Energy efficiency programmes (EEPs) are schemes operated by utilities or other bodies in order to incentivize energy efficiency improvement, in particular by adoption of energy-efficient products and typically by means of an economic reward. Ample experience has been gained, especially in the U.S., where EEPs have been in use for decades, with the rationale of avoiding additional energy supply by improving energy efficiency. More recently, EEPs have been implemented in Europe and in Switzerland. This review paper presents insights from the U.S., the EU and especially from Switzerland, with a focus on levelised programme cost of saved energy (LPC) as a key performance indicator. These LPC values, which take the perspective of the programme operator, are typically low to very low compared to the cost of electricity supply, thereby representing an important argument in favour of their use. The country examples show that EEPs are being effectively and successfully put into practice, for ex... [more]

This paper presents simulation and bench test results for a special type of centrifugal pump that enables the transport of dispersive foaming liquids and simultaneous separation of the liquid phase. During the design phase, CFD (Computer Fluid Dynamics) simulations were performed using Ansys Fluent. The simulations covered changing the operating parameters of the pump (mass/volume flow rate), pressure analysis for the first impeller, and structural optimization of the pump components. In the second stage of the research, the pump and a measuring station were constructed to validate the results of the numerical simulations.

The current transformation of power systems is aiming towards distributed source integration and general decentralization. Renewable energy sources and support of local energy supply create conditions for widespread use of new technologies and smart grids. As the electrical grids become more electrically independent, the importance of frequency control will rise. Stability of the system in such cases is no longer only relying on rotating inertia of generators as in the centralized grid. This known scenario has already been analyzed by many with computational models for optimal safety precautions of the grid. This paper aims to update the common home appliance frequency characteristics through measurements and compare them to those currently used. These devices were divided into two groups: general categorization and light sources. Subsequently, the frequency sensitivity coefficients were evaluated and analyzed home appliances were sorted into three categories according to the size of t... [more]

The use of static frequency converters, which have a high switching frequency, generates voltage pulses with a high rate of change over time. In combination with cable and motor impedance, this generates repetitive overvoltage at the motor terminals, influencing the occurrence of partial discharges between conductors, causing degradation of the insulation of electric motors. Understanding the effects resulting from the frequency converter−electric motor interaction is essential for developing and implementing insulation systems with characteristics that support the most diverse applications, have an operating life under economically viable conditions, and promote energy efficiency. With this objective, a search was carried out in three recognized databases. Duplicate articles were eliminated, resulting in 1069 articles, which were systematically categorized and reviewed, resulting in 481 articles discussing the causes of degradation in the insulation of electric motors powered by frequ... [more]

In the transient process of the grid-connected converter (GCC), the existing research mainly focuses on the impact of the control loops. Little attention is paid to the transient stability issues driven by the imbalance between the input power and output power of GCC. This paper shows that the transient stability issues will still exist even if ignoring the dynamics of phase-locked loop (PLL) and current loop. In this paper, the models of the AC grid and the GCC are built under the assumption that the dynamics of the PLL and current loop are ignored. Then, by analyzing the transient process of GCC under non-severe remote voltage sag, the effects of the imbalance power on the transient stability of GCC are discussed. Moreover, for the GCC to operate stably after the transient process, there should be a maximum input power limit (MIPL) for GCC, and the imbalance power equation is applied in this paper to determine the transient stability of GCC. Furthermore, the effects of the current li... [more]

In an interior permanent magnet synchronous motor, an adhesive such as bond is generally injected into the magnet tolerance to prevent vibration of the permanent magnet within the insertion space. In this case, a disadvantage is that the magnet tolerance does not contribute to the performance. In this paper, ferrofluid is inserted to improve the torque density, utilizing the magnet tolerance. When inserting ferrofluid into the magnet tolerance, it is important to fix the magnet because conventional adhesives are not used, and it is important that the ferrofluid does not act as a leakage path within the insertion space. In this study, a new rotor configuration using a plastic barrier that satisfies these considerations was introduced. The analysis was conducted through finite element analysis (FEA), and this technique was verified by comparing the simulation results and the experimental results through a dynamo test. It was confirmed that the no-load back electromotive force in the fina... [more]

The coordinate transformation method of asymmetric dual three phase synchronous motor (ADTP-SM) is a Double dq transform using two dq-axes and a vector space decomposition (VSD) model method using the orthogonality of ADTP-SM. There are several studies comparing the two methods in a healthy state, but few in a single-phase open fault state. In the healthy, when the VSD model is applied, different harmonic orders of the phase current are projected onto the dq and xy-axes (the axis for controlling harmonics of the phase current), and the two-axes are orthogonal, so it can be controlled stably. In the single-phase open fault state, the same current control logic as in the healthy situation is applied. When applying the Double dq transform, the dq-axis of the fault set fluctuates, and it affects the healthy set, so it cannot be controlled stably. When applying the VSD model, if both the dq-axis and the xy-axis are controlled, the two coordinate systems do not have orthogonality and cannot... [more]

