The restructuring of power systems and the ever-increasing demand for electricity have given rise to congestion in power networks. The use of distributed generators (DGs) may play a significant role in tackling such issues. DGs may be integrated with electrical power networks to regulate the drift of power in the transmission lines, thereby increasing the power transfer capabilities of lines and improving the overall performance of electrical networks. In this article, an effective method based on the Harris hawks optimization (HHO) algorithm is used to select the optimum capacity, number, and site of solar-based DGs to reduce real power losses and voltage deviation. The proposed HHO has been tested with a complex benchmark function then applied to the IEEE 33 and IEEE 69 bus radial distribution systems. The single and multiple solar-based DGs are optimized for the optimum size and site with a unity power factor. It is observed that the overall performance of the systems is enhanced wh... [more]

Nonlinear control problems in turbofan engines are challenging. No single nonlinear controller can achieve desired control effects in a full flight envelope, but in the case of multiple controllers, there exist problems in the bumpless transfer between different controllers. To this end, this paper presents a bumpless transfer mechanism for an uncertain switched system based on integral sliding mode control (ISMC), and the mechanism can be used for the speed control of turbofan engines. The uncertain switched system is used to describe the turbofan engine dynamics. Then, the ISMC controller is derived for subsystems of the uncertain switched system. A resetting scheme is introduced for the ISMC controller to ensure the continuity of control inputs during the controller transition, as well as the bumpless transfer. In view of the transient behavior caused by controller switching, the global stability of the switched system is analyzed using the multiple Lyapunov function approach and av... [more]

The fuel qualities of several biodiesels containing highly saturated, mono, and poly unsaturated fatty acids, as well as their combustion and exhaust emission characteristics, were studied. Six biodiesel samples were divided into two groups based on their fatty acid composition, including group 1 (coconut, castor, and jatropha) and group II (palm, karanja, and waste cooking oil biodiesel). All fuels (in both groups) were tested in a single-cylinder off-road diesel engine. Castor and karanja biodiesel, both rich in mono-unsaturation level, have a high viscosity of about 14.5 and 5.04 mm2/s, respectively. The coconut and palm biodiesels are rich in saturation level with cetane numbers of 62 and 60, respectively. In both groups, highly saturated and poly-unsaturated methyl esters presented better combustion efficiency and less formation of polluted emissions than mono-unsaturation. At full load, coconut and palm biodiesel displayed 38% and 10% advanced start of combustion, respectively, w... [more]

A microgrid is a set of decentralized loads and electricity sources, mainly renewable. It can operate connected to and synchronized with a traditional wide-area synchronous grid, i.e., a macrogrid, but can also be disconnected to operate in “island mode” or “isolated mode”. When this microgrid is able to manage its own resources and loads through the use of smart meters, smart appliances, control systems, and the like, it is referred to as a smart grid. Therefore, the management and the distribution of the energy inside the microgrid is an important issue, especially when operating in isolated mode. This work presents an overview of the different solutions that have been tested during the last few years to manage microgrids. The review shows the variety of mature and tested solutions for managing microgrids with different configurations and under several approaches.

In the petrochemical industry, multiphase flow, including oil−water two-phase stratified laminar flow, is more common and can be easily obtained through mathematical analysis. However, there is limited mathematical analytical model for the simulation of oil−water flow under turbulent flow. This paper introduces a two-dimensional (2D) numerical simulation method to investigate the pressure gradient, flow field, and oil−water interface height of a pipeline cross-section of horizontal tube in an oil−water stratified smooth flow. Three Reynolds average N−S equation models (k−ε, k−ω, SST k−ω) are involved to simulate oil−water stratified smooth flow according to the finite volume method. The pressure gradient and oil−water interface height can be computed according to the given volume flow rate using the iteration method. The predicted result of oil−water interface height and velocity profile by the model fit well with several published experimental data, except that there is a large error... [more]

The article deals with the problem of the effects of using a wooden church on thermal and humidity conditions forming inside. Religious services in the studied site were provided several times a year. The building was not used in the remaining time. The analysis of the effects of the frequency of religious services and the number of people at the services on the formation of temperature and humidity conditions in the wooden church is provided in this paper. The effect of the presence of people in the church on CO2 concentration fluctuations was also studied. Analysis of the results showed that external conditions have the greatest effect on internal microclimate substitutions. The presence of people affects temporary fluctuations in internal parameters. Both the number of people attending the service and the time of year are important. An indoor air temperature amplitude of 9.4 °C was recorded during the winter period. The CO2 level in the church during the service exceeded the limit v... [more]

