At the beginning of the 20th century the operational issues of the Otto engine had not been fully resolved. The work presented here seeks to chronicle the development of one of the alternative design pathways, namely the replacement for the gas exchange mechanism of the more conventional poppet valve arrangement with that of a sleeve valve. There have been several successful engines built with these devices, which have a number of attractive features superior to poppet valves. This review moves from the initial work of Charles Knight, Peter Burt, and James McCollum, in the first decade of the 20th century, through the work of others to develop a two-stroke version of the sleeve-valve engine, which climaxed in the construction of one of the most powerful piston aeroengines ever built, the Rolls-Royce Crecy. After that period of high activity in the 1940s, there have been limited further developments. The patent efforts changed over time from design of two-stroke sleeve-drive mechanisms... [more]

In this study, experiments were performed to use the waste heat in a billet casting industry utilizing bismuth telluride thermoelectric generators (TEGs). Four d-type absorber plates made of copper were installed above the manufactured billet during the cooling process. Three sides of each absorber plate were attached to thermoelectric units. Therefore, a total of 12 units of the thermoelectric system were found to generate a power of 339 W. The power density of the TEG system was found to be 981 W/m2 while running the system at the operating voltage of the battery energy storage system (58 V). A one-dimensional numerical simulation was carried out using FloMASTERTM v9.1 (Mentor Graphics Corporation, Siemens, Dallas, TX, USA) to verify the experimental results, and the numerical results were found to exhibit good agreement with the experimental results. Furthermore, a one-dimensional numerical simulation was carried out to obtain the heat transfer characteristics at varying flow rates... [more]

The power quality of grid-connected inverters (GCIs) is attracting a lot of attention as the number of distributed generation systems with renewable energy sources are increased. It is well known that the harmonics present in the grid have a lot of detrimental effects on the equipment and devices connected to a power system network such as heating and derating. These effects lead to problems in terms of safety and lifespan. Therefore, harmonic standards such as IEEE 519 and P1547 suggest that GCIs should achieve total harmonic distortion (THD) of the output current that is less than 5%. However, it is not easy to achieve the current THD of GCIs that is less than 5% with only an output filter under distorted grid conditions. In this paper, a harmonic compensation method using a lock-in amplifier (LIA) is proposed. Due to the outstanding performance of the LIA, accurate information of the harmonics can be obtained. This information is used to eliminate the harmonics by the simple PI cont... [more]

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This invest... [more]

An increasing percentage of ethanol in fuel leads to significant changes in polarity and solubility, which makes conventional gasoline deposit control additives (DCAs) difficult to dissolve in ethanol fuels, resulting in the formation of deposits on engine elements. Critical areas of deposit formation in an engine are constituted by inlet valves, combustion chambers, and fuel injectors. As a consequence, operational parameters of the engine are disturbed to a large extent by the total effect of the deposits. To prevent the aforementioned phenomena, in the operation of engines fueled with ethanol-containing blends, it is necessary to use specifically prepared DCAs. The paper briefly presents a process of development of DCAs dedicated to high-ethanol fuels. Each of the prepared DCA formulations contained a substance having detergent-emulsifying properties (referred to in the text as DEM), a carrier oil, and a solvent. The composition and ratios of components used in the DCA, by testing t... [more]

Heat pipe heat exchangers (HPHEXs) are widely used in various industries. In this paper, a novel model of a liquid−liquid heat pipe heat exchanger in a countercurrent manner is established by considering the evaporation and condensation thermal resistances inside the heat pipes (HPs). The discrete method is added to the HPHEX model to determine the thermal resistances of the HPs and the temperature change trend of the heat transfer fluid in the HPHEX. The established model is verified by the HPHEX structure and experimental data in the existing literature and demonstrates numerical results that agree with the experimental data to within a 5% error. With the current model, the investigation compares the effectiveness and minimum vapor temperature of the HPHEX with three types of HP diameters, different mass flow rates, and different H* values. For HPs with a diameter of 36 mm, the effectiveness of each is improved by about 0.018 to 0.029 compared to HPs with a diameter of 28 mm. The res... [more]

