This study aimed to compare the performance and economic efficiency of greenhouse solar and hot air drying. These are widely used and inexpensive techniques for preserved fruit production in Thailand. Two drying methods were used to dry mango fruit, var. Nam Dok Mai. During the process of both drying methods, the moisture content of mango slices was reduced from an average 85.6% to 12.5% wet basis. To determine the most profitable dryer system for investment, economic analyses of greenhouse solar and hot air drying, involving the main variables affecting their profitability, were investigated, including production and maintenance cost, capital costs, revenue, and drying capacities. The internal rate of return (IRR), net present value (NPV), benefit to cost ratio (BCR) and payback period (PBP) were all evaluated. The results of economic evaluation revealed that high values of IRR, NPV, and BCR, and low value of PBP made the two drying systems cost efficient. However, when the incrementa... [more]

Modeling phase change materials (PCMs) has been a topic of research interest in the past, carried out experimentally and by means of computational fluid dynamics (CFD). The implemented solidification and melting (SM) model in Ansys Fluent-based on the enthalpy-porosity formulation is widely used in the literature. To the authors’ knowledge, few publications apply the apparent heat capacity (AHC) method in Ansys Fluent and even fewer have discussed both. The SM approach applies a linear relationship of the liquid fraction between solidus and liquidus temperature although it is known that the phase transition follows a non-linear behavior, which can be captured using the AHC method as a curve shape and location of the specific heat capacity containing information about the nature of phase transition behavior. Important factors in modeling are the temperature dependent thermophysical material properties density, viscosity, and thermal conductivity. They are often considered constant in th... [more]

This work is concerned with the incorporation of semi-mechanistic residence time metrics into population balance equations for twin screw granulation processes to predict key properties. From the historical residence time and particle size data sourced, process parameters and equipment configuration information were fed into the system of equations where the input flow rates and model compartmentalization varied upon the parameters. Semi-mechanistic relations for the residence time metrics were employed to predict the particle velocities and dispersion coefficients in the axial flow direction of the twin screw granulation. The developed model was then calibrated for several experimental run points in each data-set. The predictions were evaluated quantitatively through the parity plots. The root mean square error (RMSE) was used as a metric to compare the degree of goodness of fit for different data-sets using the developed semi-mechanistic relations. In summary, this paper presents a m... [more]

To study the influence of filling step and advancing distance on the deformation and failure of a working face floor, a mechanical model based on elastic foundation beam theory is established. The deflection and bending moment curves of the floor under different filling steps and advancing distance are obtained by Maple. Then, a fluid−solid coupling model of paste-filling mining on confined water is established by FLAC3D. The effects of different filling steps and advancing distance on the floor displacement, stress, and plastic zone of the floor are analyzed. The results show that there is a “concave” quadratic relationship between the filling step and the maximum displacement of the floor, and there is a “convex” quadratic relationship between the advancing distance and the maximum displacement of the floor. The maximum stress of the floor increases linearly with the increase in filling distance and tends to be stable with the increase in advancing distance. Moreover, the increase in... [more]

This paper proposes an octagonal layout for enhancing the ability of resisting electromagnetic interference in Through Silicon Via (TSV) array. The influential factors of crosstalk noise between TSVs are investigated, including the TSV pitch, signal and ground TSVs location, and signal types (single-end and differential signal) by using a coplanar wave guide (CPW) testing structure. These results, based on traditional TSV arrays, show that a staggered TSV layout with differential signals had lower crosstalk noise. On this basis, the octagonal layout of TSV array is proposed and we show that it has obvious superiority in reducing occupied silicon area and crosstalk noise. Compared with traditional TSV arrays, the crosstalk noise is almost reduced by 44%. In order to further reduce the silicon area occupied by TSV without worsening crosstalk noise, the new division TSV structure is proposed in which a large TSV was substituted by four smaller TSVs. The area occupied by a single TSV and T... [more]

