates of air temperatures have been considered as a key factor in climate impact studies on agricultural, ecological, environmental, and industrial sectors. Accurate temperature prediction helps to safeguard life and property, playing an important role in planning activities for the government, industry, and the public. The primary aim of this study is to review the different machine learning strategies for temperature forecasting, available in the literature, presenting their advantages and disadvantages and identifying research gaps. This survey shows that Machine Learning techniques can help to accurately predict temperatures based on a set of input features, which can include the previous values of temperature, relative humidity, solar radiation, rain and wind speed measurements, among others. The review reveals that Deep... [more]

Tracking performance and stability play a major role in observer design for speed estimation purpose in motor drives used in vehicles. It is all the more prevalent at lower speed ranges. There was a need to have a tradeoff between these parameters ensuring the speed bandwidth remains as wide as possible. This work demonstrates an improved static and dynamic performance of a sliding mode state observer used for speed sensorless 3 phase induction motor drive employed in electric vehicles (EVs). The estimated torque is treated as a model disturbance and integrated into the state observer while the error is constrained in the sliding hyperplane. Two state observers with different disturbance handling mechanisms have been designed. Depending on, how they reject disturbances, based on their structure, their performance is studied and analyzed with respect to speed bandwidth, tracking and disturbance handling capability. The proposed observer with superior disturbance handling capabilities is... [more]

Uranium is one of the strategic minerals used mainly in energetics. The main purpose of uranium mining is to achieve maximum production to meet the rapidly growing demand for energies. It needs to become aware that technological progress in mining processes could significantly reduce the negative impacts associated with environmental, economic, and social risks. Uranium mining is one of the most controversial topics. It is dealt with by many experts and scientists around the world. Various methods and technologies of uranium mining are encountered in professional journals, as well as political or socio-economic decisions based on the impact and importance of the energy potential of uranium deposits, or the environmental impacts of uranium mining. The deposit of Kuriskova is one of the most perspective deposits not only in Slovakia but also in the world. The deposit is located near the town of Kosice (with near 240,000 inhabitants) and near the recreational area of Jahodna in the east o... [more]

Recently, a lot of interesting research has been conducted to solve the fault current problem of the DC system. In long-distance transmission, DC transmission is more economical than AC transmission. The connection of power grids with a DC system can also better control the power flow and provide high stability. However, the control of the fault current in a DC system is more difficult to handle than in an AC system because the DC system does not make a zero point, unlike the AC system. In addition, there is a disadvantage, in that an arc occurs when a circuit breaker operates. In this paper, a new type of DC superconducting fault current limiter (SFCL) is proposed. This new type of SFCL is composed of two superconducting elements, a current limiting resistor/reactor (CLR), and a transformer. With the proposed SFCL, the DC fault current limiting experiments were performed and the DC fault current limiting characteristics of this SFCL due to the component of the CLR were analyzed.