It is broadly acknowledged that there is an urgent need to reduce carbon-based mobility systems and increase renewable energy alternatives. The automotive industry is one of the greatest consumers of energy in the world. It is fronted with many challenges that aim at reducing carbon emissions. Renewable energy costs are getting cheaper and more cost effective. However, well devised design and control strategies are also needed in order to optimize any systems that are adopted in this field. Previous research shows that the energy consumption for non-traction purposes may be of the same scale as the energy used to move rolling stock, and in some cases even larger. The Kingdom of Saudi Arabia is very interested in the implementation of policies that aim at reducing energy consumption and encouraging renewable energy programs. Under its Vision 2030 development program, the Kingdom of Saudi Arabia is looking to produce 30% of its energy from renewables and other sources, with solar energy... [more]

Domestic hot water preparation is one of the main sources of energy consumption in households. One of the most important elements of domestic hot water (DHW) preparation installation is the storage tank. Its design can significantly affect the efficiency of the system and energy consumption for hot water preparation. This paper presents the results of an experimental study to examine seven different designs of the cold water inlet to the storage tank and the use of two types of obstacles inside this tank placed at three different heights. The number of stratification and the energy efficiency of the system for each variant were examined. Additionally, tests were carried out for different profiles of hot water consumption in order to examine the temperature changes in the DHW tank. A system with an inlet, as an elbow facing down with a single plate, turned out to be the most advantageous variant (3−8% increase in energy efficiency compared to the basic inlet variant). An analogous analy... [more]

This paper focuses on the issue of energy efficiency management in the region of Prešov self-governing region (PSR), Slovakia, as the energy market is liberalized and the behavior of electricity consumers is influenced not only by conventional but also by alternative suppliers of this type of energy. Based on the statistical evaluation of a questionnaire survey focused on the emotional, behavioral, and cognitive behavior of consumers, a model of optimization of system processes of energy efficiency management at the regional level is presented. A one-way ANOVA and t-test were used to determine statistically significant differences, and Pearson’s correlation coefficient was used to determine a statistically significant relationship. Based on the obtained results, a suitable candidate for efficient electricity management is an employee aged 36 to 50 with a technical focus. The proposed model of optimizing the processes of energy management efficiency at the regional level can also be app... [more]

In this study, biological exhaust air treatment was combined with a recuperative heat exchanger in one process stage. The aim of this plant development and testing is not only to reduce ammonia from the exhaust air of pig houses but also to recover thermal energy at the same time. This is intended to offset the high operating costs of exhaust air treatment with savings of heating costs in cold seasons and to use the plant more efficiently. This system was tested for the first time under practical conditions in a pig fattening house in southern Germany. Three different assembly situations of the heat exchanger were examined for 13 days each and then compared with each other. The heating performance of the plant is primarily dependent on the outside air temperature and secondarily on the scrubbing water temperature. Depending on the assembly situation of the heat exchanger, an average heating performance of between 6.0 and 10.0 kW was observed; the amount of recovered thermal energy was... [more]

The housing sector is one of the largest energy consumers in the world. There is an urgent need to renovate the housing stock of existing buildings. Therefore, it is necessary to correctly calculate the energy savings that can be obtained in a renovation project. The correct collection of energy data, the main variables that affect consumption, and people’s usage habits are fundamental elements to quantify the success or consequences that occur in an energy efficiency project. This research study quantifies the results of the energy savings of the European project DREEAM (District Scale Renovation for Energy Efficiency and Market Uptake). This article aims to facilitate the calculation of energy savings with mathematical linear regression models in two different climatic zones in Europe. Furthermore, it aims to improve the calculation of energy savings with mathematical models based on energy data and variables that affect consumption before and after renovations. The variables used fo... [more]

The Energy Performance of Buildings Directive 2018/844/EU introduced the smart readiness indicator (SRI) to provide a framework to evaluate and promote building smartness in Europe. In order to establish a methodological framework for the SRI calculation, two technical studies were launched, at the end of which a consolidated methodology to calculate the SRI of a building basing on a flexible and modular multicriteria assessment has been proposed. In this paper the authors applied the above-mentioned methodology to estimate the SRI of the Italian residential building stock in different scenarios. To this end, eight “smart building typologies”, representative of the Italian residential building stock, have been identified. For each smart building typology, the SRI was calculated in three scenarios: (a) base scenario (building stock as it is); (b) an “energy scenario” (simple energy retrofit) and (c) a “smart energy scenario” (energy retrofit from a smart perspective). It was therefore p... [more]

