This paper presents a two-stage DC/DC converter with high efficiency utilized in an electronic power conditioner (EPC), which is widely applicable in satellite communications, etc. The galvanically isolated converter contains two cascaded converters: a buck converter, which is a pre-regulator operating under a closed-loop condition, and a push−pull converter, which is intended to boost the input voltage, operating under an open-loop condition. In the push−pull converter, the power switches, including the main switches and the rectifier diodes, operate under zero-voltage switching (ZVS) and zero-current switching (ZCS) at both switch off and switch on, which minimizes the switching loss. Furthermore, all of the parasitic parameters, such as the parasitic capacitance, leakage inductance, and magnetizing inductance of the main transformer, are fully utilized. Therefore, the presented topology benefits from fewer semiconductors but higher efficiency. The proposed topology produces less EMI... [more]

In this article, a theoretical mathematical model of gas flow through a duct in the case of local mass and momentum sources and sinks is presented. The continuity equation and motion equation with one-dimensional, density-stable gas flows were used to create this model. The size of sources and sinks and their locations have an effect on the size of gas stream flows in the duct, gas energy losses, and the parameters of the mechanical source energy that is causing the flow. In the traditional approach to describing the gas flow in the duct, the concept of resistivity and the equivalent resistance of the conduit is used. In the case of flow in the duct with local mass and momentum sources and sinks, the transport resistance depends on a bigger number of parameters than the concept of specific resistance usage. The location and size of the source flux or mass and momentum sinks and the fan work (suction, blowing) were taken into account in the presented model. The model gives the opportuni... [more]

The article deals with the issue of electromagnetic disturbances caused by electromechanical relays. Electromagnetic compatibility (EMC) is important for the reliable work of electrical and electronic devices. Our research focused on the low-voltage relay, which is the source of electrical fast transients (EFT)/burst disturbances. The voltage and current waveforms were tested on the constructed stand while opening the relays’ contacts. We investigated one-circuit topology with varied element parameters in order to observe their influence on the burst phenomenon. The new technologies in the measurement equipment allow us to observe many detailed aspects of the burst phenomenon, which were not reported up to now. In order to analyze the disturbances, they have been fragmented into restoration, ignition and arc times. The number of disturbance cycles differs depending on the value of the circuit capacitance on the load side. The effect of capacity on times of restoration, ignition and bur... [more]

Hydrogen adsorption measurements were taken by the weighting method using the Sartorius low-pressure microbalance. Experiments were conducted at two temperatures: 77.5 and 300 K; the adsorbent used was active carbon obtained from wood and modified with potassium hydroxide. The porous structure of the carbon prior to and after modification was evaluated based on the nitrogen adsorption and desorption data. Thus, the densimetric characteristic of active carbon was modified; porous structures were developed in the range of micro-, meso- and macropores and the volume of hydrogen adsorbed at 77.5 K showed an almost four-fold increase. Modified active carbons are found to be suitable for applications in hydrogen storage systems.

To solve the problem of rising energy use and CO2 emissions, China issued the 14th Five-Year Plan in 2020, emphasizing the need to reduce its carbon intensity and achieve a carbon emission peak before 2030. In order to estimate the future path of carbon peak in China, a novel dataset was constructed to analyze 30 provinces in China, and found that the realization of carbon peaking in 2025 requires a reduction of 1.072 million tons of carbon emissions in 2025, at which point peak carbon emissions will be 11,008.4 million tons. Due to this energy gap caused by carbon emission reduction the total amount of clean electricity has reached 3600 billion kWh. In carbon emission allowance trading, provinces with large carbon emissions, like Jiangsu and Guangdong, prefer to buy carbon allowances, while those with small carbon emissions like Shanxi and Inner Mongolia prefer to sell carbon allowances. In the energy trading market, the overall situation meets the 14th Five-Year Plan of west-east and... [more]

Due to the high acid, oxygen and water contents of fast pyrolysis oil, it requires the improvement of its fuel properties by further upgrading, such as catalytic hydrodeoxygenation (HDO). In this study, Nb2O5 was evaluated as a support of Pd-based catalysts for HDO of fast pyrolysis oil. A Pd/SiO2 catalyst was used as a reference. Additionally, the impact of iron as a promoter in two different loadings was investigated. The activity of the synthesized catalysts was evaluated in terms of H2 uptake and composition of the upgraded products (gas phase, upgraded oil and aqueous phase) through elemental analysis, Karl Fischer titration, GC-MS/FID and 1H-NMR. In comparison to SiO2, due to its acid sites, Nb2O5 enhanced the catalyst activity towards hydrogenolysis and hydrogenation, confirmed by the increased water formation during HDO and a higher content of hydrogen and aliphatic protons in the upgraded oil. Consequently, the upgraded oil with Nb2O5 had a lower average molecular weight and w... [more]

