This paper proposes a novel high voltage conversion gain DC/DC boost converter for renewable energy applications and systems. The proposed converter utilizes a three-winding coupled inductor. The presented converter benefits from a unique advantage, as the actual turn ratio of the coupled inductor is decreased in the charging state of the coupled inductor. However, while the inductor is discharging, the actual turn ratio is increased. This feature leads to a very high voltage conversion gain. Furthermore, a passive clamp circuit is employed to recover the leakage current of the coupled inductor. The voltage stresses on the semiconductors are also reduced. In addition, the average current of the primary side of the coupled inductor is zero. This will reduce the total energy stored in the passive elements of the converter. The paper analyzes the Continuous Conduction Mode (CCM) and the operation principles of the presented converter are thoroughly derived. A 250 W laboratory hardware pro... [more]

The increasing penetration of variable renewable energies (VRE) in the European electricity mix requires flexible energy storage systems (ESS), such as pumped storage hydropower (PSH). Disused mining voids from deep closed mines may be used as subsurface reservoirs of underground pumped-storage hydropower (UPSH) plants. Unlike conventional PSH plants, the air pressure in UPSH plants is variable and it differs from the atmospheric conditions. In this paper, the hydraulic transient process of an UPSH plant operating in pumping mode was investigated and a preliminary thermodynamic analysis of the closed surge tank was carried out. Analytical and CFD three-dimensional numerical simulations based on the volume of fluid (VOF) model with two-phase flow have been performed for analyzing the transient process. In the transient simulation, air and water are considered as ideal gas and compressible liquid, respectively. Different guide vanes closing schemes have been simulated. The obtained resul... [more]

The Ukrainian energy sector is one of the most inflexible energy sectors in the world as a result of the almost complete depreciation of the equipment of the main sources of power supply: nuclear, thermal, and hydropower. In connection with existing problems, there is a need to develop and use new energy-saving technologies based on renewable energy sources. In this proposed research, a regression model of renewable energy growth in the energy sector of Ukraine was developed. The studied literature reveals that the independent use of individual functioning elements of renewable energy sources function as the primary power source that is not an optimal solution for stable energy supply. This study proposes the use of hybrid renewable energy systems, namely a combination of two or more renewable energy sources that will help each other to achieve higher energy efficiency, accelerate the growth of renewable energy in the share of the Ukrainian energy sector and/or improve functioning with... [more]

Trash racks are the first element mounted in inlet channels of hydraulic structures. Their primary task is to capture coarse pollutants flowing in the riverbed/river channel and protect water facilities downstream. With the use of these devices, it is possible to separate coarse suspended matter, branches carried with the current, floating plastic elements, etc., which undoubtedly contributes to a trouble-free flow through culverts or channels and prevents hydroelectric power plant turbines from failure. An important issue here is also to ensure the proper operation of trash racks, particularly in respect of hydraulic structures whose task is to convert water energy into electricity (hydropower plants). Proper operation of trash racks minimizes losses arising from obstructing the free flow of water through accumulated waste or, in the wintertime, through icing. Incorrect work in this area entails specific head losses, and consequently leads to economic harm. In the paper, the resistanc... [more]

This study examines how the energy renovation of old detached houses affects the hourly power consumption of heating and electricity in Finland. As electrification of heating through heat pumps becomes more common, the effects on the grid need to be quantified. Increased fluctuation and peak power demand could increase the need for fossil-based peaking power plants or call for new investments to the distribution infrastructure. The novelty in this study is the focus on hourly power demand instead of just annual energy consumption. Identifying the influence of building energy retrofits on the instantaneous power demand can help guide policy and investments into building retrofits and related technology. The work was done through dynamic building simulation and utilized building configurations obtained through multi-objective optimization. Deep energy retrofits decreased both the total and peak heating power consumption. However, the use of air-source heat pumps increased the peak power... [more]

In order to reveal the gas−water distribution and formation mechanism of the low-permeability sandstone gas reservoir, the gas reservoir distribution and the formation mechanism in a low-permeability sandstone gas reservoir are investigated using data obtained from a physical simulation experiment of gas percolation. The exploration and experimenting for petroleum in the upper Paleozoic gas pool of the Sulige gas field in the Ordos basin in this paper. Results showed that the gas reservoir is characterized by low gas saturation, a complex distribution relationship of gas−water, and weak gas−water gravity differentiation. The characteristics of gas distribution are closely related to permeability, gas flow, and migration force. The capillary pressure difference is the main driving force of gas accumulation. There exists a threshold pressure gradient as gas flows in low-permeability sandstone. The lower that permeability, the greater the threshold pressure gradient. When the driving forc... [more]