The objective of the present study is to predict how changes in the fracture treatment design parameters will affect the production performance of new gas wells in a target zone of the Marcellus shale. A recently developed analytical flow-cell model can estimate future production for new wells with different completion designs. The flow-cell model predictions were benchmarked using historic data of 11 wells and 6 different completion designs. First, a type well was generated and used with the flow-cell model to predict the performance of the later infill wells—with variable completion designs—based off the performance of earlier wells. The flow-cell model takes into account known hyperbolic forecast parameters (qi, Di, and b-factor) and fracture parameters (height, half-length, and spacing) of a type well. Next, the flow-cell model generates the hyperbolic decline parameters for an offset well based on the selected changes in the fracture treatment design parameters. Using a numerical... [more]

As most of the light and easy oil fields have been produced or are nearing their end-life, the emulsion stability is enhanced and water cut is increasing in produced fluid which have brought challenges to oil−water separation in onshore and offshore production trains. The conventional solution to these challenges includes a combination of higher chemical dosages, larger vessels and more separation stages, which often demands increased energy consumption, higher operating costs and larger space for the production facility. It is not always feasible to address the issues by conventional means, especially for the separation process on offshore platforms. Electrostatic coalescence is an effective method to achieve demulsification and accelerate the oil−water separation process. In this paper, a novel compact electrostatic coalescer with helical electrodes was developed and its performance on treatment of water-in-oil emulsions was investigated by experiments. Focused beam reflectance measu... [more]

With widespread applications for lithium-ion batteries in energy storage systems, the performance degradation of the battery attracts more and more attention. Understanding the battery’s long-term aging characteristics is essential for the extension of the service lifetime of the battery and the safe operation of the system. In this paper, lithium iron phosphate (LiFePO4) batteries were subjected to long-term (i.e., 27−43 months) calendar aging under consideration of three stress factors (i.e., time, temperature and state-of-charge (SOC) level) impact. By means of capacity measurements and resistance calculation, the battery’s long-term degradation behaviors were tracked over time. Battery aging models were established by a simple but accurate two-step nonlinear regression approach. Based on the established model, the effect of the aging temperature and SOC level on the long-term capacity fade and internal resistance increase of the battery is analyzed. Furthermore, the storage life of... [more]

Wave energy is nowadays one of the most promising renewable energy sources; however, wave energy technology has not reached the fully-commercial stage, yet. One key aspect to achieve this goal is to identify an effective control strategy for each selected Wave Energy Converter (WEC), in order to extract the maximum energy from the waves, while respecting the physical constraints of the device. Model Predictive Control (MPC) can inherently satisfy these requirements. Generally, MPC is formulated as a quadratic programming problem with linear constraints (e.g., on position, speed and Power Take-Off (PTO) force). Since, in the most general case, this control technique requires bidirectional power flow between the PTO system and the grid, it has similar characteristics as reactive control. This means that, under some operating conditions, the energy losses may be equivalent, or even larger, than the energy yielded. As many WECs are designed to only allow unidirectional power flow, it is ne... [more]

This paper presents a technical, economic, and environmental analysis and optimization of the impact of the reduction of diesel fuel subsidy in the design of an off-grid hybrid power system (OHPS). The OHPS includes a diesel generator, battery energy storage system (BESS), and a solar power system (SPS). This impact will focus on the electricity production levels of each of the OHPS components according to the increase of the fuel price and the SPS size. The Bellavista community in Ecuador was selected as the case study for this work. In this South American country, the government has begun a gradual increase in the diesel fuel price until it reaches international prices. Fifteen scenarios of OHPSs were simulated, in Homer Pro software, considering three SPS sizes and varying the diesel fuel price in five values. The annual load profile for the simulations was built based on the information of a previous study in this community. The results showed that for lower fuel prices (USD$0.26/L... [more]

Computational fluid dynamics (CFD) modeling of an entrained-flow reactor is demonstrated and compared with experimental data. The study is focused on char conversion modeling and its impact on gasification simulation results. An innovative procedure of optimizing input data to empirical char conversion kinetic-diffusion model is investigated, based on the complex carbon burnout kinetic model for oxidation (CBK/E) and gasification (CBK/G). The kinetics of the CBK/G model is determined using the data from char gasification experiments in a drop tube reactor. CFD simulations are performed for the laboratory-scale entrained-flow reactor at Brigham Young University for the bituminous coal. A substantial impact of applied kinetic parameters on the in-reactor gas composition and char conversion factor was observed. The effect was most considerable for the reduction zone, where gasification reactions dominate, although a non-negligible impact could also be observed in the flame zone. Based on... [more]

