This paper provides an analysis of a designed underground station infrastructure for vacuum tube high-speed trains for the planned mega transport hub in Poland. The potential of integrating the infrastructure of the station building with sealed low-pressure tubes system is analyzed. The Solidarity Transport Hub Poland is a planned mega hub to be located in Baranów Municipality, Poland, which is comprised of an airport, an airport city, a road, and railway infrastructure. It is to be integrated with the first route of vactrains in Poland. The aim of this paper is to design a hyperloop station building adequate for the advanced technology of low-pressure high-speed trains. Designing a hyperloop station is not trivial, due to technological aspects which have not been hitherto present in airport or railway planning and design, such as low-pressure zones or airlocks which determine possible passenger paths and evacuation roads. Both the mega airport and Polish hyperloop are in the planning... [more]

Slotted liners are widely used in steam-assisted gravity drainage (SAGD) wells to control sand production and sustain wellbore productivity. The slotted liner can provide desirable performance when appropriately designed. A literature review indicates a limited number of studies that offer design criteria specifically for SAGD wells. Moreover, past criteria seem to neglect some key factors, which may lead to inadequate slot design. This paper proposes a set of graphical design criteria for slotted liners in SAGD production wells, using prepacked sand retention testing (SRT) data. The SRT is designed to incorporate several essential factors that are not present in the past design criteria, such as slot density, steam breakthrough, and particle size distribution (PSD). The proposed design criteria are presented graphically for normal and aggressive conditions, where the aggressive condition accounts for the potential occurrence of the steam breakthrough. It is found that the upper bound... [more]

Thermal performance enhancement in microchannel heat sinks has recently become a challenge due to advancements in modern microelectronics, which demand compatibility with heat sinks able to dissipate ever-increasing amounts of heat. Recent advancements in manufacturing techniques, such as additive manufacturing, have made the modification of the microchannel heat sink geometry possible well beyond the conventional rectangular model to improve the cooling capacity of these devices. One such modification in microchannel geometry includes the introduction of secondary flow channels in the walls between adjacent mainstream microchannels. The present study computationally models secondary flow channels in regular trapezoidal and parallel orientations for fluid circulation through the microchannel walls in a heat sink design. The heat sink is made of silicon wafer, and water is used as the circulating fluid in this study. Continuity, momentum, and energy equations are solved for the fluid fl... [more]

In the era of expensive energy carriers and care for the climate, companies are keen to take action towards bolstering energy efficiency. Businesses often lack data on actual energy consumption to date, are rarely equipped with adequate analytical tools, and do not have the know-how regarding the transition itself. Developing energy efficiency management (EEM) for a given enterprise requires many steps, which ultimately unleash analytical potential and seamlessly integrate the EEM framework with the business model of a given company. This study scrutinizes and formalizes a reference process of pilot EEM implementation that involves external business partners in a multi-facility organization. The process is tailored to the specificity of the company’s operations as well as its technical and management capabilities regarding energy efficiency. The proposed approach, phased in time and involving multiple stakeholders, should be especially useful for practitioners running EEM-related proje... [more]

Currently, there is increasing research interest in harnessing wind energy for power generation by means of non-conventional electrical machines e.g., flux-reversal machines. The flux reversal machine is usually designed using scarce rare−earth permanent magnet material which may be unattractive in terms of machine cost. In this study, an attempt is made to re-design the flux reversal machine with non-rare-earth ferrite permanent magnet for wind energy applications. Because these machines possess high cogging torque, which results in vibration and noise, that are detrimental to the machine performance, especially at low speeds, a novel combined skewed and circumferential rotor pole pairing method is developed. The proposed cogging torque reduction method is implemented in 2-dimensional finite element analysis modeling and comparatively analyzed with other existing stand-alone methods viz., skewing, and rotor pole pairing. The results show that the proposed method led to 94.8% and 71% r... [more]

A lot of autonomous power systems have been designed and operated with different power levels and with special requirements for climatic conditions, availability, operation/maintenance cost, fuel consumption, environmental impacts, etc. In this paper a novel design of an autonomous power system with photovoltaic panels and electrochemical batteries for a shoreline electrode station is analyzed. This station will be constructed on the small island of Stachtoroi for the new high voltage direct current (HVDC) link of Attica−Crete in Greece. The general guidelines of the International Council on Large Electric Systems (CIGRE) and of the International Electrotechnical Committee (IEC) for the power system of lighting and auxiliary loads for these HVDC stations are supplied from the medium voltage or the low voltage distribution network, whereas they do not take into account the criticality of this interconnection, which will practically be the unique power facility of Crete island. The signi... [more]

