Due to the spread of the SARS-CoV-2 virus, most countries have tightened their public health policies. One way to limit the spread of the virus is to make mouth and nose cover compulsory in public spaces. The article presents the impact of wearing masks on the perception of thermal comfort. The following masks were analysed: FFP2, cotton, medical, PM2.5, half-face protective shield plastic and full-face protective shield plastic. The research was carried out for two scenarios of an ambient temperature: −20 and 30 °C. A thermal manikin was used for the tests. In the case of when a temperature equals 20 °C, the dry masks increase comfort, both general and local, while wet masks reduce comfort. On the other hand, at 30 °C, only wet masks do not increase discomfort. In addition, moist masks require less heat flux to achieve a certain skin temperature. However, it should be remembered that it is not advisable to wet the masks from the health point of view.

Hydrate-based technologies (HBTs) have high potential in many fields. The industrial application of HBTs is limited by the low conversion rate of the water into hydrate (RWH), and sodium lignin sulfonate (SLS) has the potential to solve the above problem. In order to make the HBTs in the presence of SLS applied in industry and promote the advances of commercial HBTs, the effect of SLS on the thermodynamic equilibrium hydrate formation pressure (Peq) was investigated for the first time, and a new model (which can predict the Peq) was proposed to quantitatively describe the thermodynamic effect of SLS on the hydrate formation. Then, the effects of pressure and initial SLS concentration on the hydrate formation rate (rR) at different stages in the process of hydrate formation were investigated for the first time to reveal the kinetic effect of SLS on hydrate formation. The experimental results show that SLS caused little negative thermodynamic effect on hydrate formation. The Peq of the e... [more]

A simplified and accurate model of a surge arrester used in the residual voltage test is proposed in this paper. With the help of a genetic algorithm, the measured impulse current and residual voltage waveforms are utilized to determine circuit parameters of the proposed model and the generation circuit precisely. The technique starts from the circuit parameter determination using the preliminary experimental data with a lower current peak than that specified by the standard. From the determined model and with the help of the genetic algorithm, the circuit parameters and the charging voltage to obtain the specified current peak and the residual voltage can be estimated accurately. The validity of the proposed technique has been verified by experiments for the estimation of the appropriate current circuit parameters, the charging voltage, and the residual voltage. In addition, the application of the proposed model in the residual voltage tests is presented. From comparison of simulated... [more]

The main means of secondary oil recovery is water flooding, which has been widely used in various oilfields. Different flow rates have a great impact on the recovery ratio and the occurrence of remaining oil. Scholars have carried out extensive research on it, but mostly on the macro scale, and research on the three-dimensional micro scale is also limited by accuracy and a lack of accurate understanding. In this paper, micro-CT and core displacement experiments are used to intuitively show the occurrence state of remaining oil under different flow rates. Through a series of quantitative image processing methods and remaining oil classification methods, the occurrence characteristics of remaining oil under different flow rates are systematically evaluated and studied. The results show that: (1) As the displacement rate increases, the remaining oil saturation decreases (61%; 35%; 23%), but the remaining oil is more evenly distributed along the slice; (2) Two lower displacement speeds (0.... [more]

This work discusses the results of a study of the influence of rates of change of confining pressure on the result of a drained compressibility tests intended to determine the modulus of compressibility of a rock skeleton Ks. A series of cyclical compressibility tests was performed on samples of sandstone soaked in kerosene, for various rates of compression and decompression of the pressure liquid filling the cell and the pore volume of the sample. The studies showed that the deformability of the tested sample was directly proportional to the rate of change of the confining pressure. As a consequence, the value of the Ks modulus and Biot coefficient α decreased with increasing sample load rate. This phenomenon should be attributed primarily to equilibration of the liquid pressure inside the high-pressure cell with the liquid pressure in the sample pore space, caused by filtration of the pore liquid. These phenomena prove that the filtration process impacts the values of the modulus of... [more]

In this study, coffee waste (CW) and empty fruit bunches (EFB) were employed as precursors for the production of activated carbons by a chemical activation method. KOH, ZnCl2, and H3PO4 were used as activating agents along with their three mixing ratios of 1:0, 1:1, 1:3, w/w, and carbonization temperatures of 600 °C, 700 °C, and 800 °C were used to prepare these activated carbons. The highest yields of produced activated carbons were observed at 600 °C with a value of 45.20% for coffee waste and 48.20% for empty fruit bunch, with a 1:3 w/w (H3PO4) ratio. However, the maximum specific surface area was 3068 m2 g−1, and 2147 m2 g−1 obtained at 800 °C for coffee waste and empty fruit bunch activated carbons, respectively. The surface features of these products exhibited acute morphological changes, as were clearly noticed via SEM studies. Moreover, in the Van Krevelen diagram, it was also observed that both the H/C and O/C ratios were dramatically decreased to 0.0019 and 0.0759, and 0.0066... [more]

