The Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling engine powered by a moderate temperature source of heat. Obtained results enabled calibration of the evaluated theoretical model of the Stirling engine. The model of the engine has been subsequently used for the analysis of regenerator effectiveness influenced by the charge pressure and the heating temperature. Performed study allowed to determine further development directions of the prototype engine to improve its power and efficiency. As a result of optimization, worked out design will potentially increase the indicated efficiency up to 19.5% (5.5% prototyp... [more]

In this paper, a dual-stage modeling and optimization framework has been developed to obtain an optimal combination and size of wayside energy storage systems (WESSs) for application in DC rail transportation. Energy storage technologies may consist of a standalone battery, a standalone supercapacitor, a standalone flywheel, or a combination of these. Results from the dual-stage modeling and optimization process have been utilized for deducing an application-specific composition of type and size of the WESSs. These applications consist of different percentages of energy saving due to regenerative braking, voltage regulation, peak demand reduction, estimated payback period, and system resiliency. In the first stage, sizes of the ESSs have been estimated using developed detailed mathematical models, and optimized using the Genetic Algorithm (GA). In the second stage, the respective sizes of ESSs are simulated by developing an all-inclusive model of the transit system, ESS and ESS managem... [more]

The short-term variability of photovoltaic (PV) system-generated power due to ambient conditions, such as passing clouds, represents a key challenge for network planners and operators. Such variability can be reduced using a geographical smoothing technique based on installing multiple PV systems over certain locations at distances of meters to kilometers. To accurately estimate the PV system’s generated power during cloud events, a variability reduction index (VRI), which is a function of several parameters, should be calculated precisely. In this paper, the Wavelet Transform Technique (WTT) along with Adaptive Neuro Fuzzy Inference System (ANFIS) are used to develop new models to estimate the PV system’s power output during cloud events. In this context, irradiance data collected from one PV system along with other parameters, including ambient conditions, were used to develop the proposed models. Ultimately, the models were validated through their application on a 0.7 km2 PV plant w... [more]

As application of electric energy have expanded, the uninterruptible power supply (UPS) concept has attracted considerable attention, and new UPS technologies have been developed. Despite the extensive research on the batteries for UPS, conventional batteries are still being used in large-scale UPS systems. However, lead-acid batteries, which are currently widely adopted in UPS, require frequent maintenance and are relatively expensive as compared with some other kinds of batteries, like metal-air batteries. In previous work, we designed a novel metal-air battery, with low cost and easy maintenance for large-scale UPS applications. An extensive analysis was performed to apply our metal-air battery to the hybrid UPS model. In this study, we focus on including an optimal control system for high battery performance. We developed an algorithm based on receding horizon control (RHC) for each fan of the cooling system. The algorithm reflects the operation properties of the metal-air battery... [more]

Optimal upscaling of a high-resolution static geologic model that reflects the flow performance of the reservoir is important for reasons such as time and calculation efficiency. In this study, we demonstrate that honoring reservoir heterogeneity is critical in predicting accurate production and reducing the time and cost of running reservoir flow simulations for the Hunton Group carbonate. We integrated three-dimensional (3D) seismic data, well logs, thin sections, outcrops, multiscale fracture studies, discrete fracture networks, and geostatistical methods to create a 100 × 150 × 1 ft gridded representative geologic model. We calibrated our gridded porosity and permeability parameters, including the evaluation of fractures, by history matching the simulated production rate and cumulative production volumes from a baseline fine-scale model generated from petrophysical and production data obtained from five wells. We subsequently reperformed the simulations using a suite of coarser gri... [more]

