The injection of carbon dioxide (CO2) is an essential technology for maximizing the potential of hydrocarbon reservoirs while reducing the impact of greenhouse gases. However, because of the complexity of this injection, there will be many different chemical reactions between the formation fluids and the rock minerals. This is related to the clay content of sandstone reservoirs, which are key storage targets. Clay content and clay types in sandstone can vary substantially, and the influence of these factors on reservoir-scale CO2-water-sandstone interactions has not been managed appropriately. Consequently, by simulating the process of CO2 injection in two different clay-content sandstones (i.e., high- and low-clay content), we investigated the effect of the sandstone clay concentration on CO2-water-sandstone interactions in this article. High clay content (Bandera Grey sandstone) and low clay content (Bandera Brown sandstone) were considered as potential storage reservoirs and their r... [more]

The aim of this research is to investigate the effects of rheological models of shear-thinning fluids and their estimated parameters on the predictions of laminar, transitional, and turbulent flow. The investigation was carried out through experimental and computational fluid dynamics (CFD) studies in horizontal pipes (diameters of 19.1 mm and 76.2 mm). Six turbulent models using Reynolds averaged Navier−Stokes equations in CFD_ANSYS Fluent 19.0 were examined in a 3D simulation followed by comparison studies between numerical and experimental results. Regarding results of laminar regions in power-law rheology models, Metzner and Reed presented the best fit for the pressure loss and transitional velocity. For the turbulent region, correlations observed by Wilson and Thomas as well as Dodge and Matzner had good agreement with the experimental results. For Herschel−Bulkley fluids, pressure losses and transitional regions based on a yielded region were examined and compared to the experime... [more]

The modular multilevel matrix converter (M3C) is the core component in low-frequency AC (LFAC) transmission, which is a competitive scheme for offshore wind power integration. In this paper, the M3C control strategy with the reduced switching frequency SM voltage balancing method is proposed. First, based on the conventional αβ0 and dq transformations, the M3C mathematical model is derived. Then, the dual-loop control structure with outer loop and inner loop controllers commonly used in voltage source converters is applied to the M3C. The inner loop controller consists of the current tracking controller in the dq reference frame and the circulating current suppressing controller in the αβ0 reference frame; the outer loop controller is proposed for the offshore wind farm LFAC integration scenario. Additionally, according to the operating characteristics of full-bridge sub-modules (FBSMs), three characteristic variables are defined and a reduced switching frequency SM voltage balancing m... [more]

In an era of rapid technological improvements, state-of-the-art methodologies and tools dedicated to protecting and promoting our cultural heritage should be developed and extensively employed in the contemporary built environment and lifestyle. At the same time, sustainability principles underline the importance of the continuous use of historic or vernacular buildings as part of the building stock of our society. Adopting a holistic, integrated, multi-disciplinary strategy can link technological innovation with the conservation and restoration of heritage buildings. This paper presents the ongoing research and results of the application of Machine Learning methods for the remote monitoring of the built environment of the historic cluster in Cypriot cities. This study is part of an integrated, multi-scale, and multi-disciplinary study of heritage buildings, with the end goal of creating an online HBIM platform for urban monitoring.

In thermally modernised buildings, sharing of ventilation heat loss becomes more significant. In the case of the application of ventilation with heat recovery, especially during transitional periods, there arises a question of whether an air system makes it possible to maintain the required indoor air temperature without the necessity of using a basic hydronic heating system. This paper presents the application of a simple thermal network model of a building zone to simulate indoor air temperature in a single room of a multi-storey building with a mechanical ventilation system with heat recovery. Ventilation air was supposed to be the only heat source and its ability to maintain the required indoor air temperature was checked in simulations and then compared with measurements. The 5R1C thermal network model of a building zone was used for simulations. Comparison with measurements showed the Mean Absolute Error (MAE) and Root Mean Square Error (RMSE) of indoor air calculation to be 2.37... [more]