In this study, 3D premixed turbulent ammonia-hydrogen flames in air were studied using DNS. Mixtures with 75%, 50% and 25% ammonia (by mole fraction in the fuel mixture) and equivalence ratios of 0.8, 1.0 and 1.2 were studied. The studies were conducted in a decaying turbulence field with an initial Karlovitz number of 10. The flame structure and the influence of ammonia and the equivalence ratio were first studied. It was observed that the increase in equivalence ratio smoothened out the small scale wrinkles while leading to strongly curved leading edges. Increasing the amount of hydrogen in the fuel mixtures also led to increasingly distorted flames. These effects are attributed to local increases in the equivalence ratio due to the preferential diffusion effects of hydrogen. The effects of curvature on the flame chemistry were studied by looking at fuel consumption rates and key reactions. It was observed that the highly mobile H2 and H species were responsible for differential rate... [more]

This work investigated the influence of the reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed-bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi-pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed-bed reactor of 53 mL, without catalyst and using 5.0%, 7.5%, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Results show yields of bio-oil decreasing with increasing catalyst-to-tallow ratio. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics... [more]

In the context of smart electricity consumption, demand response is an important way to solve the problem of power supply and demand balance. Users participate in grid dispatching to obtain additional benefits, which realises a win-win situation between the grid and users. However, in actual dispatching, community users’ strong willingness to use energy leads to low enthusiasm of users to participate in demand response. Psychological research shows a direct connection between users’ herd mentality (HM) and their decision-making behavior. An optimal dispatching strategy based on user herd mentality is proposed to give full play to the active response-ability of community flexible load to participate in power grid dispatching. Considering that herd mentality is generated by the information interaction between users, by calling on some users to share the experience of successfully participating in demand response in the community information center and using the Nash social welfare functi... [more]

This study analyzed factors that influence the ignition delay characteristics of n-heptane/methane-blended fuel. The effects of chemical species, exhaust gas recirculation rate, compression ratio, cool/hot flames, and combustion chamber conditions (temperature, pressure, and O2 concentration) were determined and analyzed using CHEMKIN Pro. The experiment conditions for verification were 550−1000 K at 15 bar with 50% H2/50% CH4 fuel. The main combustion reactions were confirmed through reactivity analysis and sensitivity analysis on the ignition delay time. The ignition delay time at 14.7% O2 concentration was significantly higher than that at 21% O2 concentration by more than 30%. In addition, a higher ratio of methane in the blended fuel increased the ignition delay time as a result of methane dehydrogenation, delaying the ignition of heptane.

As the cooling requirement and the energy prices are increasing rapidly across the world, the need to develop highly efficient cooling equipment is rising as well. Adiabatic cooling employs evaporation to pre-cool the air flowing through a closed-loop coil. This study examines various adiabatic evaporative cooling pads in terms of their pre-cooling potential and advantages over currently available technological solutions through isolating three cross-sectional metal cooling pad shapes (W, Z and Z1). The results of the study suggest that the correlation between Δt↓ and RH↑ is somewhat close in all three cases; however, a slightly higher temperature drop is observed when using a W-shaped metal sheet. Pressure drop variability was negligible under current cooling pad configurations and experimental boundary conditions. Further studies focusing on measurement continuity, longevity and boundary conditions’ variability are recommended.

A new mathematical model was developed to predict the cylindrical effect of the membrane performance in the pressure retarded osmosis process. The cylindrical membrane transport layers (the draw side boundary and the porous membrane) were divided into very thin sublayers with constant mass transport parameters, among others with a constant radius in every sublayer. The obtained second-order differential mass balance equations were solved analytically, with constant parameters written for every sublayer. The algebraic equation system involving 2N equations was then solved for the determinant solution. It was shown that the membrane properties, water permeability (A), salt permeability (B), structural parameter (S) and the operating conditions (inlet draw side solute concentration and draw side mass transfer coefficient) affect the water flux strongly, and thus the membrane performance, due to the cylindrical effect caused by the variable surface and volume of the sublayers. This effect... [more]

