Wind power plants depend greatly on weather conditions, thus being considered intermittent, uncertain and non-dispatchable. Due to the massive integration of this energy resource in the recent decades, it is important that transmission and distribution system operators are able to model their electrical behaviour in terms of steady-state power flow, transient dynamic stability, and short-circuit currents. Consequently, in 2015, the International Electrotechnical Commission published Standard IEC 61400-27-1, which includes generic models for wind power generation in order to estimate the electrical characteristics of wind turbines at the connection point. This paper presents, describes and details the models for wind turbine topologies Types 1 and 2 following IEC 61400-27-1 for electrical simulation purposes, including the values for the parameters for the different subsystems. A hardware-in-the-loop combined with a real-time simulator is also used to analyse the response of such wind t... [more]

Most technoeconomic feasibility studies of photovoltaic (PV) systems with batteries are mainly focused on the load demand, PV system profiles, total system costs, electricity price, and the remuneration rate. Nevertheless, most do not emphasise the influence degradation process such as corrosion, sulphation, stratification, active material seeding, and gassing on battery lifetime, efficiency, and capacity. In this paper, it is analysed the influence of the degradation processes in lead−acid batteries on the technoeconomic analysis of PV systems with and without battery. Results show that Net Present Value (NPV), Payback Period (PBP), and Discounted PayBack Period (DPBP) have a heavy dependence on the assumptions about the value of the battery performance parameters according to its degradation processes. Results show NPV differences in the range from −307% to 740%, PBP differences in the range from 9% to 188%, and DPBP differences in the range from 0% to 211%.

In recent times, the field of wireless sensor networks (WSNs) has attained a growing popularity in observing the environment due to its dynamic factors. Sensor data are gathered and forwarded to the base station (BS) through a wireless transmission medium. The data from the BS is further distributed to end-users using the Internet for their post analysis and operations. However, all sensors except the BS have limited constraints in terms of memory, energy and computational resources that degrade the network performance concerning the network lifetime and trustworthy routing. Therefore, improving energy efficiency with reliable and secure transmissions is a valuable debate among researchers for critical applications based on low-powered sensor nodes. In addition, security plays a significant cause to achieve responsible communications among sensors due to their unfixed and variable infrastructures. Keeping in view the above-mentioned issues, this paper presents an energy-aware graph clu... [more]

Recently, the development of non-precious electrocatalysts for the oxygen reduction reaction (ORR) has become important in replacing currently employed platinum (Pt)-based catalysts. Although Pt-based catalysts exhibit satisfactory ORR performances, their high price, easy methanol/CO2 poisoning, and poor long-term stability significantly hamper the forward movement of fuel cell technology. Among the various candidates, graphene-supported iron phthalocyanine (FePc) composites have attracted great attention because of their unique advantages, including low cost, good dimensional stability, high durability, and tunable catalytic activity. In the composite catalyst, FePc molecules are immobilized on graphene via noncovalent or covalent interactions. In addition, two-dimensional graphene substrates can improve not only the electrical conductivity of the composite, but also the dispersion of FePc molecules, triggering a significant improvement in the catalytic properties of the composite cat... [more]

The China Fusion Engineering Test Reactor (CFETR) is a tokamak device to validate and demonstrate fusion engineering technology. In CFETR, the breeding blanket is a vital important component that is closely related to the performance and safety of the fusion reactor. Neutronics/thermal-hydraulics (N/TH) coupling effect is significant in the numerical analysis of the fission reactor. However, in the numerical analysis of the fusion reactor, the existing coupling code system mostly adopts the one-way coupling method. The ignorance of the two-way N/TH coupling effect would lead to inaccurate results. In this paper, the MCNP/FLUENT code system is developed based on the 3D-1D-2D hybrid coupling method. The one-way and two-way N/TH coupling calculations for two typical blanket concepts, the helium-cooled solid breeder (HCSB) blanket and the water-cooled ceramic breeder (WCCB) blanket, are carried out to study the two-way N/TH coupling effect in CFETR. The numerical results show that, compare... [more]

The empirical conclusions regarding the relationship between energy price and energy efficiency are relatively mixed. This paper systematically examines the influence of energy price on energy efficiency in China based on data from 30 provinces between 2003 and 2017, using linear and nonlinear effect analysis. We found that the impact of energy price on energy efficiency in China was positive in general. However, there existed heterogeneous effects of energy price on energy efficiency in various regions, and the effect differed with differences in energy efficiency levels based on the panel quantile regression analysis. Finally, the nonlinear effect analysis based on the panel threshold model indicated that the effect of energy price on energy efficiency increased with the rise of the environmental regulation level and economic growth rate, while it decreased with the ascent of the degree of energy price distortion and economic development level. In particular, when the value of a regi... [more]