Development and optimization of the membrane distillation (MD) process are strongly associated with better understanding of heat and mass transport across the membrane. The current state-of-the-art on heat and mass transport in MD greatly relies upon the use of various empirical correlations for the Nusselt number (Nu), tortuosity factor (τ), and thermal conductivity (κm) of the membrane. However, the current literature lacks investigations about finding the most representative combination of these three parameters for modeling transport phenomena in MD. In this study, we investigated 189 combinations of Nu, κm, and τ to assess their capability to predict the experimental flux and outlet temperatures of feed and permeate streams for hollow fiber MD modules. It was concluded that 31 out of 189 tested combinations could predict the experimental flux with reasonable accuracy (R2 > 0.95). Most of the combinations capable of predicting the flux reasonably well could predict the feed outlet... [more]

A plate-type Al/Fe−Cr alloy/Al-clad substrate was used to prepare a sandwich-structured plate-type anodic alumina catalyst by anodization, post-modification treatment, and metal loading. The as-prepared plate-type catalyst was utilized in the design of a catalytic plate reactor for a methane steam reforming reaction, and a 3D model was developed to simulate the performance of tube-type and box-type reformers. The experimental results of the preparation of the clad materials showed that the hydrothermal treatment and subsequent high-temperature calcination transformed the amorphous skeletal alumina in the conventional anodic alumina layer into γ-alumina, and significantly increased its specific surface area. Simulation results showed that the temperature difference between the channel wall and the center of the gas phase of the thin-walled catalyst was only 30% of that of the particulate catalyst, indicating the potential advantages of the catalytic plate reactor in terms of heat transf... [more]

This study addresses the use of former gas storage facilities as short-term storage for renewable energy through power-to-gas (PtG) technology in Germany. Three test cases with coupled thermal-hydromechanical (THM) modelling were conducted to evaluate short-term injection and production schedules. The operating rates were controlled by the upper and lower limits of the wellbore pressure. The maximum difference in pore pressure and effective stress was 0.6 MPa in all cases. Fault reactivation analysis was performed on the THM models to estimate fault stability. The critical pore pressure for safe reservoir operation was determined to be 1.25 times the original pore pressure, corresponding to a WBHP value of 20.25 MPa. The upper limit of the gas injection rate for safe storage operation was estimated to be between 100,000 and 150,000 m3/day. The thermal stresses were found to be negligible for short-term cases. The storage capacity of PtG technology was reported to be up to 1,322,400 kWh... [more]

The IEC 61850 standard aims at digitization substations and provides interoperability between various Intelligent Electronic Device vendors. The digitization process is accompanied by several challenges related to data transmission on the ethernet network and the protection behavior under these conditions. Among the challenges, we can mention packet loss, delay, and duplicate frame, which occurs when the merging units (publisher) transmit the sampled values and, for some reason, these packets do not reach the subscriber or are duplicated. Nowadays, most Intelligent Electronic Device manufacturers block the protection function when some sampled value packets are corrupted. The effects of blocking protection when packet loss occurs under normal operating conditions do not cause significant problems. However, when a fault occurs, the corrupted packets can cause a delay in fault clearance, causing even more damage to the grid. The purpose of this article is to present the effects of corrup... [more]

This study analyses the expected utilization of an urban distribution grid under high penetration of photovoltaic and e-mobility with charging infrastructure on a residential level. The grid utilization and the corresponding power flow are evaluated, while varying the control strategies and photovoltaic installed capacity in different scenarios. Four scenarios are used to analyze the impact of e-mobility. The individual mobility demand is modelled based on the largest German studies on mobility “Mobilität in Deutschland”, which is carried out every 5 years. To estimate the ramp-up of photovoltaic generation, a potential analysis of the roof surfaces in the supply area is carried out via an evaluation of an open solar potential study. The photovoltaic feed-in time series is derived individually for each installed system in a resolution of 15 min. The residential consumption is estimated using historical smart meter data, which are collected in London between 2012 and 2014. For a realist... [more]

