Pretreatment to improve the enzymatic digestibility of highly crystallized lignocellulosic biomass is essential in biorefinery processes. This study investigates the combination of lignocellulose pretreatment with continuous alkaline single-screw extrusion and ultrasonication for biosugar production. Miscanthus sacchariflorus was used because it is a promising bioenergy crop. The results show that ultrasonication with continuous alkaline pretreatment increased the enzymatic digestibility of carbohydrates and reduced the use of chemicals during pretreatment. An hour of ultrasonication following 0.2 M NaOH (2.25 mol-NaOH/kg-biomass) continuous alkaline pretreatment resulted in a 6.7% increase in total biosugar production (83.1% of theoretical yield), a decrease of up to 26.1% in chemical usage, and a 17.0% increase in lignin removal compared with the case without ultrasonication. The developed method can be considered an effective and eco-friendly approach to the production of bio-based... [more]

Biofuels used as biocomponents for transport fuels should meet quality requirements. Their properties have a significant impact on the proper functioning of the engine supply system and the wear of its components. Changes in the performance of biofuel functionality may already occur during storage. Therefore, the present study aimed to evaluate changes in selected rheological and tribological parameters of higher fatty acid esters depending on the time and method of their storage by considering different types of substrates used for their production. The presence of possible microbiological contamination, which may affect the examined parameters of biofuels, was also analyzed. The dynamic viscosity of the biofuels tested changed depending on the substrate used. The biofuel produced from waste oil had the highest viscosity. Tribological studies show that both the linear wear of samples and the friction moment were higher after the storage period. The acid number of the esters did not ex... [more]

The demand for alternative sources of clean, sustainable, and renewable energy has been a focus of research around the world for the past few decades. Microbial/enzymatic biofuel cells are one of the popular technologies for generating electricity from organic substrates. Currently, one of the promising fuel options is based on glucose due to its multiple advantages: high energy intensity, environmental friendliness, low cost, etc. The effectiveness of biofuel cells is largely determined by the activity of biocatalytic systems applied to accelerate electrode reactions. For this work with aerobic granular sludge as a basis, a nitrogen-fixing community of microorganisms has been selected. The microorganisms were immobilized on a carbon material (graphite foam, carbon nanotubes). The bioanode was developed from a selected biological material. A membraneless biofuel cell glucose/oxygen, with abiotic metal catalysts and biocatalysts based on a microorganism community and enzymes, has been d... [more]

Ethanol is a widely produced fuel, as well as a fuel additive. Its price is closely related to the price of gasoline, its major substitute. This paper focuses on the impacts of the related variables on regional ethanol prices. Additionally, the length of the price dataset made it possible to isolate the impacts of COVID-19 on the ethanol prices. Using multiple regression and Confirmatory Factor Analyses, we found no significant correlation between the European and US ethanol prices because the major influencing factors were regionally different. In the case of the European ethanol markets, the positive factors were wheat, maize, and potassium chloride prices, while the European sugar and diammonium phosphate prices were negative. In the US markets, gasoline, sugar, and most of the artificial fertilizer prices were positive, while wheat prices were negative. Based on factor analysis, artificial fertilizers and maize factors proved to be important to the European markets, while US ethano... [more]

A simple ultrasonic radiation method was employed for the preparation of zinc and cadmium sulfide solid solution (ZnxCd1−xS; x = 0−0.25 wt.%) with the aim to investigate its efficiency for H2 production via a visible light-driven water-splitting reaction. The catalyst characterization by X-ray diffraction confirmed the formation of solid solution (ZnxCd1−xS) between CdS and ZnS phases. All catalysts exhibited hierarchical morphology (from SEM and TEM) formed by aggregated nanoparticles of ZnxCd1−xS solid solution with crystals showing mainly (111) planes of cubic CdS phase. The crystal size linearly decreased with an increase in Zn incorporation in the crystal lattice (from 4.37 nm to 3.72 nm). The ZnxCd1−xS photocatalysts showed a gradual increase in the H2 evolution, with an increase in the Zn concentration up to 0.2 wt.% making the most effective Zn0.2Cd0.8S catalyst toward H2 production. From the catalyst activity−structure correlation, it has been concluded that the twin-like CdS... [more]

