Alum sludge (AlS) refers to the inevitable by-product generated during the drinking water purification process, where Al-salt is used as a coagulant in the water industry. It has long been treated as “waste”, while landfill is its major final disposal destination. In fact, AlS is an underutilized material with huge potential for beneficial reuse as a raw material in various wastewater treatment processes. In the last two decades, intensive studies have been conducted worldwide to explore the “science” and practical application of AlS. This paper focuses on the recent developments in the use of AlS that show its strong potential for reuse in wastewater treatment processes. In particular, the review covers the key “science” of the nature and mechanisms of AlS, revealing why AlS has the potential to be a value-added material. In addition, the future focus of research towards the widespread application of AlS as a raw material/product in commercial markets is suggested, which expands the s... [more]

The increasing discharge of voluminous non or partially treated wastewaters characterized by complex contaminants poses significant ecological and health risks. Particularly, this practice impacts negatively on socio-economic, technological, industrial, and agricultural development. Therefore, effective control of water pollution is imperative. Over the past decade, membrane filtration has been established as an effective and commercially attractive technology for the separation and purification of water. The performance of membrane-based technologies relies on the intrinsic properties of the membrane barrier itself. As a result, the development of innovative techniques for the preparation of highly efficient membranes has received remarkable attention. Moreover, growing concerns related to cost-effective and greener technologies have induced the need for eco-friendly, renewable, biodegradable, and sustainable source materials for membrane fabrication. Recently, advances in nanotechnol... [more]

Process, manufacturing, and service industries currently face a large number of non-trivial challenges ranging from product conception, going through design, development, commercialization, and delivering in a customized market’s environment. Thus, industries can benefit by integrating new technologies in their day-by-day tasks gaining profitability. This work presents a model for enterprise process development activities called the wide intelligent management architecture model to integrate new technologies for services, processes, and manufacturing companies who strive to find the most efficient way towards enterprise and process intelligence. The model comprises and structures three critical systems: process system, knowledge system, and transactional system. As a result, analytical tools belonging to process activities and transactional data system are guided by a systematic development framework consolidated with formal knowledge models. Thus, the model improves the interaction am... [more]

The problem of metal-induced toxicity is proliferating with an increase in industrialization and urbanization. The buildup of metals results in severe environmental deterioration and harmful impacts on plant growth. In this study, we investigated the potential of two ornamental plants, Catharanthus roseus (L.) G.Don and Celosia argentea L., to tolerate and accumulate Ni, Cr, Cd, Pb, and Cu. These ornamental plants were grown in Hoagland’s nutrient solution containing metal loads (50 µM and 100 µM) alone and in combination with a synthetic chelator, ethylenediaminetetraacetic acid (EDTA) (2.5 mM). Plant growth and metal tolerance varied in both plant species for Ni, Cr, Cd, Pb, and Cu. C. roseus growth was better in treatments without EDTA, particularly in Ni, Cr, and Pb treatments, and Pb content increased in all parts of the plant. In contrast, Cd content decreased with EDTA addition. In C. argentea, the addition of EDTA resulted in improved plant biomass at both doses of Cu. In contr... [more]

Static immersion tests of potential injection pipe steels 42CrMo4, X20Cr13, X46Cr13, X35CrMo4, and X5CrNiCuNb16-4 at T = 60 °C and ambient pressure, as well as p = 100 bar were performed for 700−8000 h in a CO2-saturated synthetic aquifer environment similar to CCS sites in the Northern German Basin (NGB). Corrosion rates at 100 bar are generally lower than at ambient pressure. The main corrosion products are FeCO3 and FeOOH with surface and local corrosion phenomena directly related to the alloy composition and microstructure. The appropriate heat treatment enhances corrosion resistance. The lifetime reduction of X46Cr13, X5CrNiCuNb16-4, and duplex stainless steel X2CrNiMoN22-5-3 in a CCS environment is demonstrated in the in situ corrosion fatigue CF experiments (axial push-pull and rotation bending load, 60 °C, brine: Stuttgart Aquifer and NGB, flowing CO2: 30 L/h, +/− applied potential). Insulating the test setup is necessary to gain reliable data. S-N plots, micrographic-, phase-,... [more]