A corresponding-states correlation for predicting the critical heat flux (CHF) in pool boiling conditions is proposed, and only requires knowledge of physical property constants of the fluid at any fluid temperature: molar mass, critical temperature, critical pressure, and the Pitzer acentric factor. If a fourth corresponding equation of state (EoS) parameter is added, a more accurate CHF correlation is obtained and matches Kutateladze−Zuber prediction within ±10% in the reduced temperature range of 0.55−0.95. This way, CHF can be easily predicted for any reduced temperature within the range of correlation’s validity by only knowing basic properties of the fluid. Additionally, two corresponding-states correlations for determining the capillary length are proposed and also do not rely on any temperature- and pressure-dependent fluid properties. A simpler correlation only using the Pitzer acentric factor is shown to be imprecise, and a more complex correlation also accounting for the fou... [more]

Seismic monitoring in areas where induced earthquakes could occur is a challenging topic for seismologists due to the generally very low signal to noise ratio. Therefore, the seismological community is devoting several efforts to the development of high-quality networks around the areas where fluid injection and storage and geothermal activities take place, also following the national induced seismicity monitoring guidelines. The use of advanced data mining strategies, such as template matching filters, auto-similarity search, and deep-learning approaches, has recently further fostered such monitoring, enhancing the seismic catalogs and lowering the magnitude of completeness of these areas. In this framework, we carried out an experiment where a small-aperture seismic array was installed within the dense seismic network used for monitoring the gas reservoir of Collalto, in North Italy. The continuous velocimetric data, acquired for 25 days, were analysed through the application of the... [more]

Organic Rankine cycles are often the best solution for the conversion of thermal energy. The many working fluids include silicon oils. One crucial issue that determines the choice of a working fluid is its thermochemical stability, as this sets a limit to the maximum temperature at which the fluid can be used in a power plant. A second subject, much debated today, is the use of mixtures in ORCs. In the first part of this study, an investigation into the thermal stability of siloxanes using two different approaches was carried out. The results confirmed a limit working temperature for the considered siloxanes of about 300 °C, with a degradation that advanced significantly over time at 350 °C. In the second part of the study, an analysis of the thermodynamic performances of some siloxane mixtures was carried out. It was found that the efficiencies of the corresponding thermodynamic cycles were substantially the same as for the pure fluids used today. By changing the composition of the mi... [more]

In Poland, there are low-temperature geothermal reservoirs that can be used for various purposes in many regions of the country. Low-temperature deposits of geothermal waters are common and occur much more frequently than high-temperature deposits. They contain water with temperatures lower than 150 °C. Their temperature normally ranges from 20 to 90 °C. Achieving a state of equilibrium depends on many factors, including the kinetics of reactions between the individual components of the system, temperature, reactivity of reservoir rock, concentration of chemical components in the water and the time the water remains in contact with the rock. Therefore, this article presents the possibility of checking the conditions of precipitation of inorganic sediments in geothermal waters with the use of PVT equipment. Tests were carried out with the use of geothermal waters under given dynamic conditions (pressure, temperature and flow). This paper confirms the suitability of using the equipment f... [more]

Electricity sector reforms have transformed the structure and organization of the sector worldwide. While outcomes of reforms in developed and developing countries have been extensively examined, there is limited analysis of the reforms in sub-Saharan Africa (SSA). This paper analyses the performance of electricity sector reforms in 37 SSA countries between 2000 and 2017. We use a stochastic frontier analysis approach to estimate a multi-input multi-output distance function to assess the impact of reform steps and institutional features on indicators of investment and technical efficiency. Results indicate a positive correlation between reforms and installed generation capacity per capita, plant load factor, and technical network losses. The presence of an electricity law, sector regulator, vertical unbundling, and private participation in the management of assets were positively correlated with reform performance. Perceptions of non-violent institutional features such as corruption, r... [more]

Social capital is currently perceived as one of the basic factors of economic development and economic success of enterprises. However, while there is already much research on social capital in enterprises, there has been little such research in the energy industry. The aim of the publication is to fill the gap in this regard. The basic question that the authors try to answer is whether there is a higher level of capital in energy companies compared to other industries, and if so, what the reasons are for this. Apart from answering this question, the authors present their own method of measuring the level of this capital. The first part of the article presents the results of a study on the level of social capital in Polish energy companies, whereas the second part compares the levels of social capital in energy companies and industrial companies in other sectors. According to the study, energy companies generally have higher levels of social capital than companies in other industries.... [more]

The results of experiments to determine the role of structural schemes for the ignition of a mechanically activated thermite mixture Al−CuO and the formation of its combustion flame are presented. The reaction initiated in the bulk of the experimental assembly transforms into torch combustion in an open space. The dynamics of the volume of the flame reaction region was determined. The stage of flame formation has a stochastic character, determined by the random distribution of the reaction centres in the initial volume of the components. A high-speed camera, a pyrometer and electro contact sensors were used as diagnostic tools. The ultimate goal of the study was to optimize the conditions for the flame formation of this mixture for its effective use with a single ignition of various gas emissions.

