A substantial share of the building sector in global energy demand has attracted scholars to focus on the energy efficiency of the building sector. The building’s energy consumption has been projected to increase due to mass urbanization, high living comfort standards, and, more importantly, climate change. While climate change has potential impacts on the rate of energy consumption in buildings, several studies have shown that these impacts differ from one region to another. In response, this paper aimed to investigate the impact of climate change on the heating and cooling energy demands of buildings as influential variables in building energy consumption in the city of Poznan, Poland. In this sense, through the statistical downscaling method and considering the most recent Typical Meteorological Year (2004−2018) as the baseline, the future weather data for 2050 and 2080 of the city of Poznan were produced according to the HadCM3 and A2 GHG scenario. These generated files were then u... [more]

Biomass occupies a very important place among renewable energy sources, and the residual biomass recovery chain represents a sector of fundamental importance. Our work focused on the production of pellets by pruning residues from two of the most important woody crops in Italy: hazelnut and olive groves. We found a higher value of bulk density for the hazelnut pellet (581.30 kg m−3 vs. 562.38 kg m−3) and a higher value of length for the olive pellet (16.66 mm vs. 10.47 mm). The percentages of durability were very similar (98%). The low heating value and ash content of hazelnut and olive were 17.21 MJ kg−1 and 3.1%, and 16.83 MJ kg−1 and 2.5%. A higher concentration of Cu, Pb, and Ni was observed in the hazelnut. The contrary was observed for the concentration of Zn. N content was 0.77% and 1.24% for the hazelnut and the olive, respectively. The concentration of S was 0.00% for both. The quality parameters that do not meet current standards could be improved by mixing these materials wit... [more]

During the last decades, there has been great interest in the research community with respect to PV-Wind systems but figures show that, in practice, only PV-Diesel Power Systems (PVDPS) are being implemented. There are some barriers for the inclusion of wind generation in hybrid microgrids and some of them are economic barriers while others are technical barriers. This paper is focused on some of the identified technical barriers and presents a methodology to facilitate the inclusion of wind generation system in the design process in an affordable manner. An example of the application of this methodology and its results is shown through a case study. The case study is an existing PVDPS where there is an interest to incorporate wind generation in order to cope with a foreseen increase in the demand.

This research looked at the state of soils faced with urbanization processes in the Arctic region of the Yamal-Nenets Autonomous District (YANAO). Soils recently used in agriculture, which are now included in the infrastructure of the cities of Salekhard, Labytnangi, Kharsaim, and Aksarka in the form of various parks and public gardens were studied. Morphological, physico-chemical, and agrochemical studies of selected soils were conducted. Significant differences in fertility parameters between urbanized abandoned agricultural soils and mature soils of the region were revealed. The quality of soil resources was also evaluated in terms of their ecotoxicology condition, namely, the concentrations of trace metals in soils were determined and their current condition was assessed using calculations of various individual and complex soil quality indices.

Mineral resource estimation involves the determination of the grade and tonnage of a mineral deposit based on its geological characteristics using various estimation methods. Conventional estimation methods, such as geometric and geostatistical techniques, remain the most widely used methods for resource estimation. However, recent advances in computer algorithms have allowed researchers to explore the potential of machine learning techniques in mineral resource estimation. This study presents a comprehensive review of papers that have employed machine learning to estimate mineral resources. The review covers popular machine learning techniques and their implementation and limitations. Papers that performed a comparative analysis of both conventional and machine learning techniques were also considered. The literature shows that the machine learning models can accommodate several geological parameters and effectively approximate complex nonlinear relationships among them, exhibiting su... [more]

The decarbonisation of heating in the United Kingdom is likely to entail both the mass adoption of heat pumps and widespread development of district heating infrastructure. Estimation of the spatially disaggregated heat demand is needed for both electrical distribution network with electrified heating and for the development of district heating. The temporal variation of heat demand is important when considering the operation of district heating, thermal energy storage and electrical grid storage. The difference between the national and urban heat demands profiles will vary due to the type and occupancy of buildings leading to temporal variations which have not been widely surveyed. This paper develops a high-resolution spatiotemporal heat load model for Great Britain (GB: England, Scotland a Wales) by identifying the appropriate datasets, archetype segmentation and characterisation for the domestic and nondomestic building stock. This is applied to a thermal model and calibrated on th... [more]

