With the recent rising attention and debates on the role of natural gas, especially liquid natural gas, in energy transition, it is critical to have a consistent approach in assessing uncertainties and dynamics in the global gas market during the next two to three decades. There are two objectives of this paper. The first one is to estimate and discuss the impacts of the global liquified natural gas (LNG) trade under a low-carbon scenario using a partial equilibrium model. The second objective is to discuss the role of a structural economic model in empirical analysis and strategy design under a regime shift, such as an energy transition, for the global natural gas market.

Energy safe is mandatory for all isolated IoT tools, such as in long way roads, mountains, or even in smart cities. If increasing the lifetime of these tools, the rentability of the global network loop becomes more efficient. Therefore, this paper presents a new approach for saving energy inside the source nodes by supervising the state of energy inside each source node and calculating the duty cycle factor. The relationship between these parameters is based on an optimization problem formulation. In this respect, the present paper is designed to propose a new approach that deals with increasing the lifetime of the wireless sensor network (WSN)-attached nodes, as fixed in the application. The newly devised design is based on implementing the IEEE 802.15.4 standard beacon-enabled mode, involving a cluster tree topology. Accordingly, every subgroup is allotted to apply a specifically different duty cycle, depending on the battery’s remaining energy level, which contributes to creating a... [more]

Research on corona discharge, shared by physics, chemistry and electrical engineering, has not arrested yet. As a dissipative process, the development of corona increases the resistive losses of transmission lines and enhances the line capacitance locally. Introducing additional losses and propagation delay, along the line, non-linearity and non-uniformity of the line parameters; therefore, corona should not be neglected. The present work is meant to provide the reader with comprehensive information on the corona macroscopic phenomenology and development, referring to the most relevant contributions in the literature on this subject. The models proposed in the literature for the simulation of the corona development are reviewed in detail, and sensitivity curves are provided to highlight their dependence on the input parameters.

A residential cogeneration system (CGS) is highlighted because of its efficient energy usage on both the supplier and consumer sides. It generates electricity and heat simultaneously; however, there is insufficient information on the efficiency according to the condition of usage. In this study, we analysed the performance data measured by the home energy management system (HEMS) and the lifestyle data of residents in a condominium of 356 flats where fuel cell CGS was installed in each flat. The electricity generated by CGS contributed to an approximately 12% reduction in primary energy consumption and CO2 emission, and the rate of generation by the CGS in the electric power demand (i.e., contribution rate) was approximately 38%. The electricity generation was mainly affected by the use of electricity up to 4 MWh/household/year. Gas or water use also impacted electric power generation, with water use as the primary factor affecting the contribution rate. Electric power generation chang... [more]

The proposal of new technologies capable of producing electrical energy from renewable sources has driven research into seas and oceans. Research finds this field very promising in the future of renewable energies, especially in areas where there are specific climatic and morphological characteristics to exploit large amounts of energy from the sea. In general, this kind of energy is referred to as six energy resources: waves, tidal range, tidal current, ocean current, ocean thermal energy conversion, and saline gradient. This review has the aim to list several wave-energy converter power plants and to analyze their years of operation. In this way, a focus is created to understand how many wave-energy converter plants work on average and whether it is indeed an established technology.

The continued use of fossil fuels is contributing to severe environmental pollution and the establishment of an abnormal climate; consequently, alternative renewable energy sources are being actively investigated worldwide. Further, following global trends, numerous countermeasures aimed at improving carbon neutrality, promoting sustainable agriculture, and reducing fossil fuel dependence are being implemented in the Republic of Korea. Therefore, this study was conducted to investigate the application of renewable energies for greenhouse heating in the Republic of Korea. Three hybrid systems, numbered 1−3, were constructed using a pellet boiler, hydrothermal heat pump, and solar heat collection system, respectively. Thereafter, the heating performance, combined heat efficiency, energy consumption per temperature lifting, and energy cost per temperature lifting of the systems were compared. The combined thermal efficiency results showed no significant differences. However, in terms of e... [more]

Wind turbine pitch system condition monitoring is an active area of research, and this paper investigates the use of the Isolation Forest Machine Learning model and Supervisory Control and Data Acquisition system data for this task. This paper examines two case studies, turbines with hydraulic or electric pitch systems, and uses an Isolation Forest to predict failure ahead of time. This novel technique compared several models per turbine, each trained on a different number of months of data. An anomaly proportion for three different time-series window lengths was compared, to observe trends and peaks before failure. The two cases were compared, and it was found that this technique could detect abnormal activity roughly 12 to 18 months before failure for both the hydraulic and electric pitch systems for all unhealthy turbines, and a trend upwards in anomalies could be found in the immediate run up to failure. These peaks in anomalous behaviour could indicate a future failure and this wo... [more]

