A daylighting control system that uses the closed loop proportional algorithm needs to be calibrated both during nighttime and daytime. The selection of the daytime calibration time can affect the behavior of the system and is usually performed when the ratio of the illuminance of the ceiling sensor (SD) to the illuminance at a point on the working plane (ED) is relatively large without sunlight patches in the ceiling photo-sensor’s field of view (FOV). However, this requirement is not associated with a specific value and can be achieved under a wide range of conditions related to the sky luminance distribution. In the present work, four ceiling sensors with different field of views (FOVs) were examined in a typical north-facing office space. The effect of daytime calibration on the system’s performance was estimated through the calculation of lighting energy savings and the overdimming percentage. The results show that the effect of both the FOV of the ceiling sensor and the daytime c... [more]

The radiation flux distributions produced by the concentrating solar systems used to produce thermal/electrical power are usually non-homogeneous. This results in non-uniform temperature distributions on the solar receivers, causing adverse effects on the system’s overall performance. An approach to better understand the problem is to study the surfaces around the focal zone where the radiation density is homogeneous (isosurfaces), generating them from experimental data. For this, it is necessary to superimpose built volumes of the different irradiance levels using parallel planes in different directions from the focal point of a concentrator. These volumes are known as effective volumes. This study presents the model used to generate effective volume produced by a point focus concentrator, comparing it with experimental results in a direction perpendicular to the focal axis. The effective volumes were developed considering a global optical error of the system of 2.8 mrad. The set of m... [more]

Two design flows of the Petri net-based cyber-physical systems oriented towards implementation in an FPGA are presented in the paper. The first method is based on the behavioural description of the system. The control part of the cyber-physical system is specified by an interpreted Petri net, and is described directly in the synthesisable Verilog hardware language for further implementation in the programmable device. The second technique involves splitting the design into sequential modules. In particular, adequate decomposition and synchronisation algorithms are proposed. The resulting modules are further modelled within the Verilog language as the composition of sequential automata. The presented design flows are supported by theoretical background, and templates of Verilog codes. The proposed techniques are illustrated by a real-life example of a multi-robot cyber-physical system, where each step of the proposed flows is explained in detail, including modelling, description of the... [more]

The liberalization of the gas market has deeply affected the structure of the gas system. The change from a vertically integrated utility structure to a liberalized architecture has resulted in a new network asset where aggregators could play a key role. To enable aggregators’ functionalities, the gas system has moved to a smart configuration. The development of this Advanced Metering Infrastructure (AMI) allowing a two-way communication between the utility and the consumers, together with demand response programs, prove to be an advantageous solution. Utilities are allowed to manage consumers’ gas load by asking them to reduce or shift their gas usage so that rebates or back payments could be available for consumers. In this framework, aimed at ensuring the feasibility of the gas system and promoting the aggregation of small gas loads, a new agent has been identified. In this research, the potential of district heating systems as gas market aggregators, together with a novel architect... [more]

Solar still, a small equipment using evaporation and condensation processes to get clean water, is expected to be widely used for sea/brackish water desalination, water purification, and wastewater treatment because of its convenient carrying, friendly environment, and low energy consumption. In recent years, considerable progress has been made in improving the productivity of solar still. This paper will reclassify the methods to improve the solar still by elevating the evaporation rate and condensation rate. The main methods increasing evaporation rate are as follows: (i) adding heat storage materials; (ii) using nanoparticles; (iii) changing structure of the absorption plate; and (iv) using photothermal materials. The primary methods increasing the condensation rate are as follows: (i) cooling the condensing surface; (ii) increasing the condensation area; (iii) changing the wettability of the condensing surface; and (iv) using a separate condenser. The advantages and disadvantages o... [more]

Increased use of energy in buildings and HVAC systems requires advanced control schemes like model-based control to improve energy efficiency, which in turn requires accurate thermodynamic models of buildings. The Resistive-Capacitive (RC) method is a popular and versatile approach for thermal modeling of buildings. Despite this, it is not easy to find practical solutions of implementation of the RC method. It is the goal of this paper to clarify the RC method and demonstrate simple implementation of this method, especially for multi-zone buildings, which have more potential for energy savings from use of model-based control. This paper provides two contributions. First is a detailed explanation of the RC method, focusing on its use for developing a structure of a model and first-principles approach for estimation of parameters of a model. Second is a demonstration of an algorithm that enables automatic development of the structure of a model from basic information about a building (la... [more]

Building an effective Machine Learning (ML) model for a data set is a difficult task involving various steps. One of the most important steps is to compare a substantial amount of generated ML models to find the optimal one for deployment. It is challenging to compare such models with a dynamic number of features. Comparison is more than only finding differences of ML model performance, as users are also interested in the relations between features and model performance such as feature importance for ML explanations. This paper proposes RadialNet Chart, a novel visualisation approach, to compare ML models trained with a different number of features of a given data set while revealing implicit dependent relations. In RadialNet Chart, ML models and features are represented by lines and arcs, respectively. These lines are generated effectively using a recursive function. The dependence of ML models with a dynamic number of features is encoded into the structure of visualisation, where ML... [more]

