Huaneng Rudong 300 MW offshore wind farm project is located in eastern China. The wake effect is one of the major concerns for wind farm operators, as all 70 units are plotted in ranks, and the sea surface roughness is low. This paper investigated the wake intensity by combining a field test and a numerical simulation. To carry out further yaw optimization, a Gaussian wake model was adopted. Firstly, a 3D Light Detection and Ranging device (LiDAR) was used to capture the features in both horizontal and vertical directions of the wake. It indicated that Gaussian wake model can precisely predict the characteristics under time average and steady state in the wind farm. The predicted annual energy production (AEP) of the whole wind farm by the Gaussian model is compared with the calculation result of the actuator line (AL)-based LES method, and the difference between the two methods is mostly under 10%.

Due to the intermittence and randomness of the renewable energy, hybrid energy storage system is widely adopted to suppress the power fluctuation. Power distribution is crucial for the robust and efficient operation of hybrid energy system. This paper proposes an innovative framework for hybrid energy storage system power distribution combining main circuit topology, modulation method and power distribution strategy. Firstly, hybrid modulation strategy to realize power distribution in a single-phase inverter is introduced. Then, power load prediction and low frequency filter are utilized to generate references for power distribution. Finally, the simulation model is established to test the framework and the result demonstrates the superiority of the proposed framework. The mean absolute percent error of the proposed SSA-LSTM mdoel is 0.0955 and the prediciton error by 40% compared with conventional LSTM model. Additionally, the energy management framework can adjust the port power dist... [more]

The main problem with electricity supply on densely populated islands is reliable, low-carbon, and sustainable electricity. The availability of potential energy needs in-depth observation to ensure that the system can be built sustainably. This paper examines the integration of PV systems and diesel power systems on Karimunjawa Island to meet the need for reliable systems from economic, ecological, and technological aspects. Using the DigSilent Power Factory program to obtain the system response interference and penetration of the Photovoltaic (PV) system. Furthermore, this paper also tests short circuit analysis and economic feasibility analysis while validating the Levelized Cost of Electricity (LCOE) and Electric Production Cost (EPC) approaches. The results show that the availability of irradiation can handle the electricity needs on Karimunjawa Island. In addition, it proposes the designed requirements for an integrated PV power system and Diesel Power Plant (DPP) system. The rese... [more]

For the first time, the present work assesses the feasibility of using Korean red ginseng root extract, a non-ionic surfactant, for the purposes of enhanced oil recovery (EOR). The surfactant is characterized by Fourier-transform infrared spectroscopy (FT-IR) analysis. Pendant drop and sessile drop techniques are employed to study the oil−water interfacial tension (IFT) and wettability nature of the sandstone rock, respectively. In addition, oil recovery enhancement is investigated using micromodel and core floods. In the salt-free system, IFT measurements indicate that the surfactant carries a critical micelle concentration of 5 g/L. In a saline medium (up to 50 g/L), the addition of a surfactant with different concentrations leads to an IFT reduction of 47.28−84.21%. In a constant surfactant concentration, a contact angle reduction is observed in the range of 5.61−9.30°, depending on salinity rate, revealing a wettability alteration toward more water-wet. Surfactant flooding in the g... [more]

This work aims to explore and evaluate the nonreversible AC/DC five-level structure from the point of view of its operational safety: high electrical security on internal destruction and continuity in operation. It only has low-voltage monotransistor cells (Si and SiC 600 V max) and is intrinsically tolerant to imperfection control and parasites, therefore naturally secure. The design and lab-test of fault monitoring and fault diagnosis with just one voltage sensor of a single-phase five-level VIENNA rectifier were proposed. This real-time diagnostic method allows for a safe stop or corrective control strategy based on the reconfiguration of the modulation. The reconstruction strategy allows for optimization of the current and voltage signals as well as power factor. A continuous post-fault operation can be achieved for critical applications. An experimental prototype 3 kW/230 VAC/800 VDC/32 kHz was created to validate the proposed fault diagnosis method and reconfiguration control met... [more]

As the world strives to decarbonize, the effective use of renewable energy has become an important issue, and P2P power trading is expected to unlock the value of renewable energy and encourage its adoption by enabling power trading based on user needs and user assets. In this study, we constructed a bidding agent that optimizes bids based on electricity demand and generation forecasts, user preferences for renewable energy (renewable energy-oriented or economically oriented), and owned assets in a P2P electricity trading market, and automatically performs electricity trading. The agent algorithm was used to evaluate the differences in trading content between different asset holdings and preferences by performing power sharing in a real scale environment. The demonstration experiments show that: EV-owning and economy-oriented users can trade more favorably in the market with a lower average execution price than non-EV-owning users; forecasting enables economy-enhancing moves to store n... [more]

