In 2019, a coffee chain in Taiwan was found to be mixing relatively cheap Robusta beans into products marketed as 100% Arabica. Many studies show 16-OMC is a remarkable marker to distinguish Robusta from Arabica beans, and nuclear magnetic resonance (NMR) is a convenient and efficient technique for 16-OMC quantification. Here, a 500 MHz NMR was employed to determine the content of 16-OMC in coffee for adulterate evaluation. A total of 118 samples were analyzed including products from the coffee chain, raw materials (single coffee beans), and other commercial products. The contents of 16-OMC in single Robusta beans were between 1005.55 and 3208.32 mg/kg and were absent from single Arabica beans. The surveillance results indicate that 17 out of 47 blend products claiming to contain 100% Arabica had 16-OMC quantifications in the range of 155.74−784.60 mg/kg. Furthermore, all 17 products were produced by the same coffee chain. We confirmed that coffee chain adulterated Arabica with Robusta... [more]

In this study, we prepared chitosan/Fe(III)/deferoxamine nanoparticles with unimodal size distribution (hydrodynamic diameter ca. 250 nm, zeta potential ca. 32 mV). The elaborated nanoparticles are characterized by outstanding in vitro and in vivo antibacterial activity, which exceeds even that of commercial antibiotics ampicillin and gentamicin. Moreover, the nanoparticles are non-toxic. We found that the introduction of iron ions into the chitosan matrix increases the ability of the resulting nanoparticles to disrupt the integrity of the membranes of microorganisms in comparison with pure chitosan. The introduction of deferoxamine into the obtained nanoparticles sharply expands their effect of destruction the bacterial membrane. The obtained antibacterial nanoparticles are promising for further preclinical studies.

The concentralized distribution logistics in cruise-building imported materials (CDL-CIMs) constitute a complex process that requires a high degree of coordination between the multi-link and multi-participator. Delayed delivery, materials damaged, and cost overruns occur because of increasing uncertainties and risks, which may cause disjointedness in cruise construction planning. Therefore, it is essential to conduct a risk assessment of the CDL-CIMs to examine their adverse impacts on cruise construction. Drawing on the advantages of the failure modes and effects analysis (FMEA) method in risk assessment, an effective and efficient model is developed using a novel hybrid method in this paper, namely the rule-based Bayesian network (RBN) and utility function. The approach has its superiorities in dealing with vague and uncertainty risk information. In addition, the risk parameters from multiple perspectives concerning “occurrence likelihood”, “detection”, “delayed schedule”, “damaged q... [more]

To improve the wear resistance of the TMR blade and investigate the effect of nano-La2O3 and Mo on the wear resistance of laser cladding coating. 65Mn blade as the substrate, La2O3, Mo and Mo-La2O3 composite powders were added into Ni60a/SiC composite powder. Using scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and the CFT-I surface synthesizer, the phase composition, element distribution and friction and wear properties of the coating were analyzed to obtain the best composition of the composite coating. The results showed that the wear resistance of Mo-La2O3-Ni60a/SiC composite coating was the best. The coating was analyzed by X-ray diffraction and X-ray photoelectron spectroscopy. The coating contained hard phases such as CrB, CrC and Cr7C3, and the element distribution was uniform. It can be seen from the scanning electron microscope that the addition of nano-Mo and La2O3 improves the toughness and compactness of Ni60a/SiC composite coating, and t... [more]

Tailings, with their low utilisation rate and value, pose an urgent problem that needs to be solved. This study focused on foam ceramics and glass granules, which were prepared using gold tailings as the main raw materials, and the prepared microcrystalline foam ceramics were investigated. The optimum sample (S6) of foam ceramics consists of 77 wt% of gold tailings, 6 wt% of talc, 9 wt% of bentonite, 2 wt% of calcite, 0.9 wt% of foaming agent and 0.6% of water reducer. The optimum foaming temperature is 1190 °C, and the holding time is 60 min. The compressive strength and bulk density of the samples are 7.4 MPa and 396.4 kg/m3; nucleation temperature, crystallisation temperature, and crystallisation activation energy of glass particles are 700 °C ± 50 °C, 1100 °C ± 50 °C, and 1572 kJ/mol, respectively. Microanalysis results showed that the crystal phases of foam ceramics were mainly quartz, calcium silicate, and aluminium silicate, and crystallinity increases with increasing gold taili... [more]