Wind power is cleaner and less expensive compared to other alternative sources, and it has therefore become one of the most important energy sources worldwide. However, challenges related to the operation and maintenance of wind farms significantly contribute to the increase in their overall costs, and, therefore, it is necessary to monitor the condition of each wind turbine on the farm and identify the different states of alarm. Common alarms are raised based on data acquired by a supervisory control and data acquisition (SCADA) system; however, this system generates a large number of false positive alerts, which must be handled to minimize inspection costs and perform preventive maintenance before actual critical or catastrophic failures occur. To this end, a fault detection methodology is proposed in this paper; in the proposed method, different data analysis and data processing techniques are applied to real SCADA data (imbalanced data) for improving the detection of alarms related... [more]

This article presents a multiple-vector finite-control-set model predictive control (MV-FCS-MPC) scheme with fuzzy logic for permanent-magnet synchronous motors (PMSMs) used in electric drive systems. The proposed technique is based on discrete space vector modulation (DSVM). The converter’s real voltage vectors are utilized along with new virtual voltage vectors to form switching sequences for each sampling period in order to improve the steady-state performance. Furthermore, to obtain the reference voltage vector (VV) directly from the reference current and to reduce the calculation load of the proposed MV-FCS-MPC technique, a deadbeat function (DB) is added. Subsequently, the best real or virtual voltage vector to be applied in the next sampling instant is selected based on a certain cost function. Moreover, a fuzzy logic controller is employed in the outer loop for controlling the speed of the rotor. Accordingly, the dynamic response of the speed is improved and the difficulty of t... [more]

Battery systems bring technical and economic advantages to electrical distribution systems (EDSs), as they conveniently store the surplus of cheap renewable generation for use at a more convenient time and contribute to peak shaving. Due to the high cost of batteries, technical and economic studies are needed to evaluate their correct allocation within the EDS. To contribute to this analysis, this paper proposes a stochastic mathematical model for the optimal battery allocation (OBA), which can be guided by the optimization of two different economic metrics: net present value (NPV) and internal rate of return (IRR). The effects of the OBA in the EDS are evaluated considering the stochastic variation of photovoltaic generation and load. Tests with the 33-node IEEE test system indicate that OBA results in voltage profile improvement (~1% at peak time), peak reduction (31.17%), increased photovoltaic hosting capacity (18.8%), and cost reduction (3.06%). Furthermore, it was found that the... [more]

Acoustic resonance in closed side branches should be enhanced to improve the efficiency of wind energy harvesting equipment or thermo-acoustic engine. However, in gas pipeline transportation systems, this kind of acoustic resonance should be suppressed to avoid fatigue damage to the pipeline. Realizable k-ε delayed detached eddy simulations (DDES) were conducted to study the effect of different branch pipe shapes on acoustic resonance. At some flow velocities, the pressure amplitude of the simulation results is twice as large as that of the experimental results, but the simulation can accurately capture the flow velocity range where acoustic resonance occurs. The results prove the feasibility of the method of the equivalent diameter of the circular cross-section pipe and the square cross-section pipe to predict acoustic resonance. The pressure pulsation amplitude of acoustic resonance in a square cross-section pipe is significantly increased than that in a circular square cross-section... [more]

This work presents an optimization framework based on mixed-integer programming techniques for a smart home’s optimal energy management. In particular, through a cost-minimization objective function, the developed approach determines the optimal day-ahead energy scheduling of all load types that can be either inelastic or can take part in demand response programs and the charging/discharging programs of an electric vehicle and energy storage. The underlying energy system can also interact with the power grid, exchanging electricity through sales and purchases. The smart home’s energy system also incorporates renewable energy sources in the form of wind and solar power, which generate electrical energy that can be either directly consumed for the home’s requirements, directed to the batteries for charging needs (storage, electric vehicles), or sold back to the power grid for acquiring revenues. Three short-term forecasting processes are implemented for real-time prices, photovoltaics, a... [more]

