The increase in global energy demand has led to increased research in harvesting solar energy. Solar energy is widely used in homes, electric vehicles and is a great solution to power remote areas. DC−DC converters are essential in extracting power from solar panels. One of the main problems in designing converters for solar energy applications is boosting the low output voltage of the solar panel to meaningful levels. While there are several topologies to achieve high gain, some of the problems faced by them are the extreme duty ratio, complex design and discontinuous input current. This paper presents a novel topology that uses an interleaved input, a voltage lift capacitor and a hybrid switched capacitor network to achieve high gain without an extreme duty ratio or bulky magnetics. The proposed converter is controlled using a microcontroller which regulates the output voltage. The voltage lift capacitor and the switched capacitor network enhances the voltage gain over a conventional... [more]

We extend the widely-studied Heterogeneous Autoregressive Realized Volatility (HAR-RV) model to examine the out-of-sample forecasting value of climate-risk factors for the realized volatility of movements of the prices of crude oil, heating oil, and natural gas. The climate-risk factors have been constructed in recent literature using techniques of computational linguistics, and consist of daily proxies of physical (natural disasters and global warming) and transition (U.S. climate policy and international summits) risks involving the climate. We find that climate-risk factors contribute to out-of-sample forecasting performance mainly at a monthly and, in some cases, also at a weekly forecast horizon. We demonstrate that our main finding is robust to various modifications of our forecasting experiment, and to using three different popular shrinkage estimators to estimate the extended HAR-RV model. We also study longer forecast horizons of up to three months, and we account for the poss... [more]

CO2 sequestration in coal is mainly attributed to adsorption. The adsorption experiments of CO2 were conducted at injection pressures ranging from 1 to 3 MPa on coal samples with five kinds of particle sizes. The fitting degree of four classical adsorption models to experimental adsorption data was systematically compared. The adsorption properties of CO2 were comprehensively discussed. The temperature changes of coal samples at different positions during CO2 adsorption were measured by using the improved adsorption tank, and then the energy conversion law was obtained. The results showed increasing gas injection pressure can effectively increase the adsorption capacity of CO2 on coal samples. The BET equation had the best fitting accuracy for CO2 adsorption on various size coal samples. There was a significant exothermic effect during CO2 adsorption and storage. With the rise of injection pressure, the peak value of the rising temperature of coal samples increased, but the change rate... [more]

Concentrated animal feeding operations (both slaughter and dairy cattle) lead to land, water, and air pollution if waste storage and handling systems are not effectively managed. At the same time, cattle biomass (CB), which includes both slaughter/feedlot biomass (FB) and dairy biomass (DB), have the potential to be a source of green energy at coal-fired power plants. Part I presented results on NOx reductions with pure FB or Coal: FB blends as reburn fuels. Part II deals with results from reburning with pure DB or Coal: DB blends as reburn fuels. A mixture of NG with a small amount of NH3 was used to generate the baseline NOx of 400−420 ppm (or 185−194 g/GJ). NOx emissions were found to be reduced by as much as 96% when reburning with FB. The effects of reburn fuel type, equivalence ratio (ERRBZ) in the reburn zone, vitiated air, several injection configurations of reburn fuel and initial NO concentrations on NOx emissions were investigated. The ERRBZ shows a significant effect on the... [more]

The article provides an overview and comparative analysis of various types of batteries, including the most modern type—lithium-ion batteries. Currently, lithium-ion batteries (LIB) are widely used in electrical complexes and systems, including as a traction battery for electric vehicles. Increasing the service life of the storage devices used today is an important scientific and technical problem due to their rapid wear and tear and high cost. This article discusses the main approaches and methods for researching the LIB resource. First of all, a detailed analysis of the causes of degradation was carried out and the processes occurring in lithium-ion batteries during charging, discharging, resting and difficult operating conditions were established. Then, the main factors influencing the service life are determined: charging and discharging currents, self-discharge current, temperature, number of cycles, discharge depth, operating range of charge level, etc. when simulating a real mot... [more]

The process of slow pyrolysis of seven nut shell samples, in a nitrogen-purged atmosphere, has been studied, as well as characteristics of biochar obtained. The heat carrier with a temperature of 400−600 °C (with a step of 100 °C) was supplied indirectly using a double-walled reactor. The heating rate was 60 °C/min. At increased temperature of the heating medium, a decrease in the amount of the resulting carbon residue averaged 6.2 wt%. The release of non-condensable combustible gas-phase compounds CO, CH4, and H2, with maximum concentrations of 12.7, 14.0, and 0.7 vol%, respectively, was registered. The features of the obtained biochar sample conversions were studied using thermal analysis in inert (nitrogen) and oxidative (air) mediums at 10 °C/min heating rate. Kinetic analysis was performed using Coats−Redfern method. Thermal analysis showed that the main weight loss (Δm = 32.8−43.0 wt%) occurs at temperatures ranging between 290 °C and 400 °C, which is due to cellulose decompositi... [more]

