This study proposes the experimental evaluation of alternative refrigerants with low global warming potentials (GWPs) such as R1234ze(E), R513A, and the mixture R516A as a drop-in replacement for R134a in a domestic refrigerator with a volumetric capacity of 513 L. Initially, the optimal charge for each refrigerant was defined based on the minimum energy consumption of the refrigerator, then the thermal and energy performance of the refrigerator was evaluated. Finally, a total equivalent warming impact analysis (TEWI) was performed. The main results indicated that the optimal charge of the alternative refrigerants was below that corresponding to R134a (105 g), of which R516A (86 g) presented the greatest charge reduction. Regarding the average temperature of the refrigerator compartments, very adequate thermal conditions were observed; thus, the alternative refrigerants showed very similar conditions to R134a. For the coefficient of performance (COP) and considering R134a as a referenc... [more]

The structure of large biomass circulating fluidized bed (BCFB) boilers is complex, and control schemes for coal-fired boilers cannot be simply applied to biomass boilers. Multivariable coupling and operational disturbances are also common issues. In this study, a state space model of a 130 t/h BCFB boiler was established under different operating conditions. Using the 100% operating point as an example, a model predictive controller was designed and tested under output disturbance and input disturbance conditions. The results show that the predictive control system designed in this study has a fast response speed and good stability.

The high-frequency vibration and resonance of armature assembly in the hydraulic servo valve are the main reasons for instability and failure. Magnetic fluid (MF) operating in the squeeze mode can be taken as an effective damper for resonance suppression in the servo valve. Due to excitation difficulty and the low signal-to-noise ratio of high-frequency vibration signals, the capability of MF to modify multiple-order modal damping ratios in a multi-degree-of-freedom system is still unclear. To reveal the mechanism of magnetic fluid for improving modal damping ratios, an algorithm for modal damping ratio identification is proposed. The modal damping ratios of the armature assembly with and without magnetic fluid are identified based on the tested resonance free decay responses. Four resonance frequencies of armature assembly are observed, and the corresponding damping ratios are identified. The equivalent modal damping ratios due to squeeze flow of MF are obtained. The results show that... [more]

A wireless charging system that supports a large sensor network not only needs to provide real-time charging services but also needs to consider the cost of construction in order to meet the actual applications and considerations. The energy transfer between mobile devices is extremely difficult, especially at large distances, while at close distances a wireless, fast-charging, automatic, and high-precision landing system would be required. However, previous studies that used wireless charging cars, wireless charging unmanned aerial vehicles (UAVs) alone, or wireless charging pads to build a large-scale wireless charging system could not meet the above two conditions at the same time. If we can make good use of the existing high-speed backbone transport, such as the vehicular ad hoc network (VANET), it can not only consider the cost of construction and the speed of movement but also support the real-time charging service required by large-scale sensor networks. In this work, we propose... [more]

The present paper discusses the modeling and analysis of a diesel−wind generating system capable enough to cater to the electrical power requirements of a small consumer group or society. Due to high variations of the load demand or due to changes in the wind speed, the frequency of the diesel−wind system will be highly disturbed, and hence to regulate the frequency and power deviations of the wind turbine system, an effective controller design is a necessary requirement, and therefore this paper proposes a novel controller design based on PID scheme. The parameters of this controller is effectively optimized through a new snake optimizer (SO) in an offline manner to minimize frequency and power deviations of an isolated diesel−wind system. The performance of SO-PID for the diesel−wind system is evaluated by considering the integral of time multiplied absolute error (ITAE), integral absolute error (IAE), and integral of time multiplied square error (ITSE). The results were calculated f... [more]

Guangxi is a typical developing region on the southern coast of China. The current issues encountered in the region’s development are that fossil energy accounts for about 80% of the energy structure, fossil fuels are heavily dependent on imports, and the self-sufficiency rate of resources is only 32%. These challenges have created a disparity between the current regional development state and the country’s dual carbon target. Under the premise of comprehensively considering the multi-sectors of electricity, industry, transportation, and heating, this paper presents a study on the energy system transition towards low-carbon development for Guangxi in four steps. Firstly, to demonstrate EnergyPLAN’s capability in energy modeling, a reference scenario for Guangxi is created using official yearbook data from 2020. Then, a short-term scenario is formulated to analyze the development of Guangxi’s energy system during the 14th Five-Year Plan. Furthermore, two mid-term scenarios are establish... [more]