This paper puts forward a methodology for calculating the duration and energy efficiency of regimes for autoclave steaming of wooden prisms for veneer production at limited heat power of the steam generator, depending on the dimensions of the prism’s cross section, wood moisture content, and loading level of the autoclave. The methodology is based on the use of two personal mathematical models: the 2D non-linear model of the temperature distribution in non-frozen wooden prisms subjected to steaming and subsequent conditioning in an air medium, and the model of the non-stationary heat balance of autoclaves for steaming wood materials. Using the suggested methodology, the calculation and research into the duration and energy efficiency of regimes for heating of beech prisms have been carried out. The variables used were an initial temperature of 0 °C, cross-section dimensions 0.3 × 0.3 m, 0.4 × 0.4 m, and 0.5 × 0.5 m, moisture content of 0.4, 0.6, and 0.8 kg·kg−1, during their steaming i... [more]

Increased pressure is being applied to industrial wastewater treatment facilities to adhere to more stringent regulations for the discharge of treated wastewater and to improve energy efficiency of the process. Nitrogen and phosphorous removal can be challenging to achieve efficiently, and in the case of phosphorous removal, can often necessitate the use of chemicals. There is a major drive globally to improve wastewater treatment infrastructure, whilst simultaneously reducing the carbon footprint of the process. The intermittently aerated sequencing batch reactor offers a modification of the well-known sequencing batch reactor process that can enable lower energy requirements than conventional sequencing batch reactor processes and can facilitate enhanced nutrient removal capacities. However, to date much of the previous literature has focused on relatively short laboratory-scale trials (often with synthetic wastewater) which may not be representative of larger scale system performanc... [more]

Increasing peak power demand implies the increasing significance of energy storage. Technologies that efficiently store heat and cold are also important for increasing the share of renewables and improving the efficiency of heating, ventilation, and air conditioning (HVAC) systems. The present experimental study investigated the dynamic behavior of a room with suspended thermally activated ceiling panels filled with a material containing 60% paraffin. The purpose of the study was to determine the specific cooling power and the total energy supplied to the phase change material (PCM) during regeneration. Convective heat flux density, radiant heat flux density, and the heat transfer coefficient (convective, radiant) at the ceiling surface were calculated. Analysis shows that shifting system activation to use lower temperatures during the night maintains thermal comfort.

Under the Belt and Road concepts of mutual benefit and win−win cooperation, China is strengthening its energy cooperation with other countries. We used several econometric models and social network analysis models to study the impacts of China’s outward foreign direct investment (OFDI) on the host and home countries. We first examined China’s OFDI location preference and analysed the effects of OFDI on energy consumption in host countries. Meanwhile, we observed the impact of the reverse spillover effect of OFDI on China’s energy efficiency. The results indicate that (1) the impact of China’s OFDI on energy consumption in host countries has been lower than that on neighbouring countries, and increased significantly after 2014. (2) The space network of energy consumption in Belt and Road countries has a strict hierarchical structure. However, it was disbanded by the Belt and Road policy in 2014. The network centres are situated primarily in Middle Eastern and European countries, and the... [more]

Empowered by the emergence of novel information and communication technologies (ICTs) such as sensors and high-performance digital communication systems, Europe has adapted its electricity distribution network into a modern infrastructure known as a smart grid (SG). The benefits of this new infrastructure include precise and real-time capacity for measuring and monitoring the different energy-relevant parameters on the various points of the grid and for the remote operation and optimization of distribution. Furthermore, a new user profile is derived from this novel infrastructure, known as a prosumer (a user that can produce and consume energy to/from the grid), who can benefit from the features derived from applying advanced analytics and semantic technologies in the rich amount of big data generated by the different subsystems. However, this novel, highly interconnected infrastructure also presents some significant drawbacks, like those related to information security (IS). We provid... [more]

In a planet with limited resources, climate change is a severe problem, intensified by industrial development. This is particularly important in the construction sector. According to the International Energy Agency (2021), the construction sector is responsible for 40% of the global energy consumption and 36% of CO2 emissions. In this way, sustainable architectural solutions should be a priority in our fight against climate change, for it is necessary to propose solutions that help to reuse existing resources, thus reducing consumption. In this sense, the rehabilitation of buildings with solutions that favor the circular economy will become a key element in the construction sector. This work provides the design of a facade for building rehabilitation based on the circular economy paradigm, which is implanted in a model building as a case study. The HULC tool quantifies the improvement in energy efficiency that this rehabilitation entails when compared to a conventional facade. With the... [more]