In order to eliminate driving dangers caused by tire surface bubbles, the detection method of bubble defects on tire surfaces based on line lasers and machine vision is studied. Since it is difficult to recognize tire surfaces directly through images, line laser scanning is used to obtain tire images. The filtering method and morphology method are combined to preprocess these images. The gray centroid method is adopted to extract the center of the laser stripe, and then the algorithm to determine the positions of bubble defects on tire surfaces is proposed. According to the geometric characteristics of tire bubbles, the coordinates of starting points, ending points, and rough positions of vertices are determined. Then, the ordinates of the laser center with sub-pixel accuracy near bubble vertices are discretely magnified. The mask made of Gaussian function is convoluted with the magnified region, and the maximum value is obtained. Furthermore, the position of bubble vertices can be acc... [more]

Dimensionless expressions of exergy destruction, normalized to ambient temperature and heat capacity of the weaker stream, for all basic types of recuperators are derived. The analytical expressions for maximum exergy destruction were calculated using the GNU Octave software for all recuperators, namely parallel-flow and counter-flow recuperators, and all forms of cross-flow heat exchangers, namely without mixing of streams, only mixing the streamlines of the weaker stream, only mixing the streamlines of the stronger stream and mixing the weaker and stronger streams. For parallel-flow and counter-flow recuperators, as well as for their special cases, expressions for local and total exergy destruction are given. It is shown that the maximum exergy destruction, as a local extreme, is the same for all recuperators for mutually equal values of the quantities π3 (ratio of the heat capacity of the weaker stream to the heat capacity of the stronger stream) and πT (ratio of the inlet temperatu... [more]

Soil organic carbon (SOC) content is a vital indicator for soil health. The use of moldboard (traditional) plowing for many years had led to a prominent decline in the SOC and soil organic matter (SOM) in Southern Russia. Application of no-tillage (NT) is a sustainable alternative to conventional tillage (CT) as it offers an advantage for SOC store. The aim of the study was to assess soil organic carbon dynamics in response to tillage practices in the steppe zone of Southern Russia. The conservation of SOC under different tillage systems (CT and NT) was evaluated in comparison with the soils of the virgin soils (VS) in three different regions of the steppe zone of the Lower Don region (Southern of the European part of Russia). The SOC content under the conditions of CT was significantly lower than that in the VS and demonstrated an inclining trend when using NT technology. We estimate that the transition to NT over an area of 5.5 million hectares will lead to a significant reduction of... [more]

This article presents the results of the conversion of biomass-based glucose to levulinic acid (LA) with the use of Na-BEA commercial zeolite catalyst. For this purpose, synthetic zeolite BEA was used as a matrix. The glucose conversion process with the participation of Na-BEA zeolite allowed the following acids to be obtained: levulinic acid, lactic acid, pyruvic acid and formic acid. The highest yield of levulinic acid was achieved when processed for 1−5 h at 200−250 °C with 0.1 g and 0.6 g of Na-BEA catalyst. We also compare the one-pot heterogeneous process with similar homogeneous process using H2SO4 as catalyst.

Cytokine oncostatin M (OSM) plays an important role in a variety of inflammatory reactions and is mainly produced in neutrophils in inflammatory diseases. While natural pentacyclic triterpenoid ursolic acid (UA) possesses a wide range of beneficial effects, such as anti-oxidant, anti-tumor, and anti-inflammatory, the regulatory processes of OSM suppression by UA in neutrophils are still poorly understood. This study was aimed at examining how UA regulates OSM expression in neutrophil-like differentiated (d)HL-60 cells. Enzyme-linked immunosorbent assay, quantitative polymerase chain reaction, and immunoblotting were employed to analyze the effects of UA. Whereas stimulation with granulocyte-macrophage colony-stimulating factor (GM-CSF) led to elevations of OSM production and mRNA expression, these elevations were lowered by treatment with UA in neutrophil-like dHL-60 cells. When the cells were exposed to GM-CSF, phosphorylated levels of phosphatidylinositol 3-kinase, Akt, and nuclear f... [more]