The increasing proportion of unconventional worldwide energy demands have consistently promoted the necessity for exploring a precise, high-resolution, objective, and quantitative stratigraphic division method for macroscopically homogeneous mudstone successions. The chemostratigraphy can resolve this problem well, although it has been applied successfully in North America, but not systematically studied in China for shale gas exploration and development. This work has conducted a chemostratigraphic analysis of Wufeng and Longmaxi Formation on the Changning section of Sichuan Province, southwestern China, to testify its applicability for shale gas exploration in China. Principal component analysis (PCA) was first employed to reduce the dimensionality of datasets. Three chemofacies, including detrital (K, Ti, Fe, Al, Na, Mg, Cr, Zr, Rb), authigenic (Ca, Sr, Mn, Si, S, Ba), and redox-organic (P, V, Ni, Zn, Cu, TOC), were found. Subsequently, constrained clustering analysis was utilized f... [more]

In the case of the inductive voltage transformer (VT), the resonance phenomenon may be the main reason for its poor transformation accuracy of the non-sinusoidal voltage. This problem mainly results from the leakage inductance and the parasitic capacitance of its primary winding. The application of the sinusoidal voltage with a frequency from 20 Hz to 20 kHz presented in this study ensures proper identification of the resonance frequencies of the medium-voltage (MV) inductive VTs. The results are consistent with the values obtained in the reference condition at their nominal primary voltage. Therefore, it is proven that the proposed solution is effective in all cases. The influence of the main frequency variation of the non-sinusoidal primary voltage on the resonance properties of the inductive VT is also studied. Moreover, the tests indicate that the capacitance of the load of the secondary winding may cause a decrease in their resonance frequency.

This paper deals with the applicability of alternative power system configurations to reduce the environmental footprint of inland waterway ships. Its original contribution includes: models for assessment of the lifetime emissions and associated lifetime costs of alternative power system configurations for different types of inland waterway vessels, identification of the most cost-effective options for these vessels, and an estimation of the impact of emission policies on the profitability of each option. The case study considers the Croatian inland waterway sector, where three types of vessel with significantly different purposes, designs, and operative profiles are considered (cargo ship, passenger ship, and dredger). The technical and operational features of these ships are analyzed with an emphasis on their energy needs. Then, life-cycle assessments (LCAs) of a diesel engine-powered ship configuration and two battery-powered ship configurations (with and without a photovoltaic syst... [more]

By combining the advantages of different energy storage technologies, the hybrid energy storage system (HESS) can satisfy the multiple requirements of prosumer systems. However, the required capacity of the HESS is larger than that of the single-battery energy storage system (ESS). This paper investigates the energy exchange within the HESS caused by the phase shift of the low-pass filter controller and its relevant impact on the HESS. The results show that unnecessary energy exchange results in an oversized capacity and increased energy loss. In addition, the increase in the time constant of the low-pass filter controller leads to a larger phase shift, further contributing to the increases in the total capacity and energy loss. Furthermore, this paper compares the single-battery ESS, the battery-supercapacitor HESS, and the battery-flywheel HESS implemented in a household-prosumer system along with a renewable energy source (RES). The comparison of the ESS combinations demonstrates th... [more]

Contemporary agriculture has become very energy-intensive and mainly uses electricity, which is needed for technological processes on livestock farms. Livestock faeces are burdensome for the environment due to the release of methane into the atmosphere. This article presents the concept of a self-sufficient livestock farm as an off-grid energy circuit that is a part of the agricultural process. The key idea is to obtain an energy flow using the concept of a smart valve to achieve a self-sufficient energy process based on a biogas plant, renewable energy sources, and energy storage. During the production process, a livestock farm produces large amounts of waste in the form of grey and black manure. On the one hand, these products are highly harmful to the environment, but on the other, they are valuable input products for another process, i.e., methane production. The methane becomes the fuel for cogeneration generators that produce heat and electricity. Heat and electricity are partly... [more]

Due to the complex and variable conditions under which wind turbines operate, existing working condition classification methods are inadequate for condition assessment of the main transmission system. Because working conditions are too few after classification, it cannot effectively describe the complex and variable working conditions of wind turbine. This can lead to high false-alarm rates in the condition monitoring, which affect normal operations. This paper proposes a working condition classification method for the main transmission system of wind turbines based on supervisory control and data acquisition (SCADA) data. Firstly, correlation analysis of SCADA data acquired by wind farm is used to select the parameters relevant to the main transmission system. Secondly, according to the wind turbine control principle, the working conditions are initially divided into four phases: shutdown, start-up, maximum wind energy tracking, and constant speed. The k-means clustering algorithm is... [more]