Biodiesel is a proven alternative fuel that can serve as a substitute for petroleum diesel due to its renewability, non-toxicity, sulphur-free nature and superior lubricity. Waste-based non-edible oils are studied as potential biodiesel feedstocks owing to the focus on the valorisation of waste products. Instead of being treated as municipal waste, waste coffee grounds (WCG) can be utilised for oil extraction, thereby recovering an energy source in the form of biodiesel. This study evaluates oil extraction from WCG using ultrasonic and Soxhlet techniques, followed by biodiesel conversion using an ultrasonic-assisted transesterification process. It was found that n-hexane was the most effective solvent for the oil extraction process and ultrasonic-assisted technology offers a 13.5% higher yield compared to the conventional Soxhlet extraction process. Solid-to-solvent ratio and extraction time of the oil extraction process from the dried waste coffee grounds (DWCG) after the brewing proc... [more]

Selecting an appropriate contract price between electric vehicle aggregators and electric vehicle owners is an uncertain, multi-criteria decision-making issue. In addition, the results can cause strong conflict due to different aims: the optimal value for increasing electric vehicle aggregator (EVA) profit negatively affects the cost for owners. The value of the contract price can change the optimal scheduling of EVAs in the day-ahead market. Taking into consideration this context, the current paper proposes to solve the multi-objective scheduling problem of an aggregator with a goal programming approach. The presented approach sets a satisfaction level for each goal according to decision-makers’ preference. Numerical results illustrate the validity of this approach to balance different performance measures. Furthermore, optimal scheduling of electric vehicle aggregators in the day-ahead market is created.

Exact component characteristics are required for establishing an accurate component level aeroengine model. When component characteristics is lacking, the dynamic coefficient method based on test data, is suitable for establishing a single-input and single-output aeroengine model. When it is applied to build multiple-input, multiple-output aeroengine models, some parameters are assumed to be unchanged, which causes large error. An improved modeling method based on rig data is proposed to establish a double-input, double-output model for a micro variable-pitch turboprop engine. The input variables are fuel flow and pitch angle, and the output variables are rotational speeds of the core engine and the propeller. First, in order to gather modeling data, a test bench is designed and rig tests are carried out. Then, two conclusions are obtained by analyzing the rig data, based on which, the power turbine output is taken as the function of the core speed and the propeller speed. The establis... [more]

Salinity gradient resource presents an essential role for power generated in the process of pressure-retarded osmosis (PRO). Researchers proposed several designs for coupling the PRO process with the desalination plants, particularly reverse osmosis technology for low-cost desalination but there is no study available yet on the utilization of the concentrated brine reject from a thermal desalination plant. This study evaluates the feasibility of power generation in the PRO process using thermal plant brine reject-tertiary sewage effluent (TSE) salinity gradient resource. Power generation in the PRO process was determined for several commercially available FO membranes. Water flux in Oasys Forward Osmosis membrane was more than 31 L/m2h while the average water flux in the Oasys module was 17 L/m2h. The specific power generation was higher in the thin film composite (TFC) membranes compared to the cellulose triacetate (CTA) membranes. The specific power generation for the Oasys membrane... [more]

Health impacts and a decrease in the quality of life caused by air pollution is a major problem worldwide. Krakow is one of the most affected cities in the EU by air pollution mostly caused by burning solid fuels in households’ furnaces. It is considered that the most effective remedies would be adequate spatial planning solutions and application of low-emission sources including renewable energy sources (RES). This article draws from the analysis of the use of RES as a means for reducing harmful emissions in Krakow Functional Area (KrOF). The inventories of renewable energy sources and systems were compiled by the authors as a part of the EU project “Smart Edge—Sustainable Metropolitan Areas and the Role of The Edge City”. Using the data from the inventories, a SWOT analysis has been carried out to identify factors that determine the smart management of the RES potential, particularly the decisions of households on the transition towards RES. The results of the analysis have shown tha... [more]

We propose an integrated geothermal system that consists of air-conditioning and hot water service ground source heat pumps, both of which share a ground water loop. The proposed system increases the COP of the service hot water ground source heat pump by recovering the condensation heat of the air-conditioning ground source heat pump as an evaporator heat source for the hot water service ground source heat pump. Eventually this integration expands the scope and capacity of the evaporator source in addition to the underground water of heat exchangers, which also leads to increase the COP of the air-conditioning ground source heat pump. The integrated geothermal heat pump system was installed in a hotel, and then data were measured for a limited period due to the hotel’s ongoing business activities. A TRNSYS simulation model has been developed as a baseline, and the baseline has been calibrated with the measured data. By running one-year simulations, it turns out that the annual electri... [more]

