The oil and gas industry generates a significant amount of harmful greenhouse gases that cause irreversible environmental impact; this fact is exacerbated by the world’s utter dependence on fossil fuels as a primary energy source and low-efficiency oil and gas operation plants. Integration of solid oxide fuel cells (SOFCs) into natural gas plants can enhance their operational efficiencies and reduce emissions. However, a systematic analysis of the life cycle impacts of SOFC integration in natural gas operations is necessary to quantitatively and comparatively understand the potential benefits. This study presents a systematic cradle-to-grave life cycle assessment (LCA) based on the ISO 14040 and 14044 standards using a planar anode-supported SOFC with a lifespan of ten years and a functional unit of one MW electricity output. The analysis primarily focused on global warming, acidification, eutrophication, and ozone potentials in addition to human health particulate matter and human tox... [more]

Carbon capture and storage is considered an effective mitigation strategy to reduce the most challenging emissions from heavy industries and gas processing. The safe transport of carbon dioxide via pipelines is an important aspect for developing large-scale Carbon Capture and Storage projects. Dispersion modeling for heavy gas such as carbon dioxide is considerably different from natural gas. The set up for modeling simulations is more challenging than conventional natural gas pipeline for several reasons, such as the differences in thermodynamics that must be considered. Moreover, when the carbon dioxide is transported in dense or liquid phase, the rapid phase changing, and possible consequent formation of solids should be considered. Finally, the equation of state required for accurate prediction of parameters is generally different than the ones applicable for natural gas. The main scope of this comprehensive review is to identify the most important parameters, critical events, suit... [more]

The urgent energy transition needs a better penetration of renewable energy in the world’s energy mix. The intermittency of renewables requires the use of longer-term storage. The present system uses water displacement, in a lined rock cavern or in an aerial pressurised vessel, as the virtual piston of compressor and expander functions in a carbon dioxide heat pump cycle (HPC) and in an organic transcritical cycle (OTC). Within an impermeable membrane, carbon dioxide is compressed and expanded by filling and emptying pumped-hydro water. Carbon dioxide exchanges heat with two atmospheric thermal storage pits. The hot fluid and ice pits are charged by the HPC when renewable energy becomes available and discharged by the OTC when electricity is needed. A numerical model was built to replicate the system’s losses and to calculate its round-trip efficiency (RTE). A subsequent parametric study highlights key parameters for sizing and optimisation. With an expected RTE of around 70%, this CO2... [more]

For reliability and safety issues of injection wells, corrosion resistance of materials used needs to be determined. Herein, representative low-cost materials, including carbon steel X70/1.8977 and low alloyed steel 1.7225, were embedded in mortar to mimic the realistic casing-mortar interface. Two types of cement were investigated: (1) Dyckerhoff Variodur commercial Portland cement, representing a highly acidic resistant cement and (2) Wollastonite, which can react with CO2 and become stable under a CO2 stream due to the carbonation process. Exposure tests were performed under 10 MPa and at 333 K in artificial aquifer fluid for up to 20 weeks, revealing crevice corrosion and uniform corrosion instead of expected pitting corrosion. To clarify the role of cement, simulated pore water was made by dispersing cement powder in aquifer fluid and used as a solution to expose steels. Surface analysis, accompanied by element mapping on exposed specimens and their cross-sections, was carried out... [more]

This study aims to provide a thermodynamic comparison between supercritical CO2 cycles and ORC cycles utilizing flue gases as waste heat source. Moreover, the possibility of using CO2 mixtures as working fluids in transcritical cycles to enhance the performance of the thermodynamic cycle is explored. ORCs operating with pure working fluids show higher cyclic thermal and total efficiencies compared to supercritical CO2 cycles; thus, they represent a better option for high-temperature waste heat recovery provided that the thermal stability at a higher temperature has been assessed. Based on the improved global thermodynamic performance and good thermal stability of R134a, CO2-R134a is investigated as an illustrative, promising working fluid mixture for transcritical power cycles. The results show that a total efficiency of 0.1476 is obtained for the CO2-R134a mixture (0.3 mole fraction of R134a) at a maximum cycle pressure of 200 bars, which is 15.86% higher than the supercritical carbon... [more]

