Energy harvesting is a promising approach to power novel instrumented implants that have passive sensory functions or actuators for therapeutic measures. We recently proposed a new piezoelectric concept for energy harvesting in total hip replacements. The mechanical implant safety and the feasibility of power generation were numerically demonstrated. However, the power output for the chosen piezoelectric element was low. Therefore, we investigated in the present study different geometry variants for an increased power output for in vivo applications. Using the same finite element model, we focused on new, customised piezoelectric element geometries to optimally exploit the available space for integration of the energy harvesting system, while maintaining the mechanical safety of the implant. The result of our iterative design study was an increased power output from 29.8 to 729.9 µW. This amount is sufficient for low-power electronics.

This paper attempts to disclose a new GaN-based device, called the P-Cascode GaN HEMT, which uses only a single gate driver to control both the D-mode GaN and PMOS transistors. The merit of this synchronous buck converter is that it can reduce the circuit complexity of the synchronous buck converter, which is widely used to provide non-isolated power for low-voltage and high-current supply to system chips; therefore, the power conversion efficiency of the converter can be improved. In addition, the high side switch using a single D-mode GaN HEMT, which has no body diode, can prevent the bi-directional flow and thus reduce the power loss and cost compared to a design based on a series of two opposite MOSFETs. The experiment shows that the proposed P-Cascode GaN HEMT efficiency is above 98% when it operates at 500 kHz with 6 W output. With the input voltage at 12 V, the synchronous buck converter provides an adjustable regulated output voltage from 1.2 V to 10 V while delivering a maximu... [more]

Degradation of electrode microstructure is one of the key factors affecting long term performance of Solid Oxide Fuel Cell systems. Evolution of a multiphase system can be described quantitatively by the change in its interfacial energy. In this paper, we discuss free energy of a microstructure to showcase the anisotropy of its evolution during a long-term performance experiment involving an SOFC stack. Ginzburg Landau type functional is used to compute the free energy, using diffuse phase distributions based on Focused Ion Beam Scanning Electron Microscopy images of samples taken from nine different sites within the stack. It is shown that the rate of microstructure evolution differs depending on the position within the stack, similar to phase anisotropy. However, the computed spatial relation does not correlate with the observed distribution of temperature.

Although products can contribute to ecosystems positively, they can cause negative environmental impacts throughout their life cycles, from obtaining raw material, production, and use, to end of life. It is reported that most negative environmental impacts are decided at early design phases, which suggests that the determination of product sustainability should be considered as early as possible, such as during the conceptual design stage, when it is still possible to modify the design concept. However, most of the existing concept evaluation methods or tools are focused on assessing the feasibility or creativity of the concepts generated, lacking the measurements of sustainability of concepts. The paper explores key factors related to sustainable design with regard to environmental impacts, and describes a set of objective measures of sustainable product design concept evaluation, namely, material, production, use, and end of life. The rationales of the four metrics are discussed, wit... [more]

The use of parallel applications in High-Performance Computing (HPC) demands high computing times and energy resources. Inadequate scheduling produces longer computing times which, in turn, increases energy consumption and monetary cost. Task scheduling is an NP-Hard problem; thus, several heuristics methods appear in the literature. The main approaches can be grouped into the following categories: fast heuristics, metaheuristics, and local search. Fast heuristics and metaheuristics are used when pre-scheduling times are short and long, respectively. The third is commonly used when pre-scheduling time is limited by CPU seconds or by objective function evaluations. This paper focuses on optimizing the scheduling of parallel applications, considering the energy consumption during the idle time while no tasks are executing. Additionally, we detail a comparative literature study of the performance of lexicographic variants with local searches adapted to be stochastic and aware of idle ener... [more]

