Capacity markets (CM) are energy markets created to ensure energy supply security. Energy storage devices provide services in the CMs. Li-ion batteries are a popular type of energy storage device used in CMs. The battery lifetime is a key factor in determining the economic viability of Li-ion batteries, and current approaches for estimating this are limited. This paper explores the potential of a lithium-ion battery to provide CM services with four de-rating factors (0.5 h, 1 h, 2 h, and 4 h). During the CM contract, the battery experiences both calendar and cycle degradation, which reduces the overall profit. Physics-based battery and degradation models are used to quantify the degradation costs for batteries in the CM to enhance the previous research results. The degradation model quantifies capacity losses related to the solid−electrolyte interphase (SEI) layer, active material loss, and SEI crack growth. The results show that the physics-based degradation model can accurately predi... [more]

This paper presents a study on the impact of adjacent markets on the electricity market, realizing the advantages of acting in several different markets. The increased use of renewable primary sources to generate electricity and new usages of electricity such as electric mobility are contributing to a better and more rational way of living. The investment in renewable technologies for the distributed generation has been creating new opportunities for owners of such technologies. Besides the selling of electricity and related services (ancillary services) in energy markets, players can participate and negotiate in other markets, such as the carbon/CO2 market, the guarantees of origin market, or provide district heating services selling of steam and hot water among others. These market mechanisms are related to the energy market, originating a wide market strategy improving the benefits of using distributed generators. This paper describes several adjacent markets and how do they complem... [more]

Three Ni-based natural gas steam reforming catalysts, i.e., commercial JM25-4Q and JM57-4Q, and a laboratory-made catalyst (26% Ni on a 5% SiO2−95% Al2O3), are tested in a laboratory reactor, under carbon dioxide methanation and methane steam reforming operating conditions. The laboratory catalyst is more active in both CO2 methanation (equilibrium is reached at 623 K with 100% selectivity) and methane steam reforming (92% hydrogen yield at 890 K) than the two commercial catalysts, likely due to its higher nickel loading. In any case, commercial steam reforming catalysts also show interesting activity in CO2 methanation, reduced by K-doping. The interpretation of the experimental results is supported by a one-dimensional (1D) pseudo-homogeneous packed-bed reactor model, embedding the Xu and Froment local kinetics, with appropriate kinetic parameters for each catalyst. In particular, the H2O adsorption coefficient adopted for the commercial catalysts is about two orders of magnitude hig... [more]

Air quality and energy consumption are among the top ten environmental priorities in seaports as stated by the European Sea Ports Organization. Globally, it is estimated that 15% of energy consumption can be attributed to refrigeration and air conditioning systems in fishing activities. There is a real need to understand energy usage in fishery ports to help identify areas of improvements, with a view to optimize energy usage and minimize carbon emissions. In this study, we elaborate on ways in which a simulation capability can be developed at the community level with a fishery port, using a real-world case study seaport in Milford Heaven (Wales, UK). This simulation-based strategy is used to investigate the potential of renewable energy, including local solar farms, to meet the local power demand. This has informed the development of a simulation-based optimization strategy meant to explore how smart energy communities can be formed at the port level by integrating the smart grid with... [more]

An integrated energy system, referred to specifically as a heterogeneous energy system that combines cooling, heating, power, etc., is a dynamic system containing continuous as well as discrete behaviors on both technical and economic levels. Currently, the comprehensive utilization of multiple forms of energy and the implementation of the energy market have made the simulation of such a system very complicated, which is reflected in two aspects. First, the simulation model becomes complex and varied. Second, the time-varying characteristics of the models are quite diverse. Therefore, a standard and normative modeling and simulation method is urgently needed. This work aims to obtain a compatible modeling and simulation method for the energy economy coupling system. The individual-based model is widely used to describe organisms in an ecology system that are similar to the energy−economy coupled system. Inspired by this, a general simulation approach based on the individual-based model... [more]

This paper presents a compact nonlinear thermal model of pulse transformers. The proposed model takes into account differentiation in values of the temperatures of a ferromagnetic core and each winding. The model is formulated in the form of an electric network realising electrothermal analogy. It consists of current sources representing power dissipated in the core and in each of the windings, capacitors representing thermal capacitances and controlled current sources modelling the influence of dissipated power on the thermal resistances in the proposed model. Both self-heating phenomena in each component of the transformer and mutual thermal couplings between each pair of these components are taken into account. A description of the elaborated model is presented, and the process to estimate the model parameters is proposed. The proposed model was verified experimentally for different transformers. Good agreement between the calculated and measured waveforms of each component temperat... [more]