Clathrate formation and guest behaviors in hydroquinone (HQ) clathrates were investigated for the first time using ternary (CO + CO2 + H2) gas mixtures. Two gas compositions (low and high CO2 concentrations) were used to simulate synthesis gases generated from various sources. After reaction at 2.0, 4.0, and 6.0 MPa, the conversion yield of pure HQ to the clathrate form reached >90% if the CO2 partial pressure was 0.7 MPa or higher. In addition, CO2 was the most abundant occupant, whereas CO was only detectable at higher CO concentrations and experimental pressures. The separation efficiency values expressed as molar ratios of CO2 to CO in the solid clathrate form were found to be 12.7 and 23.9 MPa at 4.0 and 6.0 MPa, respectively. The experimental and the calculated results in this study provide information useful for the design of a clathrate-based separation process for synthesis gases from various sources (i.e., synthesis gases with various compositions).

The European Union (EU) energy policy for sustainable development has been the topic of continuous debate, research, and analysis, which frequently focused on objectives and the evaluation of quantitative and qualitative performance. Different approaches can be used for the assessment of sustainable development goals. The authors of the article conducted a literature review of relevant research papers dated 2016−2020. The most common are quantitative methods based on hard data. Some qualitative studies based on soft data are also available but rare. This article proposes hybrid Rough Set Data Envelopment Analysis (DEA) and Rough Set Network DEA models that integrate both approaches. Also, the models allow the inclusion of uncertainty in the underlying data. The article uses hard data of the International Energy Agency (IEA) and the results of the EU survey regarding the influence of the socio-economic environment on CO2 emissions in EU countries. The authors demonstrate that multifacet... [more]

In the last century, the refrigerant R744 (carbon dioxide) has become an environmentally friendly solution in commercial refrigeration despite its particular issues related to the low critical temperature. The use of transcritical cycles in warm and hot countries reveals the necessity of adopting different configurations and technologies to improve this specific cycle. Among these, subcooling methods are well-known techniques to enhance the cooling capacity and the Coefficient of Performance (COP) of the cycle. In this work, an R600a dedicated mechanical subcooling system has been experimentally tested in an R744 transcritical system at different operating conditions. The results have been compared with those obtained using a suction-to-liquid heat exchanger (IHX) to determine the degree of improvement of the mechanical subcooling system. Using the experimental tests, a computational model has been developed and validated to predict the optimal subcooling degree and the cubic capacity... [more]

Adopting a new paradigm for social development implies a transition to a circular economy. The above requires the reduction of greenhouse gas emissions, the utilization of wastes, and the use of renewable energy sources. The most promising way is the use of methanol for industrial and transport applications. China is experiencing a boom in methanol production and its use in almost every sector of the economy. The purpose of this study was to reveal economic benefits, carbon dioxide emissions and the potential production of green methanol. Fuel price history, energy costs and fuel economy were used for economic assessment. Life cycle analysis to evaluate carbon dioxide emissions was applied. It was revealed that only the use of green methanol as a fuel results in decreases in well-to-wheel CO2 emissions compared to fossil fuels. The potential methanol production by using recycled waste and wind power was determined. Its annual production can range from 6.83 to 32.43 million tones. On th... [more]

Up to now, many kinds of deep eutectic solvents (DESs) were investigated for the capture of acidic gases from flue gases. In this review, non-functionalized and functionalized DESs, including binary and ternary DESs, for SO2, CO2 and NO capture, are summarized based on the mechanism of absorption, physical interaction or chemical reaction. New strategies for improving the absorption capacity are introduced in this review. For example, a third component can be introduced to form a ternary DES to suppress the increase in viscosity and improve the CO2 absorption capacity. DESs, synthesized with halogen salt hydrogen bond acceptors (HBAs) and functionalized hydrogen bond donors (HBDs), can be used for the absorption of SO2 and NO with high absorption capacities and low viscosities after absorption, due to physicochemical interaction between gases and DESs. Emphasis is given to introducing the absorption capacities of acidic gases in these DESs, the mechanism of the absorption, and the ways... [more]