Due to the high availability of lignocellulosic biomass, which can be obtained from terrestrial plants, agricultural waste biomass, and the agro-food, paper or wood industries, its use for energy production by methane fermentation is economically and environmentally justified. However, due to their complex structures, lignocellulosic substrates have a low conversion factor to biogas. Therefore, scientists are still working on the development of new methods of the pre-treatment of lignocellulosic materials that will increase the biogas productivity from lignocellulosic biomass. The presented research focuses on the use of a pulsed electric field (PEF) to disintegrate rapeseed straw prior to the methane fermentation process. Scanning electron microscopy observation showed that, in the disintegrated sample, the extent of damage to the plant tissue was more severe than in the control sample. In the sample disintegrated for 7 min, the chemical oxygen demand increased from 4146 ± 75 mg/L to... [more]

The true bipolar modular multilevel converter-based multi-terminal direct current (MMC-MTDC) DC transmission line is prone to single-pole grounding fault, which may cause overload and overcurrent of the non-fault DC line with fault poles, resulting in system protection misoperation and system collapse. Therefore, the power transfer control strategy should be adopted to improve system stability. In addition, considering that the commutator stations of true bipolar MMC-MTDC system may have unipolar faults, it is necessary to adopt the control strategy of inter-pole power transfer or inter-station power transfer to improve the transmission capacity of the system under fault conditions. In this paper, a power transfer control strategy is proposed, which is widely applicable to MMC-MTDC system. In the case of line fault, the power transfer takes into account the line power margin and the power margin of converter station. The inter-pole power transfer is better than the inter-station power... [more]

In fusion devices, such as European Demonstration Fusion Power Reactor (EU DEMO), primary neutrons can cause material activation due to the interaction between the source particles and the targeting material. Subsequently, the reactor’s inner components become activated. For safety and safe performance purposes, it is necessary to evaluate neutron-induced activities. Activities results from divertor reflector and liner plates are presented in this work. The purpose of liner shielding plates is to protect the vacuum vessel and magnet coils from neutrons. As for reflector plates, the function is to shield the cooling components under plasma-facing components from alpha particles, thermal effects, and impurities. Plates are made of Eurofer with a 3 mm layer of tungsten, while the water is used for cooling purposes. The calculations were performed using two EU DEMO MCNP (Monte Carlo N-Particles) models with different breeding blanket configurations: helium-cooled pebble bed (HCPB) and wate... [more]

This article proposes a measurement solution designed to monitor the instantaneous frequency in power systems. It uses a data acquisition module and a GPS receiver for time stamping and traceability. A Python-based module receives data, computes the frequency, and finally transfers the measurement results to a database. The frequency is calculated with two different methods, which are compared in the article. The stored data is visualized using the Grafana platform, thus demonstrating its potential for comparing scientific data. The system as a whole constitutes an efficient, low-cost solution as a data acquisition system.

Floating wind turbine vibration controlling becomes more and more important with the increase in wind turbine size. Thus, a novel three-bifurcated mooring system is proposed for Spar-type floating wind turbines. Compared with the original mooring system using three mooring lines, three-bifurcated sub-mooring-lines are added into the novel mooring system. Specifically, each three-bifurcated sub-mooring-line is first connected to a Spar-type platform using three fairleads, then it is connected to the anchor using the main mooring line. Six fairleads are involved in the proposed mooring system, theoretically resulting in larger overturning and torsional stiffness. For further improvement, a clump mass is attached onto the main mooring lines of the proposed mooring system. The wind turbine surge, pitch, and yaw movements under regular and irregular waves are calculated to quantitatively examine the mooring system performances. A recommended configuration for the proposed mooring system is... [more]

More degrees of freedom not only enable multiphase drives to be fault-tolerant but also allow non-sinusoidal electromotive forces (NS-EMFs) in high-quality vector control. NS-EMFs lead to lower costs of design and manufacturing of electrical machines. However, the presence of multi-harmonics in NS-EMFs possibly generates pulsating torque in both healthy and faulty conditions of multiphase drives. To facilitate the use of NS-EMFs, this two-part study proposes control schemes to adaptively improve torque quality of multiphase drives in dealing with multi-harmonics of NS-EMFs. The proposed schemes are based on a simple but effective type of artificial intelligence, Adaptive Linear Neuron (Adaline). The knowledge of multiphase drives including the harmonic ranks of NS-EMFs and the rotor position is exploited to design the online-trained optimal Adalines. The first part of this study is to propose a control scheme using an Adaline for healthy mode with high-quality torque regardless of nume... [more]