Porous asphalt pavement (PAP) with a high drainage capacity was modified with powdered activated carbon (PAC) addition to produce permeable reactive pavement (PRP), which may exhibit the potential to reduce environmental non-point source (NPS) pollution. The experimental design mixtures used to produce and test the PRP incorporated with PAC (named PRP-PACs) were conducted as follows: first, the PACs were initially tested to determine their feasibility as an additive in PAP; second, different amounts of PAC were added during the preparation of PAP to produce PRP-PAC, and the unregulated and regulated physical characteristics for the mechanical performance of PRP-PACs were examined to ensure that they meet the regulatory specifications. Third, the aqueous contaminants, namely benzene, toluene, ethyl-benzene, and xylene (BTEX), column adsorption tests were preliminarily conducted to demonstrate their adsorption capacities compared to traditional PAP. The compositions of 0.8% and 1.5% PAC... [more]

Mental health and active aging are two of the main concerns in the 21st century. To search for new neuroprotective compounds, extracts of Codium tomentosum Stackhouse and Fucus vesiculosus L. were obtained through multi-step (four step) subcritical water extraction using a temperature gradient. The safety assessment of the extracts was performed by screening pharmaceutical compounds and pesticides by UHPLC-MS/MS, and iodine and arsenic levels by ICP-MS. Although the extracts were free of pharmaceutical compounds and pesticides, the presence of arsenic and high iodine contents were found in the first two extraction steps. Thus, the health-benefits were only evaluated for the fractions obtained in steps 3 and 4 from the extraction process. These fractions were tested against five brain enzymes implicated in Alzheimer’s, Parkinson’s, and major depression etiology as well as against reactive oxygen and nitrogen species, having been observed a strong enzyme inhibition and radical scavenging... [more]

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: Dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 °C, reaction time of60 min, and concentration of H2SO4 of 20 g/L. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to be 40.24 kJ/mol. Response surface methodology confirmed that all of the experimental parameters had a positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: Dosage of biochar>concentration of H2SO4>reaction temperature >reaction time. This paper provides a versatile strategy for the treatment of wastewater containing Cr (VI) and shows a bright tomorrow for wastewater treatment.

Rare metal minerals are important strategic resources. Promoting the sustainable development of their mining process is not only related to energy and environmental issues, but also directly affects the sustainable development of the entire supply chain. Considering the influence of intergenerational externalities on the equilibrium in the rare metal mineral exploitation process is of critical significance to maintaining the sustainable development of rare metal minerals and securing a sustainable resource exploitation process. This paper develops a sustainability analysis model based on an intergenerational externalities influence and examines the influence of the shift in comprehensive production cost burden through the whole supply chain, which aims at the sustainable development of the exploitation process of rare metal minerals. The results indicate that in a vertically linked industrial chain, the upstream and downstream structure of the supply chain and the type of production co... [more]

Contamination by oil and its derivatives causes serious damage to the environment, motivating the development of innovative technologies for the removal of these contaminants, such as the use of biosurfactants. In the present study, the biosurfactant from Candida tropicalis UCP0996 produced in the low cost-medium formulated with molasses, residual frying oil, and corn steep liquor, was characterized and its toxicity, formulation, and application in removal and biodegradation of oil were investigated. The surface tension of the medium was reduced to 30.4 mN/m, yielding 4.11 g/L of isolated biosurfactant after 120 h. Tests under extreme environmental conditions indicated the stability of the biosurfactant. Chemical characterization by thin layer chromatography (TLC), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (1H NMR), and gas chromatography and mass spectroscopy (CG-MS) revealed the glycolipidic nature of the biosurfactant. The isolated biosurfactant show... [more]