In the authors’ previous research, a new method for partial discharge detection in the switchgear based on near-field detection was proposed. The content of this paper is the continuation of the authors’ previous research. In order to realize the reasonable layout of the near-field magnetic field probe for partial discharge detection in the switchgear, this paper simulates and analyzes the influence of the internal structure of the switchgear on the near-field propagation characteristics of the electromagnetic wave signal generated by partial discharge, and determines the installation position of the near-field probe in the switchgear. Firstly, the propagation characteristics of electromagnetic wave signals in the different media of the switchgear are analyzed, and the switchgear model is established. Then, based on the finite difference time domain method, the influence of different devices in the switchgear on the near-field propagation of the partial discharge electromagnetic wave s... [more]

Positive displacement pumps produce pressure ripple that can be reduced with the attenuation of the generated flow ripple. This paper presents the application of a gas bladder hydraulic damper with the aim of reducing the oscillations of the delivery flow rate of positive displacement machines. This work is focused on the development of a 1D fluid dynamic model of the damper, which is based on the fundamental fluid motion equations applied for a mono-dimensional flow. In order to represent the fluid flow inside the damper, a particular evaluation of the sound speed has been implemented. Experimental tests have been performed involving an axial piston pump with the damper installed in the delivery pipe to validate the model; tests were carried out at different pump working conditions and with different gas precharge pressure of the damper. The test results confirmed the effectiveness of the device, and the comparison with numerical results demonstrated a good agreement. Simulations have... [more]

The fundamentals of scaling during waterflooding of an oilfield are presented. Mineral precipitation is described using both the kinetics approach, with the corresponding equations given, and the thermodynamic models’ theoretical foundation discussed—mainly specific ion interaction and Pitzer models. This paper focuses on the process of mixing incompatible waters during both water injection and production from an oilfield, as this was identified as a primary reason for barium sulphate precipitation. Two methods of minimizing the risk of solid phase deposition during the mixing of water using the addition of inhibitors and removal of sulfur compounds through a membrane system before water injection into the bed are shown. In addition, formation damage to the near-well zone is discussed with its implications for field operators. Using thermodynamics, especially equations based on the HKF-SRK modified model, this paper describes typical conditions for barium sulphate precipitation during... [more]

The present work considers a 12 MW Solid Oxide Fuel Cell (SOFC) power plant integrated with a heat recovery system installed on board an LNG-fuelled cruise ship of about 175,000 gross tonnes and 345 m in length. The SOFC plant is fed by LNG and generates electrical power within an integrated power system configuration; additionally, it provides part of the thermal energy demand. A zero-dimensional (0D) Aspen Plus model has been built-up to simulate the SOFC power plant and to assess the performances of the proposed heat recovery system. The model has been validated by comparing the results obtained with data from the literature and commercial SOFC modules. The integrated system has been optimized in order to maximize steam production since it is the most requested thermal source on board. The main design outcome is that the steam produced is made by the recovered water from the SOFC exhaust by about 50−60%, thus reducing the onboard water storage or production. Additionally, results in... [more]

Gas turbine fuel burn for an aircraft engine can be obtained analytically using thermodynamic cycle analysis. For large-diameter ultra-high bypass ratio turbofans, the impact of nacelle drag and propulsion system integration must be accounted for in order to obtain realistic estimates of the installed specific fuel consumption. However, simplified models cannot fully represent the complexity of installation effects. In this paper, we present a method that combines thermodynamic cycle analysis with detailed Computational Fluid Dynamics (CFD) modelling of the installation aerodynamics to obtain the fuel consumption at a given mission point. The flow field and propulsive forces arising in a transport aircraft powered by an ultra-high bypass ratio turbofan at cruise are first examined to characterise the operating conditions and measure the sensitivity to variations of the incidence at transonic flight. The proposed methodology, in which dynamic balance of the vehicle is achieved at each i... [more]