Improvements in using geothermal sources can be attained through the installation of power plants taking advantage of low and medium enthalpy available in poorly exploited geothermal sites. Geothermal fluids at medium and low temperature could be considered to feed binary cycle power plants using organic fluids for electricity “production” or in cogeneration configuration. The improvement in the use of geothermal aquifers at low-medium enthalpy in small deep sites favours the reduction of drilling well costs, and in addition, it allows the exploitation of local resources in the energy districts. The heat exchanger evaporator enables the thermal heat exchange between the working fluid (which is commonly an organic fluid for an Organic Rankine Cycle) and the geothermal fluid (supplied by the aquifer). Thus, it has to be realised taking into account the thermodynamic proprieties and chemical composition of the geothermal field. The geothermal fluid is typically very aggressive, and it lea... [more]

This work addresses the effect of the total solar reflectance (TSR) value of paints applied in residential buildings upon their thermal performance. A semi-detached residential building was modeled in the ESP-r software, and taken as the basis for parametric studies which assessed the effects of variations in (i) the TSR values; (ii) the thermal characteristics of the building envelope; (iii) the location/climate; and: (iv) the way how the indoor temperature is controlled. The parametric studies were used to find optimal TSR values for each combination of Location + Building envelope characteristics (mainly the existence of thermal insulation). It was concluded that paints having a carefully chosen TSR value lead to better indoor thermal temperatures if the buildings have no mechanical heating or cooling, or to energy savings of up to 32% if they do.

This paper evaluates the liquid water at the gas diffusion layer-channel (GDL-channel) interface of reconstructed GDL microstructures with uniform and non-uniform fiber diameters in wave-like channels. A non-uniform GDL microstructure is reconstructed for the first time at the GDL-channel interface to evaluate droplet motion. The three-layer GDL microstructures are generated using the stochastic technique and implemented using the OpenFOAM computational fluid dynamics (CFD) software (OpenFOAM-6, OpenFOAM Foundation Ltd., London, UK). The present study considers the relationship between reconstructed GDL surfaces with varying fiber diameters, wettability, superficial inlet velocity and droplet size. Results show that the droplet detachment and the average droplet velocity decrease with an increase in the fiber diameter as well as the structural arrangement of the fibers. Under the non-uniform fiber arrangement, the removal rate of water droplets is not significantly improved. However, t... [more]

The existence of an efficient and sufficiently extensive charging infrastructure network appears to be of vital importance for the widespread acceptance of electric mobility by users. The present work aims to develop a tool based on big data analysis that helps to deploy a network of charging stations which can efficiently serve the potential demand, both from the user side, improving the level of service for charging and to cover the territory in a satisfactory way, and from the business side, allowing an analysis of the potential power load. The paper integrates real world traffic data and the results of an experimental campaign on an electric vehicle to evaluate the instantaneous power demand of a fast charging station, based on a procedure for the evaluation and proper time allocation of each charge request.

The aim of the present paper is to investigate the use of the site “Potamon” Dam in the Prefecture of Rethymnon, Crete island, Greece, as a “virtual” renewable electricity supply of a pumped storage plant (PSP) in order to save and exploit the maximum possible part of the rejected wind energy of the autonomous power system of the Crete island. Taking into account the annual time series of the rejected power of the Crete power grid, the present research work targets the optimal configuration of the proposed PSP power station, including the sizing of its individual components as well as the determination of the capacity it could guarantee in order to be economically viable. The rejected electric energy from the actually operating wind farm production, which is not possible to be absorbed by the grid of Crete due to its stable operation limitations, could be absorbed by the here proposed pump storage plant (PSP) and converted to hydraulic energy. This can be achieved by pumping the water... [more]

The aim of this work is the development of a simulation model for the anaerobic digestion process of source-sorted organic fractions of municipal solid wastes. In particular, a detailed model simulating both biological and thermal behaviors of the process was developed. The biological model is based on the Anaerobic Digestion Model 1 (ADM1), which allows one to evaluate the dynamic trends of the concentrations of the main components and the biogas production as a function of the digester operating temperature. The work also includes a detailed thermal model which is developed considering the geometrical and structural features of the digester. The thermal behavior of the digester was also modeled, considering a purposely designed heat exchanger immersed inside the digester. Therefore, the thermal behavior of the process was evaluated by the well-known heat exchange equations and thermal energy balances. The combination of these two models is used to analyze the different possible opera... [more]

