Due to the design of peanut harvesters and cleaners, peanut pods are often mixed with soil, gravel, peanut straw, and other impurities. To solve this problem, this study focused on designing a peanut pod cleaning device by integrating a negative pressure centrifugal fan, a hydrometric cleaning sieve, and a reversible long-mesh cleaning sieve. The relative motion of the peanut pod on the sieve was discussed, its stress analyzed, the design parameters of the sieve and fan determined, and the operation of the device was monitored by using sensors, which accurately recorded and adjusted the working parameters. Finally, the key parameters were tested, and the results showed that the design requirements were met at a vibration frequency of 5.5 Hz, a hydrometric cleaning sieve inclination of 15°, a reciprocating long mesh cleaning sieve inclination of 5°, and a fan speed of 1500 rev/min; the mean loss is 2.26%, and the mean impurity is 3.18%. The findings can be used to provide technical supp... [more]

At present, complex biological processes are used in many industrial areas [...]

In this study, a procedure for selecting the optimal heat-accumulating material based on phase transitions for the economical maintenance of poultry farms by applying ANOVA to complex solid bodies’ thermodynamic parameters is described. The relevance of the topic is due to its importance for the development of an energy-saving technology based on the release or absorption of significant heat during the crystallization or melting of materials. The applicability of one-way ANOVA for the selection of the optimal material with a specific functional purpose was demonstrated. As result, the best composition for maintaining a normal temperature regime in poultry farms that could meet all the requirements imposed on heat-storage materials was determined. It was found that magnesium sulphate heptahydrate is such a material.

From the textile manufacturers’ point of view, coarse and medullated fibers are undesirable in the production of fine woolen materials, but highly desirable in the production of textiles and yarns with special effects, especially in carpet production. For sustainability, the entire sheep fleece should be used, including the coarse and medullated fibers. The raw wool must be scoured to obtain clean wool fibers without damage or excessive fiber entanglement, with a certain moisture content, low dirt content and residual grease for further processing, and proper color. In order to remove the impurities in raw wool with maximum efficiency, save energy and minimize the environmental impact, this study investigated the changes in some fiber properties during the scouring process due to the effect of the enzyme complex on coarse wool fibers. The effects were studied through the amount of clean wool fibers and impurities within the fleece, the fiber diameter and color. Conventional and enzyme... [more]

Betulinic acid, BA, is a lupane derivative that has caught the interest of researchers due to the wide variety of pharmacological properties it exhibits towards tumor cells. Because of their prospective increased anti−proliferative efficacy and improved pharmacological profile, BA derivatives continue to be described in the scientific literature. The current work was conducted in order to determine the antiproliferative activity, under an in vitro environment of the newly developed 1,2,4−triazole derivatives of BA. The compounds and their reaction intermediates were tested on three cancer cell lines, namely RPMI−7951 human malignant melanoma, HT−29 colorectal adenocarcinoma, A549 lung carcinoma, and healthy cell line (HaCaT human keratinocytes). BA−triazole derivatives 4a and 4b revealed lower IC50 values in almost all cases when compared to their precursors, exhibiting the highest cytotoxicity against the RPMI−7951 cell line (IC50: 18.8 μM for 4a and 20.7 μM for 4b). Further biologica... [more]

Most industrial systems today are nonlinear and dynamic. Traditional fault detection techniques show their limits because they can hardly extract both nonlinear and dynamic features simultaneously. Canonical variate analysis (CVA) shows its excellent monitoring performance in fault detection for dynamic processes but is not applicable to nonlinear processes. Inspired by the CVA method, a novel nonlinear dynamic process monitoring method, namely, the “canonical variate kernel analysis” (CVKA), is proposed in this work. The way to extract nonlinear features is different from a traditional kernel canonical variate analysis (KCVA). In a sequential structure, the new approach firstly extracts the linear dynamic features from the data through the CVA method, followed by a kernel principal component analysis to extract nonlinear features from the CVA residual space. The new CVKA method is then applied to a TE process case study, proving the excellent performance of CVKA compared to other comm... [more]

In order to find out the root cause of cross bearer welds’ cracks in general-purpose gondola cars, the relationship between asymmetric structure and stress distribution is studied in this paper. Firstly, the concept of asymmetry coefficient and stress distribution cluster is proposed, and the asymmetric coefficients’ calculation methods of independent and dependent variables are given, respectively, in two-dimensional space. Secondly, according to the different positions of side column 1 and side column 2, 30 local models are established, the cross bearer weld stresses are extracted after finite element simulation, and the stress distribution clusters of cross bearer weld stresses are formed. Finally, the asymmetry coefficients of the side columns are calculated, and the correlation between the positions of the side columns and the weld stresses is studied using the methods of Pearson correlation coefficient and complex correlation coefficient. The results show that the correlation bet... [more]

