In this study, the combustion of olive byproducts was investigated using the TG-FTIR technique. Different types of olive biomass were considered: twigs, leaves, olive-mill waste from the two-phase decanting method, and wastewater from the three-phase system. The reaction regions, ignition, and burnout temperatures at different heating rates were determined using TG/DTG analysis and the thermogravimetry results. Comprehensive combustion, ignition, burnout, and flammability indexes were also calculated. The highest combustion index values were obtained for waste from the three-phase system, followed by the two-phase decanting method, then with leaves and small twigs. The order of the index values indicated that the sample from the three-phase process ignited more quickly and yielded faster. The changes in activation energy calculated using different model-free isoconversional methods—Friedman, Ozawa−Flynn−Wall, and Kissinger−Akahira−Sunose—fell within the range of 130−140 kJ/kmol. FTIR a... [more]

The article describes the principles based on which it is possible to obtain energy from renewable sources more efficiently. The principles use the conventional DC-DC interleaved buck converter based on the common electronic component types and the control strategy. A novelty of such a proposed solution lies in the methods which are not new, but with the right combination, better results can be achieved. The resulting method can be implemented into various topologies where the highest efficiency for wide input power is required. In case of the renewable energy sources where the power can vary hugely during the day, the proposed method can be implemented. Therefore, the article provides several steps, from calculation through simulation to experimental results that brings reader close to understanding of a such proposed solution.

The focus of this study is under the auspices of China Steel Corporation, Taiwan, in carrying out the national energy policy of 2025 Non-Nuclear Home. Under this policy, an estimated 600 offshore wind turbines will be installed by 2025. In order to carry out the wind energy project effectively, a preliminary study must be conducted. In this article, we investigated the influence of the wake effect on the efficiency of the turbines’ layout in a windfarm. A distributed genetic algorithm is deployed to study the wind turbines’ layout in order to alleviate the detrimental wake effect. In the current stage of this research, the historical weather data of weather stations near the site of the 29th windfarm, Taiwan, were collected by Academia Sinica. Our wake effect resilient optimized windfarm showed superior performance over that of the conventional windfarm. Additionally, an operation cost minimization process is also demonstrated and implemented using an ant colony optimization algorithm... [more]

This paper presents an energy management strategy for secondary energy sources and their optimization in the context of the tax gap on mineral oils represented by the tax gap on petrol and diesel. Energy companies face drastic economic and environmental challenges; therefore, this area necessarily requires the setting up of transparent economic instruments and, of course, production. The tax gap in VAT collection represents the gap between how much the state could potentially collect from VAT in accordance with the law and how much VAT really comes into the state coffers. The loss of tax revenues is caused by unpaid and undeclared tax liability. The Estimation of the Gap on Corporate Tax in Slovakia is a pilot project of the International Monetary Fund (IMF) in cooperation with the Institute for Financial Policy (IFP). The results present the estimation of the tax gap within a two-year delay. It is necessary to consider the estimation of the tax gap in the last two years as preliminary... [more]

In order to analyze the effects of various sizes of pyramid structure on solar cell characteristics, a pyramid structure was formed on the wafer through various etching processes. In this paper, etching was performed using one-step etching processes such as alkaline solution etching, reactive ion etching (RIE), and metal-assisted chemical etching (MACE), and two-step etching processes such as alkaline solution + MACE and alkaline solution + RIE. The micro-sized pyramid-structured wafers formed using the alkali solution showed higher reflectivity than nano-sized pyramid-structured wafers. Accordingly, it was expected that the characteristics of the cells fabricated with a nano-sized pyramid-structured wafer having low reflectivity would be higher than that of a micro-sized pyramid-structured wafer. However, it was confirmed that the quantum efficiency characteristics in the short wavelength region were higher in the micro-sized pyramid-structured wafers than in the nano-sized pyramid-st... [more]