Microbial fuel cells (MFCs) are a promising technology that can be applied in a bifunctional process in which wastewater treatment is used for renewable electric power generation. In this study, novel transition metal-modified Keggin-type lacunar polyoxometalate salts (L-POMs) Cs5PMo11M(H2O)O39 (M = Fe, Co), were synthesized and characterized by X-ray diffraction, SEM, EDX, IR, TGA/DSC, and UV-Vis/DSR spectroscopies to be tested, for the first time, as a cathode component in wastewater-fed air chamber MFCs. Both materials were tested in the presence and absence of light to evaluate their photocatalytic behavior. The best performance in terms of electricity production was obtained for the MFC containing the Co-modified POM-based cathode, which showed a maximum power of 418.15 mW/m2 equivalent to 331 mW per cubic meter of treated wastewater, and a maximum COD removal percentage of 97% after 96 h of MFC operation. Co- and Fe-modified POMs had outstanding optical behavior with lower energy... [more]

Providing real-time information on the chemical properties of hydrocracking bottom oil (HBO) as the feedstock for ethylene cracker while minimizing processing time, is important to improve the real-time optimization of ethylene production. In this study, a novel approach for estimating the properties of HBO samples was developed on the basis of near-infrared (NIR) spectra. The main noise and extreme samples in the spectral data were removed by combining discrete wavelet transform with principal component analysis and Hotelling’s T2 test. Kernel partial least squares (KPLS) regression was utilized to account for the nonlinearities between NIR data and the chemical properties of HBO. Compared with the principal component regression, partial least squares regression, and artificial neural network, the KPLS model had a better performance of obtaining acceptable values of root mean square error of prediction (RMSEP) and mean absolute relative error (MARE). All RMSEP and MARE values of densi... [more]

When it comes to lightweight design of automotive wheels, hybrid designs consisting of a carbon composite wheel rim and a metallic, e.g., aluminum alloy, wheel disc offer significant potential. However, the conventionally used bolted joint between the two parts is complex and requires compromises in lightweight design due to the additional mechanical elements. Within this research, an adhesive joint for a hybrid wheel is developed in order to demonstrate its performance and lightweight potential. The main challenges are the reliable resistance against high structural loads during different load cases, as well as the residual stresses in the joint due to different thermal expansion rates of the composite and aluminum material. The developed joint combines an adhesive bond with a form-fitted geometry while still enabling an assembling process of the wheel disc in rotational direction. In addition, adaptations of the fiber layup in the rim area significantly reduce the thermal residual st... [more]

The chemical industry includes a wide range of factories focused on obtaining final products as: (i) plastics; (ii) chemical fibers; (iii) rubber; (iv) perfumery and cosmetic products; and (v) cleaning products. Although the level of safety in the activities and installations of this sector is very high, the use of dangerous substances implies an increased risk of suffering an accident involving the emission of hazardous substances, as well as endangering the safety of workers. In the case of the manufacture of softeners, the presence of isopropanol (C3H8O), and dimethyl sulfate (CH3)2SO4), have been reported to be the accident cause in most of the cases. The European accident database (eMars) reported an accident in which the presence of impurities of nickel (Ni) in the hydrogenated tallow used as raw material for softener production may have increased thermal reactivity and the chances of spontaneous combustion. This paper analyzes the results obtained with the Maciejasz Index (MI) t... [more]