The use of biofuel is one method for limiting the harmful impact of diesel engines on the environment. It is also a way of gradually becoming less dependent on the depleting petroleum resources. New resources for producing biodiesel are currently being sought. The authors produced esters from animal fat waste, obtaining a fuel that can power diesel engines and identifying a way to utilise unnecessary waste. The animal fat methyl ester (AME) was produced using a reactor constructed for non-industrial ester production. The aim underlying this paper was to determine whether a diesel engine can be fuelled with AME biodiesel and to test this fuel’s impact on exhaust gas composition and fuel consumption. Fuelling a Perkins 1104D-44TA engine with AME biodiesel led to a reduction in the smoke opacity of the exhaust gas as well as in carbohydrate, particulate matter, and carbon monoxide concentrations. The carbon dioxide concentrations were similar for biodiesel and diesel fuel. Slight increase... [more]

In selected South Asian countries, the study intends to investigate the relationship between urban population (UP), carbon dioxide (CO2), trade openness (TO), gross domestic product (GDP), foreign direct investment (FDI), and renewable energy (RE). Fully modified ordinary least square (FMOLS) and dynamic ordinary least square (DOLS) models for estimation were used in the study, which covered yearly data from 1990 to 2019. We used Levin−Lin−Chu, Im−Pesaran−Shin, and Fisher PP tests for the stationarity of the variables. The outcomes of the panel cointegration approach looked at whether there was a long-run equilibrium nexus between selected variables in Pakistan, Bangladesh, India, and Sri Lanka. The FMOLS approach was also used to assess the relationship, and the results suggest that there is a significant and negative nexus between FDI and renewable energy in south Asian nations. The study’s findings reveal a strong and favorable relationship between GDP and renewable energy use. In S... [more]

There is wide consensus that Spirulina can serve as a tool for wastewater management and simultaneously provide feedstock for biorefining. However, the economic aspects associated with its use remain a significant challenge. Spirulina cultivated in wastewater decreased the concentrations of both ammonia and nitrate and also served as a biodiesel source. The oil obtained in the feedstock was subjected to transesterification and turned into biodiesel. The biodiesel was subsequently analyzed in a test motor (water-cooled, four-stroke, single-cylinder compression ignition with injection). The tests were conducted at a constant 1500 rpm, and the output power was 3.7 kW. Mixtures of diesel and biodiesel were also enriched with carbon nanotubes (CNTs). The amount of CNTs added to the diesel was 30 mg L−1. The algae and de-oiled biomass were characterized using XRD analysis, and an ultrasonicator was used to mix the CNTs with diesel and spirulina blends. A series of tests were conducted at dif... [more]

In this paper, a voltage-boost-type non-voltage drop single-phase full-bridge inverter connected to a switched-capacitor structure is proposed. The output voltage of the inverter is controlled by the pulse width modulation of a DSP to control the lead and break of the active switches. The full-bridge switches work at low frequency; the other switches work at high frequency. The inverter uses two capacitor modules to charge and discharge alternately so as to overcome the problem of voltage drop on the output side of the inverter in the transition stage from series capacitor discharge to parallel charge. By analyzing the charge−discharge characteristics of the RC charge−discharge circuit, the capacitor charge−discharge cycle can be adjusted to alter the output voltage within a certain range. The results from the physical construction verify the Simulation results achieved well, which demonstrates satisfactory performance that supports the verification of the above theory.

The multi-tier framework (MTF) of electricity access defines a continuum of electrification from tier 0, where access is inexistent or very limited, to tier 5 where access is of grid quality. Transitioning households from lower to higher tiers unlocks the potential in meeting more of their energy needs. This study investigates the transition towards higher tier electricity access on Gilutongan Island, an off-grid island of Cebu, Philippines, which is also an informal settlement community with no open land available for a centralized solar PV system. The solar PV potential of suitable rooftops on the island was determined using satellite imagery, ground measurements, and computation. The electricity demand of a cluster of 11 households was examined in detail; these households, situated near two suitable rooftops, were connected to an installed 7.92 kWp solar PV-based microgrid. Results show that the households moved up from lower to higher tier levels in all MTF attributes except for af... [more]

