The present article analyzes the technological advancement and innovations related to drilling operations. It covers the review of currently proven and emerging technologies that could mitigate the drilling operational deficiencies and instabilities that could hinder operational performance activities and the economic part of drilling development with great effort to minimize their environmental footprint. Drilling system design and operations are among the major aspects and cost-effective endeavors of the oil and gas industries, which are therefore technology dependent. They are also considered to be among the most expensive operations in the world, as they require huge expenses daily. Drilling success, depending on prevalent conditions, is a function of several general factors. These include the selection of the best technologies and tools, procedural optimization, concrete problem-solving, accurate prediction, and rapid decision-making. Consequently, any sorts of tools or advanced t... [more]

This study focuses on the valorization of the organic fraction of municipal solid waste (biopulp) by hydrothermal liquefaction. Thereby, homogeneous alkali catalysts (KOH, NaOH, K2CO3, and Na2CO3) and a residual aqueous phase recirculation methodology were mutually employed to enhance the bio-crude yield and energy efficiency of a sub-critical hydrothermal conversion (350 °C, 15−20 Mpa, 15 min). Interestingly, single recirculation of the concentrated aqueous phase positively increased the bio-crude yield in all cases, while the higher heating value (HHV) of the bio-crudes slightly dropped. Compared to the non-catalytic experiment, K2CO3 and Na2CO3 effectively increased the bio-crude yield by 14 and 7.3%, respectively. However, KOH and NaOH showed a negative variation in the bio-crude yield. The highest bio-crude yield (37.5 wt.%) and energy recovery (ER) (59.4%) were achieved when K2CO3 and concentrated aqueous phase recirculation were simultaneously applied to the process. The inorgan... [more]

The article aims to identify the latest trends in research on renewable energy, sustainability and the environment. A total of 92,873 publications from 123 Scopus sources for 2020−2021 are compared using the scoping review method. The results show that the most cited works in this sample are those by authors from the Asian region. The research of these authors focuses on the security, efficiency and reliability of separate elements in energy systems. Besides, the paper considers the problems regarding COVID disease along with the renewable energy sources, perovskite and organic solar panels, nanostructured materials and high energy density. Finally, the paper analyses applications of computer science methods in research on renewable energy, sustainability and the environment. The findings evidently show that recent advancements in computer science methods were not extensively used in the discussed research domain and give a great room for novel strategies of prognosing, simulation and... [more]

Increasing energy demand in buildings with a 40% global share and 30% greenhouse gas emissions has accounted for climate change and a consequent crisis encouraging improvement of building energy efficiency to achieve the combined benefit of energy, economy, and environment. For an efficient system, the optimization of different design control strategies such as building space load, occupancy, lighting, and HVAC becomes inevitable. Therefore, interdisciplinary teamwork of developers, designers, architects, and consumers to deliver a high-performance building becomes essential. This review aims to endorse the importance of Building Performance Simulation in the pre-design phase along with the challenges faced during its adaptation to implementation. A morphology chart is structured to showcase the improvement in Building Energy Efficiency by implementing Building Performance Simulation for different building energy systems and by implementing various energy efficiency strategies to achie... [more]

The article presents the course of the evolution of the concept of urban renewal’s emergence into its current, mature, integrated form of sustainable regeneration (sustainable urban regeneration—SUR). We present how the determination of renewal areas and its goals began to be based on particular indicators, and how the importance of these analyses gradually increased in managing the implementation of urban regeneration programs. Analytical techniques using GIS were used in the analyses of the differentiation of crisis phenomena inside cities before they became popular in smart city tools. Despite the wide use of GIS to analyze the diversity of crisis phenomena within the city, the availability of data means that different spheres are characterized with different accuracy. Starting from the significance of individual spheres, the focus has primarily been on the environment, which is underappreciated in Poland. Municipalities (urban, rural, urban−rural) with regeneration programs do not... [more]

This research presents the energy, exergy, economic, and environmental assessment, and multi-objective optimization of a flash-binary geothermal CCHP cycle. A sensitivity analysis of production well inlet temperature and cooling to power flow ratio on exergetic, economic, and environmental parameters was conducted. Furthermore, the effects of the inflation rate and plant working hours on economic parameters were investigated. Results showed that increasing the production well inlet temperature harms exergy efficiency and exergetic performance criteria and results in a gain in exergo-environmental impact index and heating capacity. In addition, the total plant cost increased by raising the production well temperature. Furthermore, increasing the cooling to power flow ratio caused a reduction in exergy efficiency, exergetic performance criteria, and produced net power and an enhancement in exergy destruction, cooling capacity, and total plant cost. The exergy efficiency and total cost ra... [more]