With the advent of restructuring in the power industry, the conventional unit commitment problem in power systems, involving the minimization of operation costs in a traditional vertically integrated system structure, has been transformed to the profit-based unit commitment (PBUC) approach, whereby generation companies (GENCOs) perform scheduling of the available production units with the aim of profit maximization. Generally, a GENCO solves the PBUC problem for participation in the day-ahead market (DAM) through determining the commitment and scheduling of fossil-fuel-based units to maximize their own profit according to a set of forecasted price and load data. This study presents a methodology to achieve optimal offering curves for a price-taker GENCO owning compressed air energy storage (CAES) and concentrating solar power (CSP) units, in addition to conventional thermal power plants. Various technical and physical constraints regarding the generation units are considered in the pro... [more]

To improve indirect drying efficiency, the effect of soda residue on the drying characteristics of coking coal were studied using a self-made indirect drying system. A tube furnace was used in the dry distillation of coal samples with soda residue, and the coke properties were analyzed. The results indicated that the soda residue has a significant influence on the increase in the heating rate of coal samples in the temperature distribution range of 90 to 110 °C. With the addition of 2%, 5%, and 10% soda residue, the drying rates increased by 11.5%, 25.3%, and 37.3%, respectively at 110 °C. The results of dry distillation show that addition of 2%, 5% and 10% soda residue decreases the carbon loss quantity by 4.67, 4.99, and 8.82 g, respectively. The mechanical strength of coke samples satisfies the industrial conditions when the soda residue ratio ranges from 2% to 5%. Soda residue can improve the active point of coke dissolution reaction and inhibit coke internal solution. Economically... [more]

To make biofuel production feasible from an economic point of view, several studies have investigated the main associated bottlenecks of the whole production process through approaches such as the “cradle to grave” approach or the Life Cycle Assessment (LCA) analysis, being the main constrains the feedstock collection and transport. Whilst several feedstocks are interesting because of their high sugar content, very few of them are available all year around and moreover do not require high transportation’ costs. This work aims to investigate if the “zero miles” concept could bring advantages to biofuel production by decreasing all the associated transport costs on a locally established production platform. In particular, a specific case study applied to the Technical University of Denmark (DTU) campus is used as example to investigate the advantages and feasibility of using the spent coffee grounds generated at the main cafeteria for the production of bioethanol on site, which can be su... [more]

Lowering energy consumption is one of the most important challenges of the modern world. Since the construction sector accounts for 40% of total energy consumption worldwide, the Parliament of the European Union has developed a Directive, according to which all newly designed and thermally upgraded buildings should meet the requirements of almost zero energy demand (nZEBs) from 1 January 2021. At the same time, in Poland, but also in many other countries in the world, there is a growing oversupply of office space in large cities with a simultaneous increase in demand for apartments, which is caused, among other things, by the increase in the share of remote work and the COVID-19 pandemic. Consequently, this is forcing owners to change the use of buildings from office to residential. This article analyses the possibilities of changing the function of an office building to a multi-family residential building. For both functional solutions, a comparative energy analysis was carried out, t... [more]

The following article analyzes the effectiveness of directional hydraulic fracturing (DHF) as a method of rock burst prevention, used in black coal mining with a longwall system. In order to define changes in seismic activity due to DHF at the “Rydułtowy” Black Coal Mine (Upper Silesia, Poland), observations were made regarding the seismic activity of the rock mass during coal mining with a longwall system using roof layers collapse. The seismic activity was recorded in the area of the longwall itself, where, on a part of the runway, the rock mass was expanded before the face of the wall by interrupting the continuity of the rock layers using DHF. The following article presents measurements in the form of the number and the shock energy in the area of the observed longwall, which took place before and after the use of DHF. The second part of the article unveils the results of numerical modeling using the discrete element method, allowing to track the formation of goafs for the variant... [more]

This paper analyzes the intelligent use of time-varying electrical load via developing efficient energy utilization patterns using demand-side management (DSM) strategies. This approach helps distribution utilities decrease maximum demand and electrical energy billing costs. A case study of DSM implementation of electric energy utility for an educational building Alagappa Chettiar Government College of Engineering and Technology (ACGCET) campus was simulated. The new optimum energy load model was established for peak and off-peak periods from the system’s existing load profile using peak clipping and load shifting DSM techniques. The result reflects a significant reduction in maximum demand from 189 kW to 170 kW and a reduction in annual electricity billing cost from $11,340 to $10,200 (approximately 10%) in the upgraded system. This work highlights the importance of time of day (TOD) tariff structure consumers that aid reduction in their distribution system’s maximum demand and demand... [more]