Hydrogen presents an attractive option to decarbonise the present energy system. Hydrogen can extend the usage of the existing gas infrastructure with low-cost energy storability and flexibility. Excess electricity generated by renewables can be converted into hydrogen. In this paper, a novel multi-energy systems optimisation model was proposed to maximise investment and operating synergy in the electricity, heating, and transport sectors, considering the integration of a hydrogen system to minimise the overall costs. The model considers two hydrogen production processes: (i) gas-to-gas (G2G) with carbon capture and storage (CCS), and (ii) power-to-gas (P2G). The proposed model was applied in a future Great Britain (GB) system. Through a comparison with the system without hydrogen, the results showed that the G2G process could reduce £3.9 bn/year, and that the P2G process could bring £2.1 bn/year in cost-savings under a 30 Mt carbon target. The results also demonstrate the system impli... [more]

The quality or reliability of diagnostics is understood as obtaining the most likely diagnosis, and finding possible causes leading to incorrect operation of the system. In real engine running conditions it is often very difficult. Dependable methods providing the most reliable diagnoses have not been developed yet. It becomes more and more important to identify the limit state in condition monitoring—the state that should not be exceeded because continued operation of such a machine is not advisable for technical, economic, or operational safety reasons. The authors have implemented a method using acoustic emission signal analysis for the identification of the injection pump limit state in a working engine. The use of the cross gain function allows one to reliably diagnose limit conditions related to the wear of the precision pair in injection pumps of running engines, working as energy transmission systems on ships and in land-based power stations. The paper draws the results for two... [more]

LiNixCoyMnzO2 (LNCM)-layered materials are considered the most promising cathode for high-energy lithium ion batteries, but suffer from poor rate capability and short lifecycle. In addition, the LiNi1/3Co1/3Mn1/3O2 (NCM 111) is considered one of the most widely used LNCM cathodes because of its high energy density and good safety. Herein, a kind of NCM 111 with semi-closed structure was designed by controlling the amount of urea, which possesses high rate capability and long lifespan, exhibiting 140.9 mAh·g−1 at 0.85 A·g−1 and 114.3 mAh·g−1 at 1.70 A·g−1, respectively. The semi-closed structure is conducive to the infiltration of electrolytes and fast lithium ion-transfer inside the electrode material, thus improving the rate performance of the battery. Our work may provide an effective strategy for designing layered-cathode materials with high rate capability.

The ability to predict wind speeds is very important for the security and stability of wind farms and power system operations. Wind speeds typically vary slowly over time, which makes them difficult to forecast. In this study, a hybrid nonlinear estimation approach combining Gaussian process (GP) and unscented Kalman filter (UKF) is proposed to predict dynamic changes of wind speed and improve forecasting accuracy. The proposed approach can provide both point and interval predictions for wind speed. Firstly, the GP method is established as the nonlinear transition function of a state space model, and the covariance obtained from the GP predictive model is used as the process noise. Secondly, UKF is used to solve the state space model and update the initial prediction of short-term wind speed. The proposed hybrid approach can adjust dynamically in conjunction with the distribution changes. In order to evaluate the performance of the proposed hybrid approach, the persistence model, GP mo... [more]

Innovations in technical, financial, and social areas are crucial prerequisites for an effective and sustainable energy transition. In this context, the construction of a new energy structure and the motivation of the consumer towards a change in their consumption behaviours to balance demand with a volatile energy supply are important issues. At the same time, Consumer Stock Ownership Plans (CSOPs) in renewable energies sources (RESs) have proven to be an essential cornerstone in the overall success of energy transition. Indeed, when consumers acquire ownership in RES, they become prosumers, participating in the phase of production and distribution of energy. Prosumers provide benefits by (1) generating a part of the energy they consume, (2) reducing their overall expenditure for energy, and (3) receiving a second source of income from the sale of excess production. Supporting Consumer Co-Ownership in Renewable Energies (SCORE) is an ongoing Horizon 2020 project with the aim of overco... [more]