Vertical axis turbines, which extract kinetic energy from currents, can produce electricity independently from a current’s direction. Hence, this type of turbines raises interest for harvesting energy from tidal currents, where flow changes direction during flood and ebb tides, and where currents present large variation of direction during tide. Methods for representing vertical axis turbines in tidal farms should be implemented in order to predict correctly power production with an acceptable time cost. The Actuator Cylinder (AC) is one of them. Numerical results in terms of wakes, with the study of velocity profiles, and efforts are compared to experiences, as well as showed that the method is sufficiently accurate and for a reasonable computing time, which is of prime importance for tidal turbines farms studies. The Actuator Cylinder method is implemented in ANSYS Fluent in a 2D stationary resolution. The method is then applied to a double levels of two counter-rotating rotors marin... [more]

This work presents a comparison study of the CFD modeling with two different turbulence modeling approaches viz. unsteady RANS and LES, on a full-scale model of the (New) MEXICO rotor wind turbine. The main emphasis of the paper is on the rotor and wake aerodynamics. Simulations are carried out for the three wind speeds considered in the MEXICO experiment (10, 15, and 24 ms−1). The results of uRANS and LES are compared against the (New) MEXICO experimental measurements of pressure distributions, axial, radial, and azimuth traverse of three velocity components. The near wake characteristics and vorticity are also analyzed. The pressure distribution results show that the LES can predict the onset of flow separation more accurately than uRANS when the turbine operates in the stall condition. The LES can compute the flow structures in wake significantly better than the uRANS for the stall condition of the blade. For the design condition, the mean absolute error in axial and radial velocity... [more]

Decarbonization is an activity aimed at reducing greenhouse gas emissions to limit climate change and global warming. Ensuring macroeconomic stabilization is the basis for ecological action. The question is whether macroeconomic stabilization helps companies, institutions and countries act for decarbonization. This article presents research on the impact of components of macroeconomic stabilization on decarbonization and energy efficiency in the largest greenhouse gas emitters in the European Union from 1990 to 2020. We focus on the following countries, France, Germany, Italy, Poland and Spain. The contribution to knowledge is using the pentagon of macroeconomic stabilization to assess macroeconomic stabilization’s impact on decarbonization and energy efficiency. According to the correlation coefficients, the Ordinary Least Squares and the Seemingly Unrelated Regression method, there is a statistically significant impact of components of macroeconomics stabilization on decarbonization... [more]

In the last few years, several countries have accomplished their determined renewable energy targets to achieve their future energy requirements with the foremost aim to encourage sustainable growth with reduced emissions, mainly through the implementation of wind and solar energy. In the present study, we propose and compare five optimized robust regression machine learning methods, namely, random forest, gradient boosting machine (GBM), k-nearest neighbor (kNN), decision-tree, and extra tree regression, which are applied to improve the forecasting accuracy of short-term wind energy generation in the Turkish wind farms, situated in the west of Turkey, on the basis of a historic data of the wind speed and direction. Polar diagrams are plotted and the impacts of input variables such as the wind speed and direction on the wind energy generation are examined. Scatter curves depicting relationships between the wind speed and the produced turbine power are plotted for all of the methods and... [more]

Photovoltaic (PV) systems are well-known systems that convert solar energy into electrical energy. Increases in operating temperature induce a drop in conversion efficiency and, thus, in the output power produced by the panel. This paper investigates the effectiveness of using Phase Change Materials (PCMs) in cooling PV modules. Due to its high storage density with limited temperature fluctuations, the latent heat storage in a PCM is an important factor. This depends on the thermophysical properties of PCMs such as the melting point, specific heat capacity, latent heat, density, etc. This paper aims to make a comparison between four types of PCM with different melting points and physical properties. Indoor experimental studies were performed using five prototypes. A halogen lamp was used as a solar simulator to ensure that experiments were carried out under the same irradiance. The first prototype was the reference, which consisted of a PV panel, a stand, and an electric circuit withou... [more]

In order to solve the problems of roadway stability and easy instability under repeated mining of close-distance coal seam groups, the mechanism and control technology of surrounding rock instability under repeated mining were studied via indoor testing, field testing, physical similarity simulation experiment, and numerical simulation. The results show that the surrounding rock of roadway has low strength, low bearing capacity, and poor self-stabilization ability, and it is vulnerable to engineering disturbances and fragmentation. Affected by the disturbance under repeated mining, the roadway surrounding rock cracks are developed and the sensitivity is strong, and it is prone to large-scale loose and destroyed. The location of the roadway is unreasonable, and the maximum principal stress of the roadway is 3.1 times of the minimum principal stress, which is quite different. Thus, under a large horizontal stress, the surrounding rock undergoes long-range expansion deformation. On the ba... [more]