As a large number of small-scale PV plants have been deployed in distribution systems, generation forecasting of such plants has recently been gaining interest. Because the PV power mainly depends on weather conditions, it is important to accurately collect weather data for relevant PV sites to enhance PV forecasting accuracy. However, small-scale PV plants do not often have their own measuring apparatus to get historical weather data, so they have used weather datasets from relatively nearby weather data centers (WDCs). Therefore, these small-scale PV plants have difficulty delivering robust and reliable forecasting accuracy because of inappropriate predicted weather data from a distance. In this paper, two weather data mixing models are proposed: (a) inverse distance weighting (IDW), and (b) inverse correlation weighting (ICW). These models acquire adequate mixed weather data for the day-ahead generation forecasting for small-scale PV plants. Furthermore, the mixed weather data are c... [more]

In this study, magnetic steel slag biochar (MSSB) was synthesized from low-cost steel slag waste to investigate the effectiveness of steel slag biochar composite for NH4-N removal and magnetic properties in aqueous solution. The maximum adsorption capacity of NH4-N by MSSB was 4.366 mg/g according to the Langmuir model. The magnetic properties of MSSB indicated paramagnetic behavior and a saturation magnetic moment of 2.30 emu/g at 2 Tesla. The NH4-N adsorption process was well characterized by the pseudo-second order kinetic model and Temkin isotherm model. This study demonstrated the potential of magnetic biochar synthesized from steel slag waste for NH4-N removal in aqueous solution.

For self-entrainment venturi nozzles, the effects of nozzle shapes and operating conditions on the water−air two-phase flow pattern, and the characteristics of the air entrainment rate have been investigated. A rectangular venturi nozzle with width and height dimensions of 3 mm and 0.5 mm was used with a vertically downward flow direction. The pressure ratio, which is the ratio of the inlet and outlet pressures, water flow rate, and diverging angle were set as experimental parameters. From the flow visualization, annular and bubbly flows were observed. In the case of bubbly flow, the more bubbles that are generated with a higher water flow rate, the smaller the pressure ratio. In the case of annular flow, the increased pressure ratio and water flow rate induce the breakup of air core in the diverging area and make the interfacial oscillation stronger, which finally causes the flow transition from annular to bubbly flow, by accompanying a sharp increase in the air entrainment rate. Duri... [more]

This paper reports the results of a study concerned with air−water and air−oil two-phase flow in channels packed with open-cell metal foams. The research was conducted in horizontal channel with an internal diameter of 0.02 m and length of 2.61 m. The analysis applied three metal foams with pore density 20, 30, and 40 PPI and porosity typical for industrial applications, changing in the range of 92−94%. The experimental data were used to develop a new method for predicting void fraction in two-phase gas−liquid flow in channels packed with metal foams. A new gas void fraction calculating method based on drift-flux model was developed. This model gives a correct representation of changes in the gas void fraction value and good prediction accuracy. The average relative error in calculating the air void fraction in two-phase flow is less than 13%, and 86% of experimental points is characterized by an error less than 20%.

The rapid growth of Central European economies has been related to inward FDI, so these countries are often regarded as dependent market economies. What is interesting in this context is the international expansion of some domestic-owned manufacturing companies from Central Europe. Looking through the lens of global production networks (GPN) and evolutionary resilience perspectives, the paper aims to identify paths and mechanisms of development of new multinational companies, namely Polish automotive firms expanding from around 2010 onwards in the global markets through acquisitions and greenfield investments in Western Europe, North America, and Asia. The authors ponder on the underlying motives and barriers of this process, the capabilities, and features of Polish-owned companies. In order to do it, both qualitative (13 interviews with representatives of new multinationals and the other stakeholders preceded by content analysis of various documents, including company annual reports i... [more]

Here, we demonstrate the fabrication of a flexible and transparent micro-supercapacitor (MSC), using colorless polyimide (CPI) via a direct laser writing carbonization (DLWC) process. The focused laser beam directly carbonizes the CPI substrate and generates a porous carbon structure on the surface of the CPI substrate. Fluorine, which is one of the chemical compositions of CPI, can enhance the specific area and the conductivity of the carbon electrode by creating micropores in carbon structures during carbonization. Thus, the fabricated carbonized CPI-based MSC shows enhanced specific capacitance (1.20 mF at 10 mV s−1) and better transmittance (44.9%) compared to the conventional PI-based MSC. Additionally, the fabricated carbonized CPI-based MSC shows excellent cyclic performance with minimal reduction (<~10%) in 3000 cycles and high capacitance retention under mechanical bending test conditions. Due to its high flexibility, transparency, and capacitance, we expect that carbonized... [more]

The occurrence of surface discontinuous deformations in post-mining areas is currently a significant and important problem, due to both the frequency of their occurrence and the threat they pose to public safety. This paper presents the results of research concerning the possibility of sinkhole formation in the areas of abandoned mining excavations. For the purpose of assessing the condition of the rock mass disturbed by the existence of numerous mining excavations, electrical resistivity tomography investigations were carried out for the selected area where mining was undertaken in the past at shallow depths and many underground workings accessing the deposit exist. The sinkhole hazard was also analysed theoretically with a new original model based on the solution of A. Sałustowicz’s pressure arch theory.