This work presents a comprehensive theoretical analysis of current-mode power amplifiers as a function of input power for different biasing classes under the common simplifying assumption of constant transconductance and hard current cut-off/saturation. Typically, the theoretical analysis of power amplifier performance and behavior are carried out only at maximum output power. However, to achieve high data-rates, modern telecommunication systems adopt signals characterized by a very high peak-to-average power ratio, thus it is useful to analyze the power amplifier behavior as a function of power back-off. Moreover, in many cases, to enhance the efficiency and/or to apply harmonic shaping techniques, a clipped drain-source current, which approaches a square wave, is required. The classical analysis can be extended to low power levels only under the assumption of power-independent conduction angle, which is true only for class-A and class-B amplifiers, and does not take into account poss... [more]

There are two kinds of working mechanisms for the Stirling cycle, i.e., the positive and the reverse cycles, and a Stirling engine (SE) can be operated as a Stirling refrigerator (SR). This indicates that a probable practical method for evaluating the performance of a Stirling engine is to run it as a refrigerator, which is much easier to operate. For this purpose, an improved Simple model for both the positive and the reverse Stirling cycles, considering the various loss mechanisms and actual operating conditions, is proposed and verified by a self-designed Stirling engine. As to the positive cycle with helium and nitrogen at 2.8 MPa, the model errors range from 5.4−11.3% for the indicated power, and 1−10.2% for the cycle efficiency. As to the reverse cycle with helium and nitrogen, the errors of the predicted input power range from 7.9−15.3% and from 2.5−10.9%, respectively. The experimental cooling temperatures can reach −92.2 and −53.6 °C, respectively, for the reverse cycle with t... [more]

Biogas has increasingly been used as an alternative to fossil fuels in the world due to a number of factors, including the availability of raw materials, extensive resources, relatively cheap production and sufficient energy efficiency in internal combustion engines. Tightening environmental and renewable energy requirements create excellent prospects for biogas (BG) as a fuel. A study was conducted on a 1.6-L spark ignition (SI) engine (HR16DE), testing simulated biogas with different methane and carbon dioxide contents (100CH4, 80CH4_20CO2, 60CH4_40CO2, and 50CH4_50CO2) as fuel. The rate of heat release (ROHR) was calculated for each fuel. Vibration acceleration time, sound pressure and spectrum characteristics were also analyzed. The results of the study revealed which vibration of the engine correlates with combustion intensity, which is directly related to the main measure of engine energy efficiency—break thermal efficiency (BTE). Increasing vibrations have a negative correlation... [more]

This work analyzes the possibility of a provision of force-majeure mode of the combat vehicles with the aid of disk construction installed in the baffler, the base of the operation of which is the method of residual cyclical quadratic chain code of construction of the “windows” of the movable disk. To determine the optimal parameters of the moving disk of the rotor system, mathematical modeling was performed. The results of mathematical modeling were used to create a PC-based calculation program. The calculation was performed for the rotational frequency ω = 300 s−1 andfor harmonic numbers from 1 to 100. The waveforms used in simulation were as follows: quasi-trapezoidal and rectangular. It is established that at the number of “windows” m = 276 in the moving disk of the rotor system the radiation spectrum acquires a uniform distribution. The object of the research is the process of extreme burning of fuel material in the combat vehicles’ engines, ensuring, according to the technical po... [more]

The rapid growth of the Information and Communications Technology (ICT) sector requires additional infrastructure, such as more micro-datacenters and telecom stations, to support the higher internet speeds and low latency requirements of 5G networks. The increased power requirements of the new ICT technologies necessitate the proposal of new power supplies, in an attempt to support the increase in energy demand and running costs. This work provides an in-depth theoretical analysis on the losses of the individual stages of commercially available PSU and proposes a new multicell PSU, the buck PFC converter, which offers a higher overall efficiency at varying load levels. The theoretical results are verified using simulation results, via a PSIM Thermal Module, and using experimental data. The results indicate that multicell structures can improve the overall PSU efficiency by 1.2% at 50% rated power and more than 2.1% at full power. Finally, taking into consideration the economic implicat... [more]

The aim of the study is to explore the intellectual structure of the field and fronts in research on energy efficiency in the context of cloud computing and thus to contribute to science mapping of the research field. The research process was driven by the following study questions: (1) what are the most influential publications in the research field? and (2) what are the research fronts in the research field? The method of direct citation analysis was employed in the research process. Data for analysis were obtained from the Scopus database and analyzed with the use of VOSviewer science mapping software. In response to the first question, we identified the most influential publications in the research field and analyzed their types (i.e., whether they are original research papers or rather the “context” papers e.g., survey or review papers, framework papers, challenges papers, and study papers). Moreover, a comparison analysis between the types of papers among the most cited “classica... [more]