In this study, the characteristics of the double quench and instantaneous power of a superconducting fault current limiter (SFCL) using two magnetically coupled windings were analyzed. In the proposed model of SFCL, two magnetically coupled windings are wound on the iron core and each winding is connected to one superconducting element. When a fault occurs, the SFCL can limit the fault current by the double quench occurrence of two superconducting elements. In order to analyze the influence of the winding direction on the fault current limiting characteristics of the proposed SFCL, two magnetically coupled windings were designed to allow the same and the reverse directions. From the simulated short circuit experiment, the currents and the voltages of two coupled windings and two superconducting elements were measured and the instantaneous power and the double quench occurrence were analyzed. It was confirmed from the experimental results analysis that the fault current limiting charact... [more]

The current lighting solutions, both in terms of design process and later implementation, are becoming more and more intelligent. It mainly arises from higher opportunities to use information technology (IT) processes for these purposes. Designs cover many aspects, from physiological to including technical. The paper describes the problems faced by any designers while creating, evaluating them, and presenting the final results of their work in a visualisation form. Development of virtual reality (VR) technology and augmented reality, which is now taking place before our eyes, makes us inclined to think how to use this reality in lighting technology. The article presents some examples of applying VR technology in various types of smart lighting designs, for interiors and outdoor objects. The performed computer simulations are compared to reality. Some surveys, in terms of visualization rendering, were carried out. In the article, the current capabilities and main limitations of virtual... [more]

Alternative energy generated from people’s footsteps in a crowded area is sufficient to power smart electronic devices with low consumption. This paper aims to present the development of an energy harvesting floor—called Genpath—using a rotational electromagnetic (EM) technique to generate electricity from human footsteps. The dynamic models of the electro-mechanical systems were developed using MATLAB®/Simulink to predict the energy performances of Genpath and help fine-tune the design parameters. The system in Genpath comprises two main parts: the EM generator and the Power Management and Storage (PMS) circuit. For the EM generator, the conversion mechanism for linear translation to rotation was designed by using the rack-pinion and lead-screw mechanism. Based on the simulation analysis, the averaged energy of the lead-screw model is greater than that of the rack-pinion model. Thus, prototype-II of Genpath with 12-V-DC generator, lead-screw mechanism was recently built. It shows bett... [more]

This work provides an investigation based on a fast estimation of the degree of unbalance (D.U.%) and the differential leakage factor (σ0) of multiphase electrical machine windings. This analysis is carried out by exploring almost 5000 combinations in terms of number of slots, pole pairs, phases and layers. The variability of the leakage factor is examined for each condition, defining an optimal region for its minimization. As a result, an extended mapping is carried out for both the degree of unbalance and the leakage factor, providing a useful tool during the early design stage of winding configurations for multiphase electric machines, even with slight asymmetries. The results obtained from this investigation are validated through finite element analysis and demonstrate that the differential leakage factor can be significantly reduced by adopting winding configurations with slight asymmetries, which also represent a valuable alternative in the electrical machine design.

In this study, a conceptual design was developed for a lead-bismuth-cooled small modular fast reactor SPARK-NC with natural circulation and load following capabilities. The nominal rated power was set to 10 MWe, and the power can be manipulated from 5 MWe to 10 MWe during the whole core lifetime. The core of the SPARK-NC can be operated for eight effective full power years (EFPYs) without refueling. The core neutronics and thermal-hydraulics design calculations were performed using the SARAX code and the natural circulation capability of the SPARK-NC was investigated by employing the energy conservation equation, pressure drop equation and quasi-static reactivity balance equation. In order to flatten the radial power distribution, three radial zones were constructed by employing different fuel enrichments and fuel pin diameters. To provide an adequate shutdown margin, two independent systems, i.e., a control system and a scram system, were introduced in the core. The control assemblies... [more]

The implementation of a three-dimensional viscous inverse design used for an axial compressor is introduced in this paper. The derivation process of the inverse design algorithm is also described in detail. Moreover, an improved blade update method and a modified relaxation factor are included to enhance the inverse design algorithm. The inverse design is built on an in-house inverse design module coupled with commercial Computational Fluid Dynamic (CFD) software NUMECATM. In contrast to analysis design, the pressure loading and the normal thickness distribution along the blade surfaces are prescribed during the process of inverse design. The numerical methods used to solve the flow field are verified using the experimental data of the transonic fan rotor NASA Rotor 67. A recovery test for the Rotor 67 is carried out to validate the developed three-dimensional inverse design tool. To explore the potential application of the inverse design system, it is then used to improve the aerodyna... [more]

