The gas−liquid hydrodynamics and mass transfer were studied in a concentric tube internal jet-loop airlift reactor with a conical bottom. Comparing with a standard design, the gas separator was equipped with an adjustable deflector placed above the riser. The effect of riser superficial gas velocity uSGR on the total gas holdup εGT, homogenization time tH, and overall volumetric liquid-phase mass transfer coefficient kLa was investigated in a laboratory bioreactor, of 300 mm in inner diameter, in a two-phase air−water system and three-phase air−water−PVC−particle system with the volumetric solid fraction of 1% for various deflector clearances. The airlift was operated in the range of riser superficial gas velocity from 0.011 to 0.045 m/s. For the gas−liquid system, when reducing the deflector clearance, the total gas holdup decreased, the homogenization time increased twice compared to the highest deflector clearance tested, and the overall volumetric mass transfer coefficient slightly... [more]

Fossil fuel power plants can cause numerous environmental issues, owing to exhaust emissions and substantial water consumption. In a thermal power plant, heat and water recovery from flue gas can reduce CO2 emissions and water demand. High-humidity flue gas averts the diffusion of pollutants, enhances the secondary transformation of air pollutants, and leads to smog weather; hence, water recovery from flue gas can also help to lessen the incidence of white plumes and smog near and around the power plant. In this study, a lab-scale system for heat and water recovery from flue gas was tested. The flue gas was initially cooled by an organic Rankine cycle (ORC) system to produce power. This gas was further cooled by an aftercooler, using the same working fluid to condense the water and condensable particulate matter in the flue gas. The ORC system can produce approximately 220 W of additional power from flue gas at 140 °C, with a thermal efficiency of 10%. By cooling the flue gas below 30−... [more]

The present study experimentally and numerically investigates the effect of channel height on the flow and heat transfer characteristics of a channel impingement cooling configuration for various jet Reynolds numbers in the range of 2000−8600. A single array consisting of eleven jets with 0.8 mm diameter injects water into the channel with 2 mm width at four different channel heights (3, 4, 5, and 6 mm). The average heat transfer coefficients at the target surface are measured by maintaining a temperature difference between the jet exit and the target surface in the range of 15−17 °C for each channel height. The experimental results show the average heat transfer coefficient at the target surface increases with the jet Reynolds number and decreases with the channel height. An average Nusselt number correlation is developed based on 85 experimentally measured data points with a mean absolute error of less than 4.31%. The numerical simulation accurately predicts the overall heat transfer... [more]

HVDC grids demand the fast and reliable operation of the protection system. The failure of any protection element should initialize a backup protection almost immediately in order to assure the system’s stability. This paper proposes a novel backup strategy that covers the failure of the primary protection including the malfunctioning of the HVDC circuit breaker. Only local voltage measurements are employed in the proposed backup protection and the voltage derivative is calculated at both sides of the limiting inductor. Consequently, the speed and reliability of the protection system are enhanced, since no communication channel is needed. This paper contains a thorough specification of the proposed protection strategy. This strategy is validated in a four-terminal HVDC grid with various fault case scenarios, including high-resistance fault cases. The operation of the backup protection is reliable and remarkably fast.

The underground coal gasification (UCG) represents an effective coal mining technology, where coal is transformed into syngas underground. Extracted syngas is cleaned and processed for energy production. Various gasification agents can be injected into an underground georeactor, e.g., air, technical oxygen, or water steam, to ensure necessary temperature and produce syngas with the highest possible calorific value. This paper presents an experimental study where dynamic optimization of operating variables maximizes syngas calorific value during gasification. Several experiments performed on an ex situ reactor show that the optimization algorithm increased syngas calorific value. Three operation variables, i.e., airflow, oxygen flow, and syngas exhaust, were continually optimized by an algorithm of gradient method. By optimizing the manipulation variables, the calorific value of the syngas was increased by 5 MJ/m3, both in gasification with air and additional oxygen. Furthermore, a high... [more]

In year-round hot climatic conditions, conventional air conditioning systems consume significant amounts of electricity primarily generated by conventional power plants. A compression-assisted, multi-ejector space cooling system driven by low-grade solar thermal energy is investigated in terms of energy and exergy performance, using a real gas property-based ejector model for a 36 kW-scale air conditioning application, exposed to annually high outdoor temperatures (i.e., up to 42 °C), for four working fluids (R11, R141b, R245fa, R600a). Using R245fa, the multi-ejector system effectively triples the operating condenser temperature range of a single ejector system to cover the range of annual outdoor conditions, while compression boosting reduces the generator heat input requirement and improves the overall refrigeration coefficient of performance (COP) by factors of ~3−8 at medium- to high-bound condenser temperatures, relative to simple ejector cycles. The system solar fraction varies... [more]