Following the recent development trend in the struggle for cleaning the earth’s environment, solar is the one of most promising area that can partially be used as a replaceable energy from non-renewable fuel sources. As such, it plays a significant role in protecting the environment from global warming. As solar power does not emit harmful gases into the atmosphere, its production, distribution, setup, and operation are vital should the production remain constant. Even solar energy waste emissions are small; when compared to current energy sources, the amount of harmful gases is negligible. This paper presented an integrated approach for site of solar plants by using data envelopment analysis (DEA) and Fuzzy Analytical Network Process (FANP). Furthermore, these integrated methodologies, incorporated with the most relevant parameters of requirements for solar plants, are introduced. First, the paper considers an integrated hierarchical DEA and FANP model for the optimal geographical loc... [more]

With the rapidly increasing number of electric vehicle users, in many urbans transport networks, there are mixed traffic flows (i.e., electric vehicles and gasoline vehicles). However, limited by driving ranges and long battery recharging, the battery electric vehicle (BEV) drivers’ route choice behaviors are inevitably affected. This paper assumes that in a transportation network, when BEV drivers are traveling between their original location and destinations, they tend to select the path with the minimal driving times and recharging time, and ensure that the remaining charge is not less than their battery safety margin. In contrast, gasoline vehicle drivers tend to select the path with the minimal driving time. Thus, by considering BEV drivers’ battery management strategies, e.g., battery safety margins and en-route recharging behaviors, this paper developed a mixed user equilibrium model to describe the resulting network equilibrium flow distributions. Finally, a numerical example i... [more]

Oil shale is one of the alternative energies and fuel solutions in Jordan because of the scarcity of conventional sources, such as petroleum, coal, and gas. Oil from oil shale reservoirs can be produced commercially by pyrolysis technology. To optimize the process, mechanisms and rates of reactions need to be investigated. Omari oil shale formation in Jordan was selected as a case study, for which no kinetic models are available in the literature. Oil shale was analyzed using the Fischer assay method, proximate analysis (moisture, volatile, and ash), gross calorific value, elemental analysis (CHNS), and X-ray fluorescence (XRF) measurements. Non-isothermal thermogravimetric analysis was applied to study the kinetic parameters (activation energy and frequency factor) at four selected heating rates (5, 10, 15, and 20 °C/min). When oil shale was heated from room temperature to 1100 °C, the weight loss profile exhibited three different zones: drying (devolatilization), pyrolysis, and miner... [more]

Isolated communities are progressively integrating renewable generation to reduce the societal, economic and ecological cost of diesel generation. Unfortunately, as renewable penetration and load variability increase, systems require greater diesel generation reserves, constraining renewable utilisation. Improved diesel generator flexibility can reduce the requirement for diesel reserves, allowing increased renewable hosting. Regrettably, it is uncommon for utilities to modify diesel generator control during the integration of renewable source generation. Identifying diesel generator flexibility and co-ordination as an essential component to optimising system hosting capacity, this paper investigates improved diesel generator flexibility and coordination via low-load diesel application. Case study comparisons for both high- and low-penetration hybrid diesel power systems are presented in King Island, Australia, and Moloka`i, Hawai`i, respectively. For King Island, the approach details... [more]

Wheat straw without pre-treatment is only converted to methane to a low degree during anaerobic digestion for fuel production due to its low hydrolysis. Current pre-treatment technologies are challenged by high expenses to energy or chemical agents. We examined the low-tech co-ensiling pre-treatment as an alternative pre-treatment of wheat straw, and compared the results with hydrothermal, chemical and mechanical pre-treatment methods. The effects of co-ensiling duration and the mixing ratio between straw and sugar beet root on the methane yields, surface morphology and chemical composition were examined. It was found that co-ensiling could improve production of methane by 34.7%, while a combined hydrothermal and chemical pre-treatment could increase the production of methane by 25.4%. The study demonstrated that the effect of co-ensiling could overlap with hydrothermal and chemical pre-treatment by having similar effects to increase lignocellulosic hydrolysis and improve methane produ... [more]

In this paper, the dynamic responses of a large-scale multiple-support road viaduct to mining-induced seismic events registered in two regions of mining activity were compared. The regions differ in geological structure, which results in discrepancies in the dominant frequency content. Spatial variation of ground motion causing the kinematic excitation non-uniformity was accounted for in the dynamic analyses of this large-scale structure. Non-uniform mining-induced kinematic excitation models were proposed, with respect to the specificity of mining origin quakes. The dynamic performance of the viaduct was determined using three different methods of calculation: the time history analysis, the response spectrum analysis, and the multiple support response spectrum analysis. Both the uniform and non-uniform kinematic excitation models were adopted for the dynamic performance assessment. The research revealed that the dynamic response of some members of the structure, determined using the n... [more]

