Assessing the influence of key parameters governing the formation of hydrates and determining the capacity of the latter to store gaseous molecules is needed to improve our understanding of the role of natural gas hydrates in the oceanic methane cycle. Such knowledge will also support the development of new industrial processes and technologies such as those related to thermal energy storage. In this study, high-pressure laboratory methane hydrate formation and dissociation experiments were carried out in a sandy matrix at a temperature around 276.65 K. Methane was continuously injected at constant flowrate to allow hydrate formation over the course of the injection step. The influence of water saturation, methane injection flowrate and particle size on hydrate formation kinetics and methane storage capacity were investigated. Six water saturations (10.8%, 21.6%, 33%, 43.9%, 55% and 66.3%), three gas flowrates (29, 58 and 78 mLn·min−1) and three classes of particle size (80−140, 315−45... [more]

A light detection and ranging (LIDAR) wind profiler was used to estimate the wind speed in the southern coast of Santa Catarina State, Brazil. This profiler was installed on a coastal platform 250 m from the beach, and recorded wind speed and direction from January 2017 to December 2018. The power generation from three wind turbines was simulated, to obtain estimations of the average power, energy generation and capacity factor, as well as to assess the performance of a hypothetical wind farm. The scale and shape parameters of the Weibull distribution were evaluated and compared with those of other localities in the state. The prevailing winds tend to blow predominantly from the northeast and southwest directions. Wind magnitudes are higher for the NE and SW ocean sectors where the average wind power density can reach 610−820 W m−2. The Vestas 3.0 turbine spent the largest percentage of time in operation (>76%). The higher incidence of strong northeasterly winds in 2017 and more freque... [more]

In regions where natural gas is used for both power generation and heating buildings, extreme cold weather events can place the electrical system under enormous stress and challenge the ability to meet residential heating and electric demands. Residential demand response has long been used in the power sector to curtail summer electric load, but these types of programs in general have not seen adoption in the natural gas sector during winter months. Natural gas demand response (NG-DR) has garnered interest given recent extreme cold weather events in the United States; however, the magnitude of savings and potential impacts—to occupants and energy markets—are not well understood. We present a case-study analysis of the technical potential for residential natural gas demand response in the northeast United States that utilizes diverse whole-building energy simulations and high-performance computing. Our results show that NG-DR applied to residential heating systems during extreme cold-we... [more]

Small-scale hybrid parabolic dish concentrated solar power systems are a promising option to obtain distributed electricity. During the day, solar energy is used to produce electricity, and the absence of sunlight can be overwhelmed with fuel combustion. This study presents a thermo-economic survey for a hybridized power plant in different regions of Spain, considering the local climatic conditions. The developed model considers the instant solar irradiance and ambient temperature dynamically, providing an estimation of the power output, the associated fuel consumption, and the most relevant pollutant emissions linked to combustion. Hybrid and combustion-only operating modes at selected geographical locations in Spain (with different latitudes, mean solar irradiances, and meteorological conditions) are analyzed. The levelized cost of electricity indicator is estimated as a function of investment, interest rate, maintenance, and fuel consumption actual costs in Spain. Values of about 12... [more]

Resilient operation of medium/large scale off-grid energy systems, which is a key challenge for energy crisis solutions, requires continuous and sustainable energy resources. Conventionally, micro energy grids (MEGs) are adopted to supply electricity and thermal energy simultaneously. Fossil-fired gensets, such as diesel generators, are indispensable components for off-grid MEGs due to the intermittent nature of renewable energy sources (RESs). However, fossil-fired gensets emit a significant amount of greenhouse gases (GHGs). Therefore, this study investigates an alternative source as an economical and environmental replacement for diesel gensets that can reduce GHG emissions and ensure system reliability. A MEG is developed in this paper to support a considerably large-scale electric and thermal demand at Ontario Tech University (UOIT). Different sizes of diesel gensets and RESs, such as solar, wind, hydro, and biomass, are combined in the MEG for off-grid applications. To evaluate d... [more]