In our research, we analyzed the energy and water consumption in diamond mining and laboratory synthesis operations. We used publicly available reports issued by two market leaders, DeBeers and ALROSA, to estimate water and energy use per carat of a rough diamond. The efficiency of the two most popular synthesis technologies for artificial diamonds—High-Pressure-High-Temperature (HPHT) and Microwave-assisted Chemical Vapor Deposition (M-CVD)—was examined. We found that the modern HPHT presses, with open cooling circuits, consume about 36 kWh/ct when producing gem-quality and average-sized (near-) colorless diamonds. ALROSA and DeBeers use about 96 kWh/ct and 150 kWh/ct, respectively, including all energy required to mine. Energy consumption of M-CVD processes can be different and depends on technological conditions. Our M-CVD machine is the least energy-efficient, requiring about 215 kWh/ct in the single-crystal regime, using 2.45-GHz magnetron for the support synthesis. The M-CVD meth... [more]

A daylighting control system that uses the closed loop proportional algorithm needs to be calibrated both during nighttime and daytime. The selection of the daytime calibration time can affect the behavior of the system and is usually performed when the ratio of the illuminance of the ceiling sensor (SD) to the illuminance at a point on the working plane (ED) is relatively large without sunlight patches in the ceiling photo-sensor’s field of view (FOV). However, this requirement is not associated with a specific value and can be achieved under a wide range of conditions related to the sky luminance distribution. In the present work, four ceiling sensors with different field of views (FOVs) were examined in a typical north-facing office space. The effect of daytime calibration on the system’s performance was estimated through the calculation of lighting energy savings and the overdimming percentage. The results show that the effect of both the FOV of the ceiling sensor and the daytime c... [more]

The aim of the study is to explore the intellectual structure of the field and fronts in research on energy efficiency in the context of cloud computing and thus to contribute to science mapping of the research field. The research process was driven by the following study questions: (1) what are the most influential publications in the research field? and (2) what are the research fronts in the research field? The method of direct citation analysis was employed in the research process. Data for analysis were obtained from the Scopus database and analyzed with the use of VOSviewer science mapping software. In response to the first question, we identified the most influential publications in the research field and analyzed their types (i.e., whether they are original research papers or rather the “context” papers e.g., survey or review papers, framework papers, challenges papers, and study papers). Moreover, a comparison analysis between the types of papers among the most cited “classica... [more]

Energy efficiency (EE) is of great concern in cognitive radio networks since the throughput and energy consumption of secondary users (SUs) vary with the sensing time. However, the conditions of the detection probability and false alarm probability should be respected to better protect primary users (PUs) and to improve the sensing performance of SUs. Additionally, the PUs’ minimum averaged power provision should also be regarded as a key problem of interactive linking to SUs. Therefore, an integrated design between the PU and SUs is desired for the coordination of the whole cognitive radio system, especially regarding the satisfaction of EE and performance metrics. This study formulates sensing constraints in a unified way and calculates the minimum SNR of SUs, based on which the essential PU power provision is computed. Furthermore, EE is proved as a decreasing function with the PU’s active ratio, where the maximum EE is obtained corresponding to the minimum QoS requirements of the s... [more]

Passivhaus EnerPHit is a rigorous retrofit energy standard for buildings, based on high thermal insulation and airtightness levels, which aims to significantly reduce building energy consumption during operation. However, extra retrofit materials are required to achieve this standard, which raises a contradiction between how to balance the environmental impacts of the retrofitting material inputs and extremely low energy consumption after retrofit. This motivated the analysis in this paper, which aimed to evaluate the possibilities of reducing the required retrofitting material inputs when trying to achieve the EnerPHit energy standard using a typical suburban dwelling in China’s hot summer−cold winter climate region as a case study. Firstly, how the insulation performance of each envelope component affected the building’s energy consumption was analysed. Based on this, sensitivity simulations of combinations of different insulation levels with different fabric components were investig... [more]

The definition of multiple slicing types in 5G has created a wide field for service innovation in communications. However, the advantages that network slicing has to offer remain to be fully exploited by today’s applications and users. An important area that can potentially benefit from 5G slicing is emergency communications for First Responders. The latter consists of heterogeneous teams, imposing different requirements on the connectivity network. In this paper, the RESPOND-A platform is presented, which provides First Responders with network-enabled tools on top of 5G on-scene planning, with enhanced service slicing capabilities tailored to emergency communications. Furthermore, a mapping of emergency services and communications to specific slice types is proposed to identify the current challenges in the field. Additionally, the proposed tentative mechanism is evaluated in terms of energy efficiency. Finally, the approach is summarized by discussing future steps in the convergence... [more]

Energy is crucial to economic development, but its production usually has a negative impact on the environment. This ambivalence leads to the need for methods to improve energy efficiency. Transportation is one of the largest global energy consumers. Therefore, improving the energy efficiency of transportation is crucial for sustainable development. The aim of this article is to show the limitations of energy management in railways, resulting from the model of market regulation. The question in this context is whether only technological methods can be used in railways to steer its energy efficiency, as is suggested by the existing research. Critical analysis, desk research and a case study of Polish railway undertaking were used to find an answer to the research question. The discussion of the results shows that the European regulatory system leads to greater complications in the field of energy management than in other global regions, where railways are also important for the economy.... [more]