Seawater represents a potential resource to ensure sustainable availability of water for population and irrigation purposes, especially in some areas of the world. Desalination processes allow the production of fresh water, but they generate also brine as waste product. Sustainable brine management should be identified to ensure proper disposal and potentially resource recovery. This experimental study showed that emerging technologies such as Microbial Desalination Cells (MDCs) may provide a valuable contribution to the sustainability of the seawater desalination sector. In this paper, we report results on lab-scale desalination brine treatments applying MDCs, which allow energy savings, resource recovery, environmental impact minimization, and reduction of the organic load in municipal wastewater. Our results showed that MDCs’ treatment allows the removal of approximately 33 g of salts (62% of the total)—including chlorides, bromides, and sulphates—from 20 mL of brine within 96 h. Th... [more]

The purpose of this study is to identify the most relevant renewable energy technologies for buildings and to assess the effectiveness of their implementation in the long term for Kuwait. Methods of analogies and comparisons were used to determine the features of energy efficiency based on the technologies under study. The study proposes the methodological approach to assessing the effectiveness of the introduction of renewable energy technologies, determining the direction of increasing the energy efficiency of buildings and the investment efficiency of introducing these technologies. Renewable energy efficiency analysis for buildings in Kuwait confirms that solar energy systems have been the most widely available for widespread use of solar energy over the past three years. An increasing level of energy efficiency with a decrease in the notional cost of increasing energy savings is characteristic of solar collectors with booster reflectors. The proposed model for assessing the level... [more]

Efficient air-cooling systems for hot climatic conditions, such as Southern Europe, are required in the context of nearly Zero Energy Buildings, nZEB. Innovative air-cooling systems such as regenerative indirect evaporative coolers, RIEC and desiccant regenerative indirect evaporative coolers, DRIEC, can be considered an interesting alternative to direct expansion air-cooling systems, DX. The main aim of the present work was to evaluate the seasonal performance of three air-cooling systems in terms of air quality, thermal comfort and energy consumption in a standard classroom. Several annual energy simulations were carried out to evaluate these indexes for four different climate zones in the Mediterranean area. The simulations were carried out with empirically validated models. The results showed that DRIEC and DX improved by 29.8% and 14.6% over RIEC regarding thermal comfort, for the warmest climatic conditions, Lampedusa and Seville. However, DX showed an energy consumption three an... [more]

An increasing number of data sources and models to handle them call for transparency and openness in assessing their goodness and practical use for people [...]

This paper presents a techno-economic assessment of hydrokinetic energy of Cozumel Island, where ocean currents have been detected, but tourist activities are paramount. The main objective of this research is to identify devices that have been used to harvest hydrokinetic power elsewhere and perform an economic analysis as to their implementation in the Mexican Caribbean. First, the energy potential of the area was evaluated using simulated data available through the HYCOM consortium. Then, for four pre-commercial and commercial turbines, technical and economic analyses of their deployments were performed. Socio-environmental constraints were reviewed and discussed. Three optimal sites were identified, with an average annual hydrokinetic energy density of 3−6 MWh/m2-year. These sites meet the socio-environmental requirements for marine kinetic energy harvesting. Of the turbines considered in the analysis, the best energy price/cost ratio is that of SeaGen device, with a maximum theoret... [more]

This study aims to design a 16.4 MW photovoltaic solar system located in the Brazilian Northeast and quantify the associated greenhouse gas emissions and environmental payback. The energy system was designed to minimize the Levelized Cost of Energy. The greenhouse gas emissions were quantified with the Life Cycle Assessment methodology, expressing the environmental impact in terms of generated energy (kg CO2-eq/kWh) and following ISO 14040 and 14044. The environmental payback considered the Brazilian electricity mix and degradation of the panels. The results indicated a system capable of producing 521,443 MWh in 25 years, with an emission factor of 0.044 kg CO2-eq/kWh and environmental payback of five years and eight months. The emission factor is at least ten times lower than thermoelectric natural gas power plants. The solar panels were the main contributors to the greenhouse gas emissions, representing 90.59% of overall emissions. It is concluded that photovoltaic energy systems are... [more]