A concentric annular heat pipe heat sink (AHPHS) was proposed and fabricated to investigate its thermal behavior. The present AHPHS consists of two concentric pipes of different diameters, which create vacuumed annular vapor space. The main advantage of the AHPHS as a heat sink is that it can largely increase the heat transfer area for cooling compared to conventional heat pipes. In the current AHPHS, condensation takes place along the whole annular space from the certain heating area as the evaporator section. Therefore, the whole inner space of the AHPHS except the heating area can be considered the condenser. In the present study, AHPHSs of different diameters were fabricated and studied experimentally. Basic studies were carried out with a 50 mm-long stainless steel AHPHS with diameter ratios of 1.1 and 1.3 and the same inner tube diameter of 76 mm. Several experimental parameters such as volume fractions of 10−70%, different air flow velocity, flow configurations, and 10−50 W heat... [more]

Types of tapered piles are widely applied in tank foundation consolidation, but their inherent deficiencies in design and construction limit their further promotion. Vortex compression pile is a novel nodular pile. Compared with the traditional equal-section pile, vortex compression nodular pile is featured by stronger bearing capacity and slighter settlement. In this paper, the model test results showed that vortex compression nodular pile can greatly improve the bearing capacity and reduce the settlement. Through the finite element software ABAQUS analysis the bearing characteristics of equal-section pile foundation and vortex-compression nodular pile foundation were compared. The three-dimensional solid model was established by ABAQUS finite element software. The impact of cushion modulus, cushion thickness, vertical load, pile modulus, soil modulus around the pile on the bearing capacity of the vortex-compression nodular pile foundation were studied.

In the past literature on virtual impedance to series systems, most of the discussion focused on stability without in-depth research on the system design of the series converter and the overall output impedance. Accordingly, this study takes an open-loop resonant LLC converter series-connected closed-loop Buck converter as an example. First, the conditions required for the direct connection of the small-signal model in the series, the effect of feedback compensation on the input impedance of the load stage, the operating frequency, and passive components of the two-stage converter are discussed in detail―the relationship between the matching and the output impedance. Afterwards, a mathematical model is used to discuss the effect of adding parallel virtual impedance on the output impedance of the overall series converter and then derive an optimized virtual impedance design. Finally, an experimental platform of 48 V to 12 V and maximum wattage of 96 W are implemented. The output impedan... [more]

In this paper, a permanent magnet (PM) linear memory machine is proposed for ocean wave power generation. A notable feature of this machine is its online tunable mnemonic flux. This enables it to operate efficiently in a wide speed range and makes it suitable for the variable-speed wave-power generation. Moreover, this machine has both the PMs and the windings arranged in its stator so that it does not need slip rings or brushes. The proposed machine is also robust and cost-effective because it has a simple translator of slotted steel. In this paper, the configuration and working principle of the linear memory machine are firstly introduced. The results of a parametric analysis are presented to investigate the effects of the proposed machine’s geometric parameters. The performance of the proposed machine is then analyzed using time-stepping finite element method (TS-FEM).

The present study analyzed light emitting diodes (LEDs) as an output load and used a Taylor series to describe the characteristic curve based on the exponential characteristic of voltage and current. A prototype circuit of a flyback LED driver system was established to verify whether the theory is consistent with actual results. This study focused on the exponential relationship of LED voltage and current. Conventional simulations usually used linear models to present LED loads. However, the linear model resulted in considerable error between simulation and actual characteristics. Therefore, this study employed a Taylor series to describe the nonlinear characteristic of an LED load. Through precise calculations with Mathcad computation software, the error was effectively reduced. Moreover, the process clarified the influence of temperature on LEDs, which benefited the characteristic analysis of the entire system. Finally, a realized circuit of 120 W flyback LED drivers was established... [more]

There has been increasing recognition that climate change may lead to risk of summertime overheating in UK dwellings with potentially adverse consequences for human comfort and health. This paper investigates the magnitude of summertime overheating over one month in 2017, in four new flats built to identical thermal standards, with similar occupancy patterns and located in the same block in a development in Southeast England. Both static and adaptive methods were used to assess the overheating risk, while the variation in indoor temperatures across the flats was examined through key building characteristics including floor level, glazing orientation, exposed surface area to floor area ratio (SA/FA), glazing area to floor area ratio, and ventilation. Data collection included continuous monitoring of indoor and outdoor temperature, relative humidity, CO2 levels and opening/closing of windows. Summertime overheating was found to be prevalent in all four flats but was most pronounced in tw... [more]

Photoelectrochemical water splitting is a promising pathway for solar-driven hydrogen production with a low environmental footprint. The utilization of solar concentrators to supply such water splitting devices with concentrated solar irradiation offers great potential to enhance the economic viability of water splitting at “sunny” site locations. In this work, we defined a set of functional requirements for solar concentrators to assess their suitability to power such water splitting devices, taking into account concentrator optical performance, device coupling efficiency, perceived system complexity, as well as technological costs and risks. We identified, classified and compared a broad range of existing solar concentrator design concepts. Our geometrical analysis, performed on a yearly basis with a one-minute time step, shows that two-axis tracking concentrators with water splitting devices positioned parallel to the optical aperture plane exhibit the highest potential, given the i... [more]