The European Union has set an ambitious goal to tackle climate change, and energy efficiency in the residential sector is among the measures required to close the gap between targeted and actual greenhouse gas emissions. While different policy tools have been applied, the diffusion rate of these measures remains low. A system dynamics simulation model of the residential sector was developed to assess the advantages and drawbacks of energy efficiency policy in the multi-family building sector based on experience accumulated over the last twelve years in Latvia. The model was validated in expert group model building sessions and with historical trends. Simulating the model, a hypothesis was tested that supported the idea that seemingly positive policy tools set the stage for a series of unintended adverse effects due to the complex interactions between different system components. The common assumption that information and financial support should result in significant energy efficiency... [more]

District heating (DH) is an alternative technology to Individual Heating (IH) for satisfying end-user’s needs. This paper assesses the competitiveness of a DH network in the center of Italy from energy, environmental, and economic points of view considering both thermal power plant and end-users’ sides. On the thermal power plant side, the energy analysis considers the Primary Energy Saving (PES) and the specific energy (Esp) of the fuel actually exploited in the thermal power plant compared to its Low Heating Value (LHV), while the environmental analysis considers the avoided CO2 and the economic analysis considers the Energy Efficiency Certificates (EECs). Results showed that the current thermal power plant configuration with two boilers and a Combined Heat and Power (CHP) unit reaches a yearly PES of 21.3% as well as 1099 tCO2 avoided. From the economic analysis of the thermal power plant side, 829 EECs with an economic return of 207,222€ are obtained, while from the end-users’ side... [more]

The 2030 Climate target plan of the European Commission (EC) establishes a greenhouse gases (GHG) emissions reduction target of at least 55% by 2030, compared to 1990. It highlights that all transport modes—road, rail, aviation and waterborne—will have to contribute to this aim. A smart combination of vehicle/vessel/aircraft efficiency improvements, as well as fuel mix changes, are among the measures that can reduce GHG emissions, reducing at the same time noise pollution and improving air quality. This research provides a comprehensive analysis of recent research and innovation in low-emission alternative energy for transport (excluding hydrogen) in selected European Union (EU)-funded projects. It considers the latest developments in the field, identifying relevant researched technologies by fuel type and their development phase. The results show that liquefied natural gas (LNG) refueling stations, followed by biofuels for road transport and alternative aviation fuels, are among the r... [more]

This study analyses the Ukrainian energy system in the context of the Paris Agreement and the need for the world to limit global warming to 1.5 °C. Despite ~84% of greenhouse gas emissions in Ukraine being energy- and process-related, there is very limited academic literature analysing long-term development of the Ukrainian energy system. This study utilises the TIMES-Ukraine model of the whole Ukrainian energy system to address this knowledge gap and to analyse how the energy system may develop until 2050, taking into current and future policies. The results show the development of the Ukrainian energy system based on energy efficiency improvements, electrification and renewable energy. The share of renewables in electricity production is predicted to reach between 45% and 57% in 2050 in the main scenarios with moderate emission reduction ambitions and ~80% in the ambitious alternative scenarios. The cost-optimal solution includes reduction of space heating demand in buildings by 20%... [more]

Transport is one of the key sectors of the European economy. However, the intensive development of transport caused negative effects in the form of an increase in the emission of harmful substances. The particularly dramatic situation took place in the V4 countries. This made it necessary to implement solutions reducing emissions in transport, including passenger transport. Such activities can be implemented in the field of implementation of low-emission and zero-emission vehicles for use. That is why the European Union and the governments of the Visegrad Group countries have developed numerous recommendations, communications, laws, and strategies that order carriers to implement low- and zero-emission mobility. Therefore, transport organizers and communication operators faced the choice of the type of buses. From an economic point of view, each entrepreneur is guided by the economic efficiency of the vehicles used. Hence, the main aim of the article was to conduct an economic evaluati... [more]

Data centres are a key infrastructure for the global digital economy, helping enable the EU “Digital Decade” by 2030. In 2015, data centres were estimated to consume 2.5% of EU electricity demand. In Ireland, the concentrated presence of data centres could consume 37% of national electricity demand by 2028. The uncertainty of data centre facility-level energy efficiency paired with the need to achieve a low-carbon economy pose significant challenge for generation and transmission network planning. This is the first paper to apply a model of technology diffusion with a national forecast of changes in Irish data centre electricity demand through more efficient liquid cooling. The methodology serves as a technology-agnostic resource for practitioners performing forecasts under uncertainty with limited information. Results suggest that technology adoption could lower national electricity demand by 0.81% if adopted by new plant from 2019 to 2028. Savings rise to 3.16% over the same period i... [more]