Since the 1950s, plastic production has skyrocketed. Various environmental and human activities are leading to the formation and accumulation of microplastics (MPs) in aquatic and terrestrial ecosystems, causing detrimental effects on water, soil, plants, and living creatures. Wastewater treatment plants (WWTPs) are one of the primary MP management centers meant to check their entry into the natural systems. However, there are considerable limitations in effectively capturing, detecting, and characterizing these MPs in the inlet and outlet of WWTPs leading to “unaccounted MPs” that are eventually discharged into our ecosystems. In order to assess the holistic picture of the MPs’ distribution in the ecosystems, prevent the release of these omitted MPs into the environment, and formulate regulatory policies, it is vital to develop protocols that can be standardized across the globe to accurately detect and account for MPs in different sample types. This review will cover the details of c... [more]

This study aimed to purify and partially characterize a keratinolytic protease produced by Bacillus sp. P45 through bioconversion of feather meal. Crude protease extract was purified using a sequence of an aqueous two-phase system (ATPS) in large volume systems (10, 50, and 500 g) to increase obtaining purified enzyme, followed by a diafiltration (DF) step. Purified protease was characterized in terms of protein profile analysis by SDS-PAGE, optimum temperature and pH, thermal deactivation kinetics at different temperatures and pH, and performance in the presence of several salts (NaCl, CaCl2, MnCl2, CaO, C8H5KO4, MgSO4, CuSO4, ZnSO4, and FeCl3) and organic solvents (acetone, ethanol, methanol, acetic acid, diethyl ether, and formaldehyde). ATPS with high capacities resulted in purer protease extract without compromising purity and yields, reaching a purification factor up to 2.6-fold and 6.7-fold in first and second ATPS, respectively, and 4.0-fold in the DF process. Recoveries were u... [more]

Aim: To formulate and characterize a palm-oil-in-water-based α-Mangostin nano-emulsion (PO-AMNE) endodontic irrigant, in order to evaluate its antibacterial efficacy against Enterococcus faecalis, Staphylococcus epidermidis, and Candida albicans biofilms, as well as its capacity to remove smear layer. Methods: The solubility of α-Mangostin in various oils was determined and selected, surfactants and co-surfactants were used for the nano-emulsion trial. PO-AMNE was prepared and optimized. The MIC was performed, and the antimicrobial efficacy was estimated against biofilms. The optimized 0.2% PO-AMNE irrigant antimicrobial efficacy in a tooth model was done using colony-forming units. The treated teeth were processed by scanning electron microscopic examination for debris and smear layer removal. An Alamar Blue assay was used to evaluate cell viability. The optimization of the PO-AMNE irrigant was performed using Box−Behnken statistical design. Results: The optimized 0.2% PO-AMNE irrigan... [more]

Since the requirement for a material cutting process occurs in a wide variety of applied contemporary manufacturing, the cutting stock problem plays a critical role in optimizing the amount of raw material utilized in everyday production operations. In this paper, we address the two-dimension strip-cutting problem and implement the graph compression technique to improve the performance of the arc-flow formulation. The number of variables of the obtained mathematical model are substantially reduced. A comparative study on a large set of benchmark instances shows that our compressed model yields very good results for the non-unitary item demand case in contrast to the state-of-the-art mathematical models. Moreover, improved bounds are provided for 24 unsolved benchmark instances, among which 8 have been solved to optimality.

Dyes used in textiles, foods, cosmetics, and chemicals have become a major environmental pollution issue around the world. To address this issue, a number of technologies have been created to remove these pollutants from the environment. Due to their superior properties at nanoscale, numerous nanomaterials have been applied to remove dyes from polluted waters. This research presents the findings of the development of bentonite nano zero-valent iron (B-nZVI) for the treatment of synthetic cationic dyes. This study has three objectives: (i) to produce bentonite nano zero-valence iron (B-nZVI), (ii) to characterize its adsorbents (B-nZVI), (iii) to characterize its adsorption capacity. Four main tests were used for this purpose: (i) a physical test (Brunauer−Emmett−Teller (BET) surface area), (ii) a chemical test (cation exchange capacity (CEC) and X-ray fluorescence (XRF)), (iii) morphology (field emission scanning electron microscopy (FESEM) and (iv) mineralogy (Fourier transform infrar... [more]

