Coaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating field and armature is presented. The design process was composed of three main steps: analytical calculation, FEM simulation and prototype experimental measurements. The key aspect in the prototype development was the mechanical construction of two rotating components of the generator. Sturdy construction was achieved using two points of contact between both rotors via the placement of the bearing between the inner and outer rotor. The experimental analysis of the prototype generator has been conducted in the laboratory at the dynamometer test stand equipped wit... [more]

This study presents an economical conditioning method for polymer electrolyte membrane (PEM) fuel cells through a parametric study investigating the factors affecting online conditioning methods. First, we compared the operating conditions between constant current (CC) mode and constant voltage (CV) mode conditioning to understand the effects of current and potential differences on conditioning. We found that CV mode conditioning is at least one hour faster at the same load. This is because unlike CV mode conditioning, which has a constant load over the entire range of the membrane electrode assembly (MEA), CC mode conditioning features current flow through the existing passage of the pre-activated triple phase boundary of the MEA so that the electronic load is not entirely used in the conditioning process. Second, the optimization of CV mode conditioning was conducted by controlling the conditioning temperature. Lastly, the economics of the proposed method were analyzed by comparing i... [more]

The deployment of microgrids could be fostered by control systems that do not require very complex modelling, calibration, prediction and/or optimisation processes. This paper explores the application of Reinforcement Learning (RL) techniques for the operation of a microgrid. The implemented Deep Q-Network (DQN) can learn an optimal policy for the operation of the elements of an isolated microgrid, based on the interaction agent-environment when particular operation actions are taken in the microgrid components. In order to facilitate the scaling-up of this solution, the algorithm relies exclusively on historical data from past events, and therefore it does not require forecasts of the demand or the renewable generation. The objective is to minimise the cost of operating the microgrid, including the penalty of non-served power. This paper analyses the effect of considering different definitions for the state of the system by expanding the set of variables that define it. The obtained r... [more]

The conformation of a ceramic piece follows the steps of preparing the raw material, molding, lamination, drying, and firing. Drying is a thermodynamic process of heat and mass transfer, with dimensional variations of the product that requires a large amount of energy. Ceramic materials when exposed to non-uniform drying may suffer cracks and deformations, reducing their post-drying quality. Thus, this work aimed to study the drying of industrial ceramic blocks in an oven with forced air circulation. Experiments were carried out to characterize the clay and drying of the ceramic block at temperatures ranging from 50 °C to 100 °C. Results of the chemical, mineralogical, granulometric, differential thermal, and thermogravimetric analysis of the clay, and heating kinetics, mass loss, and dimensional variation of the industrial ceramic block are presented and analyzed in detail. It was found that the clay is basically composed of silica and alumina (≈ 80.96%), with an average particle diam... [more]

Energy communities are key elements in the energy transition at the local level as they aim to generate and distribute energy based on renewable energy technologies locally. The literature on community energy systems is dominated by the study of electricity systems. Yet, thermal energy applications cover 75% of the total energy consumption in households and small businesses. Community-driven initiatives for local generation and distribution of thermal energy, however, remain largely unaddressed in the literature. Since thermal energy communities are relatively new in the energy transition discussions, it is important to have a better understanding of thermal energy community systems and how these systems function. The starting point of this understanding is to study factors that influence the formation and continuation of thermal energy communities. To work towards this aim, an abstract agent-based model has been developed that explores four seemingly trivial factors, namely: neighborh... [more]

This paper presents the results of studies on the possibility of using lignite to produce blast furnace coke. The aim of the investigation was to evaluate the influence of lignite addition (direct addition or incorporated into briquettes) on the textural, structural and quality parameters (NSC-CRI and CSR) of blast furnace coke. It was found that the introduction of lignite in briquettes (4.5% addition) allows coke to be produced that is characterized by equally high NSC parameters as for coke obtained without lignite addition for standard top-charged operation.

We are investigating how to use urban design approaches to conduct the layout and basic design of newly-built high-rise buildings to reduce wind obstruction and create effective urban ventilation. Few studies have addressed this issue. This study analyzes the effects of high-rise building on pedestrian-level wind in downstream street canyons based on wind tunnel test results, and examines the suitability of an urban design specification. The height (H) of high-rise buildings and the airflow passage width (S) between adjacent high-rise buildings are key control factors for this issue; H/D = 3 and S/D = 1.125 are critical parameters and recommended values (D is the height of the downstream street blocks).