In Liquid Rocket Engines, higher combustion efficiencies come at the cost of the propellants exceeding their critical point conditions and entering the supercritical domain. The term fluid is used because, under these conditions, there is no longer a clear distinction between a liquid and a gas phase. The non-conventional behavior of thermophysical properties makes the modeling of supercritical fluid flows a most challenging task. In the present work, a Reynolds Averaged Navier Stokes (RANS) computational method following an incompressible but variable density approach is devised on which the performance of several turbulence models is compared in conjunction with a high accuracy multi-parameter equation of state. In addition, a suitable methodology to describe transport properties accounting for dense fluid corrections is applied. The results are validated against experimental data, making it clear that there is no trend between turbulence model complexity and the quality of the produ... [more]

The fully printable carbon triple-mesoscopic perovskite solar cell (C-PSC) has already demonstrated good efficiency and long-term stability, opening the possibility of lab-to-fab transition. Modules based on C-PSC architecture have been reported and, at present, are achieved through the accurate registration of each of the patterned layers using screen-printing. Modules based on this approach were reported with geometric fill factor (g-FF) as high as 70%. Another approach to create the interconnects, the so-called scribing method, was reported to achieve more than 90% g-FF for architectures based on evaporated metal contacts, i.e., without a carbon counter electrode. Here, for the first time, we adopt the scribing method to selectively remove materials within a C-PSC. This approach allowed a deep and selective scribe to open an aperture from the transparent electrode through all the layers, including the blocking layer, enabling a direct contact between the electrodes in the interconne... [more]

Power system inertia is a vital part of power system stability. The inertia response within the first seconds after a power imbalance reduces the velocity of which the grid frequency changes. At present, large shares of power system inertia are provided by synchronously rotating masses of conventional power plants. A minor part of power system inertia is supplied by power consumers. The energy system transformation results in an overall decreasing amount of power system inertia. Hence, inertia has to be provided synthetically in future power systems. In depth knowledge about the amount of inertia provided by power consumers is very important for a future application of units supplying synthetic inertia. It strongly promotes the technical efficiency and cost effective application. A blackout in the city of Flensburg allows for a detailed research on the inertia contribution from power consumers. Therefore, power consumer categories are introduced and the inertia contribution is calculat... [more]

A low temperature environment will lead to the decrease of chemistry reaction rate and increase of the internal resistance of the lithium battery. In addition, the excessive charging current will cause the lithium to separate out and even the permanent attenuation of battery capacity. In order to solve these problems, this paper proposes a low-temperature charging heating combined control strategy, which takes the temperature acceptable charging current of the battery at low temperature as the charging current constraint and the maximum output power of the system as the power constraint. Firstly, a scheme of combined charging and heating control system is put forward. Secondly, the low temperature charging control strategy based on adaptive fuzzy control is established and then the model is simulated and analyzed in MATLAB software. At last, a Chroma 72,001 charge and discharge tester is used to conduct a low temperature test on 18,650 lithium iron phosphate battery monomers. The resul... [more]

Renewable energy systems and electric vehicles (EVs) are receiving much attention in industrial and scholarly communities owing to their roles in reducing pollutant emissions. Integrated energy systems (IES), which connect different types of renewable energies and storages, have become common in many applications, such as the grid-connected photovoltaic (PV) and battery systems, fuel cells and battery/supercapacitor in EVs. The advantages of all energy sources are maximized by utilizing connection and control strategies. Because many storage systems and household loads are mainly direct current (DC) types, the DC grid has considerable potential for increasing the efficiency of distribution grids in the future. In IES and future DC grid systems, the triple active bridge (TAB) converter is an isolated bidirectional DC-DC converter that has many advantages as a core circuit. Therefore, this paper reviews the characteristics of the TAB converter in current applications and suggests next-ge... [more]

In cereal crops, chaff is a valuable lignocellulosic by-product that accounts for more than 50 Mt y−1 in Europe and is suitable for bioenergy purposes. Chaff is usually not collected due to the lack of combine harvesters that have the capability to handle it properly. The present two years experimental study investigated the hypothesis that the overall biomass collected in wheat crop can be increased by equipping the combine harvester with an aftermarket device. Chaff, discharged from the combine harvester-cleaning system, is collected by the turbine that delivers it either on the swath or on a lateral trailer towed by a tractor. The performance of all machines involved in the harvesting (combine harvester, tractor, baler, and trailer) were assessed. The chaff was collected in bales with the straw (A mode) and separately on a trailer (C mode). Comparisons with non-collected treatment (B mode) were performed in order to estimate the total chaff collected and the biomass losses. The resu... [more]