When a wastewater treatment plant (WWTP) uses anaerobic digestion (AD) on its sludge treatment line, the opportunity to install a sidestream deammonification process for the cost-effective removal of the N-rich reject water load generated by the sludge digester should be considered. In this context, the ANITA™ Mox process based on the moving bed biofilm reactor (MBBR) technology has been implemented at more than 30 full-scale facilities over the last 10 years to treat reject water from conventional AD or after thermal hydrolysis process (THP) to reduce the N-load and associated treatment costs on the WWTP. This paper reviews the lessons learned in the implementation of the ANITA™ Mox process at several WWTP in the US, Europe, and Australia.

The growing production of green technologies (such as electric vehicles and systems for renewable electricity production, e.g., wind turbine) is increasing the rare earth element (REE) demands. These metals are considered critical for Europe for their economic relevance and the supply risk. The end-of-life permanent magnets are considered a potential secondary resource of REEs thanks to their content of neodymium (Nd), praseodymium (Pr) or dysprosium (Dy). The scientific literature reports many techniques for permanent magnet recovery. This work used a life cycle assessment (LCA) to identify the most sustainable choice, suggesting the possible improvements to reduce the environmental load. Three different processes are considered: two hydrometallurgical treatments (the first one with HCl and the other one with solid-state chlorination), and a pyrometallurgical technique. The present paper aims to push the stakeholders towards the implementation of sustainable processes for end-of-life... [more]

L. is a traditionally used medicinal plant. With its pronounced antimicrobial potential, this alpine Achillea species may also be used in modern phytotherapy to treat MRSA infections and prevent dermal infections, such as acne vulgaris. For the present study, A. atrata was cultivated in its natural habitat in Switzerland as well as in Germany to elucidate the potential of standardizing plant material derived from this species for pharmaceutical production. Phytochemical characterization of phenolic constituents by HPLC-DAD-MSn revealed that environmental conditions have only a minor impact on the phenolic profile. Metabolic differences between cultivated and wild plants grown in the same environment suggested the possible existence of genetically derived chemotypes. In total, 28 substances were identified, with marked differences in the occurrence of phenolic compounds observed between flowers and leaves. Moreover, to the best of our knowledge, 7 phenolic compounds have been reported f... [more]

Flammable fuel-N2O mixtures raise safety and environmental protection issues in areas where these mixtures are used (such as: industry, research, internal combustion engines). Therefore, it is important to know their laminar combustion velocities and propagation speeds—important safety parameters for design of active protection devices against gas explosions and corresponding safety recommendations. In this paper, the laminar combustion velocities of N2-diluted CH4-N2O flames, obtained in experiments on outwardly propagating flames, at various initial pressures (within 0.5−2.0 bar) and room temperature, are reported. The experiments were made in a 0.5 L spherical cell with central ignition. The laminar combustion velocities were calculated from the constants of cubic law of flame propagation during the early stage of closed cell explosions and the expansion coefficients of unburned flammable mixtures, using the adiabatic model of the flame propagation. The expansion coefficients were d... [more]

Mineral fertilization is considered to be useful for improving soil fertility and yields. However, its use is linked to global warming and soil and water pollution by its rapid mobilization. On the other hand, organic fertilization is recommended to maintain or improve soil organic carbon and total nitrogen stocks while contributing to climate change mitigation. The main goal of this study was to assess the effect of two different fertilizer types, mineral and organic, during three cowpea crop cycles on the soil’s physicochemical properties, enzyme activities, crop yield, crop quality and nutritional composition when considering two cowpea cultivars (Feijão frade de fio preto (FP) and Feijão frade de fio claro (FC)). The use of mineral fertilizers was seen to contribute to improved soil fertility due to the increase in soil properties, such as recalcitrant carbon, total nitrogen, ammonium content, available K and available Mg. On the other hand, organic fertilizers only increased the n... [more]

