With its unique qualities, such as infinite supply, high octane number, and capacity to cut greenhouse gas emissions, alcohol is a viable alternative fuel for SI engines. This review article aims to reveal to readers the effects of alcohol on the performance, combustion behavior, and emission characteristics of SI engines by collecting the outcomes from previous research. This article looks at methanol, ethanol, and butanol fuel qualities. The performance of SI engines with butanol, ethanol, and methanol combined with gasoline is investigated in terms of brake torque, brake power, fuel consumption, thermal efficiency, volumetric efficiency, mean effective pressure, and coefficient of variation under various conditions. Second, in-cylinder pressure, mass fraction burnt, ignition delay, pressure increases, and heat release rates are also used to evaluate the combustion characteristic. Finally, the article discusses pollutant emissions such as CO, CO2, NOx, UHC, and exhaust gas temperatur... [more]

The heat absorbed by the heat transfer fluid for cooling a concentrated photovoltaic thermal (CPVT) solar collector can be used for purposes such as residential heating and cooking. Because of the combined production of heat and power, these systems are proposed for individual or commercial use in rural areas. In this study, a hybrid system was proposed to increase the electrical efficiency of the system. Experiments were conducted in winter conditions. Two operational modes were compared, namely a CPVT system with HP (HP-CPVT) and without HP (CPVT). The evaporator of the heat pump was settled inside the triangular trough receiver. The effects of cooling the PV system with a heat pump in the bifacial CPVT system on the electrical and thermal energy efficiencies were investigated. The electricity and thermal energy efficiencies of the CPVT system were calculated as 12.54% and 38.37% in the HP-CPVT system, respectively, and 10.05% and 81.97% in the CPVT system, respectively. The electric... [more]

Despite being a limited and scarce resource, the necessity and exploitation of fossil fuels are unstoppable in serving human demands. In order to supply energy demand without causing environmental damage, it is crucial to utilize a variety of renewable feedstock resources. Biochar, made up mostly of carbon, oxygen, and hydrogen, is the product of the thermochemical processes of pyrolysis, hydrothermal carbonization, torrefaction, and hydrothermal liquefaction. Biochar, once activated, has the potential to act as a catalyst in a variety of energy generation processes, including transesterification and fermentation. Transesterification is the process that is used to produce biodiesel from a variety of oils, both edible and non-edible, as well as animal fats in the presence of either a homogeneous or a heterogeneous catalyst. When selecting a catalyst, the amount of free fatty acid (FFA) content in the oil is considered. Homogeneous catalysts are superior to heterogeneous catalysts becaus... [more]

The power system network grows yearly with a large number of nonlinear power generation systems. In this scenario, accurate modeling, control, and monitoring of interface systems and energy conversion systems are critical to the reliability and performance of the overall power system. In this trend, the permanent magnet synchronous generator (PMSG)-based wind turbine systems (WTS) equipped with a full-rated converter significantly contribute to the development of new and renewable energy generation. The various components and control systems involved in operating these systems introduce higher complexity, uncertainty, and highly nonlinear control challenges. To deal with this, state estimation remains an ideal and reliable procedure in the relevant control of the entire WTS. In essence, state estimation can be useful in control procedures, such as low-voltage ride-through operation, active power regulation, stator fault diagnosis, maximum power point tracking, and sensor faults, as it... [more]

Due to the rapid expansion of electric vehicles (EVs), they are expected to be one of the main contributors to transportation. The increasing use of fossil fuels as one of the most available energy sources has led to the emission of greenhouse gases, which will play a vital role in achieving a sustainable transportation system. Developed and developing countries have long-term plans and policies to use EVs instead of internal combustion vehicles and to use renewable energy to generate electricity, which increases the number of charging stations. Recently, to meet the charging demand for EVs, the main focus of researchers has been on smart charging solutions. In addition, maintaining power quality and peak demand for grids has become very difficult due to the widespread deployment of EVs as personal and commercial vehicles. This paper provides information on EV charging control that can be used to improve the design and implementation of charging station infrastructure. An in-depth anal... [more]

The monoclinic BiVO4 in a powder state was prepared via a hydrothermal method, with the addition of KCl as a structure-directing agent. The as-prepared sample was calcined at different temperatures (400−600 °C), either in the air or in Ar gas. It is found that, though the morphology and crystal structure mostly remain unchanged, the bandgap properties are modified during calcination. A detailed analysis of the surface chemical states and optical absorption properties reveals the involvement of tetravalent vanadium ions and oxygen vacancies as the cause of the band modification. The bandgap properties are to be found tunable via changing the calcination condition, as well as the KCl concentration in the precursor. The photocatalytic properties of BiVO4 samples are greatly enhanced with the addition of KCl in the precursor, but degraded by post-annealing, where the residual Cl in the calcined sample may act as an inhibitor. The enhanced photoactivity is explained in terms of favorable fa... [more]

