This article addresses the problem of estimating the potential economic and environmental gains for utility grids of shifting the electric-vehicle (EV) charging time and location. The current literature on shifting EV charging loads has been limited by real-world data availability and has typically therefore relied on simulated studies. Collaborating with a large automobile company and a major utility grid operator in California, this research used actual EV operational data and grid-operation data including locational marginal prices, marginal-grid-emission-rate data, and renewable-energy-generation ratio information. With assumptions about the future potential availability of EV charging stations, this research estimated the maximum potential gains in the economic and environmental performance of the electrical-grid operation by optimizing the time and location of EV charging. For the problem of rescheduling the charging sessions, the optimization models and objective functions were... [more]

Many countries, especially China, have extensively promoted liquefied natural gas (LNG) to replace diesel in heavy-duty vehicles for to achieve sustainable transport aims, including carbon peaks and neutrality. We developed a life-cycle calculation model for environmental load differences covering vehicle and fuel cycles to comprehensively compare the LNG tractor-trailer and its diesel counterpart in China on a full suite of environmental impacts. We found that the LNG tractor-trailer consumes less aluminum but more iron and energy; emits less nitrogen oxide, sulfur oxide, nonmethane volatile organic compounds, and particulate matter but more greenhouse gases (GHG) and carbon monoxide (CO); and causes less abiotic depletion potential, acidification potential, and human toxicity potential impacts but more global warming potential (GWP) and photooxidant creation potential (POCP) impacts. Poor fuel economy was found to largely drive the higher life-cycle GHG and CO emissions and GWP and P... [more]

The area of degraded sites in the world is constantly expanding and has been a serious environmental problem for years. Such terrains are not only polluted, but also due to erosion, devoid of plant cover and organic matter. The degradation trends can be reversed by supporting remediation/reclamation processes. One of the possibilities is the introduction of biodegradable waste/biowaste substrates into the soil. The additives can be the waste itself or preformed substrates, such composts, mineral-organic fertilizers or biochar. In EU countries average value of compost used for land restoration and landfill cover was equal 4.9%. The transformation of waste in valuable products require the fulfillment of a number of conditions (waste quality, process conditions, law, local circumstances). Application on degraded land surface bio-based waste substrates has several advantages: increase soil organic matter (SOM) and nutrient content, biodiversity and activity of microbial soil communities an... [more]

The continuous operation and the specialized conditions needed for safely delivering healthcare services make hospitals among the most expensive buildings. Several studies in different countries have investigated the potential role and contribution of macroscopic indices of hospitals in total energy requirements. In this work, we tried to investigate the energy requirements of Greek hospitals in terms of cost. We collected data from all public hospitals in Greece over a 2 year period (2018−2019) and evaluated the contribution of various factors in the total energy cost. The data revealed large variability by region and by hospital, even regarding structures of the same category and size. The analysis also showed that structural and operational data of each hospital differently influence the hospitals’ energy requirements. Using regression methods, we developed two models for calculating annual energy costs. One only contains hospital structural data (number of beds, type of hospital, n... [more]

The main aim of this article was to test the authors’ proprietary method (i.e., the conversion method applied to evaluate e-banking services that support sustainable development goals in households, communities, and society). The authors’ conversion method can be applied with the aim of maintaining a balance between households, producers, and public administration services in line with the principles of sustainable development of the information society in Poland. To achieve this goal, the authors identified the differences between the results obtained using the conversion method and the results produced by other methods such as TOPSIS, Promethee II, and PROSA involving the same group of respondents. A hypothesis was made about the existence of significant differences in the results obtained as part of the studies. The research was carried out on a sample of nearly 830 ratings concerning the 27 most popular electronic banks in Poland. As part of the survey, the respondents assessed 18... [more]

This article presents the impact of climate change on air treatment processes and energy demand in a selected air-conditioning system. The analysis was performed for a system supplying rooms with pre-treated primary air. Further treatment occurred directly in the rooms with individual devices such as fan coils or chilled beams. The analysis of the second stage of air treatment was not part of this study. The calculations were made for the city of Warsaw, where, according to the climate analysis for the period 1961−2020, an increase in outside temperature by 0.4 °C per decade and an increase in air humidity by 0.2 g/kg per decade were observed. The system analysis was divided into two stages. The first, including calculations made for monthly average climate data for the entire period of 1961−2020, shows changes in the energy demand of the system, resulting from progressive climate change. This analysis confirmed the general tendency of increasing demand for cooling energy and decreasin... [more]