Microgrids are small scale electrical power systems that comprise distributed energy resources (DER), loads, and storage devices. The integration of DER into the electrical power system basically allows the clustering of small parts of the main grid into Microgrids. Due to the increasing amount of renewable energy, which is integrated into the main grid, high power fluctuations are expected to become common in the next years. This carries the risk of blackouts to be also more likely in the future. Microgrids hold the potential of increasing reliability of supply, since they are capable of providing a backup supply during a blackout of the main grid. This paper investigates the black-starting and islanding capabilities of a battery energy storage system (BESS) in order to provide a possible backup supply for a small part of the main grid. Based on field tests in a real Microgrid, the backup supply of a residential medium voltage grid is tested. Whereas local wind turbines within this gr... [more]

Anomaly detection for wind turbine condition monitoring is an active area of research within the wind energy operations and maintenance (O & M) community. In this paper three models were compared for multi-megawatt operational wind turbine SCADA data. The models used for comparison were One-Class Support Vector Machine (OCSVM), Isolation Forest (IF), and Elliptical Envelope (EE). Each of these were compared for the same fault, and tested under various different data configurations. IF and EE have not previously been used for fault detection for wind turbines, and OCSVM has not been used for SCADA data. This paper presents a novel method of condition monitoring that only requires two months of data per turbine. These months were separated by a year, the first being healthy and the second unhealthy. The number of anomalies is compared, with a greater number in the unhealthy month being considered correct. It was found that for accuracy IF and OCSVM had similar performances in both traini... [more]

The mechanical power and wake flow field of a 1:40 scale model of the US Department of Energy’s Reference Model 1 (RM1) dual rotor tidal energy converter are characterized in an open-channel flume to evaluate power performance and wake flow recovery. The NACA-63(4)-24 hydrofoil profile in the original RM1 design is replaced with a NACA-4415 profile to minimize the Reynolds dependency of lift and drag characteristics at the test chord Reynolds number. Precise blade angular position and torque measurements were synchronized with three acoustic Doppler velocimeters (ADV) aligned with each rotor centerline and the midpoint between the rotor axes. Flow conditions for each case were controlled to maintain a hub height velocity, uhub= 1.04 ms−1, a flow Reynolds number, ReD= 4.4 × 105, and a blade chord length Reynolds number, Rec= 3.1 × 105. Performance was measured for a range of tip-speed ratios by varying rotor angular velocity. Peak power coefficients, CP= 0.48 (right rotor) and CP= 0.43... [more]

Potential-induced degradation (PID) of photovoltaic (PV) cells is one of the most severe types of degradation, where the output power losses in solar cells may even exceed 30%. In this article, we present the development of a suitable anti-reflection coating (ARC) structure of solar cells to mitigate the PID effect using a SiO2 ARC layer. Our PID testing experiments show that the proposed ARC layer can improve the durability and reliability of the solar cell, where the maximum drop in efficiency was equal to 0.69% after 96 h of PID testing using an applied voltage of 1000 V and temperature setting at 85 °C. In addition, we observed that the maximum losses in the current density are equal to 0.8 mA/cm2, compared with 4.5 mA/cm2 current density loss without using the SiO2 ARC layer.

Despite strong political efforts in Europe, industrial small- and medium-sized enterprises (SMEs) seem to neglect adopting practices for energy efficiency. By taking a cultural perspective, this study investigated what drives the establishment of energy efficiency and corresponding practices in SMEs. Based on 10 ethnographic case studies and a quantitative survey among 500 manufacturing SMEs, the results indicate the importance of everyday employee behavior in achieving energy savings. The studied enterprises value behavior-related measures as similarly important as technical measures. Raising awareness for energy issues within the organization, therefore, constitutes an essential leadership task that is oftentimes perceived as challenging and frustrating. It was concluded that the embedding of energy efficiency in corporate strategy, the use of a broad spectrum of different practices, and the empowerment and involvement of employees serve as major drivers in establishing energy effici... [more]