This paper presents a new linear state estimation model based on a current summation load flow method for three-phase distribution systems. The developed estimator may be applied to both the supervision of distribution systems under normal operating conditions and the fault location in cases of low and high impedance faults. Our studies were conducted using a real distribution feeder. For fault location analysis, the system was modeled using the ATP (alternative transient program) in order to emulate measurements of voltages and currents at the substation, and voltage magnitudes registered by other meters during the fault. We used the MATLAB™ software to process the algorithms. The main contributions that arose after integrating the current method into system supervision in case of network failures under normal operating conditions and the fault location are as follows: (i) estimation of system losses; (ii) modeling of loads in real time to consider their contributions in the fault loc... [more]

Flow boiling heat transfer in microchannels can provide a high cooling rate, while maintaining a uniform wall temperature, which has been extensively studied as an attractive solution for the thermal management of high-power electronics. The depth-to-width ratio of the microchannel is an important parameter, which not only determines the heat transfer area but also has dominant effect on the heat transfer mechanisms. In the present study, numerical simulations based on the volume of fraction models are performed on the flow boiling in very deep microchannels. The effects of the depth-to-width ratio on the heat transfer coefficient and pressure drop are discussed. The bubble behavior and heat transfer characteristics are analyzed to explain the mechanism of heat transfer enhancement. The results show the very deep microchannels can effectively enhance the heat transfer, lower the temperature rise and show promising applications in the thermal management of high-power electronics.

An appropriate representation of faults is fundamental for hydro-mechanical reservoir models to obtain robust quantitative insights into the spatial distribution of stress, strain and pore pressure. Using a generic model containing a reservoir layer displaced by a fault, we examine three issues which are typically encountered if faults have to be incorporated in reservoir-scale finite element simulations. These are (1) mesh resolution aspects honoring the scale difference between the typical cell size of the finite element (FE) reservoir model and the heterogeneity of a fault zone, (2) grid geometry relative to the fault geometry and (3) fault dip. Different fault representations were implemented and compared regarding those on the modeling results. Remarkable differences in the calculated stress and strain patterns as well as the pore pressure field are observed. The modeling results are used to infer some general recommendations concerning the implementation of faults in hydro-mechan... [more]

Power cable lines are usually buried in the ground. However, in some cases, their ending sections are mounted along the supports of overhead lines. This leads to a situation where the cables are exposed to direct solar radiation and, consequentially, overheat. The paper presents the advanced computer modelling of power cables’ heating, considering their insolation as well as the effect of wind. The temperature and current-carrying capacity of power cables—during exposure to direct solar radiation—are evaluated. An effective method of limiting the unfavourable impact of the sun is discussed. In the presence of solar radiation, the proposed method enables a significant increase in the power cables current-carrying capacity.

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and ce... [more]

Due to the increasing requirements for the reliability of electrical power supply and associated apparatus, it is necessary to provide a detailed analysis of the overvoltage risk of power transformer insulation systems and equipment connected to their terminals. Exposure of transformer windings to overvoltages is the result of the propagation condition of electromagnetic waves in electrical networks and transformer windings. An analysis of transformer winding responses to transients in power systems is of particular importance, especially when protection against surges by typical overvoltage protection systems is applied. The analysis of internal overvoltages in transformers during a typical transient related to switching operations and selected failures is of great importance, particularly to assess the overvoltage exposure of insulation systems in operating conditions. The random nature of overvoltage phenomena in electrical networks implies the usage of computer simulations for the... [more]

To support the interpretation of the experimental results obtained from two laboratory-scale reactors, one working in the steam methane reforming (SMR) mode, and the other in the CO2 hydrogenation (MCO2) mode, a steady-state pseudo-homogeneous 1D non-isothermal packed-bed reactor model is developed, embedding the classical Xu and Froment local kinetics. The laboratory reactors are operated with three different catalysts, two commercial and one homemade. The simulation model makes it possible to identify and account for thermal effects occurring inside the catalytic zone of the reactor and along the exit line. The model is intended to guide the development of small size SMR and MCO2 reactors in the context of Power-to-X (P2X) studies.