In recent years, several attempts have been made to promote renewable energy in the residential sector to help reducing its CO2 emissions. Among existing approaches utilizing substances capable of directly storing and transporting thermal energy has recently become a point of interest. Zeolite 13X with exceptional capacity to safely store thermal energy for long periods and release heat due to its unique molecular structure is known to be one of the best options serving this purpose. However, the application of this ceramic as a heat storage material in the residential sector is associated with significant challenges dictated by the limitations of the sector, such as space restrictions and affordability. The current review attempts to explore the extent of these challenges, mainly related to design and efficiency from different perspectives. The main aim here is to provide a clear vision for a better understanding of the state of the art of this technology and to help to identify possi... [more]

Conventional fossil-fuel-based power systems are undergoing rapid transformation via the replacement of coal-fired generation with wind and solar farms. The stochastic and intermittent nature of such renewable sources demands alternative dispatchable technology capable of meeting system stability and reliability needs. Battery energy storage can play a crucial role in enabling the high uptake of wind and solar generation. However, battery life is very sensitive to the way battery energy storage systems (BESS) are operated. In this paper, we propose a framework to analyse battery operation in the Australian National Electricity Market (NEM) electricity spot and contingency reserve markets. We investigate battery operation in different states of Australia under various operating strategies. By considering battery degradation costs within the operating strategy, BESS can generate revenue from the energy market without significantly compromising battery life. Participating in contingency m... [more]

We examine the energy use impacts of energy efficiency and solar PV projects financed by residential property assessed clean energy (R-PACE) programs in California. We leverage household-level interval meter data to apply normalized metered energy consumption (NMEC) methods at significant scale—more than 25,000 electric meters and more than 15,000 gas meters. We develop a comparison group to account for non-project-related changes in usage. The projects include homes that replaced existing HVAC equipment with higher-efficiency units and homes that installed central heating or air conditioning equipment for the first time. We have limited information on pre-project household equipment stock so we develop a method to infer new installations. We find that projects that installed energy efficiency technologies reduce electricity consumption by approximately 3% and gas consumption by approximately 3.5% on average. When we remove homes that installed new cooling and heating equipment for the... [more]

This paper presents the development of a supercapacitor energy storage system (ESS) aimed to minimize weight, which is very important for aerospace applications, whilst integrating smart functionalities like voltage monitoring, equalization, and overvoltage protection for the cells. The methodology for selecting the supercapacitor cells type/size is detailed to achieve the safest and most energy-dense ESS. Additionally, the development of the interface electronics for cells’ voltage monitoring and overvoltage protection is presented. The proposed design implements a modular distributed architecture coordinated using communication buses to minimize the wirings and associated complexity and to enable system reconfiguration and expansions, as well as fault diagnoses. Validating the proposed ESS functionalities has been done via experimental testing and the results are presented and discussed.

Solar-powered air conditioners offer a high potential for energy-efficient cooling with a high economic feasibility. They can significantly reduce the energy consumption in the building sector, which is essential to meet the greater ambition of reducing greenhouse gas emissions by 80% in the EU by 2050. This paper presents a computational model development capable of simulating the behaviour of a photovoltaic-assisted heat pump in different locations and working conditions. In addition, this model has been used to optimise a solar on-grid air conditioning system. The generated model has been validated with experimental data obtained in a real facility for a whole summer of operation (more than 100 tested days) in a Mediterranean climate (Alicante, Spain). According to the simulation results, the average Energy Efficiency Ratio (EER) of the system is 16.0, 10.7 and 7.8 in Barcelona, Madrid and Seville, respectively. The optimisation analysis has proven that the severity of the climatic... [more]

The objective of the study was to demonstrate attitudes towards wind energy facilities in the area of the Korsze Commune. The results of the study were processed using structure indices calculated from the respondents’ answers, which were analyzed in terms of social and economic factors. The study revealed that both the NIMBY syndrome and the lack of civic engagement influence attitudes towards renewable energy technologies in rural areas. The NIMBY (“not in my backyard”) term describes negative public attitudes towards proposed development projects. However, some trends towards more pronounced attitudes can be observed, depending on socioeconomic conditions. The research results imply that the measures taken to promote renewable energy technologies should be designed differently depending on the socioeconomic situation of the targeted audience. Young people might be reached via social media appropriate to their age, and through campaigns promoting local investments. For older people,... [more]