The results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations that jointly describe the dependence of the average Nusselt number on Rayleigh number and confinement ratios were examined. As a heat source served electrically heated horizontal tube immersed in an ambient fluid. Experiments were performed with pure ethylene glycol (EG), distilled water (W), and a mixture of EG and water at 50%/50% by volume. A set of empirical correlation equations for the prediction of Nu numbers for Rayleigh number range 3.6 × 104 < Ra < 9.2 × 105 or 3.6 × 105 < Raq < 14.8 × 106 and Pr number range 4.5 ≤ Pr ≤ 160 has been... [more]

With an increase in renewable energy generation in the United States, there is a growing need for more frequency regulation to ensure the stability of the electric grid. Fast ramping natural gas plants are often used for frequency regulation, but this creates emissions associated with the burning of fossil fuels. Energy storage systems (ESSs), such as batteries and flywheels, provide an alternative frequency regulation service. However, the efficiency losses of charging and discharging a storage system cause additional electrical generation requirements and associated emissions. There is not a good understanding of these indirect emissions from charging and discharging ESSs in the literature, with most sources stating that ESSs for frequency regulation have lower emissions, without quantification of these emissions. We created a model to estimate three types of emissions (CO2, NOX, and SO2) from ESSs providing frequency regulation, and compare them to emissions from a natural gas plant... [more]

Natural gas hydrate (NGH) has been widely focused on having great potential for alternative energy. Numerous studies on gas production from hydrate-bearing sediments have been conducted in both laboratory and field. Since the strength of hydrate-bearing sediments depends on the saturation of NGH, the decomposition of NGH may cause the failure of sediments, then leading to reservoir deformation and other geological hazards. Plenty of research has shown that the reservoir deformation caused by hydrate decomposition is considerable. In order to investigate this, the influence of sediment deformation on the production of NGH, a fully coupled thermo-hydro-chemo-mechanical (THMC) model is established in this study. The interaction effects between reservoir deformation and hydrate dissociation are discussed by comparing the simulation results of the mechanical coupling and uncoupled models on the laboratory scale. Results show that obvious differences in behaviors between gas and water produc... [more]

Flexible, system-oriented operating strategies are becoming increasingly important in terms of achieving a climate-neutral energy system transformation. Solid-oxide electrolysis (SOEC) can play an important role in the production of green synthesis gas from renewable energy in the future. Therefore, it is important to investigate the extent to which SOEC can be used flexibly and which feedback effects and constraints must be taken into account. In this study, we derived a specific load profile from an energy turnaround scenario that supports the energy system. SOEC short-stacks were operated and we investigated the impact that the load profile has on electrical stack performance and stack degradation as well as the product gas composition by means of Fourier-transform infrared spectroscopy. The stacks could follow the grid-related requirement profiles of secondary control power and minute reserves very well with transition times of less than two minutes per 25% of relative power. Only... [more]

Frequency support capability is becoming an important requirement for wind turbines, as wind power is increasingly integrated into power systems. In this paper, a frequency controller is implemented and validated. Such a controller allows wind turbines to help regulate the system frequency automatically and includes virtual inertia to help limit the rate of change of frequency. Compared with other methods, the controller achieves satisfactory frequency support capability with considerable simplicity. The controller is added to the grid-side converter controls, together with cascaded inner loops, which enables wind turbines to operate in grid-forming mode with overcurrent protection. The influence of the controller parameters on the frequency response is investigated.

This paper communicates on an innovative, laboratory size alkaline water electrolyser (AWE) system, capable of efficiently producing ultra-pure hydrogen and oxygen gases. The system is composed of a zero-gap, bipolar-electrode stack, equipped with a polymer-based membrane, along with two drying columns for effective purification of H2 and O2 gaseous products. An optimal electrochemical efficiency of the electrolyser stack is provided through the employment of catalytically activated, extended surface-area nickel foam electrodes. Laboratory electrochemical examinations of the electrolyser included a series of galvanostatic AWE and alternating current (a.c.) impedance (single cell) experiments. Complementary examinations covered catalyst’s surface topography analysis by combined SEM (Scanning Electron Microscopy) and EDX (Energy Dispersive X-ray Spectroscopy) techniques along with chromatographic evaluation of the purity of hydrogen and oxygen products.