In this numerical study, a direct contact membrane distillation (DCMD) system has been modeled considering various angles for the membrane unit and the Reynolds number range of 500 to 2000. A two-dimensional model developed based on the Navier−Stokes, energy, and species transport equations were used. The governing equations were solved using the finite volume method (FVM). The results showed that with an increase in the Reynolds number of up to 1500, the heat transfer coefficient for all membrane angles increases, except for the inclination angle of 60°. Also, an increase in the membrane angle up to 90° causes the exit influence to diminish and the heat transfer to be augmented. Such findings revealed that the membrane inclination angle of 90° (referred to as the vertical membrane) with Reynolds number 2000 could potentially have the lowest temperature difference. Likewise, within the Reynolds numbers of 1000 and 2000, by changing the inclination angle of the membrane, temperature dif... [more]

Electric vehicles are set to be the dominant form of transportation in the near future and Lithium-based rechargeable battery packs have been widely adopted in them. Battery packs need to be constantly monitored and managed in order to maintain the safety, efficiency and reliability of the overall electric vehicle system. A battery management system consists of a battery fuel gauge, optimal charging algorithm, and cell/thermal balancing circuitry. It uses three non-invasive measurements from the battery, voltage, current and temperature, in order to estimate crucial states and parameters of the battery system, such as battery impedance, battery capacity, state of charge, state of health, power fade, and remaining useful life. These estimates are important for the proper functioning of optimal charging algorithms, charge and thermal balancing strategies, and battery safety mechanisms. Approach to robust battery management consists of accurate characterization, robust estimation of batte... [more]

Coal gasification has been promoted as a sophisticated clean energy technology alternative to coal burning these days. Aside from the usual technical difficulties, economic issues of such projects—especially valuation challenges—are important problems that practitioners usually struggle with. This is because of the major extent of managerial flexibility linked with specific characteristics of coal gasification projects, in particular, possibilities to mothball/restart manufacturing lines, or change between different outputs. The value of such flexibilities may be well assessed by real options valuations. The aim of this paper is to show that for the coal gasification technologies the real options valuation is more suitable than traditional discounted cash flow technique. This approach was applied to calculate an integrated plant that can produce either electricity or methanol. As the valuation approach the multiplicative stochastic process was used. As a consequence, binomial lattices... [more]

This study examined the use of waste plastic oil (WPO) combined with biodiesel as an alternative fuel for diesel engines, also commonly known as compression ignition engines, and focused on comparison of the basic physical and chemical properties of fuels, engine performance, combustion characteristics, and exhaust emissions. A preliminary study was conducted to determine the suitable ratio for the fuel blends in consideration of fuel lubricity and viscosity, and these results indicated that 10% biodiesel—derived from either palm oil or castor oil—in waste plastic oil was optimal. In addition, characterization of the basic properties of these fuel blends revealed that they had higher density and specific gravity and a lower flash point than diesel fuel, while the fuel heating value, viscosity, and cetane index were similar. The fuel blends, comprised of waste plastic oil with either 10% palm oil biodiesel (WPOP10) or 10% castor oil biodiesel (WPOC10), were selected for further investig... [more]

This paper focuses on the study of proppant transport mechanisms in fractures during frac-packing operation. A multi-module, numerical proppant, reservoir and geomechanics simulator has been developed, which improves the current numerical modeling techniques for proppant transport. The modules are linked together and tailored to capture the processes and mechanisms that are significant in frac-pack operations. The proposed approach takes advantage of a robust and sophisticated numerical smeared fracture simulator and incorporates an in-house proppant transport module to calculate propped fracture dimensions and concentration distribution. In the development of software capability, the propped fracture geometry and proppant concentration, which are the output of the proppant module, are imported to the hydraulic fracture simulator through mobility modification. Complex issues of proppant transport in fractures that are addressed in the literature and captured by the current model are: h... [more]

Korea has set a goal of reducing greenhouse gas emissions (GHGEs) to levels 37% below the “business as usual (BAU)” level by 2030, and the building sector, in particular, aims to reduce GHGEs by 45,000,000-ton CO2-eq by 2020. In order to reach this goal, it is crucial to reduce GHGEs that result from energy consumption in apartment buildings, which account for approximately 65% of all buildings in the capital region where the population is concentrated. Moreover, as apartment buildings not only have high window-to wall area ratios, but also use insulating glazing (IG) with low thermal performance, an advanced window system with low heat transmittance (U-value), such as a concrete structure, is necessary for effective GHGE reduction. Therefore, this study aims to evaluate the GHGE reduction effects from replacing existing IG vacuum insulating glazing (VIG) with low U-values in the apartment housing located in the capital region. The analysis revealed the possibility of a GHGE reduction... [more]