Solid fuel combustion in a chamber does not necessarily occur at a constant rate and may show fluctuations due to variables such as varying burning rates, chamber pressure, and residual combustion. These variables can cause the fuel to burn disproportionately. The acoustic environment of obstacle vortex-driven flow due to transient combustion with pressure oscillations in a solid fuel chamber is numerically investigated in the present study. Solid fuel combustion is considered transient, and flow characteristics of the present problem are governed by large eddies shed from an obstacle. Since unsteady Reynolds-averaged Navier-Stokes (URANS) simulations are not appropriate to compute the present flow phenomenon, therefore, a detached eddy simulation (DES) is performed to precisely predict the flow behavior. Simulation of steady-state combustion is carried out to validate the numerical results with available experimental data from the literature. The simulation of transient combustion sho... [more]

The waste management sector is transitioning from a dirty and undesirable industry towards a green and sustainable future where energy and materials are recycled. Recycling has potential in sewage sludge treatment, where energy and highly valuable nutrients can be recovered through innovative and sustainable sludge management. Although there are many technologies and techniques already used for sewage sludge, the indicators for their sustainability are not developed. In terms of sustainable and innovative sewage sludge treatment, usually, only techno-economic aspects of existing and current technologies are considered. We explore the existing indicators and propose new indicators for sustainable and innovative sewage sludge treatment technologies. The indicators are differentiated into four main categories: technical, social, environmental and economic, where specific indicators are explained, followed by a description of their impact on sustainability. We also consider a case study us... [more]

The increase in the world population leads to the generation of high amounts of wastewater and the requirement for more energy to satisfy the population’s needs [...]

The increase in energy demand requires urgent investments in sustainable energy. It is vital to the success of the 2030 Agenda, adopted by the United Nations General Assembly. The article aimed to assess the situation of the European Union countries with regard to energy use. Indicators related to the implementation of SDG7 and environmental and resource productivity of the economy were adopted for the study. The research presented in this article fits into contemporary debates on the effectiveness of implementing one of the SDG7: ensuring access to affordable, reliable, sustainable, and modern energy for all. The analysis included 26 countries that have been in the European Union since 2010. The study’s originality lies in the use of primary data obtained from the Eurostat database for three research periods: 2010, 2015, and 2020, which will allow for assessing the situation of the surveyed EU countries in the area of energy use. In order to achieve the research objective, selected me... [more]

Now that many countries have set goals for reaching net zero emissions by the middle of the century, it is important to clarify the role of each country in achieving the 1.5 °C target of the Paris Agreement. Here, we evaluated China’s role by calculating the global temperature impacts caused by China’s emission pathways available in global emissions scenarios toward the 1.5 °C target. Our results show that China’s contribution to global warming in 2050 (since 2005) is 0.17 °C on average, with a range of 0.1 °C to 0.22 °C. The peak contributions of China vary from 0.1 °C to 0.23 °C, with the years reached distributing between 2036 and 2065. The large difference in peak temperatures arises from the differences in emission pathways of carbon dioxide (CO2), methane (CH4), and sulfur dioxide (SO2). We further analyzed the effect of the different mix of CO2 and CH4 mitigation trajectories in China’s pathways on the global mean temperature. We found that China’s near-term CH4 mitigation reduc... [more]

Due to the global warming and resulting problems, attention has been paid to greenhouse gases released into the atmosphere since the 1980s and 1990s. For this reason, the Montreal Protocol and the Kyoto Protocol have tightened regulations on the use of gaseous refrigerants in both HVAC systems and industrial refrigeration. Gradually, new generations of gaseous refrigerants, that theoretically have much less negative environmental impact than their predecessors, are introduced into the market. The key parameter describing environmental impact is the GWP index, which is most often defined on a time horizon of 100 years. The long-term use of new generations of gaseous refrigerants in HVAC systems reduces CO2 emissions into the atmosphere; however, given that new generation gases often have a short lifetime, it seems that the adopted assessment may not be applicable. The aim of the article was to show how emissions of CO2 equivalent to the atmosphere differs in the short and long time hori... [more]