The unique and outstanding physical and chemical properties of aluminosilicate minerals, including zeolites, make them extremely useful in remediation processes. That is due to their demonstrated high efficiency, inexpensiveness, and environmental friendliness in processes aimed on the elimination of heavy metals from water. The paper reports the results of the examination of selectivity of the tested clay minerals and zeolites toward different heavy metals in light of the postulated sorption mechanisms. It was stated that while the most efficient at concurrent removal of lead and copper from aqueous solutions were synthetic zeolites 3A and 10A, smectite was the best in dealing with prolonged pollution with Pb2+ and Cu2+. Determined as one of the parameters in DKR isotherm energy of the process for each combination of sorbate and sorbent, it showed that the dominant mechanism of adsorption on the tested mineral sorbents was physisorption. The exception was kaolinite, for which that ene... [more]

The phytoremediation role of aquatic plants in situ is extremely important today when, due to repeated droughts and periodical shrinkage of surface water resources, the load of biogenic and toxic substances in these waters is increasing dramatically. The aim of the study was to assess the bioaccumulation of heavy metals (Cd, Cr, Cu, Hg, Mn and Zn) by the Groenlandia densa reintroduced in the area of its historical occurrence in the habitat of rivers characterized by Ranunculion fluitantis vegetation. Research material was collected from 3 sites in the Natura 2000 area in Western Pomerania on areas differing in anthropogenic load, from sites on streams in agricultural, urbanized and forested catchments. The study showed varying content of trace metals in Groenlandia densa. Plants and sediments collected from the site with the highest anthropogenic load, located in an urbanized catchment, contained more metals. The tolerance of Groenlandia densa to elevated Mn levels in water/sediment wa... [more]

Due to its excellent toughness and stiffness in cryogenic conditions, 9% nickel steel is applied to LNG storage facilities, and its usage is increasing as a result of changes in environmental regulations. A study was conducted on the development of a predictive model to optimize the laser welding process of 9% nickel steel, and two prediction models were developed using one hundred data points obtained through experiments. A global regression model used as a general prediction model and a modified regression model using the p-value of the analysis of variance were developed, and their prediction performance was compared. It was found that the modified regression model was superior to the global regression model in terms of predicting the bead shape, including parameters such as penetration depth, bead height, and area ratio.

Carotenoids are important phytochemicals contributing nutritional health benefits in the human diet, with a significant contribution from cereals as one of the major food component around the world. Different methods have been described and adopted for the extraction and isolation of carotenoid compounds. Saponification can be seen as an option for carotenoid extraction from cereals as it converts retinol esters to retinol and removes other abundant compounds such as triglycerides. Extraction of carotenoids content of locally adapted and organic cereals have been limitedly investigated and was, therefore, evaluated in the present study, with a specific aim to understand genotypic and local cultivation effects and interactions. Therefore, 17 diverse cereal genotypes of local origin were grown organically in four localities and evaluated for carotenoid content and composition by HPLC. The results showed a large variation in content and composition of carotenoids in locally adapted and or... [more]

The laccase enzyme was successfully immobilized over a magnetic amino-functionalized metal−organic framework Fe3O4-NH2@MIL-101(Cr). Different techniques were used for the characterization of the synthesized materials. The Fe3O4-NH2@MIL-101(Cr) laccase showed excellent resistance to high temperatures and low pH levels with a high immobilization capacity and large activity recovery, due to the combination of covalent binding and adsorption advantages. The long-term storage of immobilized laccase for 28 days indicated a retention of 88% of its initial activity, due to the high stability of the immobilized system. Furthermore, a residual activity of 49% was observed at 85 °C. The immobilized laccase was effectively used for the biodegradation of Reactive Black 5 (RB) and Alizarin Red S (AR) dyes in water. The factors affecting the RB and AR degradation using the immobilized laccase (dye concentration, temperature and pH) were investigated to determine the optimum treatment conditions. The... [more]