Background: The aim of our study was to identify an optimal heating system for the analyzed church. We also evaluated the energy consumption of the existing system and of those proposed in order to choose the best heating system. Methods: We analyzed the current existing heating system, a mixed system (static heaters and hot air heating) in a Romanian heritage church, build in the 16th century, and we compared it with an underfloor heating system that has been mentioned in the literature as an alternative for church heating. We used a computational fluid dynamics (CFD) analysis of the indoor climate with two turbulence models (k-ε and k-ω). Results: Comparing the two heating systems through boxplot graphs, we could highlight pertinent conclusions regarding the temperatures and velocities of the measured air currents. Thus, of all the heating systems, the underfloor heating had the lowest temperatures, but the highest air velocities, in the churchgoers area, especially under the towers... [more]

Cheese whey (CW) and hemp hurds (HH) represent typically overabundant biowastes of food and agricultural production, and their circular management is crucial to improve both sustainability and profitability of the agri-food chain. By combining experimental biochemical methane potential (BMP) tests and literature data, the techno-economic aspects of a possible future bioenergy valorization of CW and HH through anaerobic digestion (AD) and co- digestion (coAD) were analyzed. Along the 42-days, BMP assays, CW, and HH alone rendered BMP values of 446 ± 66 and 242 ± 13 mL CH4·g VS−1, respectively. The application of coAD with CW and HH at a 70:30 ratio allowed to enhance the biomethane production by 10.7%, as compared to the corresponding calculated value. In terms of economic profitability, the valorization of HH as biomethane in a dual-purpose hemp cultivation could potentially enable net profits of up to 3929 €·ha−1, which could rise to 6124 €·ha−1 in case of coAD with CW. Finally, by pr... [more]

In the European Union, about 40% of energy consumption and 36% of CO2 emissions come from buildings; therefore, the improvement of their energy performance is a strongly focused issue. In particular, the energy efficiency of the building envelope is a very important element to pay attention to. Many studies have been conducted on this field of research, and the study illustrated in this paper also belongs to this topic. In particular, this article presents a multidisciplinary method to find sustainable solutions for energy efficiency in Italian climatic contexts using the Life Cycle Cost Analysis approach. In detail, this paper defines the reference scenario and then deepens the methodology used to determine the economically optimal thickness of a specific insulating material—hemp fiber—applied to a specific type of wall—uninsulated cavity walls made of hollow bricks, which are very widespread in Italy. The analysis is developed in relation to three different regions—Piedmont, Abruzzo,... [more]

Optimization design of an impeller is critical for the energy performance of a fan. This paper takes the promotion of fan efficiency and pressure rise as the optimization objectives to carry out multiparameter and multiobjective optimization research. Firstly, an experimental test bench is built to measure the energy performance of the original fan and verify the accuracy of the numerical method. Then, the hub outlet angle of impeller β1, the impeller outlet angle increment Δβ1, the wrap angle φ, the hub outlet angle of diffuser β2, and the diffuser outlet angle increment Δβ2 are set as the optimal parameters to conduct orthogonal optimal design. The results show that the efficiency of the optimal fan increases by 11.71%, and the pressure rise increases by 50.15%. The pressure and velocity distributions in an optimal fan are uniform, the internal flow separation is weakened, and the influence of tip leakage flow is reduced, which makes for the improvement of energy performance for the... [more]

Capacity markets (CM) are energy markets created to ensure energy supply security. Energy storage devices provide services in the CMs. Li-ion batteries are a popular type of energy storage device used in CMs. The battery lifetime is a key factor in determining the economic viability of Li-ion batteries, and current approaches for estimating this are limited. This paper explores the potential of a lithium-ion battery to provide CM services with four de-rating factors (0.5 h, 1 h, 2 h, and 4 h). During the CM contract, the battery experiences both calendar and cycle degradation, which reduces the overall profit. Physics-based battery and degradation models are used to quantify the degradation costs for batteries in the CM to enhance the previous research results. The degradation model quantifies capacity losses related to the solid−electrolyte interphase (SEI) layer, active material loss, and SEI crack growth. The results show that the physics-based degradation model can accurately predi... [more]

To better protect the ecological environment during large scale underground coal mining operations in the northwest of China, the authors have proposed a water-conservation coal mining (WCCM) method. This case study demonstrated the successful application of WCCM in the Yu-Shen mining area. Firstly, by using the analytic hierarchy process (AHP), the influencing factors of WCCM were identified and the identification model with a multilevel structure was developed, to determine the weight of each influencing factor. Based on this, the five maps: overburden thickness contour, stratigraphic structure map, water-rich zoning map of aquifers, aquiclude thickness contour and coal seam thickness contour, were analyzed and determined. This formed the basis for studying WCCM in the mining area. Using the geological conditions of the Yu-Shen mining area, the features of caved zone, water conductive fractured zone (WCFZ) and protective zone were studied. The equations for calculating the height of... [more]