The building-integrated wind turbine is a new technology for the utilization of wind energy in cities. Previous studies mainly focused on the wind turbines mounted on the roofs of buildings. This paper discusses the performance of Savonius wind turbines which are mounted on the edges of a high-rise building. A transient CFD method is used to investigate the performance of the turbine and the interaction flows between the turbine and the building. The influence of three main parameters, including the turbine gap, wind angle, and adjacent turbines, are considered. The variations of the turbine torque and power under different operating conditions are evaluated and explained in depth. It is found that the edge-mounted Savonius turbine has a higher coefficient of power than that operating in uniform flows; the average Cp of the turbine under 360-degree wind angles is 92.5% higher than the turbine operating in uniform flows. It is also found that the flow around the building has a great imp... [more]

This study attempts to uncover the most common issue of fuel shortage faced by the oil and transportation industry worldwide. In Pakistan, petroleum is transported to the northern areas from the south coast. Currently, this is done using road tankers as a pipeline is still under construction. However, even after the pipeline becomes operative, road tankers would still be used for intra-city transport. Findings from this study can be used to determine the inter-city transport losses faced by oil companies. This study determines the hydrocarbons lost to the environment during inter-city road transport of petroleum. It takes nearly 2−3 days to complete a one-way trip with the fully loaded tank. Much work has been reported worldwide on hydrocarbon emissions, but nearly all of it has been done either for storage tanks/vessels or fuel tanks in rails/cars. The aim of this study was to investigate the actual amount of fuel lost to the environment due to the sloshing of liquid. Also, the result... [more]

This paper refers to the issue of modelling characteristics of SiC power bipolar junction transistor (BJT), including the self-heating phenomenon. The electrothermal model of the tested device is demonstrated and experimentally verified. The electrical model is based on the isothermal Gummel−Poon model, but several modifications were made including the improved current gain factor (β) model and the modified model of the quasi-saturation region. The accuracy of the presented model was assessed by comparison of measurement and simulation results of selected characteristics of the BT1206-AC SiC BJT manufactured by TranSiC. In this paper, a single device characterization has only been performed. The demonstrated results of research show the evident temperature impact on the transistor d.c. characteristics. A good compliance between the measured and calculated characteristics of the considered transistor is observed even in quasi-saturation mode.

In this paper, a non-contact degradation evaluation method for insulated gate bipolar transistor (IGBT) modules is proposed based on eddy current pulsed thermography approach. In non-contact heat excitation procedures, a high-power induction heater is introduced to generate heat excitation in IGBT modules. The thermographs of the whole temperature mapping are recorded non-invasively by an IR camera. As a result, the joint degradation of IGBT modules can be evaluated by the transient thermal response curves derived from the recorded thermographs. Firstly, the non-destructive evaluation principle of the eddy current pulsed thermography (ECPT) system for an IGBT module with a heat sink is introduced. A 3D simulation module is built with physical parameters in ANSYS simulations, and then thermal propagation behavior considering the degradation impact is investigated. An experimental ECPT system is set up to verify the effectiveness of the proposed method. The experimental results show that... [more]

Harmonic simulations play a key role in studying and predicting the impact of nonlinear devices on the power quality level of distribution grids. A frequency-domain approach allows higher computational efficiency, which has key importance as long as complex networks have to be studied. However, this requires proper frequency-domain behavioral models able to represent the nonlinear voltage−current relationship characterizing these devices. The Frequency Transfer Matrix (FTM) method is one of the most widespread frequency domain modeling approaches for power system applications. However, others suitable techniques have been developed in the last years, in particular the X-parameters approach, which comes from radiofrequency and microwave applications, and the simplified Volterra models under quasi-sinusoidal conditions, that have been specifically tailored for power system devices. In this paper FTM, X-parameters and simplified Volterra approaches are compared in representing the nonline... [more]

The post-closure performance of a generic horizontal drillhole repository for the disposal of spent nuclear fuel (SNF) is quantitatively evaluated using a physics-based numerical model that accounts for coupled thermal-hydrological flow and radionuclide transport processes. The model incorporates most subcomponents of the repository system, from individual waste canisters to the geological far field. The main performance metric is the maximum annual dose to an individual drinking potentially contaminated water taken from a well located above the center of the repository. Safety is evaluated for a wide range of conditions and alternative system evolutions, using deterministic simulations, sensitivity analyses, and a sampling-based uncertainty propagation analysis. These analyses show that the estimated maximum annual dose is low (on the order of 10−4 mSv yr−1, which is 1000 times smaller than a typical dose standard), and that the conclusions drawn from this dose estimate remain valid e... [more]