This article reviews a method of hydrogen production based on partial non-catalytic oxidation of natural gas in an original synthesis gas generator. The working principles of the unit are similar to those of liquid-propellant rocket engines. This paper presents a description of the operation and technical characteristics of the synthesis gas generator. Its application in the creation of small-scaled plants with a capacity of up to 5−7 thousand m3/h of hydrogen is justified. Hydrogen production in the developed installation requires a two-stage method and includes a technological unit for producing a hydrogen-containing gas. Typical balance compositions of hydrogen-containing gas at the synthesis gas generator’s outlet are given. To increase the hydrogen concentration, it is proposed to carry out a two-stage steam catalytic conversion of carbon monoxide contained in the hydrogen-containing gas at the synthesis gas generator’s outlet using a single Cu−Zn−cement-containing composition. Ba... [more]

This study evaluates temperatures measured at district heating (DH) valves in manholes and their usability for non-destructively assessing the thermal performance of buried DH pipes. The study was conducted as a field test in which part of a DH network was shut down and the temperature decline in the valves was analysed in terms of absolute temperature and thermal response time from the DH pipe to the top of the valve. The calculated and measured supply pipe temperatures by the drainage valves were in good agreement, with 1% deviation. The valve measurement analysis from this study shows that the drainage valve has good potential to serve as a measurement point for assessing the thermal status of a DH network. However, the shutdown valve measurements were greatly affected by the manhole environment.

Smart cities are an extremely important, multi-faceted subject, both in terms of their practical aspects and in terms of research. This is expressed, among other things, in the multitude of approaches to this concept. These approaches differ based on the emphasis placed on individual aspects: some focus more on technology, and others put more weight on social issues, while still others value sustainable development issues. Currently, an important topic of discussion about the development of the smart city—the importance of which has become even greater in the context of the COVID-19 pandemic—is the digital transformation of the city. The use of robotic process automation (RPA) tools can be a part of such a transformation, as such tools, using advanced software, enable the automation of those tasks carried out thus far by humans. Although such an approach has, to date, been widespread in the case of enterprises (in particular, those operating in the financial and BPO/SSC sectors, but le... [more]

Six supplementary cementitious materials (SCMs) were identified to be incorporated in concrete exposed to high-temperature cycling conditions within the thermal energy storage literature. The selected SCMs are bauxite, chamotte, ground granulated blast furnace slag, iron silicate, silica fume, and steel slag. A microstructural characterization was carried out through an optical microscope, X-ray diffraction analysis, and FT-IR. Also, a pozzolanic test was performed to study the reaction of SCMs silico-aluminous components. The formation of calcium silica hydrate was observed in all SCMs pozzolanic test. Steel slag, iron silicate, and ground granulated blast furnace slag required further milling to enhance cement reaction. Moreover, the tensile strength of three fibers (polypropylene, steel, and glass fibers) was tested after exposure to an alkalinity environment at ambient temperature during one and three months. Results show an alkaline environment entails a tensile strength decrease... [more]

The electronic oxygen regulator (EOR) is a new type of aviation oxygen equipment which uses electronic servo control technology to control breathing gas pressure. In this paper, the control method of EOR was studied, and the dynamic model of the aviation oxygen system was established. A disturbance-observer-based controller (DOBC) was designed by the backstepping method to achieve the goal of stable and fast breath pressure control. The sensitivity function was proposed to describe the effect of inspiratory flow on breath pressure. Combined with the frequency domain analysis of the input sensitivity function, the parameters of the DOBC were analyzed and designed. Simulation and experiment studies were carried out to examine the control performance of DOBC in respiratory resistance and positive pressurization process under the influence of noise and time delay in the discrete electronic control system, which could meet the aviation physiology requirements. The research results not only... [more]

Accurate forecasting of a building thermal performance can help to optimize its energy consumption. In addition, obtaining the Heat Loss Coefficient (HLC) allows characterizing the thermal envelope of the building under conditions of use. The aim of this work is to study the thermal inertia of a building developing a new methodology based on Long Short-Term Memory (LSTM) neural networks. This approach was applied to the Rectorate building of the University of Basque Country (UPV/EHU), located in the north of Spain. A comparison of different time-lags selected to catch the thermal inertia has been carried out using the CV(RMSE) and the MBE errors, as advised by ASHRAE. The main contribution of this work lies in the analysis of thermal inertia detection and its influence on the thermal behavior of the building, obtaining a model capable of predicting the thermal demand with an error between 12 and 21%. Moreover, the viability of LSTM neural networks to estimate the HLC of an in-use build... [more]

Drilling boreholes in gas zones and in zones with the possibility of migration or gas exhalation requires a high index of well tightness. An important parameter determining the effectiveness of sealing the annular space is the adhesion of the cement sheath to the rock formation. Low values of adhesion of the cement sheath to the rock formation and to the casing surface result in the formation of uncontrolled gas flows. The lack of adhesion also reduces the stabilization of the pipe column. To obtain the required adhesion, the annular space should be properly cleaned. Thorough removal of filter cake from the drilling fluid increases adhesion and reduces gas migration from the annular space. Therefore, in this work, the authors focus on determining the effect of cleaning the annular space on the adhesion of the cement sheath to the rock formation. The results of the research work allow for further research on the modification of spacers and cement slurries in order to obtain the required... [more]