One of the currently promoted methods of counteracting climate change is nature-based climate solutions, which harness the power of nature to reduce greenhouse gas emissions. Sustainable management of ecosystems is a guarantee for sustained human well-being. This underestimated, but extremely efficient and cheap method of integrating nature resources into the urban fabric is an economic “injection” for communal authorities. These “green” benefits should be standard in land-use planning in the era of anthropocentrism. Solutions based on nature were the reason for investigating their perception by Polish municipalities. The survey covered the entire country (all 2477 municipalities) from 20 July to 31 August 2021 through an electronic survey, obtaining 2128 responses (85.9% return rate). In the final result, data were obtained that support the hypotheses posed in the study. The main objective of the research was to check the level of activity of municipalities in Poland in the field of p... [more]

The suitability of sewage-sludge derived washing agents (SS_WAs) (dissolved organic matter DOM; humic-like substances HLS; soluble humic substances SHS), was assessed for removing Cd from highly contaminated (300 mg/kg) sandy clay loam and clay. The soils were remediated via column flushing at two flow rates, 0.5 and 1.0 mL/min. The stability of the flow velocity (FV) depended on the type of SS_WA and decreased in the following order: DOM > HLS > SHS. Cd was most effectively removed during the first hours of flushing, and the process proceeded with a first-order kinetics. The overall process efficiency was higher at flow rate of 1.0 mL/min than at 0.5 mL/min and ranged from 65.7 (SHS) to 75.5% (DOM) for the sandy clay loam and from 64.7% (SHS) to 67.8% (DOM) for the clay. However, all SS_WAs at both flow rates removed the most mobile Cd fraction (F1) with an efficiency above 90%. Flushing improved soil characteristics in terms of the content of organic matter, humic substances and nutr... [more]

This article deals with options for how to express the luminous flux from outdoor electrical substations of the electric transmission system. Processing of the models of light emissions before and after refurbishment of lighting systems was motivated by setting out rules for the design and erection of refurbished lighting systems in outdoor electrical substations, which are most commonly built in inhabited rural areas with low luminance of the background. The proposed model and calculations are based on requirements of international standards and recommendations for lighting of outdoor workplaces as well as on internal regulations of the ČEPS (Czech Transmission System Operator). These requirements are implemented in real electrical substations and lighting models that are extended by the calculation space of the software goniophotometer. The software goniophotometer was used to evaluate light distribution characteristics of entire electric stations in various situations. This article... [more]

Quantifying the wider benefits of energy efficient building retrofits is crucial to incentivise householder retrofit investments. This research recognises the value of key performance indicators (KPIs) for assessing and demonstrating retrofitting benefits and provides an assessment of KPIs for evaluating retrofits. An integrated framework for evaluating retrofits using a set of economic, social, and environmental KPIs is proposed. This KPI framework is then applied in a pre- and post-retrofit assessment of five case study dwellings located in Ireland, revealing its usefulness in demonstrating the wider benefits of retrofitting to householders, with a view to driving retrofit investment. Three of these case study dwellings had state-of-the-art retrofit technologies installed as part of the works, including heat pumps and solar PV systems. In addition to demonstrating the wider benefits of retrofitting, the framework allowed for the identification of potential causes for differences in p... [more]

Mechanical systems (as belt conveyors) used in the mining industry, especially in deep underground mines, must be supervised on a regular basis. Unfortunately, they require high power and are spatially distributed over a large area. Till now, some elements of the conveyor (drive units) have been monitored 24 h/day using SCADA systems. The rest of the conveyor is inspected by maintenance staff. To minimize the presence of humans in harsh environments, we propose a mobile inspection platform based on autonomous UGV. It is equipped with various sensors, and in practice it is capable of collecting almost the same information as maintenance inspectors (RGB image, sound, gas sensor, etc.). Till now such experiments have been performed in the lab or in the mine, but the robot was controlled by the operator. In such a scenario the robot is able to record data, process them and detect, for example, an overheated idler. In this paper we will introduce the general concept of an automatic robot-ba... [more]

The unbridled use of fossil fuels is a serious problem that has become increasingly evident over the years. As such fuels contribute considerably to environmental pollution, there is a need to find new, sustainable sources of energy with low emissions of greenhouse gases. Climate change poses a substantial challenge for the scientific community. Thus, the use of renewable energy through technologies that offer maximum efficiency with minimal pollution and carbon emissions has become a major goal. Technology related to the use of hydrogen as a fuel is one of the most promising solutions for future systems of clean energy. The aim of the present review was to provide an overview of elements related to the potential use of hydrogen as an alternative energy source, considering its specific chemical and physical characteristics as well as prospects for an increase in the participation of hydrogen fuel in the world energy matrix.