High transportation costs make energy and food expensive in remote communities worldwide, especially in high-latitude Arctic climates. Past attempts to grow food indoors in these remote areas have proven uneconomical due to the need for expensive imported diesel for heating and electricity. This study aims to determine whether solar photovoltaic (PV) electricity can be used affordably to power container farms integrated with a remote Arctic community microgrid. A mixed-integer linear optimization model (FEWMORE: Food−Energy−Water Microgrid Optimization with Renewable Energy) has been developed to minimize the capital and maintenance costs of installing solar photovoltaics (PV) plus electricity storage and the operational costs of purchasing electricity from the community microgrid to power a container farm. FEWMORE expands upon previous models by simulating demand-side management of container farm loads. Its results are compared with those of another model (HOMER) for a test case. FEWM... [more]

The construction of metro line energy management center (MLEMC) is one of the important parts of metro line, which is the key organization to realize the energy consumption management of the metro operation. To protect the safety of adjacent high-rise buildings during the blasting of subway foundation pit engineering, it is crucial to study the response characteristics of building structures. This paper takes the MLEMC vertical pit blasting project of Wuhan Metro Line 8 as an example. The law of blasting vibration attenuation along the earth’s surface and the vibration velocity response characteristics of the building structure were analyzed by small explosive test. LSDYNA numerical model was established, and the reliability of the model and parameters was verified by experimental data. Combined with the relevant specifications, the maximum charge in single delay was calculated and analyzed. The numerical model of the maximum charge in single was established, and the prediction model o... [more]

Downwind turbines have favorable characteristics such as effective energy capture in up-flow wind conditions over complex terrains. They also have reduced risk of severe accidents in the event of disruptions to electrical networks during strong storms due to the free-yaw effect of downwind turbines. These favorable characteristics have been confirmed by wind-towing tank experiments and computational fluid dynamics (CFD) simulations. However, these advantages have not been fully demonstrated in field experiments on actual wind farms. In this study—although the final objective was to demonstrate the potential advantages of downwind turbines through field experiments—field measurements were performed using a vertical-profiling light detection and ranging (LiDAR) system on a wind farm with downwind turbines installed in complex terrains. To deduce the horizontal wind speed, vertical-profiling LiDARs assume that the flow of air is uniform in space and time. However, in complex terrains and/... [more]

Extensive application of small and medium-sized unmanned aerial vehicles (UAVs) have already made the development of corresponding power system a research hotspot nowadays. Two-stroke heavy fuel light aeroengine (2SHFLA) is selected as the research focus in this paper. The working principle of 2SHFLA with different fuel injection systems is elaborated systematically. By dividing the initial prototype engine into several subsystems, the simulation platform is set up with its key model parameters accurately calibrated against the test data. Simulation platforms of the other two types of engines are subsequently constructed based on the pre-calibrated simulation platform of the initial prototype engine. Afterwards, comparative simulation is performed and the corresponding simulation results include: (1) comparison of performance characteristics of the initial prototype engine fueled with regular gasoline/heavy fuel; (2) comprehensive comparison of the performance characteristics of all th... [more]

Sand ingestion is highly detrimental for gas turbines because it leads to erosion and corrosion of engine components, accelerating material fatigue and contributing to global engine failure. In this paper the high velocity impact of a molten sand particle onto a solid wall is investigated by means of the Smoothed Particles Hydrodynamics method where the three phases are taken into account. Nominal conditions are a 25 μm particle composed of molten sand (dynamic viscosity μl=11 Pa·s) impacting the wall at a velocity of 250 m/s. The influence of different parameters are explored such as the mechanical properties of the molten sand particle (density, viscosity, surface tension), the impact conditions (velocity magnitude, particle size and angle of impact) as well as the particle shape (sphere or cube with different geometrical features impacting the wall). It is found that the particles do not form a lamella during the impact but mostly conserve its initial shape. It is also confirmed tha... [more]