The hotel sector is characterized by high thermal demands and a large carbon footprint, which greatly contributes to the global warming effect. Consequently, there is a need to investigate solutions that can reduce energy usage within this sector by means of environmentally friendly and sustainable technologies. Integrated CO2 heat pump systems for heating, cooling, and hot water production in hotels have demonstrated promising results. This paper theoretically compares the energy consumption, environmental impact, and cost of three different design concepts for integrated CO2 units equipped with thermal storage. The main characteristics of the evaluated designs are single-stage compression, parallel compression, and ejector-supported parallel compression. Furthermore, two separate hot water charging strategies were implemented and investigated over a large span of ambient temperatures and loads. The evaluations were carried out by considering eight different European locations, rangin... [more]

Organisations attempt to contribute their share towards fighting the climate crisis by trying to reduce their emission of greenhouse gases effectively towards net zero. An instrument to guide their reduction efforts is internal carbon pricing. Next to choosing the right pricing tool, defining the exact value of an internal carbon price, especially against the background of potential regulatory external carbon prices, and assessing its impact on business units’ energy systems poses a challenge for organisations. The academic literature has so far not examined the impact differences of an internal carbon price across different countries, which this paper addresses by using an optimisation model. First, it analyses the energy system cost increase of a real-world facility based on an internal carbon price compared to a potential regulatory carbon price within a country. Second, we evaluate the energy system cost increase based on an internal carbon price across different countries. The res... [more]

This paper examines the suitability of selected configurations of ultra-low voltage (ULV) oscillators as starters for a voltage boost converter to harvest energy from a thermoelectric generator (TEG). Important properties of particularly promising configurations, suitable for on-chip implementation are compared. On this basis, an improved oscillator with a low startup voltage and a high output voltage swing is proposed. The applicability of n-channel native MOS transistors with negative or near-zero threshold voltage in ULV oscillators is analyzed. The results demonstrate that a near-zero threshold voltage transistor operating in the weak inversion region is most advantageous for the considered application. The obtained results were used as a reference for design of a boost converter starter intended for integration in 180-nm CMOS X-FAB technology. In the selected technology, the most suitable transistor available with a negative threshold voltage was used. Despite using a transistor w... [more]

In terms of power and energy consumption, DRAMs play a key role in a modern server system as well as processors. Although power-aware scheduling is based on the proportion of energy between DRAM and other components, when running memory-intensive applications, the energy consumption of the whole server system will be significantly affected by the non-energy proportion of DRAM. Furthermore, modern servers usually use NUMA architecture to replace the original SMP architecture to increase its memory bandwidth. It is of great significance to study the energy efficiency of these two different memory architectures. Therefore, in order to explore the power consumption characteristics of servers under memory-intensive workload, this paper evaluates the power consumption and performance of memory-intensive applications in different generations of real rack servers. Through analysis, we find that: (1) Workload intensity and concurrent execution threads affects server power consumption, but a ful... [more]

Marine current power is a kind of renewable energy that has attracted increasing attention because of its abundant reserves, high predictability, and consistency. A marine current turbine is a large rotating device that converts the kinetic energy of the marine current into mechanical energy. As a straight-bladed vertical axis marine current turbine (VAMCT) has a square or rectangular cross-section, it can thus have a larger swept area than that of horizontal axis marine current turbines (HAMCT) for a given diameter, and also have good adaptability in shallow water where the turbine size is limited by both width and depth of a channel. However, the low energy utilization efficiency of the VAMCT is the main bottleneck that restricts its application. In this paper, two-dimensional numerical simulations were performed to investigate the effectiveness of an upstream deflector on improving performance of the straight-bladed (H-type) marine current turbine. The effects of various key geometr... [more]

The Yinggehai Basin is an important Cenozoic gas bearing basin in the South China Sea. With the gradual improvement of gas exploration and over-development in shallow layers, deep overpressured layers have become the main target for natural gas exploration. There are no large-scale faults in the strata above the Meishan Formation in the central depression, and hydraulic fracturing caused by overpressure in mudstone cap rocks is the key factor for the vertical differential distribution of gas. In this paper, based on the leak-off data, pore fluid pressure, and rock mechanics parameters, the Fault Analysis Seal Technology (FAST) method is used to analyze the hydraulic fracture risk of the main mudstones in the central depression. The results show that the blocks in the diapir zone have been subjected to hydraulic fracturing in the Huangliu cap rocks during the whole geological history, and the blocks in the slope zone which is a little distant from the diapirs has a lower overall risk of... [more]