With the global effort to reduce fossil fuels and to use eco-friendly energy, interest in Li-ion batteries (LIBs) is rapidly increasing. In the LIB system, the separator is an important component for determining the rate performance and safety of cells. Although polyolefin separators are commercially used in LIBs, they still suffer from inferior electrolyte wettability and low thermal stability issues. Here, we introduce a chemical surface modification for polyethylene (PE) separators using a poly(ether ether ketone) (PEEK) coating. The separators were pretreated in a tannic acid solution to enforce the adhesion of the coated layers. Then, PEEK was coated onto the PE surface by a doctor blading method. The separators were examined by infrared spectroscopy, and the surface properties were characterized by electrolyte uptake and contact angle measurements. The treated surface was hydrophilic, and the ionic conductivity of the cell with the modified separator was significantly improved. A... [more]

Ultracapacitors are energy storage devices that have shown outstanding capability in a vast spectrum of applications, mainly in energy storage systems required to deliver short bursts of electrical energy. Ultracapacitors possess high power density while batteries possess high energy density. In this paper, a hybrid energy storage device comprising a lithium-ion ultracapacitor module and a lead acid battery was modeled, built, and tested for vehicular start−stop application, which requires a much larger number of engine cranking events than conventional vehicles. The combination of a lead acid battery with Li-ion ultracapacitors was chosen due to the fact that the vast majority of vehicles utilize lead acid batteries to crank the internal combustion engine. This allows retrofitting this hybrid setup in conventional vehicles along with the start−stop feature without inflicting damage to the already installed lead acid battery. The start−stop feature puts high stress on the lead acid bat... [more]

The increased need for renewable energy systems to generate power, store energy, and connect energy storage devices with applications has become a major challenge. Energy storage using batteries is most appropriate for energy sources like solar, wind, etc. A non-isolated three-port DC−DC-converter energy conversion unit is implemented feeding the brushless DCmotor drive. In this paper, a non-isolated three-port converter is designed and simulated for battery energy storage, interfaced with an output drive. Based on the requirements, the power extracted from the solar panel during the daytime is used to charge the batteries through the three-port converter. The proposed three-port converter is analyzed in terms of operating principles and power flow. An FPGA-based NI LabView PXI with SbRio interface is used to develop the suggested approach’s control hardware, and prototype model results are obtained to test the proposed three-port converter control system’s effectiveness and practicali... [more]

An optical isolator circuit is developed to detect and dynamically relocate the photovoltaic (PV) module under partial shading. The suggested system control structure operates in two modes. Mode 1 governs the system at global maxima (GM) by tracing the power-voltage (PV) curve. Mode 2 detects and separates all the bypassed modules from a PV string/array by means of a decentralized control and stores its power in the battery. Simulations are performed on different shading patterns to verify the efficacy of the suggested system. The results showcase that the averaged harnessed power using the proposed circuit is 25.26% more than the total cross-tied (TCT) and series-parallel (SP) array configurations. The proposed circuit does not require complex gate driver circuits and large switch counts. The circuit is scalable and can be implemented on an “N × N” array.

The global energy and environmental crises are the most urgent issues confronting humanity in the coming years [...]

Worldwide energy shortages and the green energy revolution have triggered an increase in the penetration of standalone microgrids. However, they have limited generation capacity and are wasteful when excess generated energy is curtailed. This presents an opportunity for the coordinated operation of multiple prosumer microgrids that absorb this waste to enhance their resiliency and reliability. This paper proposes a reliable prosumer model with an inbuilt energy management system (EMS) simulator that considers the mentioned deficiencies for constructing resilient interconnected prosumer microgrids. The EMS simulator operates in a real-time dynamic environment to coordinate the prosumer components and performs flexible switching for (1) prioritizing critical load by shedding the non-critical load and (2) meeting load demand locally or from other interconnected prosumers. The EMS simulator maintains energy balance by setting limits for the battery energy storage system (BESS) to preserve... [more]

In this study, a power compensation control algorithm was designed and validated for commercial 100 kW medium wind turbine models for power compensation due to additional generator loss. Generally, torque control considering generator efficiency is applied to a controller of a medium wind turbine; however, a control corresponding to a decrease in generator efficiency due to the surrounding environment is not possible. There is a possibility that an additional generator loss may occur due to the surrounding environment of the wind turbine already installed, and accordingly, a power compensation control algorithm is required because power is expected to decrease. The power compensation control algorithms may be divided into three methods according to a control strategy, and three power compensation control algorithms were explained and designed. The proposed power compensation control algorithms were validated using DNV’s Bladed program. The simulation conditions were selected at an aver... [more]