With increased usage, individual batteries within the battery pack will begin to show disparate voltage and State of Charge (SOC) profiles, which will impact the time at which batteries become balanced. Commercial battery management systems (BMSs), used in electric vehicles (EVs) and microgrids, typically send out signals suggesting removal of individual batteries or entire packs to prevent thermal runaway scenarios. To reuse these batteries, this paper presents an analysis of an off-the-shelf Orion BMS with a constrained cycling approach to assess the voltage and SOC balancing and thermal performances of such near-to-second life batteries. A scaled-down pack of series-connected batteries in 6s1p and 6s2p topologies are cycled through a combination of US06 drive and constant charge (CC) profiles using an OPAL-RT real-time Hardware-in-the-loop (HIL) simulator. These results are compared with those obtained from the Matlab/Simulink model to present the error incurred in the simulation en... [more]

Reconstructable dynamic simulation models of modern variable-speed wind turbines (WTs), which are integrable into any simulation software, are crucial to the scientists investigating the contribution of WTs to counteracting the current power system stability issues. The structural similarity between a doubly fed induction-generator-based (DFIG-based) WT model and a full-scale-convertor-based (FSC-based) WT model using induction generator offers the possibility of integrating them into a combined modular model with little effort and the same used parameter set. This article presents a combined root mean square (RMS) WT model, which contains a DFIG-based WT and a FSC-based WT using induction generator. The model is designed based on fundamental machine and converter equations and can be applied for classical network stability analyses. Furthermore, analogous well-performing initialization procedures for both DFIG-based and FSC-based WT models are also introduced. As an example, to demons... [more]

Due to the energy transformation in buildings, the proportions of energy consumption for heating, ventilation and domestic hot water preparation (DHW) have changed. The latter component can now play a significant role, not only in the context of the annual heat demand, but also in the context of selecting the peak power of the heat source. In this paper, the comparison of chosen methods for its calculation is presented. The results show that for contemporary residential buildings, the peak power for DHW preparation can achieve the same or higher value as the peak power for heating and ventilation. For this reason, nowadays the correct selection of the peak power of a heat source for DHW purposes becomes more important, especially if it uses renewable energy sources, because it affects its size and so the investment cost and economic efficiency. It is also indicated that in modern buildings, mainly accumulative systems with hot water storage tanks should be taken into account because th... [more]

This study provides a workflow and preliminary estimations of the estimated ultimate recovery (EUR) volumes for natural gas and condensate liquids in the Tuwaiq Mountain Formation, the principal target in the Jafurah Field development project in Saudi Arabia. The strategic need for the field development is reviewed and the field characteristics are outlined based on public data sources complemented with data from analogous reservoirs. The target zone in the Jafurah Basin is a carbonaceous shale, being developed with up to 10,000-ft-long multistage-fractured laterals with 30 ft perforation cluster spacing and an assumed typical 1250 ft well spacing. The field will come on stream in 2024, when the gas-gathering pipeline system, natural gas processing plant, and underground gas storage facilities will all be in place. The range of uncertainties in the key reservoir parameters is taken into account to estimate preliminary EUR volumes (P90, P50, and P10) for both gas and condensates. Based... [more]

Developing energy from renewable sources and modernizing the energy system are critical components of China’s efforts to combat climate change. Policymakers and authorities have made significant attempts to bring them. However, one of the major impediments to China’s energy revolution is financial limitations, which are inextricably linked to the country’s economic growth. The present research paper intends to investigate the relationship between economic growth and sustainable financial development on the use of energy from renewable sources in both the short and long run in the context of China. To achieve this, the researchers have utilized the panel data consisting of 10 years from 2011 to 2020. When compared to cross-sectional and time-series data samples, the panel data model offers many benefits. For starters, the panel data includes information on the passage of time and the cross-sectional area. Another benefit of using panel-data models with a larger degree of freedom is that... [more]

This paper presents the performance analysis of a latest-generation hybrid vehicle (Toyota Yaris 2020) with a testing campaign in real road conditions and a comparison with the previous model (Toyota Yaris 2017). The study was conducted by applying the Real Drive Truth Test protocol, developed by the research group, validated and spread to other full hybrid vehicles: Toyota Prius IV (2016) and Toyota Yaris 2017 (2017). In the case of the 2020 tests, the co-presence on board—deemed unsafe in the usual ways given the ongoing pandemic—was achieved through precise and sophisticated remote control. An on-board diagnostic computer, video transmission and recording equipment guarantee the virtual co-presence of a technical control room and a driver. Thus, several engineers can follow and monitor each vehicle via a 4G modem (installed in each vehicle), analysing data, route and driver behaviour in real-time, and therefore even in the presence of a single occupant in the car under test. The utm... [more]

