This paper focuses on a detailed numerical investigation combined with experimental research for a non-premixed swirl combustor, which aims to analyze the effects of the blade angle of the outer swirler and equivalence ratio on flow and combustion characteristics. In the experiment, the temperature in the furnace was obtained with a thermocouple, while a realizable k-ε turbulence model and two-step reaction mechanism of methane and air are used in the numerical method. The calculation results are in good agreement with the experimental data. The results reveal that the air flow rate through the swirler accounts for a small amount of the total air due to the influence of the draft fan, and there is no central recirculation zone (CRZ) despite the presence of the swirler. It was also found that NO emissions gradually decrease as the blade angle of the outer swirler increases. It was also indicated that the average temperature is 100 K higher than the general combustor with a 58° blade ang... [more]

In order to achieve Australia’s greenhouse gas emissions reduction targets, a majority of the existing residential building stock in Australia will require retrofitting in favour of energy-efficient solutions. This paper considers retrofitting for conditioning to be one of the most straightforward and offers the greatest potential to deliver significant comfort and energy-saving results. Radiant conditioning systems are not new, yet some game-changing innovations have taken place over the last decade that may require an entire paradigm shift in the manner we condition our buildings. The reiteration of the principle ‘thermally active systems’ suggests that our buildings need to accommodate these systems into the fabric of building components. However, extremely few products and/or innovative solutions for doing such seem to be provided by the industry. We seem incompetent with solutions that are not costing the Earth, insulating, lightweight, and offering an instant response time to con... [more]

Climate change and environmental pollution are considered to be among the main challenges faced by the modern world. The growth of environmental awareness and the adoption of a pro-environmental approach are considered to be the key megatrends with the greatest impact on the global economy in the upcoming years. According to Eurobarometer, EU citizens are particularly aware of the importance of protecting the environment. Although the negative environmental impact of European industry has improved over the past decades, EU citizens believe that there is further scope in terms of helping companies transition towards adopting more sustainable models. One of the factors contributing to the reduction in negative environmental impact is the participation of enterprises in voluntary programs such as the Environmental Management System (EMS), according to ISO 14001, or the Eco-management and Audit Scheme (EMAS). The whole population of Polish companies registered under the EMAS was included i... [more]

The performance of the air-cooler in refrigeration systems plays a key role in their energy efficiency. Here, the plenum-chamber coefficient was defined to investigate a possible way of enhancing the refrigeration coefficient that reflects the efficiency of the system. To investigate the influence of the plenum-chamber coefficient on the frosting and the cooling system of the air-cooler, three plenum-chamber coefficients (0.74, 0.97, 1.2) were studied under two different relative humidities. The temperature decreasing curve of the environmental chamber, the velocity distribution of the air-cooler, and the frost accumulation under and on the air-cooler were analyzed. We find that the homogeneity of the velocity distribution of the air-cooler and the frost accumulation increase with a growing plenum-chamber coefficient, while the frost accumulation on the fin will first increase and then decrease with the increase in the plenum-chamber coefficient. In general, frosting is more present wh... [more]

Solid circulation rate (Gs) represents the mass flux of circulating particles in circulating fluidized bed (CFB) systems and is a significant parameter for the design and operation of CFB reactors. Many measuring technologies for Gs have been proposed, though few of them can be applied in industrial units. This paper presents a comprehensive study on measuring technologies, and the results indicate that though the accumulation method is most widely applied, it is constrained by the disturbance of normal particle circulation. Some publications have proposed mathematic models based on pressure drop or other parameters to establish Gs measurement models; these necessitate the accurate modeling of complicated gas-solid flows in industrial devices. Methods based on certain measurement devices to specify parameters like velocity require device endurance in the industrial operation environment and stable local gas-solid flow. The Gs measuring technologies are strongly influenced by local gas-... [more]

The aim of the study is to draw attention to the fact that reducing methane and nitrous oxide emissions as a result of traditional manure storage for several months in a pile is not only a non-ecological solution, but also unprofitable. A solution that combines both aspects—environmental and financial—is the use of manure as a substrate for a biogas plant, but immediately—directly after its removal from the dairy barn. As part of the case study, the energy and economic balance of a model farm with dairy farming for the scenario without biogas plant and with a biogas plant using manure as the main substrate in methane fermentation processes was also performed. Research data on the average emission of ammonia and nitrous oxide from 1 Mg of stored manure as well as the results of laboratory tests on the yield of biogas from dairy cows manure were obtained on the basis of samples taken from the farm being a case study. The use of a biogas installation would allow the emission of carbon dio... [more]

Because of rapid urbanization, traffic problems, and other factors, underground spaces have been used more in the twenty-first century. Large underground spaces are required for underground city, metro, tunnel, mine, industrial and agricultural engineering, and civil air defense engineering. Underground spaces with varying thermal, ventilation, and lighting environments can face problems of comfort, health, and safety. High temperatures, high humidity, difficulty in flue gas emission, harmful microorganisms, radon, and physical and psychological problems are examples of issues. Air quality control technologies for underground spaces, such as ventilation, dehumidification, natural energy utilization, smoke extraction, and ventilation resistance reduction, are discussed. Ventilation for smoke-proofing/evacuation is also extensively addressed.