Surface tension is a meaningful parameter influencing boiling and condensation in macroscopic scale, in confined spaces, or for nanofluids; it further affects boiling with surfactants. Surface, or interfacial, tension is an important property in the research into increasing heat transfer, enhancing efficiency of photovoltaic systems, improving engine operation, or forming drugs or polymers. It is often determined using axisymmetric drop shape analysis based on the differential equations system formulated by Bashforth and Adams. The closed-form expression of the interface shape states the radii defining the bubbles are the negative numbers, which causes the temperature profile drops along the heat transfer direction, e.g., in the Wiśniewski formulas for the temperature in the vapor bubbles; moreover, the drop, or bubble, possesses only one main radius of curvature, which may reduce the number of the unknowns and equations in the Bashforth and Adams algorithm. An alternative method apply... [more]

Here, laboratory tests were conducted to examine the effects of natural fracture density (NFD) on the propagation of hydraulic fracture (HF), HF and natural fracture (NF) interaction, and the formation of the stimulated reservoir volume (SRV). Laboratory methods were proposed to prepare samples with dense, medium and spare discrete orthogonal fracture networks. After conducting a true triaxial hydraulic fracturing experiment on the synthetic blocks, the experimental results were analyzed by qualitative failure morphology descriptions, and the quantitative analysis used two proposed new indices. On the pump pressure profiles, it reflected the non-linear interactions between HFs and NFs well. For rock blocks with a dense DFN density, pump pressure curves present fluctuation shape and the degree of interaction between HF and NF is strong; however, for model blocks with a sparse DFN density, the pump pressure curves present a sudden drop shape. In addition, different propagation behaviors... [more]

An agrovoltaic system combines agricultural crop production and energy production in the same place, emphasizing the dual use of land. This article provides a bibliometric analysis of agrivoltaic topics based on publications indexed in SCOPUS, in which either economic assessments of agrivoltaics, agrivoltaic systems for crops and livestock animals, photovoltaic greenhouse and agrivoltaics with open field are discussed, or its ideas are used to analyze certain locations. A bibliometric analysis was conducted using the SCOPUS database. Multiple bibliometric tools, such as R Studio and Biblioshiny, were applied to analyze data for this study. Finally, 121 relevant articles were obtained and reviewed. The results show that the focus topic is a brand-new research area, with the majority of relevant scientific publications concentrated in the last three years, and with much ongoing research. This is why AV-specialized scientific conferences might be the best place to get relevant and up-to-d... [more]

The article discusses the evaluation of potential heat production options for a large-scale district heating system in Narva (Estonia). Heat is currently generated at the Balti Power Plant’s CHP unit using local oil shale mixed with biomass. The CHP unit consists of two circulating fluidised bed boilers and a reheat steam turbine. According to the development strategy, the district heating system is expected to achieve carbon neutrality in the future. Various options and parameter variations should be analysed. The following scenarios were compared: (1) baseline scenario featuring an existing CHP extraction steam turbine; (2) alternative Scenario I featuring a CHP backpressure steam turbine; and (3) alternative Scenario II featuring a CHP gas turbine. To evaluate the above scenarios, a comprehensive energy/exergy analysis was performed, and economic indicators were calculated. The primary energy consumed, as well as the heat and electricity generated, were all taken into account. Based... [more]

In recent decades, many kinds of research have been conducted on alternative fuels for compression ignition (CI) engines. Low/zero-carbon fuels, such as bioalcohols and hydrogen, are the most promising alternative fuels and are extensively studied because of their availability, ease of manufacturing, and environmental benefits. Using these promising fuels in CI engines is environmentally and economically beneficial. The most common alcohols are methanol, ethanol, isopropanol, propanol, butanol, n-butanol, tert-butanol, iso-butanol, and pentanol. The primary objective of this review paper is to examine the impact of bioalcohols and their blends with conventional diesel fuel in CI engines since these fuels possess characteristic properties that impact overall engine performance and exhaust emissions. This research also indicated that alcohols and blended fuels could be used as fuels in compression ignition engines. Chemical and physical properties of alcohols were examined, such as lubri... [more]

The phenomenon of voltage asymmetry is common in electricity networks and is the cause of many unfavourable phenomena occurring, such as an increase in power and energy losses, as well as the abnormal operation of certain loads. Voltage asymmetry can be caused by several different factors, which include the design of the transmission line (e.g., routing of conductors in relation to each other and the earth), the parameters of consumer circuits (e.g., unequal loading of individual phases), or the design of network equipment (e.g., generators or transformers). An asymmetrical condition also occurs during system disturbances such as single-phase short circuits or lightning. One of the many factors impinging on voltage asymmetry in the electrical network is also the effect of load, but in the case of medium voltage power networks, this effect is neglected in the literature. This paper presents and evaluates the influence of the power consumed by consumers on the values of zero-voltage asym... [more]