Natural gas hydrates (GHs) filling sand layer pores are the most promising GHs that can be produced via conventional mechanisms in deep-sea environments. However, the seismic tracking of such thin GH-bearing sand layers is subject to certain limitations. For example, because most GH-bearing sand layers are thin and sparsely interbedded with mud layers, conventional seismic data with a maximum resolution of ~10 m are of limited use for describing their spatial distribution. The 2010 Ulleung Basin drilling expedition identified a relatively good GH reservoir at the UBGH2-6 site. However, the individual GH-bearing sand layers at this site are thin and cannot therefore be reliably tracked using conventional seismic techniques. This study presents a new thin layer tracking method using stepwise seismic inversion and 3D seismic datasets with two different resolutions. The high-resolution acoustic impedance volume obtained is then used to trace thin layers that cannot be harnessed with conven... [more]

The possibility to monitor and evaluate power system stability in real-time is in growing demand. Whilst most stability-related studies focus on long-term voltage stability and frequency stability, very little attention is given to the issue of short-term (voltage) instability. In this paper, the most common evaluation methods present in the literature are summarized, with a focus on their applicability to modern power systems with a large amount of renewable energy integration. The paper presents a first-of-a-kind structured review of this topic. We find that all existing methods have noteworthy limitations that necessitate further improvements. Additionally, the need of having an inclusive short-term instability prediction method is demonstrated, due to strong interactions between various short-term instability mechanisms. These findings provide a good foundation for further research and advancement in the field of real-time stability monitoring.

In this paper, we consider the problem of state-of-charge estimation for rechargeable batteries. Coulomb counting is a well-known method for estimating the state of charge, and it is regarded as accurate as long as the battery capacity and the beginning state of charge are known. The Coulomb counting approach, on the other hand, is prone to inaccuracies from a variety of sources, and the magnitude of these errors has not been explored in the literature. We formally construct and quantify the state-of-charge estimate error during Coulomb counting due to four types of error sources: (1) current measurement error; (2) current integration approximation error; (3) battery capacity uncertainty; and (4) timing oscillator error/drift. It is demonstrated that the state-of-charge error produced can be either time-cumulative or state-of-charge-proportional. Time-cumulative errors accumulate over time and have the potential to render the state-of-charge estimation utterly invalid in the long term.... [more]

Lining is often used as the last line of defense in deep large section chamber. Under the asymmetric load, it is easy to damage, resulting in the overall repair of the chamber. Aiming at this problem, taking the pump house in Wanfu Coal Mine under construction in China as an engineering example, we analyzed the asymmetric failure of pump house lining caused by construction disturbance, established the lining mechanical model and quantitative evaluation indexes, such as bending moment change rate, bending moment balance rate, displacement change rate and displacement balance rate, studied the influence mechanism of asymmetrical coefficient, section size and lining thickness on the mechanical behavior of lining, and proposed the control measures of deep large section chamber with the core of “strengthening asymmetric support, reducing section size and improving lining strength”. The field monitoring shows that the asymmetric deformation of the pump house is effectively controlled, and th... [more]

It is well known that the water hammer phenomenon can lead to pipeline system failures. For this reason, there is an increased need for simulation of hydraulic transients. High-density polyethylene (HDPE) pipes are commonly used in various pressurised pipeline systems. Most studies have only focused on water hammer events in a single pipe. However, typical fluid distribution networks are composed of serially connected pipes with various inner diameters. The present paper aims to investigate the influence of sudden cross-section changes in an HDPE pipeline system on pressure oscillations during the water hammer phenomenon. Numerical and experimental studies have been conducted. In order to include the viscoelastic behaviour of the HDPE pipe wall, the generalised Kelvin−Voigt model was introduced into the continuity equation. Transient equations were numerically solved using the explicit MacCormack method. A numerical model that involves assigning two values of flow velocity to the conne... [more]

This paper identifies and explores regulatory issues that may have an impact on the use of flexibility services by distribution utilities to solve grid constraints. This can be done by flexible distributed energy resources which can be instructed, for instance, to reduce export generating capacity or increasing consumption. We want to identify how regulation can better support the development of the future distribution utility in its role as neutral market facilitator, enabling more competition in local flexibility markets and optimal use of resources. A set of questionnaires were designed to capture the insights around important aspects of the regulation of flexibility markets (utilities’ network incentives, network tariff structure, market design for flexibility markets, etc.). These were sent to distribution utilities, energy regulators, energy marketplaces, energy associations and relevant experts from seven jurisdictions. The responses suggest a collective interest in the procurem... [more]