European Union Member States are called upon to meet internationally proposed environmental goals. This study is based, in particular, on the recommendation of the European Union (EU), which encourages Member States to pursue effective policies to reduce greenhouse gas (GHGs) emissions, including through appropriate changes in the behavioral habits of citizens. In this respect, among the main sectors involved, transport and mobility should certainly be mentioned. National institutions should be adequately involved in order to achieve the objectives set; in this regard, universities must certainly be considered for their educational value. These latter, for instance, could commit to improving the environmental performance of the mobility of their commuter students (to a not insignificant extent), since commuting modes are often the cause of high CO2 emissions; indeed, they still largely involve the use of internal combustion engines based on fossil fuels. In this paper, the effectivenes... [more]

Municipal waste management in the EU has been challenged to a thorough transformation towards a Circular Economy. It is addressed by a number of quantitative policy targets, including a restriction on municipal waste landfilling to 10% in 2035. This paper presents the data on municipal waste composition in a large Polish city, based on thorough waste sorting analyses. On average, 374 kg of municipal waste is collected per capita in Wroclaw, of which 41% are separately collected fractions. The approach to implement the EU recycling targets until 2035 is presented, including an increase of sorting and recycling efficiency and a significant share of recyclables being retrieved from the residual waste fraction. Notwithstanding the recycling targets, an important stream of residual waste remains, amounting to 200 k ton in 2020 and approx. 130 k ton in 2035, which is available for energy recovery. The respective LHV values range from 8.5 to 7.6 MJ/kg. The results indicate that the residual w... [more]

The mining industry plays an extremely important strategic role in China’s economic and social development. In the new era of pursuing circular/green/efficient development, the evaluation of the total factor environmental efficiency (TFEE) of China’s mining industry is essential for alleviating resource waste and environmental pollution. The Epsilon-Based Measure (EBM) model effectively solves the shortcomings of radial and non-radial DEA models. In addition, the Malmquist−Luenberger (ML) index can measure the dynamic change of efficiency value. Combining the EBM model and the ML productivity index, this paper evaluates the TFEE from the static and dynamic perspective in China’s 31 provincial mining industries over the period 2007−2016. The Theil index is employed to reveal the root of the overall provincial TFEE gap (OGTFEE) in China’s mining industry. The results show that the average total factor static environmental efficiency (TFSEE) of China’s provincial mining industry exhibits... [more]

Wellbore instability resulting from deep mudstone hydration severely restricts the development of oil and gas resources from deep reservoir in western China. Accurate evaluation of drilling fluid inhibition properties plays an important role in selecting drilling fluid that can control deep mudstone hydration and then sustain wellbore stability. The previous evaluations are conducted by qualitative analysis and cannot consider the influence of complex hydration conditions of deep mudstone (high temperature, high pressure and flushing action). The study proposes a quantitative method to evaluate drilling fluid’s inhibition property for deep mudstone under natural drilling conditions. In this method, the cohesive strength of mudstone after hydration is adopted as the inhibition index of the tested drilling fluid. An experimental platform containing a newly designed HPHT (High pressure and high temperature) hydration experiment apparatus and mechanics characterization of mudstone after hy... [more]

This paper reviews the major researchers of liquid, immersion, and two-phase cooling. Currently, liquids are used instead of air to cool the growing data centers. Immersion cooling shows a higher heat transfer coefficient than conventional cooling (<37 W/cm2). Because the use of liquids with high global warming potentials is prohibited, the number of liquids that can be used is limited. This paper discusses the existing, relevant literature from researchers who have studied the issue at least thrice. The authors were divided into those who focused on the surface and those who formed a structure on the surface. In summary, the authors suggested the following research directions: The experimental conditions of porous foam are not diverse, and there is a concern about the separation of foam and coating into the tub. The experimental conditions of the immersion tub should also be varied according to the heat and pressure over time. Structure-level research shows higher performance than... [more]

Universal access to energy is a global challenge for sustainable development that requires granting last-mile access to energy services to rural and isolated communities. However, achieving access is not sufficient: it must be done affordably, reliably and with an adequate quality. Universal access to energy goes beyond the mere selection of a technical solution or infrastructure; it demands being able to design management models for projects aiming to guarantee that households may access energy services in a sustainable way. This study analyzes the main elements (i.e., governance, technological and business models) of management models in universal access to energy projects and their impact on the different dimensions of sustainability (i.e., social, environmental, and economic). The study then presents three case studies of rural electrification projects having different configurations of the management model, with special focus on the differences in the business model, and it analyz... [more]

Modern theories that make up the paradigm of sustainable development, and the best practices derived from them, are based on the consistency of individual and public needs, factors of economic growth and ecosystem conservation [...]