Under the adverse trend of fossil energy attenuation and air pollution, wind power effectively alleviates the global energy crisis and environmental pollution. For wind turbines, especially large offshore wind turbines, their transportation, installation, and maintenance are very inconvenient. In order to solve this problem, this paper presents an E-core stator modular machine which inserts stator gap into the unwounded teeth of the fractional-slot concentrated winding (FSCW) permanent magnet (PM) machine. The winding factor of the new stator structure machine was derived. The electromagnetic models of 12-slot/10-pole and 12-slot/14-pole modular FSCW PM machines and traditional FSCW PM machines were established using the finite element analysis (FEA) software, and the open-circuit flux density, cogging torque, load torque, loss, and efficiency were simulated and analyzed. The results showed that the modular structure of E-core stator not only simplified the transportation, installation... [more]

This paper presents the laboratory test stand that is used for experimental validation of underground power cable system models. Determination of temperature distribution in the vicinity of the cable is the main goal of the study. The paper considers a system of three power cables, situated in the in-line arrangement, and buried in sand. Three electrical heaters of special construction are used in order to simulate the heat flux that is generated in the power cables during their operation. The test stand is designed to be placed in a thermoclimatic chamber, which allows testing the system in various thermal conditions when the ambient temperature changes by 20 °C to 30 °C. Numerical computations of the steady-state temperature fields are performed using the finite element method.

This paper investigates the energy management system (EMS) of a conventional autonomous vehicle, with a view to enhance its powertrain efficiency. The designed EMS includes two neuro-fuzzy (NF) systems to produce the optimal torque of the engine. This control system uses the dynamic road power demand of the autonomous vehicle as an input, and a PID controller to regulate the air mass flow rate into the cylinder by changing the throttle angle. Two NF systems were trained by the Grid Partition (GP) and the Subtractive Clustering (SC) methods. The simulation results show that the proposed EMS can reduce the fuel consumption of the vehicle by 6.69 and 6.35 l/100 km using the SC and the GP, respectively. In addition, the EMS based on NF trained by GP and NF trained by SC can reduce the fuel consumption of the vehicle by 11.8% and 7.08% compared with the case without the controller, respectively.

Partial discharge (PD) measurements have proved their reliability for health monitoring of insulation systems in power system components including synchronous generators, power transformers, switchgear and cables etc. Online condition monitoring and pro-active detection of PD faults have been highly demanded over the last two decades. This paper provides results from a research project to develop advanced non-intrusive sensing technologies that are cost effective, reliable and efficient for early detection of PD faults in medium voltage (MV) and high voltage (HV) air-insulated switchgear. Three sensors (high frequency E-field (D-dot) sensor, Rogowski coil and loop antenna) have been developed and tested under various PD faults and their performance were evaluated in comparison with high frequency current transformer (HFCT) which is being used commercially for PD testing and measurement. Among these three sensors, it is shown that D-dot sensor and Rogowski coil are more dependable when... [more]

Electronics (particularly power electronics) are the core element in many energy-related applications. Due to the increasing power density of electronic parts, the demands on thermal management solutions have risen considerably. As a novel passive and highly efficient cooling technology, pulsating heat pipes (PHPs) can transfer heat away from critical hotspots. In this work, we present two types of small and compact PHPs with footprints of 50 × 100 mm2, thicknesses of 2 and 2.5 mm and with high fluid channel density, optimized for cooling electronic parts with high power densities. The characterization of these PHPs was carried out with a strong relation to practical applications, revealing excellent thermal properties. The thermal resistance was found to be up to 90% lower than that of a comparable solid copper plate. Thus, a hot part with defined heating power would remain at a much lower temperature level and, for the same heater temperature, a much larger heating power could be app... [more]

Under the circumstances of rapid expansion of diverse forms of volatile and intermittent renewable energy sources, hydropower stations have become increasingly indispensable for improving the quality of energy conversion processes. As a consequence, Francis turbines, one of the most popular options, need to operate under off-design conditions, particularly for partial load operation. In this paper, a prototype Francis turbine was used to investigate the pressure fluctuations and hydraulic axial thrust pulsation under four partial load conditions. The analyses of pressure fluctuations in the vaneless space, runner, and draft tube are discussed in detail. The observed precession frequency of the vortex rope is 0.24 times that of the runner rotational frequency, which is able to travel upstream (from the draft tube to the vaneless space). Frequencies of both 24.0 and 15.0 times that of the runner rotational frequency are detected in the recording points of the runner surface, while the ma... [more]

Propane-Precooled Mixed Refrigerant (C3MR) and Single Mixed Refrigerant (SMR) processes are considered as optimal choices for onshore and offshore natural gas liquefaction, respectively. However, from thermodynamics point of view, these processes are still far away from their maximum achievable energy efficiency due to nonoptimal execution of the design variables. Therefore, Liquefied Natural Gas (LNG) production is considered as one of the energy-intensive cryogenic industries. In this context, this study examines a single-solution-based Vortex Search (VS) approach to find the optimal design variables corresponding to minimal energy consumption for LNG processes, i.e., C3MR and SMR. The LNG processes are simulated using Aspen Hysys and then linked with VS algorithm, which is coded in MATLAB. The results indicated that the SMR process is a potential process for offshore sites that can liquefy natural gas with 16.1% less energy consumption compared with the published base case. Whereas,... [more]