Acoustic emission (AE) technology has the advantage of online localization to study the change laws of AE in the process of coal spontaneous combustion and to reveal the generation mechanisms of AE signal during the process of heating and rupture of coal body from a microscopic perspective. This paper first constructs a large-scale coal spontaneous combustion AE test system and conducts experimental tests on the AE signal in the process of coal spontaneous combustion. The results show that with the increase of temperature in the process of coal spontaneous combustion, the AE signal shows a trend of increasing fluctuations. Low-temperature nitrogen adsorption experiments studied the pore structure of coal spontaneous combustion, and the results showed a correspondence between the development of pores and the temperature of coal spontaneous combustion. Further, through the analysis of the evolution of the pore structure of coal through Fourier transform and fractal theory, it is found th... [more]

We investigated the effect of electro-induced multi-gas modification (EIMGM) duration on the adhesion and wear resistance of PET and LDPE polymer substrates used in the printing industry. It was found that EIMGM increases the polar component and the complete free surface energy from 26 to 57 mJ/m2 for LDPE and from 37 to 67 mJ/m2 for PET (due to the formation of oxygen-containing groups on the surface of the materials). Although the degree of textural and morphological heterogeneity of the modified LDPE increased more than twice compared to the initial state, it is not still suitable for application as a substrate in extrusion 3D printing. However, for PET, the plasma-chemical modification contributed to a significant increase (~5 times) in filament adhesion to its surface (due to chemical and morphological transformations of the surface layers) which allows for using the FFF technology for additive prototyping on the modified PET-substrates.

In recent years, China has entered a period of rapid urban development, but most of the cities with rapid development still have ground hardening, which makes it difficult for rainwater to penetrate and discharge. In order to achieve the rapid drainage of accumulated water in the city, nanotechnology was introduced, and permeable concrete based on NC and NS nanomaterials was proposed. Combined with finite element analysis, the permeable properties and mechanical properties of permeable concrete mixed with nanomaterials were analyzed. A comprehensive performance analysis of pervious concrete shows that the viscosity of permeable concrete mixed with nanomaterials is significantly higher than that of non-mixed pervious concrete, and the permeability coefficient of permeable concrete mixed with nanomaterials can reach 0.43 cm/s. A finite element analysis shows that the incorporation of nanomaterials can improve the compressive strength of permeable concrete. At the same time, under a rainw... [more]

Sodium-ion batteries (SIBs) serve as the most promising next-generation commercial batteries besides lithium-ion batteries (LIBs). Hard carbon (HC) from renewable biomass resources is the most commonly used anode material in SIBs. In this contribution, we present a review of the latest progress in the conversion of waste biomass to HC materials, and highlight their application in SIBs. Specifically, the following topics are discussed in the review: (1) the mechanism of sodium-ion storage in HC, (2) the HC precursor’s sources, (3) the processing methods and conditions of the HCs production, (4) the impact of the biomass types and carbonization temperature on the carbon structure, and (5) the effect of various carbon structures on electrochemical performance. Data from various publications have been analyzed to uncover the relationship between the processing conditions of biomass and the resulting structure of the final HC product, as well as its electrochemical performance. Our results... [more]

Resilience is regarded as an essential design objective of a wide range of systems in modern society. This work is based on a vision that networks of mobile energy storage systems could provide an alternative off-grid power system design for rural and underdeveloped regions. To evaluate the resiliency of networked energy storage systems under overload failure, a model of concurrent cascading failure and healing processes is developed and demonstrated. Two resilience metrics are used to evaluate the resilience of a real-world network, namely the recovery level at a specified time and the recovery time. The simulations generate system trajectories at each time step. We explore the dependence of the system behavior on different model parameters that capture key recovery strategies. The success probability of the recovery of a failed node needs to be high enough for the network to restore its original functionality. Similarly, the increase in recovery budget parameter also leads to faster... [more]