A free-piston linear generator (FPLG) has a number of advantages compared to a traditional crank-slider internal combustion engine, including better thermal and mechanical efficiencies, different fuel compatibility, and a higher power-to-weight ratio. For electric vehicle propulsion and generation of portable power, an FPLG is a very attractive alternative source of energy. This paper presents the development of an FPLG simulation model using MATLAB-Simulink and investigates the impact of combustion variance on its operation. Results provided insight into various characteristics of system behavior through variation of structural dimension and operational parameters. In steady-state operation with fixed electrical load and fixed ignition for combustion, it was found that consecutively low combustion pressures can easily lead to engine stoppage, pointing to the significance of control for continuous operation. Due to the absence of the moment of inertia and flywheel character of the rota... [more]

A substantial share of the building sector in global energy demand has attracted scholars to focus on the energy efficiency of the building sector. The building’s energy consumption has been projected to increase due to mass urbanization, high living comfort standards, and, more importantly, climate change. While climate change has potential impacts on the rate of energy consumption in buildings, several studies have shown that these impacts differ from one region to another. In response, this paper aimed to investigate the impact of climate change on the heating and cooling energy demands of buildings as influential variables in building energy consumption in the city of Poznan, Poland. In this sense, through the statistical downscaling method and considering the most recent Typical Meteorological Year (2004−2018) as the baseline, the future weather data for 2050 and 2080 of the city of Poznan were produced according to the HadCM3 and A2 GHG scenario. These generated files were then u... [more]

In this paper, we consider the problem of state-of-charge estimation for rechargeable batteries. Coulomb counting is a well-known method for estimating the state of charge, and it is regarded as accurate as long as the battery capacity and the beginning state of charge are known. The Coulomb counting approach, on the other hand, is prone to inaccuracies from a variety of sources, and the magnitude of these errors has not been explored in the literature. We formally construct and quantify the state-of-charge estimate error during Coulomb counting due to four types of error sources: (1) current measurement error; (2) current integration approximation error; (3) battery capacity uncertainty; and (4) timing oscillator error/drift. It is demonstrated that the state-of-charge error produced can be either time-cumulative or state-of-charge-proportional. Time-cumulative errors accumulate over time and have the potential to render the state-of-charge estimation utterly invalid in the long term.... [more]

The efficiency of solar photovoltaic (PV) panels is greatly reduced by panel soiling and high temperatures. A mechanism for eliminating both of these sources of inefficiencies is presented by integrating solar PV generation with a compressed air system. High-pressure air can be stored and used to blow over the surface of PV panels, removing present dust and cooling the panels, increasing output power. A full-system mathematical model of the proposed system is presented, comprised of compressed air generation and storage, panel temperature, panel cleaning, and PV power generation. Simulation results indicate the benefit of employing compressed air for cleaning and cooling solar PV panels. For a fixed volume of compressed air, it is advantageous to blow air over the panels early in the day if the panel is soiled or when solar radiation is most abundant with the highest achievable flow rate if the panel is clean. These strategies have been shown to achieve the greatest energy captures for... [more]

As a highly nonlinear system, the performance of proton exchange membrane fuel cell (PEMFC) is controlled by various parameters. If the effects of all parameters are considered during the performance optimization, low working efficiency and waste of resources will be caused. The development of sensitivity analysis for parameters can not only exclude the parameters which have slight effects on the system, but also provide the reasonable setting ranges of boundary values for simulation of performance optimization. Therefore, sensitivity analysis of parameters is considered as one of the methods to optimize the fuel cell performance. According to the actual operating conditions of PEMFC, the fluctuation ranges of seven sets of parameters affecting the output performance of PEMFC are determined, namely cell operating temperature, anode/cathode temperature, anode/cathode pressure, and anode/cathode mass flow rate. Then, the control variable method is used to qualitatively analyze the sensit... [more]

This paper provides evidence on how the variability of the power produced by a wind farm and its revenue are affected by implementing a ramp-rate limitation strategy and by adding a storage device to the system. The wind farm receives penalties whenever the ramp-rate limitations are not respected and may be supported by batteries to avoid this scenario. In this paper, we model the battery usage as a discrete time homogeneous Markov chain with rewards thanks to which it is possible to simulate the state of the charge of the battery and to calculate the amount of penalties suffered by the wind farm during any period. An application is performed considering the power produced by a hypothetical wind turbine located in Sardinia (Italy) using real wind speed data and electricity prices from a period of 10 years. We applied the concept of ramp-rate limitation on our hourly dataset, studying several limitation scenarios and battery capacities.