Torrefaction has been investigated to improve the desirable properties of biomass as solid biofuel, usually used in natura as firewood in several countries. This paper has the main objective to present a broad characterization of the biomass Prosopis juliflora (P. juliflora), investigating its potential as a solid biofuel after its torrefaction process. The methodology was based on different procedures. The experimental runs were carried out at 230, 270, and 310 °C for 30 min, using a bench-scale torrefaction apparatus, with an inert atmosphere. In order to investigate the effect of temperature in constant time, torrefaction parameters were calculated, such as mass yield, energy yield, calorific value, base-to-acid ratio (B/A), and the alkaline index (AI). The physicochemical properties of the torrefied samples were determined and thermogravimetric analysis was used to determine the kinetic parameters at four different heating rates of 5, 10, 20, and 30 °C/min. Pyrolysis kinetics was i... [more]

Reservoirs in Taiwan often provide hydroelectric power, irrigation water, municipal water, and flood control for the whole year. Taiwan has the climatic characteristics of concentrated rainy seasons, instantaneous heavy rains due to typhoons and rainy seasons. In addition, steep rivers in mountainous areas flow fast and furiously. Under such circumstances, reservoirs have to face sudden heavy rainfall and surges in water levels within a short period of time, which often causes the water level to continue to rise to the full level even though hydroelectric units are operating at full capacity, and as reservoirs can only drain the flood water, this results in the waste of hydropower resources. In recent years, the impact of climate change has caused extreme weather events to occur more frequently, increasing the need for flood control, and the reservoir operation has faced severe challenges in order to fulfil its multipurpose requirements. Therefore, in order to avoid the waste of hydrop... [more]

Economic cost is decisive for the development of different power generation. Life cycle cost (LCC) is a useful tool in calculating the cost at all life stages of electricity generation. This study improves the levelized cost of electricity (LCOE) model as the LCC calculation methods from three aspects, including considering the quantification of external cost, expanding the compositions of internal cost, and discounting power generation. The improved LCOE model is applied to three representative kinds of power generation, namely, coal-fired, biomass, and wind power in China, in the base year 2015. The external cost is quantified based on the ReCiPe model and an economic value conversion factor system. Results show that the internal cost of coal-fired, biomass, and wind power are 0.049, 0.098, and 0.081 USD/kWh, separately. With the quantification of external cost, the LCCs of the three are 0.275, 0.249, and 0.081 USD/kWh, respectively. Sensitivity analysis is conducted on the discount... [more]

A cognitive radio ad hoc network (CRAHN) is a mobile network that can communicate without any form of centralized infrastructure. The nodes can learn about the environment and make routing decisions. Furthermore, distributed computing, spectrum mobility, and the Internet of Things have created large data sets, which require more spectrum for data transmission. Unfortunately, the spectrum is a scarce resource that underutilized by licensed users, while unlicensed users are overcrowding the free spectrum. The CRAHNs technology has emerged as a promising solution to the underutilization of the spectrum. The focus of this study is to improve the effectiveness and energy consumption of routing in order to address the routing problem of CRAHNs through the implementation of the optimized cuckoo search algorithm. In CRAHNs, the node and spectrum mobility cause some frequent link breakages within the network, which degrades the performance of the routing protocols. This requires a routing solut... [more]

With the introduction of the renewable energy communities in the current electrical market environment, it becomes possible to aggregate small generation resources and users’ loads to exchange power within the aggregation and at the same time provide services to the electrical system. The renewable energy community of users equipped with nanogrid technology allows performing an adequate level of flexibility. It may be the solution to coordinate in the best possible way the energy resources in order to increase the community self-consumption and to provide ancillary services to the grid. In this paper, a model for the interaction between the Distribution System Operator (DSO)—Transmission System Operator (TSO) and the energy community based on nanogrids is proposed and an operational example is presented.