In previous studies on the indirect rebound effect due to income saved from energy efficiency improvement by households in an input−output model, household income is typically assumed constant before and after an efficiency improvement of their energy use. The assumption is implausible if we observe that households may not re-spend the saved income, which potentially reduces their consumption and national income including households, at least in the short term, in a country like China, where they have high saving propensity. In addition, income of other economic agents than households may also be affected. In this article, we provide an improved input−output model to clarify the issue and then use the 2017 input−output data of China to illustrate the potential indirect rebound effect due to household income saved from an energy efficiency improvement. Our results show that if the income impact in the short term is properly considered, then the indirect rebound effect due to the income... [more]

Adsorption refrigeration systems are promising, sustainable solutions for many cooling applications. The operating range and the performance of an adsorption cooling cycle are strongly dependent on the properties of adsorbents, adsorbates, and bed coatings. Therefore, further research and analysis may lead to improved performance of adsorption coolers. In this paper, studies on working pairs using natural refrigerants and the properties of adsorbent coatings were reviewed. The selected working pairs were then thermodynamically characterised and ranked in terms of refrigerant evaporation temperature values. This was found to be a key parameter affecting the applicability of a given adsorbent/adsorbate pair and the value of SCP (Specific Cooling Power), COP (Coefficient of Performance) parameters, which are now commonly used comparison criteria of adsorption chillers. In the analysis of the coating studies, the focus was on the effect of individual parameters on the performance of the co... [more]

Climate change has visible effects with growing dynamics in the last decades [...]

This study proposes a building energy simulation (BES) model of an air-to-water heat pump (AWHP) system integrated with a multi-span greenhouse using the TRNSYS-18 program. The proposed BES model was validated using an experimental AWHP and a multi-span greenhouse installed in Kyungpook National University, Daegu, South Korea (latitude 35.53° N, longitude 128.36° E, elevation 48 m). Three AWHPs and a water storage tank were used to fulfill the heat energy requirement of the three-span greenhouse with 391.6 m2 of floor area. The model was validated by comparing the following experimental and simulated results, namely, the internal greenhouse temperature, the heating load of the greenhouse, heat supply from the water storage tank to the greenhouse, heat pumps’ output water temperature, power used by the heat pumps, coefficient of performance (COP) of the heat pump, and water storage tank temperature. The BES model’s performance was evaluated by calculating the root mean square error (RMS... [more]

Shadows severely affect the performance of solar photovoltaic (PV) systems. A proper description of this effect is useful for sizing and simulating PV systems when shadows cannot be avoided. Shading factors represent the basis for simulating the effect of shadows on solar modules. These factors can be used to estimate shading losses, calculate their I-V and P-V curves under shading conditions, or develop new maximum power point tracking (MPPT) techniques. Open-source libraries focused on solar energy have gained popularity in recent years. One of the currently most popular ones is the PV_LIB toolbox initially developed by Sandia Laboratories. PV_LIB significantly facilitates solar energy calculations. However, it currently lacks functions for taking into account shaded conditions. In this paper, a detailed Matlab-based method for calculating the shading factors is provided. The method has been used for elaborating a toolbox for shading calculations. The current work could help extend t... [more]

Wave energy is one of the most promising renewable energies available with its very large resource. The waves generated by the wind field are steadier than the wind field itself, rendering wave energy more consistent than wind energy. It is also more predictable than wind and solar. Wave energy is making continuous progress towards commercialisation, and thanks to an increasing number of deployments at sea, the sector is increasing the understanding of the costs and economies of these projects. No wave energy converter has been demonstrated to be commercially viable, and it is yet to be proven that wave energy can contribute to the renewable energy mix. In this context, and in order to find an economically viable solution for exploiting wave energy, it is important to assess the economic potential of a particular concept throughout the entire technological development process. At early development stages, this assessment can be challenging and present large uncertainties. Notwithstandi... [more]

We address the control of a hybrid energy storage system composed of a lead battery and hydrogen storage. Powered by photovoltaic panels, it feeds a partially islanded building. We aim to minimize building carbon emissions over a long-term period while ensuring that 35% of the building consumption is powered using energy produced on site. To achieve this long-term goal, we propose to learn a control policy as a function of the building and of the storage state using a Deep Reinforcement Learning approach. We reformulate the problem to reduce the action space dimension to one. This highly improves the proposed approach performance. Given the reformulation, we propose a new algorithm, DDPGαrep, using a Deep Deterministic Policy Gradient (DDPG) to learn the policy. Once learned, the storage control is performed using this policy. Simulations show that the higher the hydrogen storage efficiency, the more effective the learning.