The ambitious targets set by the International Maritime Organization for reducing greenhouse gas emissions from shipping require radical actions by all relevant stakeholders. In this context, the interest in high efficiency and low emissions (even zero in the case of hydrogen) fuel cell technology for maritime applications has been rising during the last decade, pushing the research developed by academia and industries. This paper aims to present a comparative review of the fuel cell systems suitable for the maritime field, focusing on PEMFC and SOFC technologies. This choice is due to the spread of these fuel cell types concerning the other ones in the maritime field. The following issues are analyzed in detail: (i) the main characteristics of fuel cell systems; (ii) the available technology suppliers; (iii) international policies for fuel cells onboard ships; (iv) past and ongoing projects at the international level that aim to assess fuel cell applications in the maritime industry;... [more]

Supply chain management is one of the most prominent areas that needs to incorporate sustainability to achieve responsible consumption and production (SDG 11).It has been identified that there are limited studies that have presented the significance of different Industry 4.0 technologies from the perspective of sustainable SCM. The purpose of this study is to discuss the role of Industry 4.0 technologies in the context of sustainable SCM, as well as to identify important areas for future research. The PRISM framework is followed to discuss the role and significance of sustainable SCM and the integration of Industry 4.0-enabling technologies such as the Internet of Things (IoT), cloud computing, big data, artificial intelligence (AI), blockchain, and digital twin for sustainable SCM. The findings of the study reveal that there are limited empirical studies for developing countries and the majority are emphasized in case studies. Additionally, a few studies have focused on operational as... [more]

Foods from grains and grain-derived ingredients are among the most important energy and nutrient source for humans [...]

Biofuel production has increased significantly in several countries in recent decades. Different evaluation techniques are required for their characterization. The study measures the properties of the obtained biodiesel and a commercial diesel sample, using the techniques of open circuit potential, linear scanning voltammetry and electrochemical impedance spectroscopy. The transesterification reaction between sunflower oil and methanol was carried out with ultrasound as the energy source. The determination of triglyceride conversion to biodiesel is performed by high performance liquid chromatography (HPLC), obtaining up to 99.79% with a yield of 93.40% at a transesterification temperature of 50 ∘C for 60 min with a methanol/oil molar ratio of 6:1. The potassium hydroxide catalyst concentration was 1.0 g catalyst/100 g oil. The biodiesel samples generally showed open circuit potential (OCP) values less than 790 mV and stabilization time less than 120 s, Linear sweep voltammograms (LSV)... [more]

Taking a direct-drive volume control (DDVC) electro-hydraulic servo system as the research object and aiming at the problems of the servo motor torque fluctuation, high-precision system pressure control, and dynamic response of the system, based on traditional motor direct torque control (DTC), a motor direct torque control method based on a sliding-mode variable structure is proposed to control the system pressure. The motor torque loop is part of the inner control loop and has a rapid dynamic response speed, resulting in higher pressure control accuracy. A nonlinear mathematical model was established for the DDVC electro-hydraulic servo system. The switch meter hysteresis controller in the traditional DTC system was replaced with space vector pulse-width modulation technology. Then, the PID control module in space vector modulation technology was replaced with high-order sliding-mode variable-structure control. Through the coupling relationship between the electric machine and the co... [more]

Fine-blanking is a molding process based on the common blanking process, which obtains hydrostatic stress through blank holder reverse jacking, in order to increase material plasticity. It requires special equipment, namely a fine-blanking press, to complete the fine-blanking process. In this paper, the problem of the speed of the slide block fluctuation found in the actual use of a 12,000 kN hydraulic fine-blanking press after multi-stage pressure source optimization is studied. Firstly, the mathematical model of the motion of the slide block in the blanking stage of the hydraulic fine blanking press is established, and the accurate mathematical model in the blanking stage of the hydraulic fine-blanking press is obtained through the least square method system identification experiment. Aiming at the complex working situation of the fine-blanking press, a phased PID control strategy is creatively proposed. The optimal PID control parameters are obtained by a genetic algorithm, and esta... [more]