The interconnection of new generating and storing devices to the power grid imposes the necessity of synchronizing, so the power flow can be manipulated and distributed. In the presence of an increasingly perturbed electric grid, many proposals of novel and modified synchronization techniques attained enough robustness to deal with known perturbations. However, such proposals exhibit drawbacks on their own, leaving open enhancement opportunities, mostly over their discrete implementation—e.g., sampling issues and not-considered inter/harmonics—and their inherent complexity—e.g., the need for frequency adaptability. In this work, three traditional synchronous reference frame (SRF) phase-locked loops (PLL) are modified to implement discrete filtering, such as the well-known proposals based on moving average filters (MAFs), to avoid the problems mentioned above, known for affecting the MAF’s performance. This proposal makes use of discrete, efficient units modularly assembled to yield a s... [more]

Coal burst is a type of dynamic geological hazard in coal mine. In this study, a modified bursting energy index, which is defined as the ratio of elastic strain energy at the peak strength to the released strain energy density at the post-peak stage, was proposed to evaluate the coal burst proneness. The calculation method for this index was also introduced. Two coal mines (PJ and TJH coal mines) located in Ordos coalfield were used to verify the validity of the proposed method. The tests results indicate that modified bursting energy index increases linearly with increasing uniaxial compressive strength. The parameter A, which is used to fit relation between total input and elastic strain energy density, has a significant effect on the modified bursting energy index. A large value of parameter A means more elastic strain energy before the peak strength while a small value indicates most of input energy was dissipated. Finally, the coal burst proneness of these two coal mines was evalu... [more]

Water jet technology is a key technology in the marine natural gas hydrate (NGH) solid fluidization mining method. As an important parameter in water jet breaking NGH sediments technology, the critical breaking velocity of NGH sediments is unknown. In the present research, an orthogonal design experiment is carried out to study the critical velocity of NGH breakage by water jet, using frozen soil and sand as experimental samples. First, the time it takes to reach maximum NGH breaking depth is determined. Then, ultimate breaking distance is studied with respect to the NGH saturation, jet pressure, and nozzle diameter. Following that, the variation of critical velocity with NGH saturation is analyzed. Eventually, a formula to calculate the critical velocity for marine NGH breakage by water jet process is established, and the undetermined coefficient (η) in the formula is calibrated with the experiment data. The results show that the ultimate breaking distance is mostly achieved within 63... [more]

This paper introduces an underdetermined nonlinear programming model where the equality constraints are fewer than the design variables defined on a compact set for the solution of the optimal Phasor Measurement Unit (PMU) placement. The minimization model is efficiently solved by a recursive quadratic programming (RQP) method. The focus of this work is on applying an RQP to attempt to find guaranteed global minima. The proposed minimization model is conducted on IEEE systems. For all simulation runs, the RQP converges superlinearly towards optimality in a finite number of iterations without to be rejected the full step-length. The simulation results indicate that the RQP finds out the minimal number and the optimal locations of PMUs to make the power system wholly observable.

NiFe electrodes are developed for the oxygen evolution reaction (OER) in an alkaline electrolyser based on an anion exchange membrane (AEM) separator and fed with diluted KOH solution as supporting electrolyte. This study reports on the electrochemical behaviour of two different NiFe-oxide compositions (i.e., Ni1Fe1-oxide and Ni1Fe2-oxide) prepared by the oxalate method. These catalysts are assessed for single-cell operation in an MEA including a Sustainion™ anion-exchange membrane. The electrochemical polarization shows a current density of 650 mA cm−2 at 2 V and 50 °C for the Ni1Fe1 anode composition. A durability test of 500 h is carried out using potential cycling as an accelerated stress-test. This shows a decrease in current density of 150 mA cm−2 mainly during the first 400 h. The performance achieved for the anion-exchange membrane electrolyser single-cell based on the NiFeOx catalyst appears promising. However, further improvements are required to enhance the stability under t... [more]

Electric cycling is one of the major damage sources in lithium-ion batteries and extensive work has been produced to understand and to slow down this phenomenon. The damage is related to the insertion and extraction of lithium ions in the active material. These processes cause mechanical stresses which in turn generate crack propagation, material loss and pulverization of the active material. In this work, the principles of diffusion induced stress theory are applied to predict concentration and stress field in the active material particles. Coupled and uncoupled models are derived, depending on whether the effect of hydrostatic stress on concentration is considered or neglected. The analytical solution of the coupled model is proposed in this work, in addition to the analytical solution of the uncoupled model already described in the literature. The analytical solution is a faster and simpler way to deal with the problem which otherwise should be solved in a numerical way with finite... [more]