A special element of road safety research is accidents at the interface of the road and rail system. Due to their low share in the total number of incidents, they are not a popular subject of analyses but rather an element of collective studies, whereas the specificity of the road−rail accidents requires a separate characteristic, allowing, on the one hand, to categorize these types of incidents, and on the other, to specify the factors that affect them, along with an assessment of the strength of this impact. It is important to include in such analyses all potential predictors, both qualitative and quantitative. Moreover, the literature considers most often a number of accidents while, according to the authors, it does not fully reflect the scale of the danger. A better evaluation would be the victim’s degree of injury. Therefore, the purpose of this article is to assess the likelihood of occurrence of various effects of road−rail accidents in the aspect of selected factors. Due to th... [more]

A cost-effective and efficient wind energy production trend leads to larger wind turbine generators and drive for more advanced forecast models to increase their accuracy. This paper proposes a combined forecasting model that consists of empirical mode decomposition, fuzzy group method of data handling neural network, and grey wolf optimization algorithm. A combined K-means and identifying density-based local outliers is applied to detect and clean the outliers of the raw supervisory control and data acquisition data in the proposed forecasting model. Moreover, the empirical mode decomposition is employed to decompose signals and pre-processing data. The fuzzy GMDH neural network is a forecaster engine to estimate the future amount of wind turbines energy production, where the grey wolf optimization is used to optimize the fuzzy GMDH neural network parameters in order to achieve a lower forecasting error. Moreover, the model has been applied using actual data from a pilot onshore wind... [more]

Photogrammetry using unmanned aerial vehicles has become very popular and is already commonly used. The most frequent photogrammetry products are an orthoimage, digital terrain model and a 3D object model. When executing measurement flights, it may happen that there are unsuitable lighting conditions, and the flight itself is fast and not very stable. As a result, noise and blur appear on the images, and the images themselves can have too low of a resolution to satisfy the quality requirements for a photogrammetric product. In such cases, the obtained images are useless or will significantly reduce the quality of the end-product of low-level photogrammetry. A new polymodal method of improving measurement image quality has been proposed to avoid such issues. The method discussed in this article removes degrading factors from the images and, as a consequence, improves the geometric and interpretative quality of a photogrammetric product. The author analyzed 17 various image degradation c... [more]

Electricity supply quality (ESQ) is critical for healthy economic production, and regional differences in ESQ can widen economic development gaps. To contribute to a more equitable regional development, this study first develops a Gini index of ESQ distribution to measure the inequality among different cities. Then, an econometric model based on the Cobb−Douglas production function is established to quantify the effects of ESQ on regional economy. Finally, we estimate the impacts of ESQ improvement on reducing the economic inequality. The main results show that: (1) Substantial differences exist among the regional ESQ, and the national GDP-based ESQ Gini index was 0.720 in 2018. (2) A GDP-based Lorenz curve has a higher Gini coefficient than the population-based one does, while inequalities in cites are greater than those in rural areas. (3) The ESQ has significant impacts on the regional economic output, and a 1% reduction in the ESQ will, on average, reduce the city-level output by 0... [more]

A building energy performance gap can be illustrated as the difference between the theoretical (methodologically defined) and the actual energy consumption. In EU countries, Energy Performance Certificates are issued when buildings are constructed, sold, or leased. This information is the first step in order to evaluate the energy performance of the building stock. In Serbia, when issuing an energy certificate, the adopted national methodology recognizes only energy consumption for heating. The main purpose of this paper is to evaluate the energy gap and estimate the relevance of an Energy Performance Certificate to meet the national energy efficiency or carbon target. An Energy Performance Certificate determines the theoretical residential and commercial building energy efficiency or its “design intent”. This research stresses the necessity of measuring and achieving reductions in actual energy consumption through system regulation and consumers’ self-awareness in buildings. The resea... [more]