Energy consumption in residential, commercial and industrial buildings is one of the major contributors to global warming. Due to the increase in the latter, and growing global energy crisis, more attention is being paid to renewable energy resources (RES). The use of innovative concepts in existing buildings is gaining popularity to provide reduction in energy requirements for electricity, heating and cooling. In this paper, an electricity, heating and cooling cooperation mechanism among neighboring buildings with RES is proposed. It relies on adjusting the RES tariff with a mutual agreement between the neighboring buildings, with an aim to minimize the operational costs. For this purpose, a mathematical model is developed for joint energy cooperation, where surplus energy in one of the buildings is shared with others, thereby reducing dependency on the grid. The optimization structure of the environment friendly energy cooperation is nonlinear, which is linearized using the McCormick... [more]

This paper presents the results of testing the electrical strength of an insulating system in a vacuum obtained from three noble gases: argon, neon, helium, and air. The breakdown voltages were measured for contact gaps of 1 mm and 2 mm. A difference was observed in the pressure range where the electrical strength was kept constant. The chamber filled with helium residual gases lost its insulating properties at the highest pressure among the tested gases (2.00 × 100 Pa at contact gap d = 2 mm), while the chamber filled with argon gas lost its insulating properties at the lowest pressure among the tested gases (2.00 × 10−1 Pa at contact gap d = 2 mm). After a decrease in electrical strength, an intense glow discharge was observed. A theoretical description related to the initiation of an electrical breakdown in vacuum insulating systems is also presented. The situation in which the discharge chamber with a contact system was filled with the mentioned gases was analyzed. The mean free pa... [more]

Hydropower depends on the elevation head and water flow of a river. However, other factors must be considered, such as the risk associated with surface processes and environmental factors. The study aims to analyze a landscape’s dynamics and locate potential sites for small-scale hydropower systems (<10 MW) using a geographic information system, the curve number method, and the TopoToolbox with a digital elevation model and available spatial datasets. Across Bohol Island in the central Philippines, the study found 94 potential sites with hydraulic heads ranging from 20−62.4 m, river discharges between 0.02 to 9.71 m3/s, and a total hydropower capacity of 13.595 MW. The river profile analysis classified the sites to five levels of risk to geo-hazards, with three-fourths of the sites being at ‘high’ to ‘very high’ risk levels while more than 50% of the total power can be generated in ‘low’ risk areas. Land-use and population constraints reduced the sites to 25 and the hydropower capac... [more]

E-waste and end-of-life vehicles (ELVs) are fast-growing waste streams in the EU and beyond that require specific collection and treatment activities to avoid environmental pollution and resource depletion fed by the linear economy model. This paper aims to investigate the links between e-waste and ELVs streams and the circular economy approach of the EU. Romania is examined as a relevant case study for the central and eastern European Region regarding: (i) the current e-waste and ELVs management deficiencies and challenges in line with circular economy principles promoted by EU; (ii) analysis of E-waste and ELVs flows data; and (iii) best circular economy initiatives related to e-waste and ELVs in Romania, including the opportunity to create new jobs in treatment activities that the simple operations from the first stages of e-waste recycling can produce locally and regionally in Romania. This work points out the current knowledge gaps and future research directions for these special... [more]

The Austrian Education Energy Initiative ETSIT has been established as a response to the EU Energy Efficiency Directive and the Austrian Energy Efficiency Act. This paper investigates the energy literacy of its young participants, i.e., 6000 primary and secondary school students altogether, on a cognitive, affective and behavioural level, and it compares the putative energy-saving effectiveness of the workshops to that of conventional energy audits.For the current analysis, data from, 640 students who validly answered an online survey shortly after participating in one of the energy education workshops, and 353 students who validly answered the online survey approximately one year after having participated (overall n = 993) were analysed. The results indicate that ETSIT raises students’ energy literacy on a cognitive, affective and behavioural level with about three-quarters of participants claiming they will positively change their energy consumption behaviour in the future as a resul... [more]