Fast-growing grass is a biomass material with characteristics such as high temperature and drought resistance; rapid growth and development; and repeated germination and cutting. Therefore, it is a popular biomass fuel. It is required that the pollutants produced during the biomass combustion process are appropriately controlled. For this purpose, our study analyses the influence of combustion temperature and calcium oxide (CaO) on the nitrogen oxides (NOx) and carbon monoxide (CO) emission characteristics of fast-growing grass combustion using the biomass combustion flue gas analysis and testing platform. The results of our analysis revealed that CaO additive can simultaneously reduce the peak and total NOx emissions at 750 °C. Particularly, 5% CaO demonstrated a significant control effect on the NOx emission from the fast-growing grass combustion process, with a peak and total emissions reduction of 47.05% and 56.81%, respectively. In addition, with an increase in temperature, the CO... [more]

Antibiotic pollution has become a serious concern due to the extensive use of antibiotics, their resistance to removal, and their detrimental effects on aquatic habitats and humans. Hence, developing an efficient antibiotic removal process for aqueous solutions has become vital. Amoxicillin (Amox) is one of the antibiotics that has been efficiently removed from an aqueous solution using hydroxyapatite nanoparticles (HAP NPs). The current study synthesizes and utilizes hydroxyapatite nanoparticles as a cost-effective adsorbent. Adsorbent dose, pH solution, initial Amox concentration, equilibrium time, and temperature are among the factors that have an evident impact on Amox antibiotic adsorption. The (200) mg dose, pH (5), temperature (25) °C, and time (120) min are shown to be the best-optimized values. The nonlinear Langmuir’s isotherm and pseudo-second-order kinetic models with equilibrium capacities of 4.01 mg/g are highly compatible with the experimental adsorption data. The experi... [more]

Biocatalysis entails the use of enzymes, which are catalytically active proteins, to speed up reactions so that products can be obtained swiftly and accurately [...]

To improve the understanding of the mixing performance of double shaft, batch-type paddle mixers, the discrete element method (DEM) in combination with a Plackett−Burman design of experiments simulation plan is used to identify factor significance on the system’s mixing performance. Effects of several factors, including three material properties (particle size, particle density and composition), three operational conditions (initial filling pattern, fill level and impeller rotational speed) and three geometric parameters (paddle size, paddle angle and paddle number), were quantitatively investigated using the relative standard deviation (RSD). Four key performance indicators (KPIs), namely the mixing quality, mixing time, average mixing power and energy required to reach a steady state, were defined to evaluate the performance of the double paddle mixer. The results show that the material property effects are not as significant as those of the operational conditions and geometric param... [more]

Optimizing coal blending is important for high-quality development of coking industries, among which deep understanding of relationships between coal characteristics and coke quality is critical. This work selected four typical coals from Shanxi Province in China to investigate influences of their structures and properties on coke quality. Although these samples belong to coking coals, the mechanical strength and thermal strength of the corresponding cokes are quite different. Macerals in coals, especially vitrinite, have significant effect on thermal strength of cokes. The thermal strength of coke B is better than coke A, because coal A mainly contains desmocollinite and coal B has more telocollinite. The CSR of coke B, C and D is higher than 60%, indicating they possess good thermal property. In the coking process, relatively low initial softening temperature (100 °C), smooth fluidity region and appropriate maximum fluidity is helpful to improve coke quality based on Gieseler fluidit... [more]

Commercially pure aluminium is employed in several industrial applications. On some applications, the surface of this material needs to be functionalised. Laser surface texturing is a powerful tool to functionalise aluminium and aluminium alloy surfaces. However, the corrosion resistance of the laser textured aluminium alloy can be modified, and this has rarely been investigated in the literature. Consequently, the corrosion resistance of the laser textured commercially pure aluminium in saltwater was evaluated using several electrochemical techniques: asymmetric electrochemical noise, potentiodynamic polarisation curve and electrochemical impedance spectroscopy. Although the non-laser surface textured samples possessed higher kinetic corrosion resistance in the first hours of immersion, the corrosion mechanism (process group of the corrosion) was found to be more unstable than the laser textured specimens. The oxidised layer of the textured samples was also nobler than the native pass... [more]