The article presents applications of systems with power electronic converters, high voltage transformers, and discharge chambers used for nonthermal, dielectric barrier discharge plasma treatment of a plastic surface and decontamination of organic loose products. In these installations, the inductance of the high voltage transformers and the capacitances of the electrode sets form resonant circuits that are excited by inverters. The article presents characteristic features of the installations and basic mathematical relationships as well as the impact of individual parameters of system components. These converters with their output installations were designed, built, and tested by the authors. Some of the converters developed by the authors are manufactured and used in the industry.

GaN-based power semiconductors exhibit small on-resistance and high dv/dt of the switch characteristics, thereby enabling the construction of high-efficiency, high-density semiconductor systems with fast switching and low power loss characteristics and miniaturization of passive devices. However, owing to the characteristics of GaN devices that result in them being significantly faster than other devices, the accuracy of the switching transient response significantly affects the noise or inductance in the device. Therefore, securing sufficient sensor bandwidth is considerably important for accurate current measurement in GaN-based devices. Conversely, the current sensor in the form of a non-insulated coil must secure sufficient bandwidth and overcome the tradeoff relationship with measurement sensitivity; moreover, the sensor configuration must be applicable to various power semiconductor types. This study proposes a current sensor model that applies the principle of the printed circui... [more]

In the pulping industry, thermo-mechanical pulping (TMP) as a subdivision of the refiner-based mechanical pulping is one of the most energy-intensive processes where the core of the process is attributed to the refining process. In this study, to simulate the refining unit of the TMP process under different operational states, the idea of machine learning algorithms is employed. Complicated processes and prediction problems could be simulated and solved by utilizing artificial intelligence methods inspired by the pattern of brain learning. In this research, six evolutionary optimization algorithms are employed to be joined with the adaptive neuro-fuzzy inference system (ANFIS) to increase the refining simulation accuracy. The applied optimization algorithms are particle swarm optimization algorithm (PSO), differential evolution (DE), biogeography-based optimization algorithm (BBO), genetic algorithm (GA), ant colony (ACO), and teaching learning-based optimization algorithm (TLBO). The... [more]

With the increased commercialization of high-temperature superconducting (HTS) power cables cooled using liquid nitrogen and the use of liquefied natural gas as fuel, the need for large-capacity reverse Brayton cryogenic systems is gradually increasing. In this paper, the thermodynamic design of a reverse Brayton cryogenic system with a cooling capacity of the 2 kW class at 77 K using neon as a refrigerant is described. Unlike conventional reverse Brayton systems, the proposed system uses a cryogenic turbo-expander, scroll compressor, and plate-type heat exchanger. The performance test conducted on the fabricated system is also described. The isentropic efficiency of the cryogenic turbo-expander was measured to be 86%, which is higher than the design specification. The effectiveness of the heat exchanger and the flow rate and operating pressure of the refrigerant were found to be lower than the design specifications. Consequently, the refrigeration capacity of the fabricated reverse Br... [more]

The Hyperloop has been developed using various technologies to reach a maximum speed of 1200 km/h. Such technologies include magnetic levitation technologies that are suitable for subsonic driving. In the Hyperloop, the null-flux electrodynamic suspension (EDS) system and superconducting magnets (SCMs) can perform stable levitation without control during high-speed driving. Although an EDS device can be accurately analyzed using numerical analysis methods, such as the 3D finite element method (FEM) or dynamic circuitry theory, its 3D configurations make it difficult to use in various design analyses. This paper presents a new design model that fast analyzes and compares many designs of null-flux EDS devices for the Hyperloop system. For a fast and effective evaluation of various levitation coil shapes and arrangements, the computational process of the induced electromotive force and the coupling effect were simplified using a 2D rectangular coil loop, and the induced current and force... [more]

The industrial sector is a major contributor to the economic growth of the Philippines. However, it is also one of the top consumers of energy, which is produced mainly from fossil fuels. The Philippine industrial sector must therefore be supported economically while minimizing the emissions associated with energy consumption. A potential strategy for minimizing costs and emissions is the installation of solar photovoltaic (PV) modules on the rooftops of industrial facilities, but this approach is hindered by existing energy policies in the country. In this work, we performed a techno-economic assessment on the implementation of rooftop solar PV in Philippine industrial facilities under different policy scenarios. Our study considered 139 randomly sampled industrial plants under MERALCO franchise area in the Philippines. Under the current net metering policy, 132 of the evaluated facilities were economically viable for the integration of rooftop solar PV. This corresponds to an additio... [more]