Underground geological energy and CO2 storage contribute to mitigation of anthropogenic greenhouse-gas emissions and climate change effects. The present study aims to present specific underground energy and CO2 storage sites in Greece. Thermal capacity calculations from twenty-two studied aquifers (4 × 10−4−25 × 10−3 MJ) indicate that those of Mesohellenic Trough (Northwest Greece), Western Thessaloniki basin and Botsara flysch (Northwestern Greece) exhibit the best performance. Heat capacity was investigated in fourteen aquifers (throughout North and South Greece) and three abandoned mines of Central Greece. Results indicate that aquifers present higher average total heat energy values (up to ~6.05 × 106 MWh(th)), whereas abandoned mines present significantly higher average area heat energy contents (up to ~5.44 × 106 MWh(th)). Estimations indicate that the Sappes, Serres and Komotini aquifers could cover the space heating energy consumption of East Macedonia-Thrace region. Undergroun... [more]

Microbial electrosynthesis (MES) systems can convert CO2 to acetate and other value-added chemicals using electricity as the reducing power. Several electrochemically active redox mediators can enhance interfacial electron transport between bacteria and the electrode in MES systems. In this study, different redox mediators, such as neutral red (NR), 2-hydroxy-1,4-naphthoquinone (HNQ), and hydroquinone (HQ), were compared to facilitate an MES-based CO2 reduction reaction on the cathode. The mediators, NR and HNQ, improved acetate production from CO2 (165 mM and 161 mM, respectively) compared to the control (without a mediator = 149 mM), whereas HQ showed lower acetate production (115 mM). On the other hand, when mediators were used, the electron and carbon recovery efficiency decreased because of the presence of bioelectrochemical reduction pathways other than acetate production. Cyclic voltammetry of an MES with such mediators revealed CO2 reduction to acetate on the cathode surface. T... [more]

All Carbon Capture and Storage (CCS) projects require the transportation of CO2 from a source to a storage location. Although, a compressor and a large diameter pipeline is the normal method used to achieve this, liquefaction, shipping and pumping is sometimes attractive. Identifying the economic optimum is important for all CCS projects, minimizing energy consumption is also important because it corresponds to a resource efficiency in fossil-fuel based projects. This article describes the development and validation of a model that estimates the energy consumption associate with CO2 transportation using the geographic location of the source and the reservoir to incorporate ambient temperature and bathymetry data. The results of the validation work show an average absolute temperature and pressure error less than 1 °C and 1 bar compared to a reference model. The model has been developed using openly accessible data and is made available in a repository for open research data.

To manage greenhouse gas emissions, directives on renewable energy usage have been developed by the European Commission with the objective to reduce overall emissions by 40% by 2030 which presents a significant potential for renewable energy sources. At the same time, it is a challenge for these energy technologies which can only be solved by integrated solutions. Carbon capture and storage combined with geothermal energy could serve as a novel approach to reduce CO2 emissions and at the same time facilitate some of the negative impacts associated with fossil fuel-based power plants. This study focuses on the technical and economic feasibility of combining these technologies based on a published model, data and market research. In the European Union, Germany is the most energy intensive country, and it also has an untapped potential for geothermal energy in the northern as well as the western regions. The CO2 plume geothermal system using supercritical carbon dioxide as the working flu... [more]

Photosynthetic biogas upgrading using two-stage systems allows the absorption of carbon dioxide (CO2) in an absorption unit and its subsequent assimilation by microalgae. The production of microalgae requires large amounts of nutrients, thus making scale-up difficult and reducing economic feasibility. The photosynthetic process produces oxygen (O2) (1 mol per mol of CO2 consumed), which can be desorbed into purified biogas. Two-stage systems reduce its impact but do not eliminate it. In this study, we test the use of landfill leachate as a nutrient source and propose a viable and economical strategy for reducing the O2 concentration. First, the liquid/gas (L/G) ratio and flow mode of the absorber were optimized for 20% and 40% CO2 with COMBO medium, then landfill leachate was used as a nutrient source. Finally, the system was inoculated with nitrifying bacteria. Leachate was found to be suitable as a nutrient source and to result in a significant improvement in CO2 absorption, with out... [more]