Cattle biomass (CB or manure from cattle) is proposed as reburn fuel under slightly fuel-rich conditions. The CB includes wastes from cattle feedlots (cattle grown in feedlots to slaughter weights of 450−640 kg) termed as Feedlot Biomass (FB) and cattle wastes from dairy farms termed as Dairy Biomass (DB). NOx emissions from coal-fired power plants can be reduced by using pure CB and Coal:CB mixtures as reburn fuels (10~30% by heat) injected after the primary combustion region. Experiments with Coal:CB mixtures as reburn fuels were performed using the 30 kW burner facility. Part I deals with results from experiments using pure FB and Coal:FB blends as reburn fuels while Part II presents results on extent of NOx reduction using pure DB and Coal:DB blends as reburn fuels (RF). In the current work, results on NOx emission are presented with FB and Coal:FB blends as RF. The parametric studies include: equivalence ratio in reburn zone (ERRBZ), vitiated air, angle of reburn nozzles, presence... [more]

One of the most effective technologies involving the use of lignocellulosic biomass is the production of biofuels, including methane-rich biogas. In order to increase the amount of gas produced, it is necessary to optimize the fermentation process, for example, by substrate pretreatment. The present study aimed to analyze the coupled effects of microwave radiation and the following acids: phosphoric(V) acid (H3PO4), hydrochloric acid (HCl), and sulfuric(VI) acid (H2SO4), on the destruction of a lignocellulosic complex of maize silage biomass and its susceptibility to anaerobic degradation in the methane fermentation process. The study compared the effects of plant biomass (maize silage) disintegration using microwave and conventional heating; the criterion differentiating experimental variants was the dose of acid used, i.e., 10% H3PO4, 10% HCl, and 10% H2SO4 in doses of 0.02, 0.05, 0.10, 0.20, and 0.40 g/gTS. Microwave heating caused a higher biogas production in the case of all acids... [more]

The power system is going through a change in its very foundations. More and more power converters are being integrated into the electric grid to interface renewable energy resources and in high-voltage direct-current (HVDC) transmission systems. This article presents a discussion on the stability of power systems when HVDC transmission systems based on modular multilevel converters (MMC) are connected in grid-forming (GFM) mode to the legacy power system using concepts of energy functions and Lyapunov stability theory and considering aspects of the interoperability between GFM converter technologies. As a base for the stability analysis, we review the main GFM converter technologies (droop and virtual synchronous machine), highlighting their differences. Then, we present a model using the center-of-inertia formulation for a multi-machine/multi-GFM converter power system representing a close future scenario of power systems where GFM converters might adopt different technologies. To il... [more]

The offshore wind sector is expanding to deep water locations through floating platforms. This poses challenges to horizontal axis wind turbines (HAWTs) due to the ever growing size of blades and floating support structures. As such, maintaining the structural integrity and reducing the levelised cost of energy (LCoE) of floating HAWTs seems increasingly difficult. An alternative to these challenges could be found in floating offshore vertical axis wind turbines (VAWTs). It is known that VAWTs have certain advantages over HAWTs, and in fact, some small-scale developers have successfully commercialised their onshore prototypes. In contrast, it remains unknown whether VAWTs can offer an advantage for deep water floating offshore wind farms. Therefore, here we present a multi-criteria review of different aspects of VAWTs to address this question. It is found that wind farm power density and reliability could be decisive factors to make VAWTs a feasible alternative for deep water floating... [more]

Problems such as global warming and rising oil prices are driving the implementation of ideas to reduce liquid fuel consumption and greenhouse gas emissions. One of them is the use of natural gas as an energy source. It is a hydrocarbon fuel with properties that allow the reduction of CO2 (Carbon Dioxide) emissions during combustion. Solutions are being implemented that allow for the use of natural gas to means of transport, namely in trucks of various categories and intended use. These installations are used in new vehicles, but also in the form of conversion for used cars, usually several years old. The article presents the results of tests of an engine from a used semi-trailer truck with a mileage of approx. 800 thousand km, with the compressed natural gas supply system installed. This installation (hardware and software), depending on the engine operating conditions, enables the replacement of up to 80% of diesel (base fuel) with natural gas. The impact of changing the fuel supply... [more]

Global efforts to tame CO2 emissions include the use of renewable energy sources, such as geo-energy harnessing. However, injecting pressurised fluids into the deep underground can induce earthquakes, hence converting CO2-related risk into seismic risk. Induced seismicity hazard is characterised by the overall seismic activity afb that is normalised by the injected fluid volume V and the parameter b of the Gutenberg−Richter law. The (afb,b) set has so far been estimated for a dozen of reservoir stimulations, while at least 53 geothermal fluid stimulations are known to exist, based on our survey. Here, we mined the induced seismicity literature and were able to increase the number of estimates to 39 after calculating afb from related published parameters and by imputing b with its expectation where this parameter was missing (0.65 ≤ b ≤ 2.9, with mean 1.16). Our approach was a two-step procedure: we first reviewed the entire literature to identify seismic hazard information gaps and the... [more]

The Special Issue entitled “Heat Transfer, Refrigeration and heat Pumps” accepted papers covering a wide range of topics related to heat pumps, thermal energy storage, and low-Global Warming Potential (GWP) alternative refrigerants [...]