Upward migration of gas-dissolved pore fluid is an important mechanism for many naturally occurring hydrate reservoirs. However, there is limited understanding in this scenario of hydrate formation in sediments. In this preliminary work, hydrate formation and accumulation from dissolved gas in sandy sediments along the migration direction of brine was investigated using a visual hydrate simulator. Visual observation was employed to capture the morphology of hydrates in pores through three sapphire tubes. Meanwhile, the resistivity evolution of sediments was detected to characterize hydrate distribution in sediments. It was observed that hydrates initially formed as a thin film or dispersed crystals and then became a turbid colloidal solution. With hydrate growth, the colloidal solution converted to massive solid hydrates. Electrical resistivity experienced a three-stage evolution process corresponding to the three observed hydrate morphologies. The results of resistivity analysis also... [more]

This paper presents an attempt to the valuation of the operational flexibility of the energy investment project based on the example of combined cycle gas turbine (CCGT). For this purpose, the real options approach (ROA), net present value (NPV) method, and the Monte Carlo (MC) simulation have been used. Motivations to take up such a topic result from the fact that traditional valuation methods neglect flexibility embedded in CCGT assets. Operational flexibility was defined as the switching option to dynamically shut down and restart gas units. Valuation of the operational flexibility, the project’s extended net present value (XNPV), was based on a discounted cash flow model. The Monte Carlo simulation, allowing for better replication of the stochastic nature of market factors and some technical parameters, was introduced to the valuation model. The obtained results indicate that the value of the options significantly influences the NPV of the analyzed technology and its risk profile.... [more]

Automobile exhaust heat recovery is considered to be an effective means to enhance fuel utilization. The catalytic production of hydrogen by methanol steam reforming is an attractive option for onboard mobile applications, due to its many advantages. However, the reformers of conventional packed bed type suffer from axial temperature gradients and cold spots resulting from severe limitations of mass and heat transfer. These disadvantages limit reformers to a low efficiency of catalyst utilization. A novel rib microreactor was designed for the hydrogen production from methanol steam reforming heated by automobile exhaust, and the effect of inlet exhaust and methanol steam on reactor performance was numerically analyzed in detail, with computational fluid dynamics. The results showed that the best operating parameters were the counter flow, water-to-alcohol (W/A) of 1.3, exhaust inlet velocity of 1.1 m/s, and exhaust inlet temperature of 773 K, when the inlet velocity and inlet temperatu... [more]

To investigate the aerodynamic performance of exhaust passage under multi-phase flow, an actual case is conducted in the low-pressure double exhaust passages of 600 MW steam turbine. Then, the flow field is compared and analyzed with and without the built-in extraction pipelines based on the Eulerian−Eulerian homogenous medium multiphase method. Results show that the upstream swirling flow and downstream mixed swirling flow are the main causes to induce the entropy-increase in the exhaust passage. Moreover, the flow loss and static-pressure recovery ability in the exhaust hood are greater than those in the condenser neck. Compared with the flow field without the steam extraction pipelines, the entropy-increase increases, the static pressure recovery coefficient decreases, and the spontaneous condensation rates of wet steam decrease in the downstream area of the pipelines. With the increase of steam turbine loads, an increment in entropy-increase in the exhaust passage is 0.98 J/(kg·K)... [more]