Compared with a silicon MOSFET device, the SiC MOSFET has many benefits, such as higher breakdown voltage, faster action speed and better thermal conductivity. These advantages enable the SiC MOSFET to operate at higher switching frequencies, while, as the switching frequency increases, the turn-on loss accounts for most of the loss. This characteristic severely limits the applications of the SiC MOSFET at higher switching frequencies. Accordingly, an SRD-type drive circuit for a SiC MOSFET is proposed in this paper. The proposed SRD-type drive circuit can suppress the turn-on oscillation of a non-Kelvin packaged SiC MOSFET to ensure that the SiC MOSFET can work at a faster turn-on speed with a lower turn-on loss. In this paper, the basic principle of the proposed SRD-type drive circuit is analyzed, and a double pulse platform is established. For the purpose of proof-testing the performance of the presented SRD-type drive circuit, comparisons and experimental verifications between the... [more]

The paper presents the preliminary results on the development of an integrated stripline-based microwave-microfluidic module. The measurements were performed in a frequency range from 300 MHz up to 12 GHz, with the microchannel filled with three different test fluids—deionized water, the ethanol-water solution and pure ethanol. Due to the higher-than-expected losses in transmittance, the selected module was examined with use of the cross-sections taken along its length. The possible causes were highlighted and described. Likewise, the proposed areas of further investigations have been clearly described.

Loss allocation through analytical expressions in three-core lead-sheathed armored cables is challenging due to the complex geometry of this type of cable, commonly employed in submarine energy transmission systems (involving twisted conductors, sheaths and armor). Most of the expressions of the IEC standard 60287 have not been properly adapted for three-core armored cables, leading to inaccurate values for the different losses, so important efforts are currently devoted to improving them. In this work, an improved ultra-shortened 3D finite element model (FEM) is employed for developing an in-depth analysis of the electromagnetic interactions that take place in 6 real cables, being especially focused on those aspects that are not considered in the IEC standard. As a result, important conclusions are derived regarding the losses in conductors and sheaths, which introduce different corrections for improving the accuracy of the IEC expressions. The new formulation is then employed to prop... [more]

The influence of moisture content on substrate thermal conductivity at different temperatures was investigated for four different commercially available substrates for green roofs. In the unfrozen state, as moisture content increased, thermal conductivity increased linearly. In the phase transition zone between +5 and −10 °C, as temperature decreased, thermal conductivity increased sharply during the transition from water to ice. When the substrate was frozen, thermal conductivity varied exponentially with substrate moisture content prior to freezing. Power functions were found between thermal conductivity and temperature. Two equally sized, green roof test cells were constructed and tested to compare various roof configurations including a bare roof, varying media thickness for a green roof, and vegetation. The results show that compared with the bare roof, there is a 75% reduction in the interior temperature’s amplitude for the green roof with 150 mm thick substrate. When a sedum mat... [more]

This paper presents experimental results of high-current impulse tests on six ground electrode configurations. A high impulse current generator is employed to inject different magnitudes of current into these rod electrodes, under both positive and negative impulse polarities. The effect of increasing the number of rod electrodes, hence the resistance at DC or steady-state (RDC), on the impulse response of ground electrodes is analysed. From the analysis of the results, it was found that the larger the size of rod electrodes, the less current-dependent Zimpulse becomes. The percentage of reduction of impulse impedance, Zimpulse from its steady state, and RDC values are found to be independent of impulse polarity. However, as the voltage magnitudes were increased, an occurrence of breakdown was seen, with higher breakdown voltage seen in negative impulse polarity in comparison to positive impulse polarity. Relatively, the higher the breakdown voltage is, seen in the ground electrodes su... [more]

Bayesian inference is used to calibrate a bottom-up home PLC network model with unknown loads and wires at frequencies up to 30 MHz. A network topology with over 50 parameters is calibrated using global sensitivity analysis and transitional Markov Chain Monte Carlo (TMCMC). The sensitivity-informed Bayesian inference computes Sobol indices for each network parameter and applies TMCMC to calibrate the most sensitive parameters for a given network topology. A greedy random search with TMCMC is used to refine the discrete random variables of the network. This results in a model that can accurately compute the transfer function despite noisy training data and a high dimensional parameter space. The model is able to infer some parameters of the network used to produce the training data, and accurately computes the transfer function under extrapolative scenarios.