Operation modes are an important topic in the research of Rotating Detonation Chamber (RDC) as it can affect the stability of RDC. However, they have not been discussed in detail due to the limitation of measurement means in experiments. The aim of this research is to investigate the mechanism of different operation modes by numerical simulation. In this paper, a numerical simulation for RDCs with separate injectors is carried out. Different operation modes and mode switching are analyzed. There is a series of reversed shock waves in the flow field. It was found that they have great effects on operation mode and mode switching in RDCs. A reversed shock wave can transit into a detonation wave after passing through isolated fresh gas region where fresh gas and burnt gas distribute alternatively. This shock-to-detonation transition (SDT) phenomenon will influence the ignition process, contra-rotating waves mode and mode switching in RDCs. SDT makes the number of detonation wave increases,... [more]

Anaerobic digestion using cigarette butts, one of most littered items, was studied not only as a waste treatment, but also as an energy production method. Methane production from cigarette butts was measured through the biochemical methane potential (BMP) test and it was evaluated whether it is possible to produce electrical energy. Intact cigarettes or individual components (filter, paper, and leaf) were supplied as the sole carbon source (substrate) for the BMP test. The tendency of methane production indicated biodegradation in the order of paper, filter, and leaves; however, the filter of cigarettes was the substrate produced the highest amount of methane per total solid. The microbial community was also analyzed in each anaerobic digestion reactor, and substrate-specific microorganisms were identified, such as Proteiniphilum strain (filter) and Methanobacterium formicicum (paper). In intact cigarettes, the related microbial community became dominant over time in the order of paper... [more]

As an environmentally friendly gas with good insulation and stable chemical properties, CF3I gas mixture is considered as a potential alternative to SF6 gas to compensate for the shortcomings of SF6 gas as a greenhouse gas. This article attempts to study the CF3I ternary gas mixtures with c-C4F8 and N2 by considering the process of streamer development in surface discharge. The model of surface discharge in CF3I gas mixture under DC voltage was established by COMSOL, and the drift-diffusion equations of particles was solved to show the discharge process, and the changes of electric field and particle concentration, etc. during the development of streamer were obtained, which provides the theoretical basis for the reliable diagnosis of partial discharge. On this basis, the model is compared with models for two other different gases (SF6/N2, artificial air) in terms of particle characteristics, streamer characteristics and streamer branches characteristics. Finally, it is concluded that... [more]

According to the forecasts made by IEA, BP, and Total in early 2021, the demand for hydrocarbons will continue for decades, and their share in the global energy balance will remain significant. Russia, as a key player in the energy market, is interested in maintaining and increasing hydrocarbon production, so further exploitation of the Arctic energy resources is an urgent issue. A large number of onshore oil and gas projects have been successfully implemented in the Arctic since the 1930s, while recently, special attention has been paid to the offshore energy resources and implementation of natural gas liquefaction projects. However, the implementation of oil and gas projects in the Arctic is characterized by a negative impact on the environment, which leads to a violation of the ecological balance in the Arctic, and affects the stability of its ecosystem, which is one of the most vulnerable ecosystems on the planet. The main goal of the present study is to understand how the implemen... [more]

The formation mechanism and propagation behaviors of a three-dimensional hydraulic fracture network in fractured shale reservoirs remain unclear, especially when the scale of hydraulic fractures is much larger than that of natural fractures. In this study, taking the well XH in the Longmaxi shale reservoir in the Sichuan Basin, China as an example, we develop a fully three-dimensional numerical model for hydraulic fracturing coupled with microseismicity based on the discrete lattice method. We introduce a randomly generated discrete fracture network into the proposed model and explore the formation mechanism of the hydraulic fracture network under the condition that the hydraulic fractures are much larger than natural fractures in scale. Moreover, microseismic events are inversely synthesized in the numerical model, which allows the evolution of the fracture network to be monitored and evaluated quantitatively. In addition, we analyze the effects of injection rate, horizontal stress di... [more]

This paper presents an open architecture for a sensor platform for the processing, collection, and image reconstruction from measurement data. This paper focuses on ultrasound tomography in block-wise-transform-reduction image reconstruction. The advantage of the presented solution, which is part of the project “Next-generation industrial tomography platform for process diagnostics and control”, is the ability to analyze spatial data and process it quickly. The developed solution includes industrial tomography, big data, smart sensors, computational intelligence algorithms, and cloud computing. Along with the measurement platform, we validate the methods that incorporate image compression into the reconstruction process, speeding up computation and simplifying the regularisation of solving the inverse tomography problem. The algorithm is based on discrete transformation. This method uses compression on each block of the image separately. According to the experiments, this solution is m... [more]

This book contains the successful submissions [...]