The storage of natural gas in geological structures such as depleted fields, aquifers and salt caverns plays an important role in a gas supply system as it balances the fluctuation of gas demand and price. Hydraulic loss due to fluid flow through gas storage production equipment and an interfering effect from nonequal productivity index of storage wells may have an important influence on gas storage performance. An integrated mathematical model is developed based on underground gas storage facility production data. Using this model, the hydraulic loss is determined. A real test case that consists of a gas storage reservoir linked to the surface facility is analysed. The mathematical model uses an experimentally determined pressure drop coefficient in chokes. The base case scenario created using real gas storage facility data enables the achievement of a good history match with the given parameters of the gas storage reservoir. Using the history match simulation case as an initial scena... [more]

This paper focuses on the analysis of trends in the development of nuclear energy in selected European and non-European countries in the context of the pace of renewable energy development in the world. The perception of Poles related to their openness to various energy sources against the background of European trends was also examined, as well as their ecological approach to the quality of the environment in this context. The survey was carried out using the Computer Assisted Web Interview (CAWI) technique. The total number of correctly completed forms was 923. To identify the ecological attitude, purchasing attitude, and the perception of nuclear energy, the research tool contained a number of statements on the issues studied, and the respondents assessed compliance with their opinion using a seven-point bipolar scale. The semantic differential was also used to gather opinions on the characteristics of nuclear energy. This paper shows that global trends are promoting the development... [more]

As long as non-contact digital printing remains an uncommon standard in the corrugated packaging industry, corrugated board crushing remains a real issue that affects the load capacity of boxes. Crushing mainly occurs during the converting of corrugated board (e.g., analog flexographic printing or laminating) and is a process that cannot be avoided. However, as this study shows, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision of ±10 μm) in the range from 10 to 70% on different laboratory measurements was checked. The typical mechanical tests—i.e., edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc.—were performed on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for buildin... [more]

Countries globally are focusing on alternative fuels to reduce the environmental pollution. An example is biodiesel fuel, which is leading the way to other technologies. In this research, the methyl esters of castor oil were prepared using a two-step transesterification process. The respective properties of the castor oil (Ricinus Communis) biodiesel were estimated using ASTM standards. The effect of performance and emission on diesel engines was noted for four various engine loads (25, 50, 75, and 100%), with two different blends (B5 and B20) and at two different engine speeds (1500 and 2000 rpm). The study determined that B5 and B20 samples at 1500 rpm engine speed obtained the same power, but diesel fuel generated greater control. The power increased at 2000 rpm for B5 samples, but B20 samples, as well as diesel, were almost the same values. In the 40−80% range, load and load values were entirely parallel for each load observed from the engine performance of the brake power in all s... [more]

Infrared thermography has been used as a key means for the identification of overheating defects in power cable accessories. At present, analysis of thermal imaging pictures relies on human visual inspections, which is time-consuming and laborious and requires engineering expertise. In order to realize intelligent, autonomous recognition of infrared images taken from electrical equipment, previous studies reported preliminary work in preprocessing of infrared images and in the extraction of key feature parameters, which were then used to train neural networks. However, the key features required manual selection, and previous reports showed no practical implementations. In this contribution, an autonomous diagnosis method, which is based on the Faster RCNN network and the Mean-Shift algorithm, is proposed. Firstly, the Faster RCNN network is trained to implement the autonomous identification and positioning of the objects to be diagnosed in the infrared images. Then, the Mean-Shift algo... [more]

With the increased adoption of distributed energy resources (DERs) and renewables, such as solar panels at the building level, consumers turn into prosumers with generation capability to supply their on-site demand. The temporal complementarity between supply and demand at the building level provides opportunities for energy exchange between prosumers and consumers towards community-level self-sufficiency. Investigating different aspects of community-level energy exchange in cyber and physical layers has received attention in recent years with the increase in renewables adoption. In this study, we have presented an in-depth investigation into the impact of energy exchange through the quantification of temporal energy deficit−surplus complementarity and its associated self-sufficiency capacities by considering the impact of variations in community infrastructure configurations, variations in household energy use patterns, and the potential for user adaptation for load flexibility. To th... [more]

Methanol synthesis from carbon dioxide (CO2) may contribute to carbon capture and utilization, energy fluctuation control and the availability of CO2-neutral fuels. However, methanol synthesis is challenging due to the stringent thermodynamics. Several catalysts mainly based on the carrier material Al2O3 have been investigated. Few results on MgO as carrier material have been published. The focus of this study is the carrier material MgO. The caustic properties of MgO depend on the caustification/sintering temperature. This paper presents the first results of the activity of a Cu/MgO catalyst for the low calcining temperature of 823 K. For the chosen calcining conditions, MgO is highly active with respect to its CO2 adsorption capacity. The Cu/MgO catalyst showed good catalytic activity in CO2 hydrogenation with a high selectivity for methanol. In repeated cycles of reactant consumption and product condensation followed by reactant re-dosing, an overall relative conversion of CO2 of 76... [more]