Within China’s renewable energy industry, the importance of the solar photovoltaic industry has been increasingly recognized. Many Chinese provinces have adopted various measures to develop the solar photovoltaic industry. This study used the diamond model and the analytic hierarchy process to clarify the relative importance of the determinants of the development of the solar photovoltaic industry. A total of 22 determinants in six categories (i.e., factor condition; demand condition; firm strategy, structure, and rivalry; related and support industries; government; and chance) were analyzed. The results show that besides factor condition, demand condition and firm strategy, structure, and rivalry have also had a strong influence on the development of China’s photovoltaic industry. The findings also indicate that some traditional factors, such as labor costs and acquiring land, are very important to the development of the solar photovoltaic industry. The relative importance of the dete... [more]

Mosques are quite different from other building types in terms of occupant type and usage schedule. For this reason, they should be evaluated differently from other building types in terms of thermal comfort and energy consumption. It is difficult and probably not even necessary to create homogeneous thermal comfort in mosques’ entire usage area, which has large volumes and various areas for different activities. Nevertheless, energy consumption should be at a minimum level. In order to ensure that mosques are minimally affected by outdoor climatic changes, the improvement of the properties of the building envelope should have the highest priority. These optimal properties of the building envelope have to be in line with thermal comfort in mosques. The proposed method will be a guide for designers and occupants in the design process of new mosques or the use of existing mosques. The effect of the thermal properties of the building envelope on energy consumption was investigated to ensu... [more]

The occurrence of voltage violations is a major deterrent for absorbing more rooftop solar power into smart Low-Voltage Distribution Grids (LVDGs). Recent studies have focused on decentralized control methods to solve this problem due to the high computational time in performing load flows in centralized control techniques. To address this issue, a novel sensitivity matrix was developed to estimate the voltages of the network by replacing load flow simulations. In this paper, a Centralized Active, Reactive Power Management System (CARPMS) is proposed to optimally utilize the reactive power capability of smart Photovoltaic (PV) inverters with minimal active power curtailment to mitigate the voltage violation problem. The developed sensitivity matrix is able to reduce the time consumed by 55.1% compared to load flow simulations, enabling near-real-time control optimization. Given the large solution space of power systems, a novel two-stage optimization is proposed, where the solution spa... [more]

Germany’s energy transition, known as ‘Energiewende’, was always very progressive. However, it came technically to a halt at the question of large-scale, seasonal energy storage for wind and solar, which was not available. At the end of the 2000s, we combined our knowledge of both electrical and process engineering, imitated nature by copying photosynthesis and developed Power-to-Gas by combining water electrolysis with CO2-methanation to convert water and CO2 together with wind and solar power to synthetic natural gas. Storing green energy by coupling the electricity with the gas sector using its vast TWh-scale storage facility was the solution for the biggest energy problem of our time. This was the first concept that created the term ‘sector coupling’ or ‘sectoral integration’. We first implemented demo sites, presented our work in research, industry and ministries, and applied it in many macroeconomic studies. It was an initial idea that inspired others to rethink electricity as we... [more]

Impingement heat transfer is considered one of the most effective cooling technologies that yield high localized convective heat transfer coefficients. This paper studies different configurable parameters involved in jet impingement cooling such as, exit orifice shape, crossflow regulation, target surface modification, spent air reuse, impingement channel modification, jet pulsation, and other techniques to understand which of them are critical and how these heat-transfer-enhancement concepts work. The aim of this paper is to excite the thermal sciences community of this efficient cooling technique and instill some thoughts for future innovations. New orifice shapes are becoming feasible due to innovative 3D printing technologies. However, the orifice shape variations show that it is hard to beat a sharp-edged round orifice in heat transfer coefficient, but it comes with a higher pressure drop across the orifice. Any attempt to streamline the hole shape indicated a drop in the Nusselt... [more]

In this article, a quasi-switched boost converter based on the switched-capacitor technique with high step-up voltage capability is dealt with and analyzed. The proposed converter offers a simple structure and low voltage stress on the semiconductor elements with intrinsic small duty cycle. An inductor of the proposed converter is connected in series with the input voltage source; therefore, continuous input current ripple is attainable. In addition, the efficiency of the proposed converter is also improved. A detailed steady-state analysis is discussed to identify the salient features of the switched-capacitor-based quasi-switched boost DC-DC converter. The performance of the converter is compared against similar existing high boost DC-DC converters. Finally, the switched-capacitor-based quasi-switched boost DC-DC converter is investigated by experimental verification.