Genetically modified (GM) technology is of great significance for increasing crop production, protecting biodiversity, and reducing environmental pollution. However, with the frequent occurrence of safety events regarding GM foods, more and more disputes have arisen over the potential safety of transgenic technology. It is particularly necessary to find a fast and accurate method for transgenic product identification. In this research, mid-infrared spectroscopy, coupled with chemometric methods, was applied to discriminate GM maize from its non-GM parent. A total of 120 GM maize and 120 non-GM maize samples were prepared, and the spectral information in the range of 400−4000 cm−1 was collected. After acquiring the spectra, wavelet transform (WT) was used to preprocess the data, and k-means was carried out to split all samples into calibration and prediction sets in the ratio of 2:1. Principal component analysis (PCA) was then conducted to qualitatively distinguish the two types of samp... [more]

The purpose of the study was to evaluate the properties of by-products obtained from the oil industry, to identify the content of bioactive compounds and to test the safety of their reintroduction in the food industry. Three sunflower meals obtained after cold-pressing of whole (WSM), partially dehulled (PSM) and total dehulled (TSM) sunflower seeds were used. A higher protein, ash and fiber content was obtained for WSM, followed by PSM, and TSM meals. Conversely, the lipid content was higher in TSM and PSM, and lower in WSM meals. Sunflower meals are important sources of unsaturated fatty acids (more linoleic than oleic acid), the content ranging between 82.74 and 86.72%. Additionally, sunflower meals represent a significant source of compounds with antioxidant activity. TSM showed the highest concentration of total polyphenols and total flavonoids, while WSM the lowest. The values of antioxidant activity were higher for TSM compared to PSM and WSM. The weak cytotoxic activity at conc... [more]

The smart chemical laboratory has recently emerged as a promising trend for future chemical research, where experiment optimization is of vital importance. The traditional Bayesian optimization (BO) algorithm focuses on exploring the dependent variable space while overlooking the independent variable space. Consequently, the BO algorithm suffers from becoming stuck at local optima, which severely deteriorates the optimization performance, especially with bad-quality initial points. Herein, we propose a novel stochastic framework of Bayesian optimization with D-optimal design (BODO) by integrating BO with D-optimal design. BODO can balance the exploitation in the dependent variable space and the exploration in the independent variable space. We highlight the excellent performance of BODO even with poor initial points on the benchmark alpine2 function. Meanwhile, BODO demonstrates a better average objective function value than BO on the benchmark Summit SnAr chemical process, showing its... [more]

The recovery of metal resources from wastewater is very important for both resource recovery and wastewater treatment. Compared with traditional metal-polluted wastewater treatment technologies, advanced wastewater treatment technologies with the functions of both recovering metals and generating electricity have been developed rapidly in recent years. These advanced technologies include microbial fuel cells, photo fuel cells, coupled redox fuel cells, etc. In this paper, these advanced technologies are elaborated from their principles to their applications in wastewater treatment for metals recovery and electricity generation. The recent progress of these technologies was also reviewed. The effects of different metal ions, cell configurations, and various operating parameters on their performance were also discussed. Although these technologies are promising, the challenges and the efforts needed to overcome them are also highlighted.

The genus Achillea has significant medical potential due to the presence of highly bioactive compounds in its chemical composition. To take advantage of plants’ biomedical potential, it is of great importance to use a proper extraction process. This study aimed to determine and compare the preliminary chemical composition of five different Achillea species extracted with two conventional (infusion and maceration) and two non-conventional (ultrasound-assisted extraction (UAE) and Subcritical water extraction (SWE)) techniques. The extracts were prepared using the previously described procedures for infusion, maceration, UAE and SWE extraction. For all extracts, the extraction yield (dry extract (DE)) was determined. The analyzed extracts were preliminarily chemically characterized spectrophotometrically in terms of total phenolic content (TPC) and total flavonoid content (TFC). The obtained results showed that non-conventional techniques delivered higher values of TPC and TFC than conve... [more]

Liquid concentration detection systems have been widely used in food, chemical, pharmaceutical, and many other industries. When the liquid flows, a large number of vortices will usually be generated, resulting in increased turbulence intensity, which will interfere with the detection of the concentration of the suspension. In this paper, a method for concentration detection by differential pressure based on turbulence elimination is proposed to improve the reliability of concentration detection results. The changes in the internal flow field corresponding to different lengths of the turbulence elimination structure and different inlet angles are analyzed through numerical simulation. Finally, the influence of changes in structure parameters on the accuracy of concentration detection is tested through experiments. The results show that when the length of the turbulence elimination structure is small, the vortex zone inside the concentration detection device changes with the inlet veloci... [more]