The efficiency of solar photovoltaic (PV) panels is greatly reduced by panel soiling and high temperatures. A mechanism for eliminating both of these sources of inefficiencies is presented by integrating solar PV generation with a compressed air system. High-pressure air can be stored and used to blow over the surface of PV panels, removing present dust and cooling the panels, increasing output power. A full-system mathematical model of the proposed system is presented, comprised of compressed air generation and storage, panel temperature, panel cleaning, and PV power generation. Simulation results indicate the benefit of employing compressed air for cleaning and cooling solar PV panels. For a fixed volume of compressed air, it is advantageous to blow air over the panels early in the day if the panel is soiled or when solar radiation is most abundant with the highest achievable flow rate if the panel is clean. These strategies have been shown to achieve the greatest energy captures for... [more]

In many regions of the world, the winter period is a time of poor air quality, due primarily to the increased use of individual and district heating systems. As a consequence, the atmospheric air contains increased concentrations of both particulate matter and gaseous pollutants (as a result of “low” emissions at altitudes of up to 40 m and “high” emissions more than 40 m above ground level). In winter, the increased pollution is very often exacerbated by meteorological conditions, including air temperature, pressure, air speed, wind direction, and thermal inversion. Here, we analyze the concentrations of particulate matter (PM10, PM2.5, and PM1.0) and gaseous pollutants (H2S, SO2, and VOC) in the immediate vicinity of a large solid fuel-fired heat and power plant located in an urban agglomeration. Two locations were selected for analysis. The first was close to an air quality measurement station in the center of a multi-family housing estate. The second was the intersection of two mai... [more]

As a highly nonlinear system, the performance of proton exchange membrane fuel cell (PEMFC) is controlled by various parameters. If the effects of all parameters are considered during the performance optimization, low working efficiency and waste of resources will be caused. The development of sensitivity analysis for parameters can not only exclude the parameters which have slight effects on the system, but also provide the reasonable setting ranges of boundary values for simulation of performance optimization. Therefore, sensitivity analysis of parameters is considered as one of the methods to optimize the fuel cell performance. According to the actual operating conditions of PEMFC, the fluctuation ranges of seven sets of parameters affecting the output performance of PEMFC are determined, namely cell operating temperature, anode/cathode temperature, anode/cathode pressure, and anode/cathode mass flow rate. Then, the control variable method is used to qualitatively analyze the sensit... [more]

The formation of hydroquinone (HQ) clathrate and the guest behaviors of binary (CH4 + CO2) gas mixtures were investigated by focusing on an application to separate CO2 from landfill gases. Spectroscopic measurements show that at two experimental pressures of 20 and 40 bar, CO2 molecules are preferentially captured in HQ clathrates regardless of the gas composition. In addition, preferential occupation by CO2 is observed more significantly when the formation pressure and the CH4 concentration are lower. Because the preferential occupation of CO2 is found with binary (CH4 + CO2) gas mixtures regardless of the composition of the feed gas, a clathrate-based process can be applied to CO2 separation or concentration from landfill gases or (CH4 + CO2) mixed gases.

In the presence of a global pandemic (COVID-19), the relentless pressure on global decision-makers is to ensure a balancing of health (reduce mortality impacts), economic goals (income for livelihood sustenance), and environmental sustainability (stabilize GHG emissions long term). The global energy supply system is a dominant contributor to the GHG burden and deeply embedded in the economy with its current share of 85%, use of fossil fuels has remained unchanged over 3 decades. A unique approach is presented to harmonizing the goals of human safety, economic development, and climate risk, respectively, through an operational tool that provides clear guidance to decision-makers in support of policy interventions for decarbonization. Improving climate change performance as an integral part of meeting human development goals allows the achievement of a country’s environmental, social, and economic well-being to be tracked and monitored. A primary contribution of this paper is to allow a... [more]

This paper provides evidence on how the variability of the power produced by a wind farm and its revenue are affected by implementing a ramp-rate limitation strategy and by adding a storage device to the system. The wind farm receives penalties whenever the ramp-rate limitations are not respected and may be supported by batteries to avoid this scenario. In this paper, we model the battery usage as a discrete time homogeneous Markov chain with rewards thanks to which it is possible to simulate the state of the charge of the battery and to calculate the amount of penalties suffered by the wind farm during any period. An application is performed considering the power produced by a hypothetical wind turbine located in Sardinia (Italy) using real wind speed data and electricity prices from a period of 10 years. We applied the concept of ramp-rate limitation on our hourly dataset, studying several limitation scenarios and battery capacities.