One of the most crucial factors for energy transition and the incorporation of renewable energy sources into the existing energy map is citizen engagement. Local energy communities (LECs), which are cooperative-based coalitions aimed at reducing the carbon footprint of the residential building sector, have received increasing attention in the past decade. This is because residential buildings account for almost half of the total energy consumed worldwide. A resounding 75% of it is used for thermal energy consumption, heating and cooling, cooking and bathing. However, the main focus of the literature worldwide is explicitly on electrical LECs, despite the fact that the significant increase in natural gas and oil prices, creates instability in the heating and cooling prices. The scope of this study is to provide an overview of the research field regarding Thermal LECs, using both a thorough literature review as well as bibliometric analysis (VOSviewer software), in order to validate the... [more]

The potential of bio-electro-jet fuel (BEJF) production with integration into an existing biomass-based combined heat and power (CHP) facility was investigated. The BEJF is produced via Fischer−Tropsch (F−T) synthesis from biogenic CO2 and H2 obtained by water electrolysis. Techno-economic (TEA)- and life. cycle (LCA)- assessments were performed to evaluate the production cost and environmental impact of the BEJF production route. The BEJF mass fraction reached 40% of the total F−T crude produced. A reduction of 78% in heating demands was achieved through energy integration, leading to an increase in the thermal efficiency by up to 39%, based on the F−T crude. The total production cost of BEJF was in the range of EUR 1.6−2.5/liter (EUR 169−250/MWh). The GWP of the BEJF was estimated to be 19 g CO2-eq per MJ BEJF. The reduction potential in GWP in contrast to the fossil jet baseline fuel varied from 44% to more than 86%. The findings of this study underline the potential of BEJF as a re... [more]

This paper demonstrates the investigation of the acquired outcomes from consistent information observing a 467.2 kWp solar photovoltaic (SPV) framework commissioned on the roofs of three separate high-rise buildings, which are located at the location of 26.9585° N and 80.9992° E. Onside real-time performance for this system was investigated for three years, 2018−2020; this system contains 1460 SPV panels of 320 Wp each, having 20 PV panels per string, 09 DC/AC power conditioning units (PCU), and a SCADA (supervisory control and data acquisition) system for monitoring the other necessary parts of a grid-interactive SPV system. The outcomes of the different buildings are compared with each other to analyze the power output at the same input conditions. Hardware components of the plants with approximately the same ratings (P2 ~ 108.8 kWp + P3 ~ 128 kWp) are compared (with P1 ~ 230.4 kWp). Simulation modeling of the year 2020 in PVsyst tool for generated energy, Performance Ratio (PR), and... [more]

In light of the increasing demand for energy sources in the world and the need to meet climate goals set by countries, there is growing global interest in high temperature gas cooled reactors (HTGRs), especially as they are known to be inherently safe nuclear reactors. The safety of HTGRs results, among other, from the nature of the nuclear fuel used in them in the form of coated TRISO particles (tri-structural-isotropic) and the reduction of the total amount of radioactive waste generated. This paper reviews numerous methods used to ensure the sustainable, feasible management and long-term storage of HTGR nuclear waste for the protection of the environment and society. The types of waste generated in the HTGR cycle are presented as well as the methods of their characterization, which are important for long-time storage and final disposal. Two leading nuclear fuel cycle strategies, the once-through cycle (direct disposal or open cycle) and the twice-through cycle (recycling or partiall... [more]

To achieve sustainable development goals (SDGs), it is necessary to solve the problem of assessing and measuring energy sustainability performance. A popular indicator used for this purpose is the World Energy Council (WEC) energy sustainability index, or the Energy Trilemma Index, which is based on such key metrics as energy security, energy equity, environmental sustainability, and country context. Each of the four metrics, or dimensions, includes many indicators that depend on both internal and external factors. By combining a variety of indicators into integral ones, WEC ranks countries in terms of energy sustainability. However, what is not taken into account is how countries differ in terms of economic development, income, energy mix, renewables use, ownership in the energy sector, and other factors, and neither is the methodology itself disclosed by the developers. As a provider for all other sectors of the economy, the energy sector plays an important role in developing countri... [more]

It is vitally important that a transmission network provides a continuity of electricity to end users and that the transmission system operator prioritizes its safety and reliability. This article presents the possibilities of using multi-track overhead lines with varying levels of rated voltage, run on a common support structure. This solution would ensure safe operation of the system, reduce the area used for the construction of new overhead lines, and, at the same time increase the transmission network capacity. This article focuses on the method of modeling overhead lines for the analysis of electromagnetic transient states that occur during non-simultaneous disturbance phenomena. This article presents the idea of multi-circuit, multi-voltage lines and their validity of use in power systems. An analysis of electromagnetic transient states for non-simultaneous disturbances in multi-path, multi-voltage lines is presented. This analysis has been made on the basis of a network model, u... [more]