Applications of the Internet of Things (IoT) are rapidly utilized in smart buildings and smart cities to reduce energy consumption. This advancement has caused a knowledge gap in applying IoT effectively by experts in the built environment to achieve energy efficiency. The study aims to provide an extensive review of IoT applications for energy savings in buildings and cities. This study contributes to the field of IoT by guiding and supporting built environment experts to utilize IoT technologies. This paper performed a thorough study using a systematic review that covered an overview of IoT concepts, models, applications, trends and challenges that can be encountered in the built environment. The findings indicated limitations in developing IoT strategies in buildings and cities by professionals in this field due to insufficient comprehension of technologies and their applied methods. Additionally, the study found an indefinite implementation and constraints on using IoT when integra... [more]

Presently, the world is undergoing exciting haste to install photovoltaic (PV) systems in industry, residential/commercial buildings, transportation, deserts, street lights, and many other applications. Solar photovoltaic energy systems are clean and reliable energy sources that are unlimited, unlike their fossil fuel counterparts. The energy market is rapidly growing globally with newly and cumulative installed capacities of about 37.6 GW and 139.6 GW, accounting for 53% and 55%, respectively, in 2017, making it one of the fastest-growing industries. The cumulative photovoltaic installations are projected to have reached 600 GW worldwide and are projected to reach 4500 GW by 2050 because of the strategies and policies of many countries. In 2021, more than three-quarters of the developed countries are now home to one solar installation. This article evaluates a critical and extensive review of the contributions of solar photovoltaic systems to national development. The approach follows... [more]

The architectural and construction professions are in a state of major transition [...]

Submarine permafrost is widely distributed in polar ocean, which has an important impact on polar engineering and subsea energy exploitation. According to the frozen porous medium theory, an analytical solution of the one-dimensional vertically dynamic response of the submarine permafrost is derived by using the Laplace transform and the separation variable method. Using the general forms of partial differential equations and the pressure acoustics module in COMSOL software, a finite element model of submarine permafrost overlying a seawater layer is established. The results show that the degraded solution agrees well with the existing results of the vertically dynamic response of the saturated soil layer in the seabed, and the analytical and numerical solutions are in good agreement. The water depth, saturation and temperature have important effects on the dynamic responses of submarine permafrost. When the soil layer is fully saturated, the water depth has a weak effect on resonance... [more]

Due to the significance of environmental aspects, the modeling of hybrid systems should be performed with the lowest cost and environmental pollution. Therefore, an effective and optimum sizing method can ensure acceptable performance. This paper implements a “technique for order performance by similarity to the ideal solution” (TOPSIS) method combined with the “analytic hierarchy process (AHP)” method to size a standalone system based on techno-economic parameters. For this reason, a survey was conducted to collect local load data on Monpura Island, located in Bhola, Bangladesh. Visible and design faults of the existing PV/diesel mini-grid have also been identified. Five alternative hybrid configurations have been considered as to evaluate the best optimum system. Two economic and one environmental criterion was used to size the system. Two experts specialized in energy systems evaluated the criteria and proposed the suitable system. Battery, wind and PV capital cost multipliers have... [more]

Energy poverty, defined as a lack of access to reliable electricity and reliance on traditional biomass resources for cooking, affects over a billion people daily. The World Health Organization estimates that household air pollution from inefficient stoves causes more premature deaths than malaria, tuberculosis, and HIV/AIDS. Increasing demand for energy has led to dramatic increases in emissions. The need for reliable electricity and limiting emissions drives research on Resilient Hybrid Energy Systems (RHESs), which provide cleaner energy through combining wind, solar, and biomass energy with traditional fossil energy, increasing production efficiency and reliability and reducing generating costs and emissions. Microgrids have been shown as an efficient means of implementing RHESs, with some focused mainly on reducing the environmental impact of electric power generation. The technical challenges of designing, implementing, and applying microgrids involve conducting a cradle-to-grave... [more]

(1) The use of renewable energy for power and heat supply is one of the strategies to reduce greenhouse gas emissions. As only 14% of German households are supplied with renewable energy, a shift is necessary. This shift should be realized with the lowest possible environmental impact. This paper assesses the environmental impacts of changes in energy generation and distribution, by integrating the life cycle assessment (LCA) method into energy system models (ESM). (2) The integrated LCA is applied to a case study of the German neighborhood of Herne, (i) to optimize the energy supply, considering different technologies, and (ii) to determine the environmental impacts of the base case (status quo), a cost-optimized scenario, and a CO2-optimized scenario. (3) The use of gas boilers in the base case is substituted with CHPs, surface water heat pumps and PV-systems in the CO2-optimized scenario, and five ground-coupled heat pumps and PV-systems for the cost-optimized scenario. This technol... [more]