The paper formulates a method of active reduction of structure vibrations in the selected resonance zones of the tested object. The method ensures reduction of vibrations of the selected resonance zones by determining the parameters of the active force that meets the desired dynamic properties. The paper presents a method for determining the parameters of the active force by reducing the vibrations of the structure in its resonance zones to a given vibration amplitude. For this purpose, an analytical form was formulated, which will clearly define the dynamic properties of the tested object and the force reducing the vibrations in the form of a mathematical model. The formulated mathematical model is a modified object input function, which in its form takes into account the properties of the active force reducing the vibrations. In such a case, it is possible to use the methods of mechanical synthesis to decompose the modified characteristic function into the parameters of the system an... [more]

This paper presents a complete review of MVDC applications and their required technologies. Four main MVDC applications were investigated: rail, shipboard systems, distribution grids, and offshore collection systems. For each application, the voltage and power levels, grid structures, converter topologies, and protection and control structure were reviewed. Case studies of the varying applications as well as the literature were analyzed to ascertain the common trends and to review suggested future topologies. For rail, ship, and distribution systems, the technology and ability to implement MVDC grids is available, and there are already a number of case studies. Offshore wind collection systems, however, are yet able to be implemented. Across the four applications, the MVDC voltages ranged from 5−50 kV DC and tens of MW, with some papers suggesting an upper limit of 100 kV DC and hundreds of MV for distribution networks and offshore wind farm applications. This enables the use of varyin... [more]

Environmental protection is currently one of the key priority areas of the European Union (EU). The search for precise tools to assess the impact of the economy, industry, or the production of individual products or services is crucial for an effective and efficient policy in environmental protection. Blockchain technology, originally related to the financial sector and cryptocurrencies, is an innovative solution that is increasingly being implemented by other areas of the economy and industry sectors. The authors reviewed the literature and based on it presented the possibilities and effects of using blockchain technology in Life Cycle Assessment (LCA), which is in line with the current development trends of this method. The analysis of the research conducted in this area also allowed to present not only the advantages of blockchain in LCA, but also the limitations of this technology and the potential directions of further research.

The purpose of this work is to explore the nonlinear vibration of a rub-impact Jeffcott rotor. In the first stage, the motion is not affected by the friction force, but in the second stage, the motion is influenced by the normal force and the friction force. The governing equations of the rotor of this model are derived in this paper. In consequence, there appears a difference between the two stages. We establish an approximate analytical solution for nonlinear vibrations corresponding to two stages with the mention of the location of jumps. The obtained results are compared with the numerical integration results. The steady-state response and the stability of the solutions are analytically determined for the two stages. The stability of a full annular rub solution is studied with the help of the Routh−Hurwitz criterion. Effects of different parameters of the system, the saddle-node bifurcation (turning points) and the Hopf bifurcation are presented. The main contribution lies in the a... [more]

The increase in cement production as a result of growing demand in the construction sector means an increase in energy consumption and CO2 emissions. These emissions are estimated at 7% of the global production of CO2. Ultra-high-performance concrete (UHPC) has excellent mechanical and durability characteristics. Nevertheless, it is costly and affects the environment due to its high amount of cement, which may reach 800−1000 kg/m3. In order to reduce the cement content, silica fume (SF) was utilized as a partial alternative to cement in the production of UHPC. Nevertheless, SF is very expensive. Therefore, the researchers investigated the use of supplementary cementitious materials cheaper than SF. Very limited review investigates addressed the impact of such materials on different properties of UHPC in comparison to that of SF. Thus, this study aims to summarize the effectiveness of using some common supplementary cementitious materials, including fly ashes (FA), ground granulated bla... [more]

Hydrogen produced without carbon emissions could be a useful fuel as nations look to decarbonize their electricity, transport, and industry sectors. Using the iodine−sulfur (IS) cycle coupled with a nuclear heat source is one method for producing hydrogen without the use of fossil fuels. An economic dispatch model was developed for a nuclear-driven IS system to determine hydrogen sale prices that would make such a system profitable. The system studied is the HTTR-GT/H2, a design for power and hydrogen cogeneration at the Japan Atomic Energy Agency’s High Temperature Engineering Test Reactor. This study focuses on the development of the economic model and the role that input data plays in the final calculated values. Using a historical price duration curve shows that the levelized cost of hydrogen (LCOH) or breakeven sale price of hydrogen would need to be 98.1 JPY/m3 or greater. Synthetic time histories were also used and found the LCOH to be 67.5 JPY/m3. The price duration input was f... [more]