This paper analyzes electricity markets in Slovenia during the specific period of market deregulation and price liberalization. The drivers of electricity prices and electricity consumption are investigated. The Slovenian electricity markets are analyzed in relation with the European Energy Exchange (EEX) market. Associations between electricity prices on the one hand, and primary energy prices, variation in air temperature, daily maximum electricity power, and cross-border grid prices on the other hand, are analyzed separately for industrial and household consumers. Monthly data are used in a regression analysis during the period of Slovenia’s electricity market deregulation and price liberalization. Empirical results show that electricity prices achieved in the EEX market were significantly associated with primary energy prices. In Slovenia, the prices for daily maximum electricity power were significantly associated with electricity prices achieved on the EEX market. The increases i... [more]

There are international activities and on-going initiatives, particularly at the European level, to define what Positive Energy Districts should be, as the driving concept for the urban transition to a sustainable future. The first objective of the paper is to contribute to the on-going and lively debate about the definition of the notion of Sustainable Plus Energy Neighbourhood (SPEN), which highlights the multiple dimensions when talking about sustainability in districts moving beyond the traditional and strict building energy assessment. Based on a holistic methodology which ensures the consideration of the multidimensional nature and goals of SPEN, the paper outlines an evaluation framework. The evaluation framework defines the key performance indicators distributed in five categories that consider energy and power performance, GHG emissions, indoor environmental quality, smartness, flexibility, life cycle costs and social sustainability. This framework is designed to be implemente... [more]

In 2020, residential sector loads reached 25% of the overall electrical consumption in Europe and it is foreseen to stabilise at 29% by 2050. However, this relatively small increase demands, among others, changes in the energy consuming behaviour of households. To achieve this, Demand Response (DR) has been identified as a promising tool for unlocking the hidden flexibility potential of residential consumption. In this work, a holistic incentive-based DR framework aiming towards load shifting is proposed for residential applications. The proposed framework is characterised by several innovative features, mainly the formulation of the optimisation problem, which models user satisfaction and the economic operation of a distributed household portfolio, the customised load forecasting algorithm, which employs an adjusted Gradient Boosting Tree methodology with enhanced feature extraction and, finally, a disaggregation tool, which considers electrical features and time of use information. T... [more]

In recent years, the evaluation of several energy sources is an extremely significant issue that affects socio-environmental development and techno-economic growth in different sectors. To tackle this concern, many researchers have concentrated on preferring desirable energy sources and adopting multi-criteria group decision-making (MCGDM) approaches for only a single type of user (e.g., agricultural, industrial, tourism, or domestic users). However, every energy user plays an important role in shaping energy policy. In fact, for sustainable energy, it is important to include all main energy users at the same time in energy decision-making. The main objective of this work was to propose a fuzzy MCGDM approach to evaluate and prioritize energy sources in Tunisia from various sectors’ point of views. Many criteria are combined, including the following: technical, economic, social, political and environmental. After applying the fuzzy Delphi method, the proposed approach consists of apply... [more]

The goal of reducing the climate impact of shipping requires many different activities. To reduce greenhouse gas emissions, the International Maritime Organization prepared some proposals to meet and fulfill the requirements. It sets out the provisions of the International Convention for the Prevention of Pollution from Ships 73/78 Annex 6—Prevention of the Air Pollution from Ships (1997) with the amendments and the future objectives set. The main objective is to achieve climate neutrality from shipping by 2050. One method is the decarbonization of marine fuels. The types of fuels that are transient fuels, with the final target fuel being hydrogen, are shown. Carbon dioxide emissions depend on the chemical composition of the fuel, its Lower Heating Value and the engine efficiency. The aim of the manuscript is to demonstrate that the use of fuels with lower carbon content is a transitional process enabling the hydrogen era to take place. An analysis of this problem is presented as a rev... [more]

One of the main challenges in smart city models is consumer behaviour, namely guiding the efforts to promote optimal use of energy in the dynamics of the developing cities, through lower energy consumption without impact on the comfort level. This relates to all energy vectors and can be done through different means. The uptake stage of smart metering and information and communication technologies (ICT) varies in different countries, creating the need for tailored innovative approaches in motivating behavioural change. This paper presents the work carried out within the joint research project ITCity (an ICT platform for sustainable energy ecosystem in smart cities) between the European Union and Latin American Countries. Cooperation of energy researchers and experts in ICT and application developers facilitates adoption of a multipurpose interdisciplinary approach. This work aims at providing the smart city and energy research and innovation community broader understanding of factors i... [more]