We analyzed the role of predictable and unpredictable variability in the identification of optimal renewable energy mixes in an electricity system. Renewable energy sources are the fastest growing energy generation technology, but the variable nature of production linked to climate variability raises structural, technological and economical issues. This work proposes the differentiation of the treatment applied to predictable and unpredictable variability in the context of Markowitz portfolio theory for optimal renewable deployment. The e4clim model was used as a tool to analyze the impact of predictable sources of generation variability on the optimal renewable energy mixes. Significant differences appeared, depending on the consideration of risk, all of them showing room for improvement with respect to the current situation. The application of the methods developed in this study is encouraged in mean-variance analyses, since its contribution favors scenarios where unpredictable varia... [more]

The increasing resort to renewable energy distributed generation, which is needed to mitigate anthropogenic CO2 emissions, leads to challenges concerning the proper operation of electric distribution systems. As a result of the intrinsic nature of Renewable Energy Sources (RESs), this generation shows a high volatility and a low predictability that make the balancing of energy production and consumption difficult. At the same time, the electrification of new energy-intensive sectors (such as heating) is expected. This complex scenario paves the way for new sources of flexibility that will have more and more relevance in the coming years. This paper analyses how the electrification of the heating system, combined with an electric flexibility utilisation module, can be used to mitigate the problems related to the fluctuating production of RES. By using Power-to-Heat (P2H) technologies, buildings are able to store the overproduction of RES in the form of thermal energy for end-use accordi... [more]

It has been reported that improving electrical conductivity and maintaining stable structure during discharge/charge process are challenge for Si to be used as an anode for lithium ion batteries (LIB). To address this problem, milkweed (MW) was carbonized to prepare hollow carbon microtubes (HCMT) derived from biomass as an anode template for LIB. In order to improve electrical conductivity, various materials such as chitosan (CTS), agarose, and polyvinylidene fluoride (PVDF) are used as carbon source (C1, C2, and C3) by carbonization. Carbon coated HCMT@Si composits, HCMT@Si@C1, HCMT@Si@C1@C2, and HCMT@Si@C1@C3, have been successfully synthesized. Changes in structure and crystallinity of HCMT@Si composites were characterized by using X-ray diffraction (XRD). Specific surface area for samples was calculated by using BET (Brunauer−Emmett−Teller). Also, pore size and particle size were obtained by particle and pore size analysis system. The surface morphology was evaluated using high re... [more]

Photovoltaic (PV) installations located in the northern hemisphere must be oriented to the south in order to obtain maximal annual yield. This is mainly driven by the remuneration mechanisms which incentivize maximal energy production to a certain extent. Nowadays, such support mechanisms are declining or even phased out in many countries. Hence, self-consuming the produced energy is getting more viable. In order to match better the load demand pattern, the azimuth angle of a PV installation could be changed or oriented towards multiple directions. This article investigates the benefits of PV installations facing other directions than the south. Therefore, the Hay & Davies transposition model has been used to calculate the in-plane irradiance, as it is found in the literature to be the most accurate for non-south faced PV installations. In order to determine the benefit, a large dataset of real measured consumption profiles has been used and then divided according to their annual consu... [more]

Lithium-ion batteries (LiBs) are a proven technology for energy storage systems, mobile electronics, power tools, aerospace, automotive and maritime applications. LiBs have attracted interest from academia and industry due to their high power and energy densities compared to other battery technologies. Despite the extensive usage of LiBs, there is a substantial fire risk associated with their use which is a concern, especially when utilised in electric vehicles, aeroplanes, and submarines. This review presents LiB hazards, techniques for mitigating risks, the suppression of LiB fires and identification of shortcomings for future improvement. Water is identified as an efficient cooling and suppressing agent and water mist is considered the most promising technique to extinguish LiB fires. In the initial stages, the present review covers some relevant information regarding the material constitution and configuration of the cell assemblies, and phenomenological evolution of the thermal ru... [more]