With the gradual declining of oil increment performance of CO2 huff-and-puff wells, the overall oil exchange rate shows a downward tendency. In this regard, CO2 synergistic huff-and-puff technologies have been proposed to maintain the excellent effect and extend the technical life of such wells. However, there is no specific research on the mechanism and synergistic mode of CO2 huff and puff in horizontal wells. This study aims to establish the synergistic mode and determine the adaptability and acting mechanism of CO2 synergistic huff and puff. Three synergistic huff-and-puff modes are proposed based on the peculiarity of the fault-block reservoir’s small oil-bearing area and broken geological structure. We establish three typical CO2 synergistic huff-and-puff models and analyze the influence of different geological and development factors on the huff-and-puff performance with numerical simulation. Each factor’s sensitivity is clarified, and the enhanced oil recovery (EOR) mechanism o... [more]

The growing adoption of decentralised renewable energy generation (such as solar photovoltaic panels and wind turbines) and low-carbon technologies will increase the strain experienced by the distribution networks in the near future. In such a scenario, energy storage is becoming a key alternative to traditional expensive reinforcements to network infrastructure, due to its flexibility, decreasing costs and fast deployment capabilities. In this work, an end-to-end data-driven solution to optimally design the control of a battery unit with the aim of reducing the peak electricity demand is presented. The proposed solution uses state-of-the-art machine learning methods for forecasting electricity demand and PV generation, combined with an optimisation strategy to maximise the use of photovoltaic energy to charge the energy storage unit. To this end, historical demand, weather, and solar energy generation data collected at the Stentaway Primary substation near Plymouth, UK, and at other s... [more]

This paper investigates the effect of ground and fumed silica fillers on suppressing DC erosion in silicone rubber. Fumed silica and ground silica fillers are incorporated in silicone rubber at different loading levels and comparatively analyzed in this study. Outcomes of the +DC inclined plane tracking erosion test indicate a better erosion performance for the fumed silica filled composite despite having a lower thermal conductivity compared to the ground silica composite. Results of the simultaneous thermogravimetric and thermal differential analyses are correlated with inclined plane tracking erosion test outcomes suggesting that fumed silica suppresses depolymerization and promotes radical based crosslinking in silicone rubber. This finding is evident as higher residue is obtained with the fumed silica filler despite being filled at a significantly lower loading level compared to ground silica. The surface residue morphology obtained, and the roughness determined for the tested sam... [more]

The refurbishment of the building stock is a key strategy towards the achievement of the climate and energy goals of the European Union. This study aims at evaluating the energy and environmental impacts associated with retrofitting a residential apartment to improve its vertical envelope thermal insulation. Two insulation materials, stone wool and cellulose fibers, are compared. The life cycle assessment methodology is applied assuming 1 m2 of retrofitted vertical envelope as functional unit. Moreover, to estimate the net energy and environmental benefits achievable in the retrofitted scenario compared with the non-retrofitted one, a second analysis is performed in which the system boundaries are expanded to include the building operational phase, and 1 m2 of walkable floor per year is assumed as reference. The results show that the use of cellulose fibers involve lower impacts in most of the assessed categories compared to stone wool, except for abiotic resource depletion. In detail,... [more]

The presence of different pollutants in recycled plastics is reviewed in this article. The desirable circular economy of plastics should be linked to the availability of clean recycled plastics with a non-significant and small to nil amount of substances of concern. Different researchers found polycyclic aromatic hydrocarbons (PAHs) and Persistent Organic Pollutants (POPs), such as brominated flame retardants (BFRs), pesticides, dioxins and furans (PCDD/Fs and PBDD/Fs) in plastic recyclates. This represents an added difficulty to the effective recycling process of plastics that reduces the demand for energy and materials, in addition to posing a great environmental danger since they represent a vector of accumulation of the contaminants that will finally appear in the most unexpected products. Life Cycle Analysis of the plastic wastes recycling process indicates a great saving of energy, water and CO2 emissions.