The three-temperature frost-free refrigerator is popular in China currently, which adopts a single evaporator and separate air ducts to distribute cold air into all compartments, i.e., the fresh food compartment (FFC), the variable temperature compartment (VTC), and the freezer compartment (FZC). Two identical refrigerators with cyclopentane insulation are comparatively studied in this article, one with vacuum insulation panels (VIPs) in two sidewalls and the other without. Results show that VIPs reduce the steady-state energy consumption of the refrigerator by 12.4% due to smaller average power input and longer compressor-off duration. The decrease in average power input originates from a shorter FFC-damper-on duration since VIPs reduce its thermal load. However, the FFC average temperature rises unexpectedly with shorter damper-on and longer damper-off durations, and induces thermal load transfer from FFC to FZC through the mixing of return air in the evaporator chamber. Consequently... [more]

As a result of the lattice mismatch between the oxide itself and the substrate, the high-pressure structural properties of trivalent rare earth (RE)-doped ceria systems help to mimic the compressive/tensile strain in oxide thin films. The high-pressure structural features of Sm-doped ceria were studied by X-ray diffraction experiments performed on Ce1−xSmO2−x/2 (x = 0.2, 0.3, 0.4, 0.5, 0.6) up to 7 GPa, and the cell volumes were fitted by the third order Vinet equation of state (EoS) at the different pressures obtained from Rietveld refinements. A linear decrease of the ln B 0 vs. ln ( 2 V a t ) trend occurred as expected, but the regression line was much steeper than predicted for oxides, most probably due to the effect of oxygen vacancies arising from charge compensation, which limits the increase of the mean atomic volume ( V a t ) vs. the Sm content. The presence of RE2O3-based cubic microdomains within the sample stiffens the whole structure, ma... [more]

Conventional multilevel inverter topologies like neutral point clamped (NPC), flying capacitor (FC), and cascade H bridge (CHB) are employed in the industry but require a large number of switches and passive and active components for the generation of a higher number of voltage levels. Consequently, the cost and complexity of the inverter increases. In this work, the basic unit of a switched capacitor topology was generalized utilizing a cascaded H-bridge structure for realizing a switched-capacitor multilevel inverter (SCMLI). The proposed generalized MLI can generate a significant number of output voltage levels with a lower number of components. The operation of symmetric and asymmetric configurations was shown with 13 and 31 level output voltage generation, respectively. Self-capacitor voltage balancing and boosting capability are the key features of the proposed SCMLI structure. The nearest level control modulation scheme was employed for controlling and regulating the output volt... [more]

Solid-state photon-enhanced thermionic emission (PETE) solar energy converters are newly proposed devices that can directly convert solar energy into electrical power at high temperatures. An analytical model based on a one-dimensional steady-state equation is developed to analyze the temperature-dependent performance of the solid-state PETE converter. The treatment used to derive the reverse saturation current density ( J 0 ) and open-circuit voltage ( V o c ) of the solid-state PETE converter is similar to that used in photovoltaic cells. Thus, their performances at elevated temperatures can be compared. Analysis results show that J 0 of the solid-state PETE converter with a GaAs absorption layer is approximately three orders of magnitude lower, and the decrease rate of open-circuit voltage ( − d V o c / d T ) is smaller than that of a practical GaAs photovoltaic cell. The improved performance of the solid-state PETE converter at high temperature... [more]

Increasing maintenance costs will hinder the expansion of the wind power industry in the coming decades. Training personnel, field maintenance, and frequent boat or helicopter visits to wind turbines (WTs) is becoming a large cost. One reason for this cost is the routine turbine inspection repair and other stochastic maintenance necessitated by increasingly unbalanced figure loads and unequal turbine fatigue distribution in large-scale offshore wind farms (OWFs). In order to solve the problems of unbalanced fatigue loads and unequal turbine fatigue distribution, thereby cutting the maintenance cost, this study analyzes the disadvantages of conventional turbine fatigue definitions. We propose an improved fatigue definition that simultaneously considers the mean wind speed, wind wake turbulence, and electric power generation. Further, based on timed automata theory, a power dispatch approach is proposed to balance the fatigue loads on turbines in a wind farm. A control topology is constr... [more]