Innovative low-temperature disintegration (process temperature 55 °C and oxygen concentration 0.2 mg/dm3) can be an economically rational technology to intensifying energy production from renewable sources. The proposed process can achieve a degree of disintegration—under optimal conditions—of about 50%, which is excellent when compared with other methods of feed pre-treatment. The low-temperature disintegration of distillation residue and waste-activated sludge before the co-fermentation process increased biogas production by 30% and methane production by 65% (over a 26 d duration). The obtained results confirm that the low-temperature disintegration method can be effectively used to pre-prepare this type of feed. At the same time, it was discovered that the Gompertz model can be used to mathematically describe the biogas accumulation curves in the methane co-fermentation processes of the tested feeds (the correlation coefficients were higher than 0.98).

The aim of Energies’ Smart Cities and Urban Management Section is to present new research results and new proven practices aimed at optimizing the energy use of smart cities and improving the energy efficiency in urban management [...]

Due to water scarcity, in the last few decades, air-to-water generator (AWG) technology, whose useful effect is the extraction of water from air, has been improved. In particular, in the last few years, advanced AWG integrated systems have been developed. Such systems permit, not only to condense water from air, but also the smart use of the by-side effects of the process in order to partially or totally cover the heating ventilation air conditioning (HVAC) needs of a building. Presently, there are no evaluation tools that permit a complete comparison among AWG machines, taking into account all the useful effects that can be obtained at the same time and with the same energy input. The current work, starting from the need for such a tool, proposes a global index whose formulation considers all useful effects of an integrated system, the energy required to obtain them, and the integration degree of the machine. The index translates into a single number the system global efficiency, by m... [more]

In this study, a plucking-driven piezoelectric wave energy harvester (PDPWEH) consisted of a buoy, a gear train frequency up-conversion mechanism, and an array of piezoelectric cantilever beams was developed. The gear train frequency up-conversion mechanism with compact components included a rack, three gears, and a geared cam provide less energy loss to improve electrical output. Six individual piezoelectric composite beams were plucked by geared cam to generate electrical power in the array of piezoelectric cantilever beams. A sol-gel method was used to create the piezoelectric composite beams. To investigate PDPWEH, a mathematical model based on the Euler−Bernoulli beam theory was derived. The developed PDPWEH was tested in a wave flume. The wave heights were set to 100 and 75 mm, the wave periods were set to 1.0, 1.5, and 2.0 s. The maximum output voltage of the measured value was 12.4 V. The maximum RMS voltage was 5.01 V, which was measured by connecting to an external 200 kΩ res... [more]

The installation of base isolation systems in nuclear power plants can improve their safety from seismic loads. However, nuclear power plants with base isolation systems experience greater displacement as they handle seismic loads. The increase in relative displacement is caused by the installed base isolation systems, which increase the seismic risk of the interface piping system. It was found that the failure mode of the interface piping system was low-cycle fatigue failure accompanied by ratcheting, and the fittings (elbows and tees) failed due to the concentration of nonlinear behavior. Therefore, in this study, the limit state was defined as leakage, and an in-plane cyclic loading test was conducted in order to quantitatively express the failure criteria for the SCH40 6-inch carbon steel pipe elbow due to low-cycle fatigue failure. The leakage line and low-cycle fatigue curves of the SCH40 6-inch carbon steel pipe elbow were presented based on the test results. In addition, the li... [more]

The formula of engaging an energy service company (ESCO) in Poland is not a new form of accounting for investments in improving energy efficiency. The results of our survey confirm that many entities still lack sufficient knowledge about this subject. The research problem this paper is concerned with is the conditions of applying the ESCO formula (a model of investment financing with the participation of a specialised company) to support local government units and enterprises in energy-industry project development. For the purpose of this study, the research questions were formulated to analyse of the following issues: the reasons for interest in the ESCO formula and the sources of knowledge about this solution; activities and other factors that can increase or reduce interest in the ESCO formula; services in terms of ESCO formula implementation; the attractiveness of alternative instruments for financing energy industry projects, the benefits of using the ESCO formula and the influenc... [more]