Metal-organic frameworks (MOFs) and covalent organic frameworks (COFs) are two innovative classes of porous coordination polymers. MOFs are three-dimensional materials made up of secondary building blocks comprised of metal ions/clusters and organic ligands whereas COFs are 2D or 3D highly porous organic solids made up by light elements (i.e., H, B, C, N, O). Both MOFs and COFs, being highly conjugated scaffolds, are very promising as photoactive materials for applications in photocatalysis and artificial photosynthesis because of their tunable electronic properties, high surface area, remarkable light and thermal stability, easy and relative low-cost synthesis, and structural versatility. These properties make them perfectly suitable for photovoltaic application: throughout this review, we summarize recent advances in the employment of both MOFs and COFs in emerging photovoltaics, namely dye-sensitized solar cells (DSSCs) organic photovoltaic (OPV) and perovskite solar cells (PSCs). M... [more]

Curing minor leaks and restoring the integrity of a wellbore in a safe and economical way is always challenging in oil and gas production. In this work, a composite pressure-activated sealant, combined with liquid and solid sealing materials, was prepared via the demulsification approach. The structure, morphology, and size distribution of key particulates in the sealant were examined, and the in-situ self-adaptive sealing property was examined with a specially design dynamic sealing detector. The results indicated that the pressure-activated sealant was a multi-dispersed phase system, and the dispersed colloid particles were regular in shape and had a narrow size distribution of 300−400 μm. The solid sealing materials were introduced to construct a composite pressure-activated sealant, and the sealing capability can be markedly reinforced by cooperativity of liquid and solid sealing materials. A mechanochemical coupling model was put forward to rationalize the dynamic sealing process.... [more]

In this study, RF-based un-doped and nitrogen-doped aerogels were produced by polymerisation reaction between resorcinol and formaldehyde with sodium carbonate as catalyst and melamine as the nitrogen source. Carbon/activated carbon aerogels were obtained by carbonisation of the gels under inert atmosphere (Ar) followed by activation of the carbons under CO2 at 800 °C. The BET analysis of the samples showed a more than two-fold increase in the specific Surf. area and pore volume of carbon from 537 to 1333 m2g−1 and 0.242 to 0.671 cm3g−1 respectively after nitrogen doping and activation. SEM and XRD analysis of the samples revealed highly porous amorphous nanostructures with denser inter-particle cross-linked pathways for the activated nitrogen-doped carbon. The X-Ray Photoelectron Spectroscopy (XPS) results confirmed the presence of nitrogen and oxygen heteroatoms on the Surf. and within the carbon matrix where improvement in wettability with the drop in the contact angle from 123° to... [more]

Rock mass is a medium created through processes that have lasted over four billion years, and its intrinsic feature is the variability of the parameters that describe it. A particularly high variability of mechanical parameters is observed in Carboniferous sedimentary and metamorphic rocks. The mechanical properties, especially the rock mass strength, are essential for the design and maintenance of the stability of excavations conducted in it and for the safe conduct of mining operations. This article presents the test results confirming the random variability of the mechanical parameters of the rock mass. The second part of the article presents the results of numerical simulations mapping the Carboniferous rock mass along with a 1000 m deep tunnel excavation protected by steel arch supports. Numerical simulations were carried out for models with different variability coefficients of strength and deformation parameters, and the obtained results were analyzed in terms of damage zones an... [more]

In this study, the process of the solidification of a PCM (phase change material) liquid in an annular space was analytically investigated with the use of a simplified quasi-steady-state model. This model described the phase change phenomenon with the cylindrical solidification front and with the solidification liquid overheated above the solidification temperature. One of the important novelties of the applied model was the determination of the coefficient of the heat transfer between the liquid and the solidified layer on the solidification surface, which was calculated as a function of the location of the solidification front. A method for calculating the variable coefficient of heat transfer on the surface of the solidification front during the solidification process is presented. The contact layer between the cold wall and the solidified layer was incorporated into the model and played an important role. The theoretical analytical method describing the solidification process based... [more]