The site where a peaceful underground nuclear explosion, Crystal, was detonated in 1974, at a depth of 98 m in perennially frozen Cambrian limestones, was studied by electrical resistivity tomography (ERT) in 2019. The purpose of our research, the results of which are presented in this article, was to assess the current permafrost state at the Crystal site and its surroundings by inversion and interpretation of electrical resistivity tomography (ERT) data. Inversion of the ERT data in Res2Dinv verified against ZondRes2D forward models yielded 2D inverted resistivity sections to a depth of 80 m. The ERT images revealed locally degrading permafrost at the Crystal site and its surroundings. The warming effect was caused by two main factors: (i) a damage zone of deformed rocks permeable to heat and fluids, with a radius of 160 m around the emplacement hole; (ii) the removal of natural land cover at the site in 2006. The artificial cover of rock from a nearby quarry, which was put up above... [more]

The process of consumption modernization can be expressed by adopting the principles of sustainable development within the sphere of consumption. It should be emphasized that the implementation of a sustainable consumption model becomes especially important when considering the fact that not only various types of enterprises but also consumers participate in the excessive consumption of natural resources. The processes of sustainable consumption that are related to its humanization and the formation of a responsible society are a response to the overconsumption of goods and services, which is not determined by actual human needs and does not consider social and ecological costs. The aim of the paper is to present a process of consumption modernization in Poland in the context of the functioning of the renewable energy market. Special attention is paid to behaviours that are consistent with the sustainable consumption model, as well as with the motives for using renewable energy sources... [more]

Existing studies of financing efficiency concentrate on capital structure and a single external environment or internal management characteristic. Few of the studies include the internal and external financing environments at the same time for hydrogen energy industry financing efficiency. This paper used the data envelopment analysis (DEA) model and the Malmquist index to measure the financing efficiency of 70 hydrogen energy listed enterprises in China from 2014 to 2020 from both static and dynamic perspectives. Then, a tobit model was constructed to explore the influence of external environment and internal factors on the financing efficiency. The contributions of this paper are studying the internal and external financing environments, and integrating financing cost efficiency and capital allocation efficiency into the financing efficiency of hydrogen energy enterprises. The results show that, firstly, the financing efficiency of China’s hydrogen energy listed enterprises showed an... [more]

The aim of the article is to examine technological innovations developed by engineers as part of Project-Based Learning at one of the Polish technical universities. We examined whether the innovations being developed meet the goals of sustainable development and whether they provide the basis for the introduction of sustainable business models. We analyzed reports from 49 projects implemented in the years 2018−2020 in which 146 scientists, 282 students of the Silesian University of Technology, and 126 experts from the university’s business environment were involved. We performed the analysis using content analysis and visualization techniques. The results show that the studied innovations implement the goals of sustainable development and most of them may become the basis of sustainable business models. The most frequently pursued goals are Industry, Innovation, and Infrastructure and Good Health and Well-Being. Most of the studied innovations can become the basis of the archetype of a... [more]

The target for 2030 of reaching a 32% share of renewable energy in the gross final energy consumption can be achieved by speeding up the transformation pending the implementation of knowledge transfer (KT) policies that foster regional cooperation for the cost-effective development of renewables. The research purpose is the analysis of important factors in the development of the renewable energy sector through knowledge sharing and collaboration across the Member States in a comparable manner. The hypotheses are as follows: Hypothesis 1 (H1) there are synergies between knowledge transfer and economic impact through income and jobs for the renewable energy sector and Hypothesis 2 (H2) the EU countries have different profiles of synergy. The research proposition was established through the employment of a quantitative synergy and trade-offs analysis based on the knowledge transfer indicators and the sustainable development framework. The research method, namely the advanced sustainabilit... [more]

The effects of urban transport are highly concerning. The rapid urbanization and motorization in smart cities have a huge impact on sustainability. The goal of the paper is to analyse the smart cities selected, in terms of the urban transport. This paper presents an overview of research works published between 1991 and 2020 concerning urban transport and MCDM (multi-criteria decision making). The author highlights the importance of decision-making criteria and their weight, as well as techniques. Seven criteria and forty-four objects were used as the input of the approach. The entropy weight method was used to compute the weight of each criterion. The TOPSIS (Technique for Order Performance by Similarity to Ideal Solution) was applied to calculate the assessment and ranking of transport performance for each smart city. Portland was found to be the best location for transport enterprises and projects; Tbilisi was ranked last. The values of the relative closeness coefficient ranged from... [more]

The Scheffler type concentrator is a curved metal reflector particularly suitable for solar thermal systems with a receiver fixed to the ground. Its operating principle is to deform the reflector throughout the year to optimize its performance in collecting sunlight. This study analyses the optical performance of a Scheffler reflector during the year. A CAD software tool is utilized to reproduce the mechanical deformations of a real Scheffler concentrator and the shape of the light spot on the receiver is analyzed by means of raytracing simulations. The starting configuration is the equinoctial paraboloid, which produces a point-like spot on the two equinox days only. On all other days of the year, this paraboloid is deformed in a suitable way in order to keep the spot as small as possible, but, even so, it is no longer a point-like spot. In the present work the simulated light distributions on the receiver, generated by the paraboloids (deformed or original), are compared. The results... [more]