Molten gasification is considered as a promising technology for the processing and safe disposal of hazardous wastes. During this process, the organic components are completely converted while the hazardous materials are safely embedded in slag via the fusion-solidification-vitrification transformation. Ideally, the slag should be glassy with low viscosity to ensure the effective immobilization and steady discharge of hazardous materials. However, it is very difficult to predict the characteristics of slag using existing empirical equations or conventional mathematical methods, due to the complex non-linear relationship among the phase transformation, vitrification transition and chemical composition of slag. Equipped with a strong nonlinear mapping ability, an artificial neural network may be able to predict the properties of slags if a large amount of data is available for training. In this work, over 10,000 experimental data points were used to train and develop a slag classificatio... [more]

The shell-and-tube type gas-to-gas membrane humidifier used with air supply to polymer electrolyte membrane fuel cell supplies heat and vapor through a membrane and does not require an additional power source. Packing porous metal foam in the flow path of the membrane humidifier can result in higher heat and mass transfer efficiencies due to heat conduction through metal. In this study, the influence of various operating conditions and types of porous metal foams on the transport characteristics of the membrane humidifier are evaluated by simulation. The main factor causing the improvement of heat and mass transfer is the high conductivity of the porous metal foam, which is significantly correlated with the type of material used, compression ratio, and pore diameter. Additionally, the heat and mass transfer changes significantly when the flow velocity and channel size change due to the effect of the metal foam becoming more pronounced.

The stationary photovoltaic array can be used to charge the different vehicle batteries and, in parallel, be used as a power source for the utility grid or standalone devices placed such as in campers. The main objective of the study was to compare chosen electrical characteristics of two assemblies with each containing the same PV array, boost converter and inverter, and a different battery, such as the Li-S one and the Li-ion one, respectively. Differences occurring during modelling of Li-ion and Li-S batteries were discussed. The model of the chosen photovoltaic array was used during analysis. The models based on electrical equivalent circuits for Li-ion battery and of Li-S battery were utilized during calculations. The models of the boost converter and boost inverter of known topology parameters were utilized during simulations. In the chosen performances (courses of voltages and currents versus time) obtained from the simulation of the sets composed of the Li-S battery cooperating... [more]

Offshore wind energy is a rapidly maturing renewable energy technology that is poised to play an important role in future energy systems. The respective advances refer among others to the monopile foundation that is frequently used to support wind turbines in the marine environment. In the present research paper, the structural response of tall wind energy converters with various stiffening schemes is studied during the erection phase as the latter are manufactured in modules that are assembled in situ. Rings, vertical stiffeners, T-shaped stiffeners and orthogonal stiffeners are considered efficient stiffening schemes to strengthen the tower structures. The loading bearing capacity of offshore monopile wind turbine towers with the four types of stiffeners were modeled numerically by means of finite elements. Applying a nonlinear buckling analysis, the ultimate bearing capacity of wind turbine towers with four standard stiffening schemes were compared in order to obtain the optimum sti... [more]

Photovoltaic monitoring data are the primary source for studying photovoltaic plant behavior. In particular, performance loss and remaining-useful-lifetime calculations rely on trustful input data. Furthermore, a regular stream of high quality is the basis for pro-active operation and management activities which ensure a smooth operation of PV plants. The raw data under investigation are electrical measurements and usually meteorological data such as in-plane irradiance and temperature. Usually, performance analyses follow a strict pattern of checking input data quality followed by the application of appropriate filter, choosing a key performance indicator and the application of certain methodologies to receive a final result. In this context, this paper focuses on four main objectives. We present common photovoltaics monitoring data quality issues, provide visual guidelines on how to detect and evaluate these, provide new data imputation approaches, and discuss common filtering approa... [more]