Lowering the platinum group metal content of oxygen reduction reaction catalysts is among the most prevalent research focuses in the field. This target is herein approached through supported Pd(II) complexes. Starting from a commercial macrocycle, a new ligand is synthesized, its solution behavior and binding properties briefly explored (potentiometry, UV-Vis) and then used to prepare a new catalyst. A supramolecular approach is used in order to obtain homogeneous decoration of carbon nanotubes surfaces, fostering novel possibilities to access single-ion active sites. The novel catalyst is characterized through X-ray photoelectron spectroscopy and scanning transmission electron microscopy and its promising oxygen reduction reaction performance is evaluated via rotating ring-disk electrode and rotating disk electrode in half-cell studies.

In this study, experimental apparatus of desiccant dehumidification was developed at lab-scale, using silica gel as a desiccant material. Experimental data were obtained at various ambient air conditions, while focusing the climatic conditions of Multan (Pakistan). A steady-state analysis approach for the desiccant dehumidification process was used, and thereby the slope of desiccant dehumidification line on psychrometric chart (ϕ*) was determined. It has been found that ϕ* = 0.22 in case of silica gel which is lower than the hydrophilic polymeric sorbent, i.e., ϕ* = 0.31. The study proposed two kinds of systems, i.e., (i) standalone desiccant air-conditioning (DAC) and (ii) Maisotsenko-cycle-assisted desiccant air-conditioning (M-DAC) systems. In addition, two kinds of desiccant material (i.e., silica gel and hydrophilic polymeric sorbent) were investigated from the thermodynamic point of view for both system types, using the experimental data and associated results. The study aimed t... [more]

Chemical composition influences the calorific power of wood, mainly due to the calorific power of structural compounds and extractives. Heat treatment changes the chemical composition of treated wood. This work studies the relationship between chemical composition and calorific power improvement by heat treatment. Samples were heat-treated by the ThermoWood process ® for 1 h and 2 h. High heating value (HHV) and chemical composition; lignin, cellulose, hemicelluloses and extractives in dichloromethane, ethanol, and water were determined. The HHV of untreated wood ranged between 18.54−19.92 MJ/kg and increased with heat treatment for all the tested species. A positive linear correlation was found between HHV and Klason lignin (R2 = 0.60). A negative trend was observed for holocellulose, cellulose, and hemicelluloses content against HHV, but with low determination coefficients for linear regression. The best adjust for polysaccharides was found for hemicelluloses content. A positive corr... [more]

Thermophysical properties of HFE-356mmz in the vapor phase were measured by means of an acoustic-microwave resonance method. HFE-356mmz, which is 1,1,1,3,3,3-hexafluoro-2-methoxypropane in chemical name, is expected to be used as a working fluid with low global warming potential for the Organic Rankine cycle (ORC). The sound velocity and dielectric permittivity were simultaneously measured by using a cylindrical acoustic-microwave resonator. The sound velocity data were analyzed to obtain the ideal-gas heat capacity at constant pressure. The integral of the ideal-gas heat capacity as a function of temperature derives the ideal-gas enthalpy, which is a fundamental and important energy property to simulate the thermodynamic cycle. Similarly, the analysis of the dielectric permittivity data leads to information on the ideal-gas molar polarizability, dipole moment, and density. The acquired thermophysical properties of HFE-356mmz were compared to those of R-245fa and n-pentane, which are t... [more]

A thermal model is proposed to analyze the performance of an indirect solar dryer (ISD) with latent heat storage using phase change material (PCM). The estimations are compared with experimental data presented in the scientific literature taken in real conditions. The validated thermal model is used in order to address a comprehensive analysis of the performance of the ISDs under the same operation conditions, the model is able to estimate the temperatures of glass cover, absorber plate, PCM, useful heat, thermal and storage efficiencies, and variables that are difficult to measure experimentally such as liquid fraction, heat losses, and accumulated energy of the ISDs. Three study cases are considered: Case 1 consists of two collectors with and without alternating nocturnal and diurnal operation (benchmarking case). Case 2 and 3 consist in a unique collector operating continuously for 24 h with PCM and without PCM, respectively. It was determined that the use of PCM in ISD increased th... [more]