Severe wellbore stability issues were reported while drilling in laminated formation with weak planes such as beddings. To accurately determine the safe mud weight according to the changing environment is of primary importance for safety control of drilling. Considering both the elastic and strength anisotropy of bedding formation, a novel theoretical model is established and the stress and failure around wellbores are analyzed. The accuracy and applicability of the theoretical model is verified by in situ field data. For the purpose of fulfilling real-time prediction, the method flowchart of programming is also provided. The results show that the model built can be conveniently used to predict the stress distribution, failure area, and collapse and fracture pressure while drilling, and rather good predictions can be made compared to real field data. In addition, the inhomogeneity of in situ stress and elastic parameters affect the upper limit of the safe mud weight window (SMWW) great... [more]

This article presents a solution that strengthens information security in critical infrastructure entities. Critical infrastructure plays a key role in the functioning of the state and the life of its citizens. Therefore, the protection of critical infrastructure is one of priorities in Poland. The aim of this article is to show that designated postal operators may become an important link in the process of information flow and cybersecurity. Based on their multiple-year experience and expended competences, the operators may provide digital services for entities responsible for the energy security infrastructure. Verification of this goal is necessary, since critical infrastructure is exposed to growing threats, both in the area of energy and other sensitive sectors of the economy. Research results presented in the article were obtained by conducting a CATI survey. The study used the purposeful selection method, which allows to influence the structure of a sample in the context of goal... [more]

Owing to the recent increase in the number of warning reports and alerts on the dangers of fine dusts, there has been an increasing concern over fine dusts among citizens. In spaces with poor ventilation, the occupants are forced to open the window to initiate natural ventilation via the direct introduction of the outside air; however, this may pose a serious challenge if the external fine-dust concentration is high. The lack of natural ventilation increases the indoor carbon dioxide (CO2) concentration, thus necessitating the installation of mechanical ventilation systems. This study analyzed the frequency of the application of mechanical ventilation systems in the Multi-purpose activity space of elementary schools, which are spaces where children require a higher indoor air quality than adults owing to the rapid increase in the CO2 concentration of the Multi-purpose activity space during activities. In addition, the architectural and equipment factors of the Multi-purpose activity sp... [more]

We examine the critical pore radius that results in critical gas saturation during pure methane hydrate dissociation within geologic porous media. Critical gas saturation is defined as the fraction of gas volume inside a pore system when the methane gas phase spans the system. Analytical solutions for the critical pore radii are obtained for two, simple pore systems consisting of either a single pore-body or a single pore-body connected with a number of pore-throats. Further, we obtain critical values for pore sizes above which the production of methane gas is possible. Results shown in the current study correspond to the case when the depression of the dissociation temperature (due to the presence of small-sized pores; namely, with a pore radius of less than 100 nm) is considered. The temperature shift due to confinement in porous media is estimated through the well-known Gibbs-Thompson equation. The particular results are of interest to geological media and particularly in the methan... [more]

Circular economy implementations tend to decrease the human pressure on the environment, but not all produce footprint reductions. That observation brings the need for tools for the evaluation of recycling processes. Based on the Exergy Footprint concept, the presented work formulates a procedure for its application to industrial chemical recycling processes. It illustrates its application in the example of cotton waste recycling. This includes the evaluation of the entire process chain of polyethylene synthesis by recycling cotton waste. The chemical recycling stages are identified and used to construct the entire flowsheet that eliminates the cotton waste and its footprints at the expense of additional exergy input. The exergy performance of the process is evaluated. The identified exergy assets and liabilities are 138 MJ/kg ethylene and 153 MJ/kg ethylene, reducing the Exergy Footprint by 75% and the greenhouse gas footprint by 43% compared to the linear pattern of polyethylene prod... [more]

Mountain huts are stand-alone micro-grid systems that are not connected to a power grid. However, they impact the environment by generating electricity and through day-to-day operations. The installed generator needs to be flexible to cover fluctuations in the energy demand. Replacing fossil fuels with renewable energy sources presents a challenge when it comes to balancing electricity generation and consumption. This paper presents an integration-and-optimization process for renewable energy sources in a mountain hut’s electricity generation system combined with a lifecycle assessment. A custom computational model was developed, validated with experimental data and integrated into a TRNSYS model. Five different electricity generation topologies were modelled to find the best configuration that matches the dynamics and meets the cumulative electricity demand. A lifecycle assessment methodology was used to evaluate the environmental impacts of all the topologies for one typical operatin... [more]