Existing electric-field integral inversion methods have limited field application conditions, and they are difficult to arrange electric-field measurement points on high-span overhead lines. This paper proposes a non-intrusive voltage measurement method for overhead transmission lines based on the near-end electric-field integration method. First, the electric-field distribution under 10 kV lines is calculated by finite element simulation software. The electric-field distribution of the plumb line and the discrete integral node below the wire are analyzed. Then, based on traditional electric-field integration, a line-voltage-inversion measurement method based on near-end electric-field integration is proposed. In addition, a voltage-monitoring system based on near-end electric-field integration is constructed. Next, the numerical integration types, the number of integration nodes, and the scale coefficient of the near-end region of the inversion algorithm are optimized with the electri... [more]

To strike a better balance between gas quality and production cost of biomass-based syngas, a process for high-safety and cost-effective syngas production is designed and studied, which takes advantage of biomass O2-enriched air gasification with 40−70% O2 purity and methanation synthesis. Based on the simulation data, the process is evaluated from techno-economic aspects, including syngas composition, higher heat value (HHV), upper and lower explosive limits (UEL and LEL), toxicity, unit production cost (UPC) and levelized cost of energy (LCOE). Five kinds of biomass are studied as feedstock. The effects of O2 purity, methanation pressure, feedstock cost, and plant scale are determined, respectively. The results show that O2 purity is an important parameter for technical performance, while methanation pressure is a minor parameter except for exergy efficiency. With respect to cost indicators, feedstock cost, and plant scale are crucial variables; by contrast, O2 purity plays a relativ... [more]

Space heating is a necessity in Alaska; however, the use of heating fuels carries both economic and environmental costs. In the Fairbanks North Star Borough (FNSB), Alaska, most households utilize heating fuel oil as a primary source for home heating and firewood as a secondary source. In the FNSB, wood-burning devices are the principal source of fine particulate matter with a size of 2.5 microns or less, (PM2.5), but firewood is less expensive when compared to heating fuel oil. The FNSB has been designated as a nonattainment area for PM2.5, which has been linked to negative cardiopulmonary impacts and other adverse health consequences. Electric thermal storage heaters (ETSH) could help solve the PM2.5 problem by displacing firewood used for residential space heating. We use dichotomous choice contingent valuation (DC-CV) to estimate willingness to pay (WTP) for an ETSH program which would allow FNSB residents to offset 100 gallons of heating fuel oil annually. Certainty correction is... [more]

In the last few years, many innovative solutions have been presented to address the climate change crisis. One of the innovative solutions is the participation of community members in the collective production of solar electricity instead of individual production. The current study aims to provide a critical literature review of the collective production of solar electricity, which is called “community-shared solar” (CSS). Sixty-seven peer-reviewed publications were selected based on the setting up of a combination of related keywords. To analyze the concept of CSS in the existing literature, a multi-level perspective (MLP) framework was used to observe the CSS innovation at the niche, regime, and landscape levels. Four aspects, including the technical, economic, socio-political, and regulatory and institutional, were considered to evaluate those three levels. The results revealed that in the technical and economic aspects, CSS has reached maturity and internal momentum that can take i... [more]

Compared to conventional façades, adaptive façades (AFs) can adjust their properties in response to environmental changes and user requirements. Often performed through the integration of actuators, sensors, and control units, this provides benefits such as reduced energy consumption in buildings but also increases the complexity of the façade design. To efficiently deal with the higher complexity, this article aims to provide suitable decision support for the early design phase, identify suitable design goals, and compare these to previously implemented Afs (make-or-buy decision). There is particular focus on the AF-specific characteristics, as these are new compared to well-known conventional façades. To systematically develop decision support, requirements are identified in expert interviews and the literature, and the current state of the art is evaluated against these. Research gaps found in current methods are addressed in this article, and continuous decision support is develope... [more]

The evaluation of pore structure is critical in understanding reservoir characteristics. This study aims to analyze the microscopic pore structure characteristics of tight reservoirs from various provenances through physical property analysis, casting thin sections, scanning electron microscopy (SEM), and constant−rate mercury injection. The pore throat parameters of the Chang 7 reservoir were analyzed and compared to those of the Xin’anbian and the Heshui areas. The results show that intergranular pores dominate the pore type of the Chang 7 reservoir in the Xin’anbian area, followed by feldspathic dissolution pores, with high-necked and tubular throat content caused by weak compaction and dissolution, respectively. On the other hand, feldspar dissolution pores dominate the pore type of the Chang 7 reservoir in the Heshui area, followed by intergranular pores, with a high content of tube−bundle throats caused by dissolution and flake−bent flake throats caused by compaction. The differe... [more]

Seas and oceans offer great potential as a widely available source of clean and renewable energy near high energy consumption centers. This source of energy is a valuable option in the energy transition and in energy matrix decarbonization. Wave energy and an oscillating water column (OWC) device stand out as the types of ocean energy with the most potential. An onshore OWC requires locations with rocky outcrops and steeper slopes as the device needs to be physically installed and has lower energy dissipation due to friction with the seabed. However, Brazil has approximately 7490 km of coastlines, with various shoreline geometries and geomorphologies, some of which are very suitable for OWC implementation. Some authors have estimated that the Brazilian coast has a total potential of 114 GW, distributed between wave and tidal energy, with a great possibility of contributing to global decarbonization efforts. This study aimed to identify and quantify the potential of locations suitable f... [more]