The present study explores the entropy generation, flow, and heat transfer characteristics of a dissipative nanofluid in the presence of transpiration effects at the boundary. The non-isothermal boundary conditions are taken into consideration to guarantee self-similar solutions. The electrically conducting nanofluid flow is influenced by a magnetic field of constant strength. The ultrafine particles (nanoparticles of Fe3O4/CuO) are dispersed in the technological fluid water (H2O). Both the base fluid and the nanofluid have the same bulk velocity and are assumed to be in thermal equilibrium. Tiwari and Dass’s idea is used for the mathematical modeling of the problem. Furthermore, the ultrafine particles are supposed to be spherical, and Maxwell Garnett’s model is used for the effective thermal conductivity of the nanofluid. Closed-form solutions are derived for boundary layer momentum and energy equations. These solutions are then utilized to access the entropy generation and the irrev... [more]

This paper presents a detailed geological map at the 1:20,000 scale of the Tocomar basin in the Central Puna (north-western Argentina), which extends over an area of about 80 km2 and displays the spatial distribution of the Quaternary deposits and the structures that cover the Ordovician basement and the Tertiary sedimentary and volcanic units. The new dataset includes litho-facies descriptions, stratigraphic and structural data and new 234U/230Th ages for travertine rocks. The new reconstructed stratigraphic framework, along with the structural analysis, has revealed the complex evolution of a small extensional basin including a period of prolonged volcanic activity with different eruptive centres and styles. The geological map improves the knowledge of the geology of the Tocomar basin and the local interplay between orogen-parallel thrusts and orogen-oblique fault systems. This contribution represents a fundamental support for in depth research and also for encouraging geothermal exp... [more]

Phosphorus (P) recovery from sewage sludge ash (SSA) is one of the most promising approaches of phosphate rock substitution in mineral fertilizers and might be a sustainable way to secure supply of this raw material in the future. In the current investigation, the process of thermochemical treatment of SSA was applied to SSA coming from selected mono-incineration plants of municipal sewage sludge in Poland (Cracow, Gdansk, Gdynia, Lodz, Kielce and Szczecin). The Polish SSA was thermochemically converted in the presence of sodium (Na) additives and a reducing agent (dried sewage sludge) to obtain secondary raw materials for the production of marketable P fertilizers. The process had a positive impact on the bioavailability of phosphorus and reduced the content of heavy metals in the obtained products. The P solubility in neutral ammonium citrate, an indicator of its bioavailability, was significantly raised from 19.7−45.7% in the raw ashes and 76.5−100% in the thermochemically treated S... [more]

A series of impact compression tests were conducted to study the breakage characteristics of magnetite, as well as the impact pressure on its strain rate and dynamic compressive strength. The dynamic mechanical properties and fragmentation size distribution of magnetite under diverse impact loads and cyclic impact were investigated, with fractal theory as a basis and split Hopkinson pressure bar (SHPB). Breakage methods were also employed to analyze the fracture morphology of magnetite. According to the result, the fractal dimension can reflect the distribution of fragments in various sizes. If the strain rate increases, the fractal dimension will be larger, the fragment size will be finer, and the fragmentation degree will be more influential. A micro-analysis of SEM images demonstrates that the fracture morphology is determined by mineral properties. Under low load cyclic impact, intergranular fracture is the main fractography. Besides, the intergranular fracture will be changed to a... [more]

In recent years, graphene-based nanomaterials have been increasingly and widely used in numerous industrial sectors. In the drilling industry, graphene oxide in cement slurry has significantly improved the mechanical parameters of cement composites and is a future-proof solution. However, prior to placing it in a borehole ring space, cement slurry must feature appropriate fluidity. Graphene oxide has a significant influence on rheological parameters. Therefore, it is necessary to study graphene oxide’s influence on the rheological parameters of cement slurries. Thus, this paper presents rheological models and the results of studies on rheological parameters. A basic cement slurry and a slurry with a latex addition were used. The latex admixture was applied at concentrations of 0.1%, 0.03%, and 0.06%. In total, studies were carried out for six slurries with graphene oxide and two basic slurries. The obtained results of studies on the slurries with graphene oxide were compared with the c... [more]