A DC converter with the benefits of reverse power capability, less switching loss and wide voltage operation is presented and implemented for wide input voltage applications such as fuel cell energy, photovoltaic (PV) system and DC wind power. Two full bridge resonant circuits are used in the presented converter to achieve bidirectional power flow capability and reduce switching losses on active devices. To overcome the wide input DC voltage variation problem for fuel cell energy and PV solar panel, the topology morphing between the half bridge circuit and full bridge circuit is adopted on the primary side to obtain low (or high) voltage gain under a high (or low) input voltage condition. Therefore, the stable DC voltage is controlled at the load side by using the variable switching frequency modulation. The studied hybrid CLLC converter is tested by a 1 kW prototype and the performance is verified and confirmed by experiments.

Magnetic beamforming techniques can enhance the power transfer efficiency using focused magnetic fields by the multiple transmitters to the receivers. However, the intra-couplings that cause power leakage and phase distortion among the arrayed coils inevitably occur due to the deployment of coils having strong couplings between each other. Here, we analyze the adverse influences of intra-couplings and present the advantages of magnetically independent transmitters for multiple-inputs and single-output (MISO) WPT. The independent coil array can achieve focused magnetic fields by simply adjusting the amplitude of the transmitter voltage source without phase adjustment. The system also can eliminate the reactive power with the independent coil array to efficiently use the supplying power from the source. The analytical studies are verified by numerical and circuit simulation and experiments. Our analysis can be generalized to the MISO-WPT with an arbitrary number of transmitters. It can p... [more]

The large-scale interconnection of the power grid has brought great benefits to social development, but simultaneously, the frequency of large-scale fault accidents caused by extreme weather is also rocketing. The power grid is regarded as a representative complex network in this paper to analyze its functional vulnerability. First, the actual power grid topology is modeled on the basis of the complex network theory, which is transformed into a directed-weighted topology model after introducing the node voltage together with line reactance. Then, the algorithm of weighted reactance betweenness is proposed by analyzing the characteristic parameters of the power grid topology model. The product of unit reliability and topology model’s characteristic parameters under extreme weather is used as the index to measure the functional vulnerability of the power grid, which considers the extreme weather of freezing and gale and quantifies the functional vulnerability of lines under wind load, ic... [more]

In many electrical grids, the share of renewable energy generation increases. As these generators are typically connected to the grid via inverters, the level of grid inertia decreases. Such grids may therefore suffer from high rates of change of frequency during power imbalances. Modern wind turbines can help in controlling the frequency in such grids by providing synthetic inertia. A controller to provide synthetic inertia with wind turbines was developed at the Wind Energy Technology Institute in collaboration with Suzlon Energy. For this controller the influence of providing synthetic inertia on the mechanical loads of the wind turbine is assessed for different grid frequency scenarios. Such a scenario-based load analysis has not been published before, especially as the scenarios are derived from real measurements. The effect of the loads strongly depends on the analyzed grid frequency behavior. Ten months of high quality grid frequency measurements of the Indian grid are analyzed... [more]

In the present study, we provide useful data related to one of the most promising materials in thin-film solar cell technologies: Cu2ZnSnS4 (CZTS) kesterite structures. Sol-gel spin coating and chemical bath deposition methods were used to fabricate and further investigate Mo/CZTS/CdS/ZnO/AZO heterostructures. In order to examine the crystal structure of the samples, Raman scattering measurements using two excitation wavelengths (514.5 nm and 785 nm) were performed. Three Raman bands related to CZTS were found, as well as one that had its origin in CdS. By using laser ablation and performing Raman spectroscopy on these modified samples, it was shown that during the manufacturing process a MoS2 interlayer was formed between the CZTS and Mo layers. Our method proved that the CZTS layer in a multilayer device structure fabricated by solution-based methods can be decomposed, and thus a detailed analysis of the layer can be performed. Subsequently, current-voltage curves were investigated i... [more]

In this paper, the authors discuss the problem of the influence of the level of electrification in African countries on their sustainable development. The first aim of the article is to determine the relationship between changes in the electrification index and changes in the indicators showing individual components of sustainable development for African countries. The analyzed indicators of sustainable development include GDP per capita, Human Deveopment Index (HDI), and the CO2 emissions per capita indicator. The second goal of the article was to develop a synthetic indicator of sustainable development. This study uses the method of relationship research based on Gray Systems Theory—Gray Incidence Analysis. The main conclusion from the research carried out is that improving access to electricity is a necessary condition for the sustainable development of African countries. The lack of improvement in the availability of electricity is a basic barrier to development, especially in the... [more]