Recently, the reverse osmosis (RO) process is widely used in the field of desalinating brackish water and seawater to produce freshwater, but the disadvantage of using this technology is the increase in the rates of electrical energy consumption necessary to manage these units. To reduce the rates of electrical energy consumption in RO desalination plants, geothermal energy and photovoltaic/thermal panels were used as preheating units to heat the feed water before entering RO desalination plants. The proposed system in this study consists of an RO desalination plant with an energy recovery device, photovoltaic/thermal panels, and a geothermal energy extraction unit. To evaluate the system performance, three incorporated models were studied and validated by previous experimental data. The results indicated that incorporating the geothermal energy and photovoltaic/thermal panels with the RO desalination plants has positive effects in terms of increasing productivity and reducing the rate... [more]

Energy in microgrids (MGs) can now be generated from a variety of renewable sources, but their effective and sustainable use is dependent on electrical energy storage (EES) systems. Consequently, the expansion of MGs is greatly reliant on EES systems. The high infiltration of electric vehicles (EVs) causes some problems for the smooth functioning of the electric power system. However, EVs are also able to offer ancillary services, such as energy storage, to power systems. The research presented in this paper aims to develop a novel frequency regulation (FR) approach for biogas diesel engines (wind), the organic Rankine cycle (ORC), and solar-based two-area islanded microgrids with EVs in both areas. This article discusses the introduction of a fuzzy logic controller (FLC) for FR with scaled factors configured as proportional integral (PI) and proportional derivative with filter (PDF), i.e., a FLC-SF-PI-PDF controller. A recently created modified dragonfly algorithm is used to determine... [more]

The aim of this review was to analyze to what extent the relationship between corporate social responsibility (CSR), environment and energy has been addressed in the specialized literature and which are the deficient segments in this regard. VOSviewer was used for data extraction, mapping and grouping the articles from journals that have been indexed in Web of Science (WOS). A total of 102 papers were found approaching the topic of corporate social responsibility, environment and energy policy, 5192 research papers for CSR and the environment and 320 on CSR and energy policy. Following the bibliometric analysis, we can conclude that we are facing a shortage of works that analyze the relationship between the three fields together. The number of published articles was reduced to establish the direction of influence between the three variables, as well as the impact between them. However, the advantage that emerges from this lack of works is that there are many opportunities to find news... [more]

Indonesia’s final energy demand is projected to increase by 70% in the next decade, with electricity expected to account for 32%. The increasing electricity demand poses a potential threat to national emissions reduction targets since fossil fuels generated 86% of the electricity in 2018, associated to 50% of the national CO2 emissions. Indonesia plans to reduce its CO2 emissions by 29% by increasing the total electricity generated from renewables, using a set of market-based and regulatory policies. However, economic, social, and environmental issues may arise from the widespread adoption of renewable energy. This study explores the economic, social, and environmental effects of renewable energy policies in the electricity sector. Our work presents an advance over previous studies that attempted to understand the electricity sector energy transition from a system perspective by exploring the structural feedback between it and economic, energy, and environmental systems. This enables t... [more]

Offshore wind farms are a current area of interest in Australia due to their ability to support its transition to renewable energy. Climate reanalysis datasets that provide simulated wind speed data are frequently used to evaluate the potential of proposed offshore wind farm locations. However, there has been a lack of comparative studies of the accuracy of wind speed predictions from different reanalysis datasets for offshore wind farms in Australian waters. This paper assesses wind speed distribution accuracy and compares predictions of offshore wind turbine power output in Australia from three international reanalysis datasets: BARRA, ERA5, and MERRA-2. Pressure level data were used to determine wind speeds and capacity factors were calculated using a turbine bounding curve. Predictions across the datasets show consistent spatial and temporal variations in the predicted plant capacity factors, but the magnitudes differ substantially. Compared to weather station data, wind speed pred... [more]

Renewable energy resources and energy efficiency measures are effective means of curtailing CO2 emissions. Solar and wind technologies have been mostly developed to meet the energy demand of off-grid remote areas or locations without grid connections. However, it is well-known that the power generation of these resources is affected by daily fluctuations and seasonal variability. One way to mitigate such an effect is to incorporate hydrokinetic resources into the energy system, which has not been well investigated yet. Therefore, this study examines the prospects of designing a hybrid system that integrates hydrokinetic energy to electrify an off-grid area. Hydrokinetic energy generation depends on water flow velocity (WFV). We estimate WFV by a model-based approach with geographical and weather data as inputs. Together with the models of the other components (wind turbine, PV panel, battery, and diesel generator) in the micro-grid, an optimization problem is formulated with the total... [more]