High voltage spark discharge (HVSD) could generate strong pressure waves that can be combined with a rotary drill bit to improve the penetration rate in unconventional oil and gas drilling. However, there has been little investigation of the effect of electrical conductivity on rock damage and the fragmentation mechanism caused by HVSD. Therefore, we conducted experiments to destroy cement mortar, a rock-like material, in water with five conductivity levels, from 0.5 mS/cm to 20 mS/cm. We measured the discharge parameters, such as breakdown voltage, breakdown delay time, and electrical energy loss, and investigated the damage mechanism from stress waves propagation using X-ray computed tomography. Our study then analyzed the influence of conductivity on the surface damage of the sample by the pore size distribution and the cumulative pore area, as well as studied the dependence of internal damage on conductivity by through-transmission ultrasonic inspection technique. The results indic... [more]

Agricultural residue is a readily available biomass source for making biofuels. However, complex structure along with low calorific value makes it reluctant to be utilized. This necessitates the pretreatment of biomass to improve its accessibility. In this study, rice straws were treated with saturated steam at 180−200 °C for 5−10 min and pelletized. Results indicated that the pretreatment process could effectively improve the calorific values and enhance the hydrophobicity of the rice straws. The steam explosion process changed the content of chemical components in the biomass materials. With the increase of reaction temperature and retention time, the content of cellulose, hemicelluloses and lignin declined. Comparedwith the raw materials, there was an increase in the calorific value from 16.24 MJ/kg to 17.26 MJ/kg for the steam treated straws. For moisture sorption test under the condition of 30 °C and 90% relative humidity, the equilibrium moisture content dropped from 21% for untr... [more]

In this paper, we present a new approach for the analysis of the dependence of construction costs on the geometric shape of a building. Instead of difficult or even impossible-to-establish uniform prices and costs, we propose a cost analysis concerning the amount of materials needed for construction. We show that the basic parameters are the base area of the building (plan), assumed in the study as the building area, and the area of the external walls of the building. The amount of consumption of most materials is proportional to the base area and the area of the external walls. The materials required for construction consume large amounts of energy during their manufacture. Therefore, shape optimization is not only economically significant for the investor but is also important in terms of the energy consumption, i.e., embodied energy. We propose a set of indicators to help a designer optimize the shape of the building at the initial design stage.

Hydrate-based CO2 capture from large emission sources is considered a promising process for greenhouse gas mitigation. The addition of nanoparticles may promote or inhibit the formation of hydrates. In this work, CO2 hydrate formation experiments were performed in a dual-cell high-pressure reactor. Non-modified, hydrophilic modified and hydrophobic modified aluminum oxide (Al2O3) nanoparticles at different concentrations were added to assess their promoting or inhibitory effects on CO2 hydrate formation. The equilibrium temperature and pressure, induction time, and total gas consumption during CO2 hydrate formation were measured. The results show that the presence of Al2O3 nanoparticles exerts little effect on the phase equilibrium of CO2 hydrates. Under the experimental conditions, the addition of all Al2O3 nanoparticles imposes an inhibitory effect on the final gas consumption except for the 0.01 wt% addition of hydrophilic modified Al2O3 nanoparticles. The induction time required fo... [more]

In this paper, we developed an effective method for purifying oil sludge using a sorbing electrochemical matrix and assessed the prospects of this method in comparison with conventional hydrocracking. We synthesized Ni-W supported hydrocracking catalysts with different morphology and studied their activity under various conditions, we compared the obtained catalysts with commercial catalyst SGK-5. We demonstrated that the introduction of a secondary mesoporous structure in the catalyst leads to an increase in the yield of light fractions to 52 wt.%. The possibility is demonstrated to obtain hydrocarbons from reservoir oil sludge, dispersed into an aqueous solution of detergent, by the method of low-temperature hydrogenation in sorbing electrochemical matrices. The obtained product was characterized by low viscosity, low content of transition metals (<320 ppm), and sulphur (<260 ppm).