With global warming, and internal combustion engine emissions as the main global non-industrial emissions, how to further optimize the power performance and emissions of internal combustion engines (ICEs) has become a top priority. Since the internal combustion engine is a complex nonlinear system, it is often difficult to optimize engine performance from a certain factor of the internal combustion engine, and the various parameters of the internal combustion engine are coupled with each other and affect each other. Moreover, traditional experimental methods including 3D simulation or bench testing are very time consuming or expensive, which largely affects the development of engines and the speed of product updates. Machine learning algorithms are currently receiving a lot of attention in various fields, including the internal combustion engine field. In this study, an artificial neural network (ANN) model was built to predict three types of indicators (power, emissions, and combustio... [more]

The performance of a metal-enhanced fluorescence (MEF) substrate is fundamentally based on the orientation of the metal nanostructures on a solid substrate. In particular, two-dimensional (2D) periodic metallic nanostructures exhibit a strong confinement of the electric field between adjacent nanopatterns due to localized surface plasmon resonance (LSPR), leading to stronger fluorescence intensity enhancement. The use of vertical vibration-assisted convective deposition, a novel, simple, and highly cost-effective technique for preparing the 2D periodic nanostructure of colloidal particles with high uniformity, was therefore proposed in this work. The influences of vertical vibration amplitude and frequency on the structure of thin colloidal film, especially its uniformity, monolayer, and hexagonal close-packed (HCP) arrangement, were also investigated. It was found that the vibration amplitude affected film uniformity, whereas the vibration frequency promoted the colloidal particles to... [more]

This paper focuses on the difficulties that appear when the number of fault samples collected by a permanent magnet synchronous motor is too low and seriously unbalanced compared with the normal data. In order to effectively extract the fault characteristics of the motor and provide the basis for the subsequent fault mechanism and diagnosis method research, a permanent magnet synchronous motor fault feature extraction method based on variational auto-encoder (VAE) and improved generative adversarial network (GAN) is proposed in this paper. The VAE is used to extract fault features, combined with the GAN to extended data samples, and the two-dimensional features are extracted by means of mean and variance for visual analysis to measure the classification effect of the model on the features. Experimental results show that the method has good classification and generation capabilities to effectively extract the fault features of the motor and its accuracy is as high as 98.26%.

This study investigated the effect of gum Arabic and starch-based coating and two polyliners (Liner 1-micro-perforated Xtend® and Liner 2-macro-perforated high-density polyethylene) on whole ‘Wonderful’ pomegranate fruit during cold storage (5 ± 1 °C and 95 ± 2% RH). Uncoated (UC) and coated (GAMS) fruit were packaged into standard open top ventilated cartons (dimensions: 0.40 m long, 0.30 m wide and 0.12 m high) with (GAMS + Liner 1, GAMS + Liner 2, UC + Liner 1 and UC + Liner 2) or without (UC and GAMS) polyliners. After 42 d, treatment GAMS + Liner 1 recorded the least weight loss (4.82%), whilst GAMS recorded lower (8.77%) weight loss than UC + Liner 2 (10.07%). The highest (24.74 mLCO2 kg−1h−1) and lowest (13.14 mLCO2 kg−1h−1) respiration rates were detected in UC and GAMS + Liner 1, respectively. The highest and lowest total soluble solids were recorded for GAMS (16.87 °Brix), and GAMS + Liner 1 (15.60 °Brix) and UC + Liner 1 (15.60 °Brix), respectively. Overall, no decay was det... [more]

Jet velocity is an important parameter affecting the air entrainment rate of plunging liquid jet processes. While the vast majority of researchers have investigated the effect of jet velocity, only a few of them considered the effect of jet length in calculating the jet velocity at impingement point. This study investigates the difference (ΔV) between the jet velocity at the inception of the nozzle (Vj) and the impingement point (VL) for a range of operating conditions. Furthermore, bubble voidage inside the downcomer, another critical parameter in plunging jets, is estimated using three different voidage equations incorporated inside a momentum balance model to predict the two-phase elevation level (HR) inside the downcomer. Results showed that ΔV is significant (VL > Vj), especially at low jet flow rates and high jet lengths. Generally, the momentum balance model predicted the HR well, and its prediction improves with downcomer diameter. Given that, the model still needs to be refine... [more]