An air-independent propulsion system containing fuel cells is applied to improve the operational performance of underwater vehicles in an underwater environment. Fuel-reforming efficiently stores and supplies hydrogen required to operate fuel cells. In this study, the applicability of a fuel-reforming system using various fuels for underwater vehicles was analyzed by calculating the fuel and water consumptions, the amount of CO2 generated as a byproduct, and the amount of water required to dissolve the CO2 using aspen HYSYS (Aspen Technology, Inc., Bedford, MA, USA). In addition, the performance of the fuel-reforming system for methanol, which occupies the smallest volume in the system, was researched by analyzing performance indicators such as methanol conversion rate, hydrogen, yield and selectivity, and reforming efficiency under conditions at which pressure, temperature, steam-to-carbon ratio (SCR), and hydrogen separation efficiency vary. The highest reforming efficiency was 77.7−... [more]

AC pre-discharge currents, breakdown, and flashover voltage measurements are reported in a 10 mm needle-plane arrangement in a 4% NovecTM 4710/96% CO2 gas mixture and compared with CO2 for pressures up to 8.8 bar abs. Flashover measurements were performed on different solid dielectrics (Al2O3_filled epoxy resins, PTFE (Polytetrafluoroethylene) and PE (polyethylene)) for different roughness surface finishes. The effect of fixed conducting needles at various positions on electrical strength is reported. A strong nonlinear behaviour as function of gas pressure was observed for all the studied parameters (gas, needle position, solid insulator, insulator roughness). The non-linear behaviour is attributed to the inception and quenching of glow corona, in the interval between inception and breakdown or flashover voltages. It is found that a 4% concentration of NovecTM 4710 in CO2 has a breakdown/flashover voltage ≈ 1.14 higher than CO2. The glow corona-induced stabilization effect is seen for... [more]

We report an experimental study for the investigation into the suitability of hydrate formation processes for the purification of methane (CH4) from carbon dioxide (CO2) at a sub-cooling temperature of 6 K and a pressure of 4 MPa. The experiments were conducted in a stirred batch reactor. Three different initial CH4/CO2 mixtures with methane fractions of 70.1 mol%, 50.3 mol%, and 28.5 mol% were tested. The separation efficiency was quantified by measuring in situ via Raman spectroscopy the ratios of CH4/CO2 in the gas mixture, the liquid water-rich phase before hydrate formation, and the solid hydrate phase after the onset of the hydrate formation. The results indicated that the main separation effect is obtained due to the preferential dissolution of CO2 into the liquid water-rich phase before the onset of the hydrate formation.

Different alternatives are being studied nowadays in order to enhance the behavior of transcritical CO2 refrigeration plants. Among the most studied options, subcooling is one of the most analyzed methods in the last years, increasing cooling capacity and Coefficient Of Performance (COP), especially at high hot sink temperatures. A new cycle, called integrated mechanical subcooling cycle, has been developed, as a total-CO2 solution, to provide the subcooling in CO2 transcritical refrigeration cycles. It corresponds to a promising solution from the point of view of energy efficiency. The purpose of this work is to present, for the first time, thermodynamic analysis of a CO2 refrigeration cycle with integrated mechanical subcooling cycle from first and second law approaches. Using simplified models of the components, the optimum operating conditions, optimum gas-cooler pressure, and subcooling degree are determined in order to obtain the maximum COP. The main energy parameters of the sys... [more]

Microalgae are a potential means of recycling CO2 from industrial point sources. With this in mind, a novel photobioreactor (PBR) was designed and deployed at a coal-fired power plant. To ascertain the feasibility of using waste heat from the power plant to heat algae cultures during cold periods, two heat transfer models were constructed to quantify PBR cooling times. The first, which was based on tabulated data, material properties and the physical orientation of the PBR tubes, yielded a range of heat transfer coefficients of 19−64 W m−2 K−1 for the PBR at wind speeds of 1−10 m s−1. The second model was based on data collected from the PBR and gave an overall heat transfer coefficient of 24.8 W m−2 K−1. Energy penalties associated with waste heat utilization were found to incur an 18%−103% increase in energy consumption, resulting in a 22%−70% reduction in CO2 capture for the scenarios considered. A techno-economic analysis showed that the cost of heat integration equipment increased... [more]