Circular economy (CE) is an economic model, in which raw materials remain in circulation as long as possible and the generation of waste is minimized. In the fertilizer sector, waste rich in nutrients should be directed to agriculture purposes. This paper presents an analysis of recommended directions for the use of nutrient-rich waste in fertilizer sector and an evaluation of possible interest in this kind of fertilizer by a selected group of end-users (nurseries). The scope of research includes the state-of-the-art analysis on circular aspects and recommended directions in the CE implementation in the fertilizer sector (with focus on sewage-based waste), and survey analysis on the potential interest of nurseries in the use of waste-based fertilizers in Poland. There are more and more recommendations for the use of waste for agriculture purposes at European and national levels. The waste-based products have to meet certain requirements in order to put such products on the marker. Nurs... [more]

Dual fuel engines induce benefits in terms of pollutant emissions of PM and NOx together with carbon dioxide reduction and being powered by natural gas (mainly methane) characterized by a low C/H ratio. Therefore, using natural gas (NG) in diesel engines can be a viable solution to reevaluate this type of engine and to prevent its disappearance from the automotive market, as it is a well-established technology in both energy and transportation fields. It is characterized by high performance and reliability. Nevertheless, further improvements are needed in terms of the optimization of combustion development, a more efficient oxidation, and a more efficient exploitation of gaseous fuel energy. To this aim, in this work, a CFD numerical methodology is described to simulate the processes that characterize combustion in a light-duty diesel engine in dual fuel mode by analyzing the effects of the changes in engine speed on the interaction between fluid-dynamics and chemistry as well as when... [more]

The fast depletion of fossil fuels and the growing awareness of the need for environmental protection have led us to the energy crisis. Positive development has been achieved since the last decade by the collective effort of scientists. In this regard, renewable energy sources (RES) are being deployed in the power system to meet the energy demand. The microgrid concept (AC, DC) is introduced, in which distributed energy resources (DERs), the energy storage system (ESS) and loads are interconnected. DC microgrids are appreciated due to their high efficiency and reliability performance. Despite its significant growth, the DC microgrid is still relatively novel in terms of grid architecture and control systems. In this context, an energy management system (EMS) is essential for the optimal use of DERs in secure, reliable, and intelligent ways. Therefore, this paper strives to shed light on DC microgrid architecture, control structure, and EMS. With an extensive literature survey on EMSs’... [more]

Tire yaw marks deposited on the road surface carry a lot of information of paramount importance for the analysis of vehicle accidents. They can be used: (a) in a macro-scale for establishing the vehicle’s positions and orientation as well as an estimation of the vehicle’s speed at the start of yawing; (b) in a micro-scale for inferring among others things the braking or acceleration status of the wheels from the topology of the striations forming the mark. A mathematical model of how the striations will appear has been developed. The model is universal, i.e., it applies to a tire moving along any trajectory with variable curvature, and it takes into account the forces and torques which are calculated by solving a system of non-linear equations of vehicle dynamics. It was validated in the program developed by the author, in which the vehicle is represented by a 36 degree of freedom multi-body system with the TMeasy tire model. The mark-creating model shows good compliance with experimen... [more]

The main reason for the limited usage of biodiesel is it tends to oxidize when exposed to air. It is anticipated that the addition of an antioxidant along with graphene nano particle improves combustion of diesel-biodiesel blend. In the present research biodiesel made from the transesterification of waste cooking oil is used. Three synthetic antioxidants butylated hydroxytoluene (BHT), 2(3)-t-butyl-4-hydroxyanisole (BHA) and tert butylhydroquinone (TBHQ) along with 30 ppm of graphene nano particle were added at a volume fraction of 1000 ppm to diesel−biodiesel blends (B20). The performance and emission tests were performed at constant engine speed of 1500 rpm. Because of the inclusion of graphene nano particles, surface area to the volume ratio of the fuel is augmented enhancing the mixing ability and chemical responsiveness of the fuel during burning causing superior performance, combustion and emission aspects of compression ignition engine. The results revealed that there was a slig... [more]

Energy and exergy (EnE) efficiencies are considered the most important parameters to compare the performance of various thermal systems. In this paper, an analysis was carried out for EnE efficiencies of a flat plate solar collector (FPSC) using four different kinds of nanofluids as flowing mediums, namely, Al2O3/water, MgO/water, TiO2/water, and CuO/water, and compared with water as a flowing medium (traditional base fluid). The analysis considered nanofluids made of nanomaterials’ volume fractions of 1−4% with water. The volume flow rates of nanofluids and water were 1 to 4 L/min. The solar collector′s highest EnE efficiency values were obtained for CuO/water nanofluid among the four types of nanofluids mentioned above. The EnE efficiencies of the CuO nanofluid-operated solar collector were 38.21% and 34.06%, respectively, which is significantly higher than that of water-operated solar collectors. For the same volume flow rate, the mass flow rate was found to be 15.95% higher than wa... [more]