In this paper, the influence of hydrodynamic conditions in Kenics static mixer, which acts as a multifunctional reactor, on precipitation kinetics of barium sulfate is investigated. The investigated range of the Reynolds number varied between 500 and 5000, which covered both laminar and turbulent flow regimes. In all experiments, the relative supersaturation was maintained at the constant level (σ = 205). The obtained precipitate was collected and used for crystal size distribution (CSD) determination. On that basis, the kinetic parameters of the process were calculated using the mixed suspension mixed product removal (MSMPR) mathematical model of the process. It was found that for the whole investigated range of Reynolds number, the mixing conditions were satisfactory. CSD analysis showed that in the laminar regime, a clear tendency in crystal behavior could not be noticed. However, during the analysis of the turbulent regime, the presence of a critical Reynolds number was noticed. Ab... [more]

Hydrogen is expected to be a next-generation energy source that does not emit carbon dioxide, but when used as a fuel, the issue is the increase in the amount of NOx that is caused by the increase in flame temperature. In this study, we experimentally investigated NOx emissions rate when hydrogen was burned in a hydrocarbon gas burner, which is used in a wide temperature range. As a result of the experiments, the amount of NOx when burning hydrogen in a nozzle mixed burner was twice as high as when burning city gas. However, by increasing the flow velocity of the combustion air, the amount of NOx could be reduced. In addition, by reducing the number of combustion air nozzles rather than decreasing the diameter of the air nozzles, a larger recirculation flow could be formed into the furnace, and the amount of NOx could be reduced by up to 51%. Furthermore, the amount of exhaust gas recirculation was estimated from the reduction rate of NOx, and the validity was confirmed by the relation... [more]

In order to solve the problem of wax deposition in waxy crude oil from the Daqing oilfield, cold fingers were used in the experimentation. Compared with other methods, the cold finger method is simple, easy to operate, and takes little space. Measurements of wax deposition with temperature, temperature differences between the crude oil and the wall, deposition time, and cold finger rotation rate were made. The results showed that the deposition rate is up to 0.35 g/h at 8−24 h. The maximum deposition rate at 90 rotations/min was 0.26 g/h, which is 3% higher than the minimum deposition rate.

Microbial fuel cells (MFCs) are promising technologies, aiming at treating different types of industrial and domestic wastewater. In recent years, more and more publications focusing on wastewater treatment have been published. Based on the retrieval of publications from Web of Science Core Collection database, the new emerging trends of microbial fuel cells in wastewater treatment was evaluated with a scientometric analysis method from 1995 to 2020. All publications downloaded from (WOS) were screened by inclusion criteria, and 2233 publications were obtained for further analysis. Document co-citation and burst detection of MFCs in wastewater treatment were analyzed and visualized by software of CiteSpace. Our study indicated that “Environmental Science” is the most popular discipline, while the journal of Bioresource Technology published the greatest quantity of articles in the field of MFCs applied wastewater treatment. China and the Chinese Academy of Science are the most productiv... [more]

Innovations in food extrusion technology are enabling its rapid expansion and applicability in diverse areas related to bioprocessing and value addition. This study relates raw material particulate rheology to the granular flow in a single screw food extruder. Raw materials based on corn (i.e., meal, flour, and starch), wheat (i.e., farina, flour, and starch), and sucrose (i.e., granulated, superfine, and powdered) were used as model particulate systems for the study. Various particulate-scale characteristics and flow parameters of these nine materials were determined using a powder rheometer, a promising new offline tool. Properties such as basic flow energy, specific energy, cohesion, stability index, flow function, and effective angle of internal friction were good indicators of flowability in an extruder. Corn meal exhibited lower energy requirements and a higher propensity for flow than corn flour (6.7 mJ/g versus 10.7 mJ/g, and “free-flowing” versus “cohesive,” according to Flow... [more]