A centrifugal carbon dioxide compressor is a kind of general machine with extensive applications. The geometry of the side chambers of the compressors can be determined by studying the rotor-stator cavity with centripetal through-flow. In this paper, numerical simulations were conducted to predict the characteristics of flow and heat transfer. Three different speeds of rotation and two axial gap widths were considered. The correlations of the core swirl ratios were determined by fitting the results for two axial gap widths. The amounts of the moment coefficients of the disk were predicted. In order to better analyze the temperature field, the radial distributions of the local heat transfer coefficient were numerically investigated. According to the simulation results, the average Nusselt number was found to be dominated by the turbulent flow parameter. It also seemed to be proportional to the moment coefficient at a fixed circumferential Reynolds number.

Global warming and climate change caused by greenhouse gas (GHG) emissions have rapidly increased the occurrence of abnormal climate events, and both the scale and frequency of geotechnical engineering hazards (GEHs) accordingly. In response, geotechnical engineers have a responsibility to provide countermeasures to mitigate GEHs through various ground improvement techniques. Thus, this study provides a comprehensive review of the possible correlation between GHG emissions and GEHs using statistical data, a review of ground improvement methods that have been studied to reduce the carbon footprint of geotechnical engineering, and a discussion of the direction in which geotechnical engineering should proceed in the future.

Passenger cars account for the largest share of GHG emissions in the road sector. However, given that the number of heavy-duty vehicles registered is lower but accounts for about a quarter of GHG emissions in the road sector, it is necessary to reduce carbon dioxide (CO2) emissions by improving the fuel efficiency of heavy-duty vehicles. However, experiments using dynamometers during the vehicle development process consume a lot of time and cost. Conversely, simulations can quantitatively analyze the sensitivity of parameters and accelerate optimization. Therefore, in this study, we modeled a heavy-duty vehicle using an AVL Cruise simulation and analyzed the effects of payload, air drag coefficient, and rolling resistance on fuel economy, CO2 emission, and the valid window ratio among the moving average window (MAW) for three driving routes. When the average vehicle speed was higher, the effect of the air drag coefficient on fuel economy was high. Additionally, when the average vehicle... [more]

Worldwide, the known recoverable heavy oil and bitumen reserves make up more than 64% of the total reserves, of which more than 60% are trapped in carbonates. Air injection has immense potential for hydrocarbon recovery from various reservoirs. While most of the successful air-based techniques are performed within carbonate reservoirs containing light oil, theoretically, in situ combustion (ISC) has also shown great potential for recovering heavy oil and bitumen. Carbonates are complex in terms of geology and are often associated with fractures and vugs that affect the fluid flow, pressure propagation and progression of the ISC reactions. This paper describes the first experiment in which the triple-porosity concept was applied to simulate heterogeneity through artificially induced vugs, core matrix and fractures. This approach was used to study the feasibility of the ISC recovery technique for heavy oil (14° API) within a dolomite reservoir using a combustion tube (CT) in an experimen... [more]

Fiscal policy is an essential tool that policymakers use for guiding the economy. Thus, the effects of fiscal policy may affect many aspects of our lives, including the impact of carbon dioxide (CO2) emissions. This article investigates the role of fiscal policy, in addition to gross domestic product (GDP), innovation, and financial development, in mitigating CO2 emissions in the context of the Environmental Kuznets Curve theory in the Group of Twenty (G20) countries from 1995 to 2019. The study implied the autoregressive distributed lag of pooled mean group (ARDL-PMG) approach to analyze the suggested model. The results revealed the validity of the model for the G20 countries, as well as a long-run cointegration between the study variables. The results also showed that fiscal policy is associated positively with CO2 emissions. Hence, we recommend reconsidering the applied financial policy, redirecting it to support clean energy projects, provide incentives for projects combating envir... [more]