A good thermal environment is important in a place where occupants stay for a long time. Since heating a house consumes a lot of energy, an energy-efficient heating method will be required. Then, by combining a heat pump and underfloor heating, there is a possibility that both thermal comfort and energy saving can be achieved. The survey was conducted on a detached house located in Nagano Prefecture, Japan. The average outside air temperature was 4.2 °C. This study investigated the indoor thermal environment, evaluated the operating performance of the heat pump, and calculated the heat load by two-dimensional analysis. More than 80% of the subjects were satisfied with the thermal environment and the neutral temperature was 18.9 °C. In the operation of the heat pump, defrost operation was confirmed, but the average COP was 2.9, and it operated efficiently. In addition, the heat loss from the foundation slab was examined. Proper insulation placement has shown the potential to reduce heat... [more]

Wax precipitation and deposition are serious flow assurance problems. Wax precipitation is investigated simultaneously using centrifugation and high-temperature gas chromatography (C-HTGC) to obtain the amount and component distribution of precipitated wax in artificial waxy oil and diesel at different temperatures. However, the conventional C-HTGC method gives upper measurements of the amount of precipitated wax, as it ignores wax dissolved in crude oil in the centrifugal cake. A modified C-HTGC method was developed to obtain the precipitated solid fraction of crude oil, based on the mass balances of the non-crystallized fraction of the centrifuged cake. The weight, percent and carbon number distribution of precipitated solid wax crystals at different temperatures of artificial oil and 0# diesel were obtained. It was found that wax precipitation characteristics are affected by many factors, including the carbon number distribution of the oil, the sensitivity of alkane crystallization... [more]

Indonesia has an increasing electricity demand that is mostly met with fossil fuels. Although Indonesia plans to ramp up Renewable Energy Technologies (RET), implementation has been slow. This is unfortunate, as the RET potential in Indonesia might be higher than currently assumed given the archipelago’s size. However, there is no literature overview of RET potentials in Indonesia and to what extent they can meet current and future electricity demand coverage. This paper reviews contemporary literature on the potential of nine RET in Indonesia and analyses their impact in terms of area and demand coverage. The study concludes that Indonesia hosts massive amounts of renewable energy resources on both land and sea. The potentials in the academic and industrial literature tend to be considerably larger than the ones from the Indonesian Energy Ministry on which current energy policies are based. Moreover, these potentials could enable a 100% renewables electricity system and meet future de... [more]

Disposal of municipal solid wastes (MSW) remains a challenge to minimize its impacts on the environment and human health. Landfilling, currently the most common method used for MSW disposal, occupies land space and leads to soil and air emissions. Gasification, an alternative MSW disposal method, can convert waste to energy, but can also lead to soil and air emissions and is a more extensive operation. In this study, life cycle assessments (LCA) of the two disposal methods (landfilling without energy recovery and gasification) were compared to understand impacts on environment and health. The LCA was conducted following the ISO 14040 standards with one ton of MSW as the functional unit. The life cycle inventory was obtained from published journals, technical reports, LandGEM, HELP and GREET database. The impact assessment was done using TRACI 2.1 and categorized into eight groups. The LCA revealed that landfilling is a higher contributor in global warming, acidification, smog formation... [more]

The process of underground coal mining fractures the overlying strata and may provide storage and transportation space for gas by changing the roof rock permeability, which is released by pressure after mining. This paper adopts the experimental method of physical similarity simulation and combines the fractal theory to study the permeability characteristics of the fracture network after mining, and it establishes the fractal permeability equation of pressure-relief gas. The results of the study show that the fracture opening shows a positive correlation with the overburden permeability, whereas the tortuosity of the fracture shows a negative correlation with the overburden permeability. The shape of the high permeability area in the fracture network is found to be similar to the hat-shaped elliptical parabolic zone. In the process of permeability evolution, the key layer structure of the overburden rock is considered as the main factor that affects the trend of change in permeability.... [more]

In this paper, the properties of ignition of mixed fuel pellets formed on the basis of fairly typical energy coal and wood industry waste in the form of cedar husks are experimentally established. The technical characteristics of the initial fuel components and the mixtures based on them, the ignition delay times for different mass concentrations of biomass in coal, and the composition of flue gases formed during the thermal decomposition of these mixed fuels and their base components were determined. Pellets of mixed fuels were made by a hydraulic press. The experiments were performed in an air environment at temperatures from 600 °C to 800 °C. Recording of the processes of pellet ignition and combustion was carried out using a high-speed video camera with an image format of 1024 × 1024 pixels, and a frame rate up to 500 frames per second. The analysis of the flue gas composition was performed using a Test-1 factory gas analyzer (BONER Co.). It was found that the increase in the share... [more]