This paper presents a method for the probabilistic evaluation of the failure rates of mechanical components in a typical power take-off (PTO) system of a horizontal-axis tidal stream turbine (HATT). The method is based on a modification of the method of the influence factors, when base failure rates, relevant influence factors and, subsequently, resulting failure rates are treated as random variables. The prior (i.e., initial) probabilistic distribution of the failure rates of a HATT component is generated using data for similar components from other industries, while taking into account actual characteristics of the component and site-specific operating and environmental conditions of the HATT. A posterior distribution of the failure rate is estimated numerically based on a Bayesian approach as new information about the component performance in an operating HATT becomes available. The posterior distribution is then employed to obtain the updated mean and lower and upper confidence lim... [more]

With the improvement and development of micro-mechanical manufacturing technology, people can produce an increasing variety of micro-electromechanical systems in recent years, such as micro-satellite thrusters, micro-sensors, micro-aircrafts, micro-medical devices, micro-pumps, and micro-motors. At present, these micro-mechatronic systems are driven by traditional energy power systems, but these traditional energy power systems have such disadvantages as short endurance time, large size, and low energy density. Therefore, efforts were made to study micro-energy dynamical systems with small size, light gravity, high density and energy, and long duration so as to provide continuous and reliable power for these systems. In general, the micro-thermal photoelectric system not only has a simple structure, but also no moving parts. The micro-thermal photoelectric system is a micro-energy power system with good application prospects at present. However, as one of the most important structural... [more]

The article presents comprehensive results of research on two representative topologies of converters used in the path of processing energy generated in a wind turbine and transmitted to the grid. The topology T1 uses a two-level transistor-controlled rectifier as a converter from the generator side, while the T2 topology uses DC/DC boost converter. In both topologies, a three-level back-to-back converter with a line filter L was used as a grid converter. The conclusions indicate the tendency of changes in power losses depending on the aforementioned parameters and can be used at the stage of deciding on the choice of topology, operating parameters or selection of control methods depending on the specific operating conditions of the wind turbine.

The performance of turbochargers is heavily influenced by heat transfer. Conventional investigations are commonly performed under adiabatic assumptions and are based on the first law of thermodynamics, which is insufficient for perceiving the aerothermodynamic performance of turbochargers. This study aims to experimentally investigate the non-adiabatic performance of an automotive turbocharger turbine through energy and exergy analysis, considering heat transfer impacts. It is achieved based on experimental measurements and by implementing a novel innovative power-based approach to extract the amount of heat transfer. The turbocharger is measured on a hot gas test bench in both diabatic and adiabatic conditions. Consequently, by carrying out energy and exergy balances, the amount of lost available work due to heat transfer and internal irreversibilities within the turbine is quantified. The study allows researchers to achieve a deep understanding of the impacts of heat transfer on the... [more]

Not only the driving for offshore wind energy capacity of 12 GW by Korea’s Renewable Energy 2030 plan but also the need for the rejuvenation of existing world-class shipbuilders’ infrastructures is drawing much attention to offshore wind energy in Korea, especially to the diverse substructures. Considering the deep-sea environment in the East Sea, this paper presents detailed modeling and analysis of spar-type substructure for a 5 MW floating offshore wind turbine (FOWT). This process uses a fully coupled integrated load analysis, which was carried out using FAST, a widely used integrated load analysis software developed by NREL, coupled with an in-house hydrodynamic code (UOU code). The environmental design loads were calculated from data recorded over three years at the Ulsan Marine buoy point according to the ABS and DNVGL standards. The total 12 maximum cases from DLC 6.1 were selected to evaluate the structural integrity of the spar-type substructure under the three co-directional... [more]

The steelmaking industry requires coke as a reducing agent, as an energy source, and for its ability to hold slag in a blast furnace. Coking coal as raw coke material is very limited. Studying the use of biomass as a mixture of coking coal in the synthesis of biocoke is necessary to reduce greenhouse gas coal emissions. This research focuses on biomass and heating temperature through the coal blending method to produce biocoke with optimal mechanical properties for the blast-furnace standard. The heating temperature of biomass to biochar was evaluated at 400, 500, and 600 °C. The blending of coking coal with biochar was in the compositions of 95:5, 85:15, and 75:25 wt.%. A compacting force of 20 MPa was employed to produce biocoke that was 50 mm in diameter and 27 mm thick using a hot cylinder dye. The green sample was heated at 1100 °C for 4 h, followed by quenching with a water medium, resulting in dense samples. Increasing heating temperature is generally directly proportional to an... [more]