The cumulative displacement-time curve is the most common and direct method used to predict the deformation trends of landslides and divide the deformation stages. A new method based on the inverse logistic function considering inverse distance weighting (IDW) is proposed to predict the displacement of landslides, and the quantitative standards of dividing the deformation stages and determining the critical sliding time are put forward. The proposed method is applied in some landslide cases according to the displacement monitoring data and shows that the new method is effective. Moreover, long-term displacement predictions are applied in two landslides. Finally, summarized with the application in other landslide cases, the value of displacement acceleration, 0.9 mm/day2, is suggested as the first early warning standard of sliding, and the fitting function of the acceleration rate with the volume or length of landslide can be considered the secondary critical threshold function of lands... [more]

The current electrification status in West African countries presents rural electrification rates below 40%, national grid losses above 39% with frequent disruptions, and electricity prices averaging $0.35/kWh, up to national values of $0.66/kWh. With this, off-grid systems have gained great attention during the last decade as energy solutions; especially solar home systems (SHS) and mini grids. Nowadays, 385 mini grids with a power of near 30 MW are operating in West Africa, with 95% based on PV. Since 2019, result-based tenders with international aid funding—more effective than previous competitive tenders—seek to install at least 317 new mini grids in Togo, 250 in Nigeria, 100 in Burkina Faso, and two in Mali. Besides, the market for mini-grid energy access start-ups grew from $19 million in 2013 to $339 million in 2018. Despite this recent development in West Africa, research and data for mini grids in this region is scarce, and it is mostly approached from the technological side,... [more]

In this present work, the air-conditioning test performance of an ejector refrigerator-based air-conditioner (ERAC) was proposed. The ERAC was operated as the water chiller to produce the cooling load up to 4.5 kW. The chilled water temperature was later supplied to the fan-coil unit for producing the thermal comfort condition. The cooling water used to cool the condenser was achieved from the cooling tower which was operated under the hot and humid ambient. This is to demonstrate the feasibility of using the ERAC in real working conditions. The cooling load supplied to the air-conditioned space was applied by the air heater. The ERAC could efficiently be operated to produce the thermal comfort condition which was driven by the hot water temperature (Thot) of 90−98 °C. The system performance could vary with the heat source temperatures, cooling load, primary nozzle, and air-conditioned space temperature. The optimal performance was determined when varying the Thot, and, hence, the opti... [more]

To better understand the mass transfer behaviors in CaC2 production from CaO and coke, this paper studies the diffusion behaviors of CaO and graphite, with or without ash, at 1500 and 1700 °C. CaO and graphite are pressed into tablets and heated alone or in close contact. Physical and chemical changes in these tablets are analyzed by XRD and SEM+EDX. In some experiments, thin Mo wires are placed between the closely contacted CaO and graphite tablets to identify the diffusion direction. It is found that the diffusion between CaO and low-ash graphite is very limited. SiO2 in a high-ash graphite diffuses into CaO tablet and reacts with CaO to form Ca2SiO4, which then diffuses into the graphite tablet easily and leads to CaC2 formation at 1700 °C.

The paper presents the novel use of analytical models of a beam on an elastic foundation. The one-parameter model (Winkler model) and the two-parameter models (Filonenko-Borodich and Pasternak models) were investigated. These models were used to describe the elastic response of axially loaded blind rivets used with sandwich structures. The elastic response related to the elastic strain energy is mentioned in the paper as the resilience modulus of the connection. The databases from laboratory pull-out tests were used to verify these models. One type of blind rivet (aluminum, with three clamping arms) and one type of sandwich beam were used. The sandwich beams used in the experiments consisted of two thin-walled and stiff external facings (zinc-coated steel) and a thick, soft core (polyisocyanurate foam—PIR). In the test the sandwich beams were subjected to static, axial pull-out loading. The research provides the quantitative comparison between the laboratory experiment and the analytic... [more]

An experimental investigation of single Taylor bubbles rising in stagnant and downward flowing non-Newtonian fluids was carried out in an 80 ft long inclined pipe (4°, 15°, 30°, 45° from vertical) of 6 in. inner diameter. Water and four concentrations of bentonite−water mixtures were applied as the liquid phase, with Reynolds numbers in the range 118 < Re < 105,227 in countercurrent flow conditions. The velocity and length of Taylor bubbles were determined by differential pressure measurements. The experimental results indicate that for all fluids tested, the bubble velocity increases as the inclination angle increases, and decreases as liquid viscosity increases. The length of Taylor bubbles decreases as the downward flow liquid velocity and viscosity increase. The bubble velocity was found to be independent of the bubble length. A new drift velocity correlation that incorporates inclination angle and apparent viscosity was developed, which is applicable for non-Newtonian fluids... [more]