As conventional energy sources decrease and worldwide power demand grows, the appeal of photovoltaic (PV) systems as sustainable and ecofriendly energy sources has grown. PV system installation is influenced by geographical location, orientation, and inclination angle. Despite its success, weather conditions such as dust substantially influences PV module performance. This study provides a comprehensive review of the existing literature on the impact of dust characteristics on PV systems from three distinct perspectives. Firstly, the study looks at the dust properties in different categories: optical, thermal, physical, and chemical, highlighting their significant impact on the performance of PV systems. Secondly, the research reviews various approaches and equipment used to evaluate dust’s impact on PV, emphasizing the need for reliable instruments to measure its effects accurately. Finally, the study looks at modeling and predicting the influence of dust on PV systems, considering th... [more]

With the rapid growth of the power grid load and the continuous access of impact load, the range of power system frequency fluctuation has increased sharply, rendering it difficult to meet the demand for power system frequency recovery through primary frequency modulation alone. Given this headache, an optimal control strategy for battery energy storage participating in secondary frequency regulation of the power grid is proposed in this paper based on a double-layer structure. Besides, a coordinated control framework is constructed for energy storage battery joint units engaged in automatic generation control (AGC). At the dispatching level, the power allocation principle is set to coordinate the fast and slow resources of energy storage and conventional thermal power units, and the power decoupling of the two types of frequency modulation (FM) resources is completed. At the system level, a power allocation model representing the real-time frequency modulation capability of energy sto... [more]

Microgrid technology has recently gained global attention over increasing demands for the inclusion of renewable energy resources in power grids, requiring constant research and development in aspects such as control, protection, reliability, and management. With an ever-increasing scope for maximizing renewable energy output, there is also a need to reduce the curtailment of power on both the generation and demand sides by increasing forecasting accuracies and using resources more effectively. This paper proposes a dual-stage dispatch employing a novel “split-horizon” strategy, in a bid to enhance energy management in a standalone microgrid. The split-horizon is essentially the considered time horizon split into equal operational periods of the dual-stage dispatch. The proposed strategy utilizes a custom-designed novel variant of the inertia-weight-based particle swarm optimization (PSO), termed customized PSO, to perform the optimal schedule and dispatch operation by benefitting from... [more]

An electrical power system (EPS) is subject to unexpected events that might cause the outage of elements such as transformers, generators, and transmission lines. For this reason, the EPS should be able to withstand the failure of one of these elements without changing its operational characteristics; this operativity functionality is called N−1 contingency. This paper proposes a methodology for the optimal location and sizing of a parallel static Var compensator (SVC) in an EPS to reestablish the stability conditions of the system before N−1 contingencies take place. The system’s stability is analyzed using the fast voltage stability index (FVSI) criterion, and the optimal SVC is determined by also considering the lowest possible cost. This research considers N−1 contingencies involving the disconnection of transmission lines. Then, the methodology analyzes every scenario in which a transmission line is disconnected. For every one of them, the algorithm finds the weakest transmission... [more]

The thermal runaway (TR) behavior and combustion hazards of lithium-ion battery (LIB) packs directly determine the implementation of firefighting and flame-retardants in energy storage systems. This work studied the TR propagation process and dangers of large-scale LIB packs by experimental methods. The LIB pack consisted of twenty-four 60 Ah (192 Wh) LIBs with LiFePO4 (LFP) as the cathode material. Flame performance, temperature, smoke production, heat release rate (HRR), and mass loss were analyzed during the experiment. The results indicated that TR propagation of the LIB pack developed from the outside to the inside and from the middle to both sides. The development process could be divided into five stages corresponding to the combustion HRR peaks. In the initial stages, the main factor causing LFP battery TR under heating conditions was the external heat source. With the propagation of TR, heat conduction between batteries became the main factor. Hazard analysis found that the HR... [more]

The wide application of power electronic devices brings an increasing amount of undesired harmonic and interharmonic tones, and accurate harmonic phasor estimation under a complex signal input is an important task for smart grid applications. In this paper, an optimization of least-square dynamic harmonic phasor estimators, considering multi-interference and harmonic frequency variance, is proposed. A comprehensive error index (CEI) composed of the fundamental-leakage-led harmonic amplitude estimation error, harmonic mutual interference, out-of-band interference, and harmonic frequency deviation is employed. The largest CEI part of least-square algorithms using three different signal decomposition models is analyzed for the first time, and variables to reduce this error component are then introduced using singular value decomposition. With the CEI and defined variables, a minimum-error estimation of harmonic phasors under various interference and harmonic frequency change is discussed.... [more]