S-shaped characteristics in turbine mode are prone to instabilities in associated transient processes. A single value of the speed factor corresponds to multiple values of the discharge factor, having the possibility of changing the operating point among the turbine, turbine brake, and reverse pump modes. Because of this characteristic, the S-shaped curves induce instability in transient processes. Understanding the hydraulic behavior of a turbine on the four-quadrant characteristic is important since it provides detailed performance information through the whole discharge range of the turbine. This study was numerically and experimentally investigated the scale effect on the S-shaped characteristics in the turbine transition region. The four-quadrant characteristic curves (full- and laboratory-scale) in the turbine mode were predicted by numerical simulations. To verify the predicted results, a laboratory-scale experiment was performed in the turbine, turbine brake, and reverse pump m... [more]

One of the requirements for ships equipped with dynamic positioning system is the ability to maintain a given position in various hydrometeorological conditions. At the same time, efforts at reducing electricity consumption are made in order to reduce operating costs and emissions of exhaust gases, such as sulfur oxides and greenhouse gases such as carbon dioxide (CO2). For this purpose, the ship designer at the design stage must predict both how much energy the ship will theoretically use during operation and how the expenditure can be reduced. The publication presents a comparison of energy consumption with two different approaches to ship positioning: the use of classic dynamic positioning utilizing a set of thrusters and by using a set of anchors. In order to determine the energy consumption during positioning, the matrix method was used, on the basis of which the analysis of the ability to hold the position of the ship (capability plot) was performed, in accordance with the recomm... [more]

The purpose of this study is to examine the relationship between renewable energy sources and economic growth of the South Asian Association for regional cooperation (SAARC) countries. This study uses three main renewable energy sources, namely geothermal, hydro, and wind.This study collects data set from SAARC countries from 1995 to 2018 and applies a fixed effect test and panel vector error correction model (PVECM) for data analysis. The overall results show that all three renewable energy sources have a positive significant impact on economic development among SAARC countries’ economies. Moreover, hydropower renewable energy has more effects and influences on economic growth as compared to the other two individual sources of renewable energy.

With the increasing penetration level of wind turbine generators (WTGs) integrated into the power system, the WTGs are enforced to aid network and fulfill the low voltage ride through (LVRT) requirements during faults. To enhance LVRT capability of permanent magnet synchronous generator (PMSG)-based WTG connected to the grid, this paper presents a novel coordinated control scheme named overspeed-while-storing control for PMSG-based WTG. The proposed control scheme purely regulates the rotor speed to reduce the input power of the machine-side converter (MSC) during slight voltage sags. Contrarily, when the severe voltage sag occurs, the coordinated control scheme sets the rotor speed at the upper-limit to decrease the input power of the MSC at the greatest extent, while the surplus power is absorbed by the supercapacitor energy storage (SCES) so as to reduce its maximum capacity. Moreover, the specific capacity configuration scheme of SCES is detailed in this paper. The effectiveness of... [more]

To extract viscous bitumen from oil sands reservoirs, steam is injected into the formation to lower the bitumen’s viscosity enabling sufficient mobility for its production to the surface. Steam-assisted gravity drainage (SAGD) is the preferred process for Athabasca oil sands reservoirs but its performance suffers in heterogeneous reservoirs leading to an elevated steam-to-oil ratio (SOR) above that which would be observed in a clean oil sands reservoir. This implies that the SOR could be used as a signature to understand the nature of heterogeneities or other features in reservoirs. In the research reported here, the use of the SOR as a signal to provide information on the heterogeneity of the reservoir is explored. The analysis conducted on prototypical reservoirs reveals that the instantaneous SOR (iSOR) can be used to identify reservoir features. The results show that the iSOR profile exhibits specific signatures that can be used to identify when the steam chamber reaches the top of... [more]

Recently, in two publications, Loewen expressed skepticism on the validity of the levelized cost of energy (LCOE) indicator, used to compare the economics of energy technologies [...]

The increase of the maximal cycle temperature is considered as one of the best tools to increase cycle efficiency for all thermodynamic cycles, including Organic Rankine Cycles (ORC). Technically, this can be done in various ways, but probably the best solution is the use of hybrid systems, i.e., using an added high-temperature heat source to the existing low-temperature heat source. Obviously, this kind of improvement has technical difficulties and added costs; therefore, the increase of efficiency by increasing the maximal temperature sometimes has technical and/or financial limits. In this paper, we would like to show that for an ideal, simple-layout ORC system, a thermodynamic efficiency-maximum can also exist. It means that for several working fluids, the thermodynamic efficiency vs. maximal cycle temperature function has a maximum, located in the sub-critical temperature range. A proof will be given by comparing ORC efficiencies with TFC (Trilateral Flash Cycle) efficiencies; for... [more]