In this paper, the predictive-based control with bacterial foraging optimization technique for power management in a standalone microgrid is studied and implemented. The heuristic optimization method based on the social foraging behavior of Escherichia coli bacteria is employed to determine the power references from the non-renewable energy sources and loads of the proposed configuration, which consists of a fixed speed diesel generator and battery storage system (BES). The two-stage configuration is controlled to maintain the DC-link voltage constant, regulate the AC voltage and frequency, and improve the power quality, simultaneously. For these tasks, on the AC side, the obtained power references are used as input signals to the predictive-based control. With the help of the system parameters, the predictive-based control computes all possible states of the system on the next sampling time and compares them with the estimated power references obtained using the bacterial foraging opt... [more]

Cooling systems play a key role in maintaining human comfort inside buildings. The key challenges that are facing conventional cooling systems are the rapid growth of total cooling energy and annual electricity consumption in commercial buildings. This is even more significant in countries with an arid climate, where the cooling systems are typically working 80% of the year. Thus, there has been growing interest in developing smart control models to assign optimal cooling setpoints in recent years. In the present work, we propose an occupancy-based control model that is based on a non-linear optimization algorithm to efficiently reduce energy consumption and costs. The model utilizes a Monte-Carlo method to determine the approximate occupancy schedule for building thermal zones. We compare our proposed model to three different strategies, namely: always-on thermostat, schedule-based model, and a rule-based occupancy-driven model. Unlike these three rule-based algorithms, the proposed o... [more]

This paper deals with the state and perspectives of bioenergy development in the context of exploiting the potential of available natural resources. We analyse the economic benefits of transitioning to alternative biofuel within the research task in cooperation with the Vojany black coal power plant. Within the applied methodology, a non-parametric data envelopment analysis method was used to confirm the most economically efficient types of fuels used in the combustion process. The assumption of fuel efficiency was confirmed by testing fuel combustion combinations directly in the power plant. The transition to 100% combustion of solid recovered fuel creates the potential for sustainable production of the analysed power plant and compliance with the current emission values of basic pollutants and new stricter limits, which will be binding in the EU from August 2021. The proposed solutions were analysed by Monte Carlo simulation. An estimate of the economic results achieved by the power... [more]

The role of renewable energy sources in the power grid is increasing tremendously. However, power electronic converters are used to incorporate RES into the grid without inertia. This article recommends an improved emulated inertia control approach focused on the frequency deviation and rate of change of frequency to enhance the inertia of a power system. The required inertial power calculated from emulated inertia control is delivered through hybrid energy storage systems equipped with a proper hybrid energy storage system control. The fast-varying power calculated from emulated inertia control is linked to super-capacitor. Simultaneously, the battery handles the slow varying power by regulating the DC bus voltage proportionate to the frequency variations. Further, the stability of the emulated inertia control and hybrid energy storage system controller is validated by Bode plots. The simulation results verified the correctness of the proposed emulated inertia control and hybrid energ... [more]

This paper reports on an ongoing international effort to establish guidelines for numerical modeling of wave energy converters, initiated by the International Energy Agency Technology Collaboration Program for Ocean Energy Systems. Initial results for point absorbers were presented in previous work, and here we present results for a breakwater-mounted Oscillating Water Column (OWC) device. The experimental model is at scale 1:4 relative to a full-scale installation in a water depth of 12.8 m. The power-extracting air turbine is modeled by an orifice plate of 1−2% of the internal chamber surface area. Measurements of chamber surface elevation, air flow through the orifice, and pressure difference across the orifice are compared with numerical calculations using both weakly-nonlinear potential flow theory and computational fluid dynamics. Both compressible- and incompressible-flow models are considered, and the effects of air compressibility are found to have a significant influence on t... [more]

A high level of moisture in the insulation system of power transformers is often the cause of their failure. This can be prevented by drying a transformer in its place of installation. In the article the application of molecular sieves (MS) in the drying process of the transformer insulation system was analyzed. The water sorption isotherms of 3A MS in mineral oil, natural ester, and synthetic ester at 35 °C were determined, which was not described in the literature before. An evaluation of the influence of temperature on the drying dynamics of electro-insulating liquids using MS was also carried out. The drying dynamics were tested at three temperatures, i.e., 35 °C, 50 °C, and 65 °C, which allowed to analyze the effect of temperature on a short-term or continuous drying process. The tests showed that 3A MS’s ability to adsorb water varied depending on the type of electro-insulating liquid. The determined water sorption isotherms, described by means of Langmuir adsorption model, make... [more]

This paper reviews the basics of series compensation in transmission systems through a literature survey. The benefits that this technology brings to enhance the steady state and dynamic operation of power systems are analyzed. The review outlines the evolution of the series compensation technologies, from mechanically operated switches to line- and self-commutated power electronic devices, covering control issues, different applications, practical realizations, and case studies. Finally, the paper closes with the major challenges that this technology will face in the near future to achieve a fully decarbonized power system.