In this study, the feasibility of hydrogen and methane production from grass and leaves via hyperthermophilic anaerobic digestion was investigated. The hyperthermophilic treatment of grass at 70 °C resulted in the highest concentrations of volatile fatty acids (TVFA) and reducing sugars in the supernatant of over 21 and 6.5 g/L reported on day 3 and 4 of the experiment. In contrast, hydrolysis and acidification of leaves performed slower and with lower efficiency, as the peak concentrations of TVFA and reducing sugars were observed at the end of the process. However, the highest cumulative hydrogen and methane yields of 69.64 mLH2/gVS and 38.63 mLCH4/gVS were reported for leaves digested at 70 °C, whereas the corresponding maximum productions observed for grass were 50 mLH2/gVS and 1.98 mLCH4/gVS, respectively. A temperature increase to 80 °C hampered hydrogen and methane production and also resulted in lower yields of volatile fatty acids, reducing sugars and ammonia as compared to th... [more]

With the deterioration of the environment and the depletion of fossil fuel energy, renewable energy has attracted worldwide attention because of its continuous availability from nature. Despite this continuous availability, the uncertainty of intermittent power is a problem for grid dispatching. This paper reports on a study of the scheduling and optimization of microgrid systems for photovoltaic (PV) power and electric vehicles (EVs). We propose a mathematical model to address the uncertainty of PV output and EV charging behavior, and model scheduling optimization that minimizes the economic and environmental cost of a microgrid system. A semi-infinite dual optimization model is then used to deal with the uncertain variables, which can be solved with a robust optimization algorithm. A numerical case study shows that the security and stability of the solution obtained by robust optimization outperformed that of stochastic optimization.

Voltage profile is one of many aspects that affect power quality in low-voltage distribution feeders. Weak grids have a typically high line impedance which results in remarkable voltage drops. Distribution grids generally have a high R/X ratio, which makes voltage regulation with reactive power compensation less effective than in high-voltage grids. Moreover, these networks are more susceptible to unbalance and harmonic voltage disturbances. This paper proposes an enhanced coordinated control of active and reactive power injected in a distribution grid for voltage regulation. Voltage drop mitigation was evaluated with power injection based on local features, such loads and disturbances of each connection. In order to ensure disturbances rejection like harmonic components in the grid voltages, a repetitive vector-control scheme was used. The injection of coordinated active and reactive power with the proposed control algorithm was verified through simulations and experiments, demonstrat... [more]

Recently, eco-friendly energy conversion policies have been being promoted through de-nuclearization and de-coal. For this purpose, a super grid should be built to optimize sustainable renewable energy resources such as solar and wind power. Accordingly, considering the various problems such as technology and cost, a system for efficient energy transmission is required. Hence, research is being actively conducted to apply it, owing to the development of the high voltage direct current (HVDC) system. Among HVDC systems, the cable system is extremely important, in addition to the measurement of the dielectric breakdown strength, space charge, and volume resistivity of insulating materials. The existing resistivity measurement method measures both the volume and surface resistivity using a three-terminal electrode that is used in the international standards of American Society for Testing and Materials (ASTM) D 257 and International Electrotechnical Commission (IEC) 60093. However, the ci... [more]

A multi-input-port bidirectional DC/DC converter is proposed in this paper for the energy storage systems in DC microgrid. The converter can connect various energy storage batteries to the DC bus at the same time. The proposed converter also has the advantages of low switch voltage stress and high voltage conversion gain. The working principle and performance characteristics of the converter were analyzed in detail, and a 200 W, two-input-port experimental prototype was built. The experimental results are consistent with the theoretical analysis.

Adapting historic buildings to new, modern forms generates not only financial benefits for developers but can also allow them to survive for future generations through proper remodelling. The variety of decision criteria related to the selection of a new function of a historic building makes this problem multidimensional. Many of these criteria are interrelated and have a non-linear nature which requires a comprehensive network-based rather than a classic hierarchical approach to conducting multi-criteria analysis. A comprehensive approach taking into account the specificity of the analysed problem was proposed. The study was supported by an example of the choice of building function as part of the adaptive reuse of a historic building located in Zakopane. The following variants have been analysed: a hostel (existing state), a five-star hotel, a folk art gallery and a conference and training centre. The final rating of alternatives indicates that the hotel best meets the adopted decisi... [more]