The need arises to seek new depuration technological responses aimed at the reuse of wastewater, which requires the development and promotion of economically and environmentally sustainable technologies. In this paper, it studies an improvement to a disinfection system sustainable, low-cost, patented in 2019, and based on solar energy. The water passes through a canal of reflective material in the continuous regime, and in the batch regime, the water remains in the canal. The panels are located parallel to the lateral faces of the canal. The fraction of the radiation reflected outside the canal reaches the reflective side panels that return the radiation to the canal. These panels concentrate the radiation in the canal through reflection. The disinfectant canal with fins and side panels uses ultraviolet radiation to eliminate the bacterial load carried by treated wastewater. For this reason, the present work analyzes the incidence in the area of influence of the disinfectant canal. Whe... [more]

Even in modern times, the popularity level of medicinal plants and herbal medicines in therapy is still high. The World Health Organization estimates that 80% of the population in developing countries uses these types of remedies. Even though herbal medicine products are usually perceived as low risk, their potential health risks should be carefully assessed. Several factors can cause the toxicity of herbal medicine products: plant components or metabolites with a toxic potential, adulteration, environmental pollutants (heavy metals, pesticides), or contamination of microorganisms (toxigenic fungi). Their correct evaluation is essential for the patient’s safety. The toxicity assessment of herbal medicine combines in vitro and in vivo methods, but in the past decades, several new techniques emerged besides conventional methods. The use of omics has become a valuable research tool for prediction and toxicity evaluation, while DNA sequencing can be used successfully to detect contaminants... [more]

In adhesive bonding, two different substrate materials are joined together, usually by forming chemical bonds. The adhesive can stick things together. The loading rate and deformation mode can easily change the mechanical properties of the adhesive material. Hence, a vital aim of the current study is to evaluate the strain rate effect on the damage response of adhesive joints for Mode I loading scenarios. The adherend material was aluminum AL6061-T6, and Araldite 2015 was the adherent material. This experiment for delamination had a prescribed adherend size of 200 mm × 25 mm × 3 mm and an adhesive thickness of 0.5 mm. In situations where the strain rate affects the failure mechanism, a displacement rate of 5, 50, or 500 mm/min is sufficient to attain the failure mechanism. A double cantilever beam (DCB) specimen was employed to construct the FE model geometry for simulation. A hybrid experimental−FE technique was utilized to extract the properties of the adhesive interface. FE simulati... [more]

A brushless direct current (BLDC) motor is a type of permanent magnet machine that is highly efficient and powerful and requires occasional maintenance. Thanks to these fortunate characteristics, this type of motor has various applications in high-tech industries. However, since BLDC motors are often required to operate at high-speed rotations and under extreme conditions, temperature overshoots can appear during operation, provoking damage to the windings. The purpose of this review is to present the results of a recent investigation and recollection of different methods used for the diagnosis of electrical faults in the stator, such as turn-to-turn short circuits, coil-to-coil short circuits, phase-to-phase short circuits and phase open circuits. In particular, this review presents an analysis of the available diagnosis methods according to the type of fault, the method or technique used for the diagnosis, the evaluated physical variables and the context in which the methods were eva... [more]

In this study, bacteria from the genus of Azotobacter, Bacillus and Pseudomonas were isolated from the roots of Phaseolus vulgaris and used as plant growth-promoting bacteria for Sinapis alba L., Brassica napus L., Amaranthus retroflexus L., Linum usitatissimum L., Panicum miliaceum L. and Rumex patientia L. plants. The results showed that all three bacteria had different effects on plants growth considering both sterile and non-sterile soil. Bacillus sp. induced the greatest influence in terms of the root length of Sinapis alba L. grown in sterile soil (with 28%), while considering non-sterile soil, Pseudomonas sp. increased the root and shoot length by 11.43% and 25.15%, respectively, compared to the blank sample. Azotobacter sp. exerted the highest beneficial influence on Brassica napus L. growth in non-sterile soil, since the root and shoot lengths were stimulated with 27.64% and 52.60%, respectively, compared to uninoculated plants. Bacillus sp. had a positive effect on the growth... [more]

This article was conducted within the framework of project reg. no. CZ.11.4.120/0.0/0.0/16_013/0002594, programme, Interreg V-A Czech Republic-Poland, Microprojects Fund 2014−2020 in the Euroregion Silesia. It is focused in the area of modelling technological processes and the presentation of the main principles of these models. The modelling of technological processes is important in terms of its applicability to process prediction in industry. A complex of analytical and predictive metallurgical models was developed within VSB-TUO. The original mathematical model of coke degradation in a blast furnace makes it possible to calculate the minimum consumption of coke from the dynamic balance for different values of the ratio of direct and indirect reduction. As part of the graphic output, it determines the practically and theoretically achievable minimum coke consumption points. The use of the model enables the determination of a real reserve in reducing the amount of coke.