In this work, a study was performed on the influence of the ratio of height to the diameter of the reduction zone of a small-size downdraft gasifier as well as of the fuel fraction sizes on the gas quality (the quality was evaluated for CO content). The ratio of a full side area to the volume of a fuel fraction (SVR) was used as a fuel parameter. The maximum CO concentration was observed when using a small fuel fraction with SVR—0.7−0.72 mm−1 and when adhering to the ratio of height to the diameter of the reduction zone H/D—0.5−0.6. The maximum electric power for gasoline generators (nominal power equaled 4 kW) when using the gas received from the fast-growing hybrid willow biomass equaled 2.4 kW. This power is 37.5% lower than when using gasoline and 7.0% lower than when using the gas received from the hardwood biomass. The emissions of harmful gases into the atmosphere by the gasoline generator engine equaled 0.12−0.14% CO and 24−27 mln−1 CxHy. The emissions were 64.8 times less... [more]

The electricity sector has been undergoing profound transformations. In particular, the Portuguese self-consumer regime has allowed customers of the medium and low voltage electricity grid to be producers/consumers of electricity, actively contributing to greater energy efficiency. In this context, the energy that comes from the sun is not used to its maximum. In addition, photovoltaic cells have a characteristic operating curve (voltage vs. current), in which any operating point is reflected. Within this curve, there is a particular point known as the maximum power point (MPP) at which the cell supplies the maximum power output to a load. If the cell does not operate at this point, it has lower efficiency values. To harness maximum power under standard and dynamic shading conditions, there are various techniques of low complexity for capturing maximum power. We present a maximum power point tracking (MPPT) algorithm capable of dealing with the problem of partial shading. This algorith... [more]

Environmentally friendly anaerobic digestion (AD) of lignocellulose-based materials is becoming an increasingly popular alternative to non-renewable energy sources. It also corresponds with the principles of sustainable development. The structure of lignocellulosic materials, which is resistant to biodegradation, requires using pretreatment methods prior to subjecting them to anaerobic processes. The aim of the study was to evaluate the influence of temperature and type of hydrolyzing agent on the efficiency of chemical pretreatment of sugar beet pulp. Biomass samples soaked in distilled water and 0.05 M solutions of NaOH and H2SO4 were left for 20 h, both at room temperature (22 °C) and in a thermostated chamber (50 °C). The changes in pH, electrolytic conductivity (EC), concentration of volatile fatty acids (VFA), dissolved chemical oxygen demand (COD), and phenols were analyzed. The concentration of CODdissolved, demonstrating the efficiency of pretreatment methods, obtained after a... [more]

Developing solar energy conversion devices is one key driver of the energy transition pathway [...]

Gas diffusion layers (GDLs) play a critical role in anion exchange membrane fuel cell (AEMFC) water management. In this work, the effect of GDL thickness on the cell performance of the AEMFC was experimentally investigated. Three GDLs with different thicknesses of 120, 260, and 310 µm (denoted as GDL-120, GDL-260, and GDL-310, respectively) were prepared and tested in a single H2/O2 AEMFC. The experimental results showed that the GDL-260 employed in both anode and cathode electrodes exhibited the best cell performance. There was a small difference in cell performance for GDL-260 and GDL-310, while water flooding was observed in the case of using GDL-120 operated at current densities greater than 1100 mA cm−2. In addition, it was found that the GDL thickness had more sensitivity to the AEMFC performance as used in the anode electrode rather than in the cathode electrode, indicating that water removal at the anode was more challenging than water supply at the cathode. The strategy of wat... [more]

This study investigates the enhancement of the rate of evaporation from a nanoengineered solid surface using non-equilibrium molecular dynamics simulation. Four different types of surface modifications were introduced to examine the thermal transportation behavior. The surface modification includes: (1) transformation of surface wetting condition from hydrophobic to hydrophilic, (2) implementing nanostructures on the smooth surface, (3) cutting nano slots on the smooth surface and (4) introducing nano-level surface roughness. Evaporation behavior from the same effective surface area was also studied. The simulation domain consisted of three distinct zones: solid base wall made of copper, a few layers of liquid argon, and a vapor zone made of argon. All the nano-level surface modifications were introduced on the solid base surface. The few layers of liquid argon representing the liquid zone of the domain take heat from the solid surface and get evaporated. Outside this solid and liquid... [more]