He−Xe, with a 40 g/mol molar mass, is considered one of the most promising working media in a space-confined Brayton cycle. The thermodynamic performance of He−Xe in different configuration channels is investigated in this paper to provide a basis for the optimal design of printed circuit board plate heat exchanger (PCHE). In this paper, the factors affecting the temperature distribution of the He−Xe flow field are analyzed based on the flow heat transfer mechanism. It is found that the flow patterns in the logarithmic and outer zones determine the temperature distribution pattern of the flow field. A series of numerical simulations verify the above conclusions, and it is found that reasonable channel structure and operating conditions can significantly improve the thermodynamic performance of the He−Xe flow. Based on the above findings, the Zig channel is optimized, obtaining Sine and Serpentine channels with different structural characteristics. Comprehensive thermodynamic comparison... [more]

This paper presents a low peak-to-average power ratio (PAPR) modulation scheme and demodulation method for low-cost terminals in sixth-generation (6G), which is called one plus delay (1 + D) pi/2(N + 1) BPSK. Explicitly, the modulation scheme is first generated based on pi/2 BPSK, then proceeded by interpolation and (1 + D) transformation. Simulation results show that the proposed (1 + D) pi/2(N + 1) BPSK scheme has lower PAPR and smaller out-of-band leakage in discrete Fourier transform spread orthogonal frequency division multiplexing (DFT-s-OFDM). Moreover, better performance can be attained by increasing the value of N. Finally, similar block error ratio (BLER) performance can be obtained at the same spectral efficiency of the conventional pi/2 BPSK scheme.

The following paper presents an analytical study of the air-gap magnetic field distribution produced by the armature reaction of a linear machine. Based on the method of images, the magnetic field generated by a current carrying conductor inside the air-gap between two smooth infinitely permeable iron surfaces is modeled as a complex 2D function. The conductor model then becomes a current sheet model and horizontally oriented current sheets are used to model the magnetic field produced by the armature reaction for smooth ferromagnetic surfaces. Focus will be given to the study of the slot opening function in front of energized slots in comparison to the not energized ones of the classical theory pointing out some remarkable differences. Later, the model is extended to slotted geometries using a complex slotting function adapted for energized slots. At last, the Maxwell tensor expressed in complex formulation will be integrated to obtain the force components acting on the machine tooth... [more]

The compact, simple, and fast-reaction pneumatic microactuator is significant for the integration and high efficiency of pneumatic systems. In this work, the structure, working principle, and multiphysical model of an on-chip pneumatic microactuator are presented. The on-chip pneumatic microactuator is mainly composed of two parts: a polydimethylsiloxane (PDMS) thin membrane and an actuated chamber. The air pressure in the actuated chamber drives the thin elastic membrane to deformation. Dynamic response mathematical models of the actuated chamber for charging and exhaust with variable volume are established, and the deformation characteristics of the polydimethylsiloxane (PDMS) actuated membrane, the capacity of the actuated chamber, and the valve opening of the on-off membrane microvalve are simulated and analyzed to explore the response characteristics of the proposed pneumatic microactuator. Samples valving analysis of the on-chip membrane microvalve and mixing performance of the m... [more]

The hydrate dissociation is viewed as a phase change process in which hydrates transform from a solid phase into gas and liquid phase at a moving dissociation boundary. The boundary separates the dissociation zone containing gas and water from the undissociated zone containing the hydrates, leading to a density difference. Based on the assumption of a density difference between the dissociation zone and the hydrate zone, the authors propose a mathematical model to study hydrate dissociation under thermal stimulation in an infinite radially symmetrical reservoir. Analytical solutions to the temperature distribution are derived by using the self-similarity transformation. Considering the effect factors of the initial heated-water temperature and hydrate density, the authors conducted a thorough investigation of the temperature distribution and the location of the dissociation front for a sample hydrate reservoir. The results from our model show that the heated-water temperature and hydra... [more]