Strategically critical elements are becoming significant for the rising demand of emerging energy-efficient technologies and high-tech applications. These critical elements are mostly geologically dispersed, and mainly recovered from recycled materials. Coal with high concentrations of critical elements is supposed to stable alternative sources. The abundances of critical elements in coal varies widely among different deposits and regions. The high concentrations of critical elements are found in many Chinese and Russian coal ores. The global mining potential ratio (MPR) is applied and suggests scandium, hafnium, cesium, yttrium, germanium, gallium, thallium, strontium and rare-earth elements could be potential recovery from coal. A number of benefits are expected with the extraction of critical elements during coal utilization.

In some cases, the oil shale deposited in shallow lakes may be genetically associated with the coal-bearing successions. Although paleovegetation is an important controlling factor for the formation of oil shale- and coal-bearing successions, few studies have focused on their joint characterization. In this study, a total of twenty-one oil shale and coal samples were collected from the upper member of the Lower Cretaceous Muling Formation (K1ml2) in the Laoheishan Basin, and investigated for their bulk geochemical, maceral, palynological, and terpenoid biomarker characteristics, in order to reconstruct the paleovegetation and reveal its influence on the formation of oil shale and coal. The K1ml2 is subdivided into lower, middle, and upper units. The studied oil shale samples from the lower and upper units display a high ash yield (Ad), low total organic carbon (TOC) and sulfur (S) contents, and limited hydrocarbon generation potential. The studied coal samples from the middle unit are... [more]

In this paper, alkyl aliphatic hydrazine, which is different from traditional polymer fluidity improver, was synthesized from aliphatic hydrazine and cetane bromide, and evaluated as a pour point and viscosity-reducer depressant for crude oil. The evaluation results showed that alkyl aliphatic hydrazone fully reduced the pour point and viscosity of crude oil with the increase of crude oil fluidity. The viscosity reduction rate of crude oil in Jinghe oilfield was 79.6%, and the pour point was reduced by about 11.3 °C. The viscosity reduction rate of crude oil in Xinjiang Oilfield was 74.7%, and the pour point was reduced by 8.0 °C. The long alkyl chain is beneficial to the eutectic of wax in crude oil, and the polar group inhibits the crystal growth, resulting in the decrease of pour point and viscosity. The waste oil is fully recycled into oilfield chemicals.

Climate change and efforts to mitigate it have given rise to an interest in the relationship between industry competitiveness, energy efficiency, and carbon emissions. A better understanding of this relationship can be essential for economic and environmental decision-makers. This paper presents empirical research evaluating industry competitiveness through the factors of energy efficiency and carbon emission in Europe’s most energy-intensive industries. The designed industry competitiveness measure index consists of seven components, grouped into three equally weighted sub-indexes: export performance, energy, and environmental. The export performance of the industry is described by the industry export growth rate, the share of the industry’s export, and the effects on the industry’s competitiveness of changes in a country’s export. The energy intensity of the industry and energy prices are integrated into the energy sub-index. The environmental sub-index consists of the industry’s emi... [more]

Energy efficiency, generation from renewable sources and more recently energy flexibility are key elements of present sustainability policies. However, we are beginning to see a recognition of the need to couple technological solutions with lifestyle and behavioral changes, sometimes labeled under the term “sufficiency”. Appropriate policies and design principles are necessary to enable sufficiency options, which in turn reveal that there is a bidirectional influence between the building and the district/city level. In this context, the authors discuss how city and building re-design should be implemented combining energy efficiency, flexibility, production from renewables and sufficiency options for achieving a positive energy balance at the district level even within the constraints of dense cities. Based on a review of recent advances, the paper provides a matrix of interactions between building and district design for use by building designers and city planners. It also compares po... [more]

In modern electrical power distribution systems, the effective operation of inverter-based arc suppression devices relies on the accuracy of faulty phase selection. In the traditional methods of faulty phase selection for single-phase-to-ground faults (SPGs), power frequency-based amplitude and phase characteristics are used to identify the faulty phase. In the field, when a high-resistance SPG occurs in the system, traditional methods are difficult for accurately identifying the faulty phase because of the weak fault components and complicated process. A novel realizable and effective method of faulty phase selection based on transient current similarity measurements is presented when SPGs occur in resonantly grounded distribution systems in this paper. An optimized Hausdorff distance matrix (MOHD) is proposed and constructed by the transient currents of three phases’ similarity measurements within a certain time window of our method. This MOHD is used to select the sampling time wind... [more]