Plastic production has been increasing at enormous rates. Particularly, the socioenvironmental problems resulting from the linear economy model have been widely discussed, especially regarding plastic pieces intended for single use and disposed improperly in the environment. Nonetheless, greenhouse gas emissions caused by inappropriate disposal or recycling and by the many production stages have not been discussed thoroughly. Regarding the manufacturing processes, carbon dioxide is produced mainly through heating of process streams and intrinsic chemical transformations, explaining why first-generation petrochemical industries are among the top five most greenhouse gas (GHG)-polluting businesses. Consequently, the plastics market must pursue full integration with the circular economy approach, promoting the simultaneous recycling of plastic wastes and sequestration and reuse of CO2 through carbon capture and utilization (CCU) strategies, which can be employed for the manufacture of ole... [more]

Pressure-driven processes have come a long way since they were introduced. These processes, namely Ultra-Filtration (UF), Nano-Filtration (NF), and Reverse-Osmosis (RO), aim to enhance the efficiency of wastewater treatment, thereby aiming at a cleaner production. Membranes may be polymeric, ceramic, metallic, or organo-mineral, and the filtration techniques differ in pore size from dense to porous membrane. The applied pressure varies according to the method used. These are being utilized in many exciting applications in, for example, the food industry, the pharmaceutical industry, and wastewater treatment. This paper attempts to comprehensively review the principle behind the different pressure-driven membrane technologies and their use in the removal of heavy metals from wastewater. The transport mechanism has been elaborated, which helps in the predictive modeling of the membrane system. Fouling of the membrane is perhaps the only barrier to the emergence of membrane technology and... [more]

The rapid increasing number of automobile products has brought great convenience to people’s living, but it has also caused serious environmental issues, waste of resources and energy shortage during its whole lifecycle. Corporate Environmental Responsibility (CER) refers to the company’s responsibility to avoid damage to the natural environment derived from its corporate social responsibility (CSR), and it plays an important role in solving resource and environmental problems. However, due to various internal and external reasons, it is difficult for the automobile manufacturing industry to find the key drivers for the implementation of CER. This research proposes a model framework that uses the fuzzy decision-making test and evaluation laboratory (fuzzy DEMATEL) method to analyze the drivers of CER from the perspective of the triple bottom line (TBL) of economy, environment and society. Firstly, the common drivers of CER are collected using literature review and questionnaire survey... [more]

New observations of non-indigenous species (NIS) in coastal waters, such as the Gulf of Cadiz (Spain) have increased since 1980 and more or less exponentially in the last five years. Ballast water has become the most significant pathway for unintentional introductions of NIS into marine ecosystems. For example, the marine larvae of crustacean decapods that inhabit the water column could be transported in ballast water. Although elevated concentrations of metals are toxic to many marine organisms, some of them have evolved effective detoxification, or avoidance mechanisms making it possible to consider they have a superior ability to withstand exposures to these toxicants. In this text, we try to reinforce the hypothesis that anthropogenic modifications (such as chemical alterations and modified environments) benefit NIS with broad environmental tolerances. Taking these risks into account, a reinforcement of efficient Ballast Water Management Systems to respond to today’s challenging en... [more]

Ponding system or land application techniques are widely used at industrial scale to treat palm oil mill effluent (POME) prior to discharge to the environment. POME is considered as one of the major problems that has generated voluminously from the palm oil industries. The main purpose of this article is to organize the scattered available information on various aspects and a wide range of promising current POME treatments including biological microorganisms, physicochemical methods of coagulation, and membrane and thermochemical process. In addition, the integrated system of anaerobic-aerobic bioreactor (IAAB), which has been touted as highly efficient with easy control at acceptable temperature range and shorter treatment time, has potential to be exploited for POME treatment. The main influencing factors for IAAB POME treatment are highlighted as outstanding characteristics for challenges and future prospects.