We propose a mathematical model that allows us to determine the temperature field of a parallel-sided electrically conductive plate element subject to uniform non-stationary electromagnetic action. We formulate initial-boundary value problems to determine the parameters of the non-stationary electromagnetic field (NEMF) and the temperature. We develop a methodology to solve these initial-boundary value problems using the approximation of determining functions by cubic polynomials over thickness of the plate element. General solutions for the related Cauchy problems at uniform non-stationary electromagnetic action are obtained. Based on these solutions, the temporal variation of Joule’s heat and temperature in the plate element, subject to short-term induction heating by an NEMF in the mode of impulse modulating signal (MIMS), is analyzed. Temperature dependencies on the different values of electromagnetic field stress and on the different time duration were obtained. The choice of the... [more]

The existing productivity models of staged fractured horizontal wells in tight oil reservoir are mainly linear flow models based on the idealized dual-medium fracture network structure, which have a certain limitation when applied to the production prediction. Aiming at the difficulty in describing the shape of the complex fractal fracture network, a two-dimensional heterogeneous structure model of the fracture network is proposed in this paper. Considering the deformation characteristics of porous media and the characteristic of non-Darcy fluid flow, a three-zone steady-state productivity model with the combination of radial and linear flow is established. To eliminate strong nonlinear characteristics of the mathematical model, a fractional step method is employed to deduce the production formulas of staged fractured horizontal wells under infinite and finite conductivity fractures. The established productivity model is verified with the actual data of three horizontal wells in differ... [more]

The vertical vibration of a viscoelastic pile immersed in arbitrarily layered soil is investigated by taking the interaction among pile, pile surrounding soil (PSS) and pile end soil (PES) into account. Firstly, considering both the stratification and stress wave effect of soil, a mathematical model of the pile−soil system is established based on the fictitious soil pile (FSP) model. Then, utilizing the impedance function transfer method and Laplace transform technique, the analytical solutions of the vertical dynamic impedance of pile are derived in the frequency domain. The analytical solutions are validated by comparing them with other existing solutions. Finally, a parametric study is put forward to investigate the properties of PES on the vertical dynamic impedance of pile. The results reveal that the properties of PES have a significant effect on the vertical dynamic impedance of pile, but there is a critical influence thickness for this effect. For the cases of the PES thickness... [more]

The influence of mounting motors in wheels’ hubs and flexibility of the twist beam rear suspension on their dynamics and strength is presented in the paper. The international roughness indicator (IRI) is applied to assess the overcoming of road unevenness. This indicator is a combination of a shape of the road unevenness and of overcoming velocity. The movement of a wheel’s axis during obstacles overcoming is described. For the needs of the dynamics analysis, the mathematical model of the rear suspension system with embedded motors is developed using the MSC.Adams-ANSYS interface. The discrete model of the twist beam is prepared in the ANSYS software, which is used in the next step to construct the dynamics model of the rear suspension system using the MSC.Adams program. The vertical components of displacement and acceleration of the wheel’s centre, forces in the suspension’s springs and dampers, as well as forces in the joints are analyzed. The analysis of the suspension beam’s stress... [more]

This paper presents the results of a study on the influence of pressure and temperature of the gas−water medium on the process of hydrocarbon gas hydrate formation occurring at the phase interface. Herein, a mathematical model is proposed to determine the optimum ratios of pressure, gas temperatures, water, and gas bubble sizes in the bubbling, gas ejection, or mixing processes. As a result of our work, we determined that gas hydrate in these processes is formed at the gas−water interface, that is, on the boundary surface of gas bubbles. Moreover, there is a gas temperature range where the hydrate formation rate reaches its maximum. These study findings can be used to optimize various technological processes associated with the production of gas hydrates in the industry.