This paper presents a new virtual reality (VR)-based approach to advanced learnings and experiences of the circular economy (CE) in the construction industry. The approach involves incorporating game design and a building information modelling (BIM) digital twin of a purposed CE prototype building. Our novel approach introduces VR environments designed to provide a visual representation of materials and components that can be reintroduced into the supply chain at the end of life and their removal procedures and material provenance. A case study methodology was applied to a purposely designed CE building, namely the Legacy Living Lab (L3). To reflect the real-life building, L3’s BIM model was combined with Unify game software to advance the literature in three key areas. First, the research investigates VR tools that will allow building designers to view and implement their strategies to advance CE design. Second, this research proposes an advanced VR tool to visualise the bill of quant... [more]

The combustion characteristics of a staged combustion cycle engine with an oxidizer-rich preburner were experimentally studied at different momentum ratios of multi-element injectors. Propellants were simultaneously supplied as a liquid−liquid−liquid system, and an injector was designed in which a swirl coaxial jet is sprayed. The injector burned the propellants in the inner chamber which had a temperature greater than 2000 K. To cool the combustion gas, a liquid oxidizer was supplied to the cooling channel outside the injector. To prevent the turbine blades from melting, the temperature of the combustion gas was maintained below 700 K. To confirm the combustion characteristics at different momentum ratios of the high-temperature combustion gas inside the injector and the low-temperature liquid oxidizer outside the injector, three types of injectors were designed and manufactured with different momentum ratios: MR 3.0, MR 3.3, and MR 3.7. In this study, the results of the combustion te... [more]

Investor emotional heterogeneity and oil dual attributes are the key factors that cause the asymmetry of risks in the international crude oil market. This paper uses the monthly data from April 2003 to October 2020 to identify the dynamic characteristics of oil’s commodity attribute and financial attribute, and this paper also analyzes the asymmetric characteristics of risk evolution and risk degree in the international crude oil market under the condition of oil returns heterogeneity. The empirical results show that: first, there is heterogeneity in the influence of oil attributes on the risk evolution and risk degree of the international crude oil market; second, the alternation of oil dual attributes has a significant asymmetric impact on the risk evolution of international crude oil market; third, the sudden change of international crude oil market risk caused by oil attributes is asymmetric under different oil returns trends. Based on the empirical conclusion, this paper puts forw... [more]

Fractured rock masses below the water table are a problem in underground excavations because of their low strength and high permeability. Nowadays, these negative connotations can be reduced with techniques such as injection of cement, microcement, or resins grouts. These materials increase the rock mass cohesion while reducing the flow of water through the discontinuities. This paper describes the work carried out to design a waterproofing screen for a three-storey underground basement located in a building near the Bilbao estuary (Northern Spain) and with problems of water seepage from the river. First, a survey of the rock mass is carried out. This survey shows the presence of highly fractured zones and the variability of the permeability as functions of the fractures. Subsequently, the effect on permeability caused by the injection of cement grouts and microcement is studied by means of two pilot injection boreholes and eight control boreholes. Finally, a behavioural model is propo... [more]

Durability is the most pressing issue preventing the efficient commercialization of polymer electrolyte membrane fuel cell (PEMFC) stationary and transportation applications. A big barrier to overcoming the durability limitations is gaining a better understanding of failure modes for user profiles. In addition, durability test protocols for determining the lifetime of PEMFCs are important factors in the development of the technology. These methods are designed to gather enough data about the cell/stack to understand its efficiency and durability without causing it to fail. They also provide some indication of the cell/stack’s age in terms of changes in performance over time. Based on a study of the literature, the fundamental factors influencing PEMFC long-term durability and the durability test protocols for both PEMFC stationary and transportation applications were discussed and outlined in depth in this review. This brief analysis should provide engineers and researchers with a fast... [more]

The properties and the applications of the main monocyclic aromatic hydrocarbons (benzene, toluene, ethylbenzene, styrene, and the three xylene isomers) and the industrial processes for their manufacture from fossil raw materials are summarized. Potential ways for their production from renewable sources with thermo-catalytic processes are described and discussed in detail. The perspectives of the future industrial organic chemistry in relation to the production of high-octane bio-gasolines and monocyclic aromatic hydrocarbons as renewable chemical intermediates are discussed.

The purpose of this paper is to explore the challenges of an old low-standard urban district with a strong historical and cultural heritage and propose more sustainable renovation solutions, acceptable for the residents and municipality. The challenges of physical renovation or refurbishment are complex due to poor condition of the buildings, municipal ownership and governance, mixed management with community and low rents, which are insufficient to cover the costs. The paper discusses the proposed solutions of living standards, supported by the research in two directions: (i) available resources and reuse of materials, (ii) developing a renovation guidance for inhabitants from the building physics perspective, including indoor environment quality. Challenges related to energy efficiency are addressed from the decision-making perspective to overcome the barrier of lack of motivation to invest in energy-efficient measures at the individual and community level. The interdisciplinary appr... [more]