Plasma-facing components (PFCs) are used as the barrier to the beam of high heat flux generated due to nuclear fusion. Therefore, efficient cooling of PFCs is required for safety and smooth operation of a fusion reactor. The Hyper Vapotron (HV) is generally used as the heat exchanger to cool down the PFCs during operation. These heat exchangers use pool and flow boiling mechanisms, and hence, their ability is inherently constrained by critical heat flux (CHF). The boiling of nanofluid is very promising as the working fluid in the HV. The efficiency of the HV increases due to the increase in CHF by applying nanofluids. However, the feasibility of nanofluid cooling in fusion reactors needs proper understanding. This paper reviews the recent developments in the utilization of boiling phenomena in nanofluid as a coolant in the HV. Experiments, theoretical studies, significant achievements, and challenges are analyzed and discussed. Finally, important points are indicated for future researc... [more]

The present study deals with the stock-dependent Markovian demand of a retrial queueing system with a single server and multiple server vacation. The items are restocked under a continuous review (s,Q) ordering policy. When there is no item in the system, the server goes on vacation. Further, any arrival demand permits entry into an infinite orbit whenever the server is on vacation. In the Matrix geometric approach with the Neuts-Rao truncation technique, the steady-state joint distribution of the number of customers in orbit, the server status, and the inventory level is obtained. Under the steady-state conditions, some significant system performance measures, including the long-run total cost rate, are derived, and the Laplace-Stieltjes transform is also used to investigate the waiting time distribution. According to various considerations of uncontrollable parameters and costs, the merits of the proposed model, especially the important characteristics of the system with stock depend... [more]

Microalgae (including cyanobacteria) are the basis for an emerging worldwide industry but still face significant bottlenecks in contributing to the global economy. It is an enormous challenge to translate experiences from established industries such as aquaculture and agriculture to the microalgae sector. In particular, this includes the challenge of adapting regulations that apply to such macroscopic production and mindsets, to the microscopic world of microalgae and to the scale-up to a million times smaller. Current European and country-based regulations do not always, indeed rarely, consider relevant specific issues that limit the path for innovation and growth applicable to the microalgae sector. In this work, the boundaries for the main issues impacting this sector are presented and discussed. Examples and possible analytical frameworks are presented in a question and answer format. Relevant key topics and related boundaries are discussed: What are algae and how do microalgae dif... [more]

Matrix acidizing in carbonate reservoirs is a process that has been long used to increase productivity in oil and gas producing formations. The main goal is to create wormholes that bypass the damage in the formation. Hydrochloric acid (HCl) is the main acid used for this; however, it has several disadvantages that affect the success of these treatments. Its high reaction rate, inability to divert, and corrosive nature are a few of the reasons why research in this area has focused on finding alternative fluids. This paper discusses studies on successful alternatives to HCl. It has been observed that emulsified acids, which work with the addition of a surfactant to HCl, have shown positive results as their high viscosity allows them to retard the reaction rate between the acid and the rock and form effective and dominant wormholes. This is needed, especially in high-temperature environments. As HCl also lacks the ability to divert to low-permeability zones in highly heterogeneous format... [more]

This work presents an overview of the modern approaches embracing advanced equipment and validation parameters of both liquid and gas chromatography techniques, including thin-layer chromatography (TLC), column liquid chromatography (CLC), and gas chromatography (GC), suitable for the identification and quantitative determination of various bioactive compounds occurring in pharmaceutical products and medicinal plants in the time from 2020 to 2021 (November). This review confirmed that HPLC is an incredibly universal tool, especially when combined with different detectors, such as UV-Visible spectroscopy, mass spectrometry (MS), and fluorescence detection for numerous active ingredients in different pharmaceutical formulations without interferences from other excipients. TLC, in combination with densitometry, is a very efficient tool for the determination of biologically active substances present in pharmaceutical preparations. In addition, TLC coupled to densitometry and mass spectrome... [more]