In this paper, a distributed energy storage design within an electric vehicle for smarter mobility applications is introduced. Idea of body integrated super-capacitor technology, design concept and its implementation is proposed in the paper. Individual super-capacitor cells are connected in series or parallel to form a string connection of super-capacitors with the associated management unit to form a panel. These super-capacitor panels are shaped to fit the alternative concept of vehicle design, and it solves the design issues and prepares for configurable electric vehicles. Body integration of super-capacitors enhances the acceleration, and regenerative braking performances of the electric vehicle increases the operating life of the Li-ion battery and improves space utilization by giving more area for the main energy source, the Li-ion battery. Integrating super-capacitor into the car body involves special packaging technology to minimize space and promotes distributed energy storag... [more]

In this study the NOx reduction capability of reburning three biomasses (i.e., wood pellet, torrefied biomass, and empty fruit bunch) via 12 cases (i.e., four reburning ratios for every biomass) is investigated in a 1 MWth-scale pilot-scale furnace. These reburning cases are compared with 12 cofiring cases presented in the Part 1 paper on a consistent basis. It is found that, for every cost to purchase and prepare biomass, reburning technology provides significantly better NOx abatement performance than cofiring (up to 3.4 times). NOx reduction effectiveness as high as 4.9 could be achieved by reburning, which means the percent of NOx abatement could be 4.9 times higher than the percent of reburning ratio. It is found that the highest NOx reduction per thermal unit of biomass happens at the lowest reburning ratio, and increasing the reburning ratio leads to a reduction in NOx abatement effectiveness in an exponential decay manner. Unlike cofiring technology, reburning was found to have... [more]

The development of wind energy and the increasing number of installed wind turbines make it necessary to assess them in terms of the nuisance of the emitted infrasound noise generated by such devices. The article presents the results of measurements and analyses of infrasound emitted during the operation of wind turbines installed in various locations in Poland. Comparative analysis of noise levels in the infrasound and audible range has shown that acoustic energy is mainly in the low and infrasound frequency range, and the measured levels depend significantly on the weighting curves used. On the basis of the results, it was confirmed that the sound pressure level of infrasound signals emitted by the operation of high-power wind turbines, regardless of wind velocity, weather conditions, design solutions of turbines, operating time, rated capacity, does not exceed the criteria specified in the applicable legislation dealing with the assessment of infrasound noise on the working environm... [more]

Laboratory measurements and analyses conducted in a wide range of changes of water temperature and mass flow rate for different types of radiators allowed to provides limitations and assessment of the current radiators heat transfer model according to EN 442. The inaccuracy to determinate the radiator heat output according to EN 442, in case of low water mass flow rates may achieve up to 22.3% A revised New Extended Heat Transfer Model in Radiators NEHTMiRmd is general and suitable for different types of radiators both new radiators and radiators existing after a certain period of operation is presented. The NEHTMiRmd with very high accuracy describes the heat transfer processes not only in the nominal conditions—in which the radiators are designed, but what is particularly important also in operating conditions when the radiators water mass flow differ significantly from the nominal value and at the same time the supply temperature changes in the whole range radiators operating during... [more]

Thermal treatments such as torrefaction and fast pyrolysis are commonly employed methods to produce biofuels with high-energetic properties. In this study, wood chips were heat-treated at different temperatures of torrefaction (315 °C) and fast pyrolysis (400 and 454 °C) to form energetic pellets. Three softwoods, jack pine (JP), balsam fir (BF), and black spruce (BS), were evaluated. Pellets are produced using 20% moisture content and 15% pyrolytic lignin as a binder. Untreated- and treated-wood residues were characterized by surface chemistry, elemental analysis, and chemical composition, whereas all pellets were characterized in terms of density, high heat value (HHV), and durability. Results showed that both thermal treatments caused significant changes in the physicochemical structure of wood residues. Using temperatures higher than 315 °C leads to the disappearance of hydroxyl groups, a decrease in oxygen and hydrogen contents, and an increase in carbon content. Regardless of the... [more]

Replacing fossil jet fuel with biojet fuel is an important step towards reducing greenhouse gas (GHG) emissions from aviation. To this end, Sweden has adopted a GHG mandate on jet fuel, complementing those on petrol and diesel. The GHG mandate on jet fuel requires a gradual reduction in the fuel’s GHG emissions to up to 27% by 2030. This paper estimates the potential production of biojet fuel in Sweden for six integrated production pathways and analyzes what they entail with regard to net biomass input and the amount of hydrogen required for upgrading to fuel quality. Integrated production of biofuel intermediates from forestry residues and by-products at combined heat and power plants as well as at the forest industry, followed by upgrading to biojet fuel and other transportation fuels at a petroleum refinery, was assumed in all the pathways. The potential output of bio-based transportation fuels was estimated to 90 PJ/y, including 22 PJ/y of biojet fuel. The results indicate that it... [more]