The combustion characteristics of a staged combustion cycle engine with an oxidizer-rich preburner were experimentally studied at different momentum ratios of multi-element injectors. Propellants were simultaneously supplied as a liquid−liquid−liquid system, and an injector was designed in which a swirl coaxial jet is sprayed. The injector burned the propellants in the inner chamber which had a temperature greater than 2000 K. To cool the combustion gas, a liquid oxidizer was supplied to the cooling channel outside the injector. To prevent the turbine blades from melting, the temperature of the combustion gas was maintained below 700 K. To confirm the combustion characteristics at different momentum ratios of the high-temperature combustion gas inside the injector and the low-temperature liquid oxidizer outside the injector, three types of injectors were designed and manufactured with different momentum ratios: MR 3.0, MR 3.3, and MR 3.7. In this study, the results of the combustion te... [more]

Investor emotional heterogeneity and oil dual attributes are the key factors that cause the asymmetry of risks in the international crude oil market. This paper uses the monthly data from April 2003 to October 2020 to identify the dynamic characteristics of oil’s commodity attribute and financial attribute, and this paper also analyzes the asymmetric characteristics of risk evolution and risk degree in the international crude oil market under the condition of oil returns heterogeneity. The empirical results show that: first, there is heterogeneity in the influence of oil attributes on the risk evolution and risk degree of the international crude oil market; second, the alternation of oil dual attributes has a significant asymmetric impact on the risk evolution of international crude oil market; third, the sudden change of international crude oil market risk caused by oil attributes is asymmetric under different oil returns trends. Based on the empirical conclusion, this paper puts forw... [more]

Durability is the most pressing issue preventing the efficient commercialization of polymer electrolyte membrane fuel cell (PEMFC) stationary and transportation applications. A big barrier to overcoming the durability limitations is gaining a better understanding of failure modes for user profiles. In addition, durability test protocols for determining the lifetime of PEMFCs are important factors in the development of the technology. These methods are designed to gather enough data about the cell/stack to understand its efficiency and durability without causing it to fail. They also provide some indication of the cell/stack’s age in terms of changes in performance over time. Based on a study of the literature, the fundamental factors influencing PEMFC long-term durability and the durability test protocols for both PEMFC stationary and transportation applications were discussed and outlined in depth in this review. This brief analysis should provide engineers and researchers with a fast... [more]

This article discusses the work that resulted in the development of two battery-powered self-propelled electric mining machines intended for operation in the conditions of a Polish copper ore mine. Currently, the global mining industry is seeing a growing interest in battery-powered electric machines, which are replacing solutions powered by internal combustion engines. The cooperation of Mine Master, Łukasiewicz Research Network—Institute of Innovative Technologies EMAG and AGH University of Science and Technology allowed carrying out a number of works that resulted in the production of two completely new machines. In order to develop the requirements and assumptions for the designed battery-powered propulsion systems, underground tests of the existing combustion machines were carried out. Based on the results of these tests, power supply systems and control algorithms were developed and verified in a virtual environment. Next, a laboratory test stand for validating power supply syste... [more]

In Canada, more than 80% of energy in the residential sector is used for space heating and domestic hot water (DHW) production. This study aimed to model and compare the performance of four different systems, using solar energy as a renewable energy source for DHW production. A novel microchannel (MC) solar thermal collector and a microchannel-based hybrid photovoltaic/thermal collector (PVT) were fabricated (utilizing a microchannel heat exchanger in both cases), mathematical models were created, and performance was simulated in TRNSYS software. A water-to-water heat pump (HP) was integrated with these two collector-based solar systems, namely MCPVT-HP and MCST-HP, to improve the total solar fraction. System performance was then compared with that of a conventional solar-thermal-collector-based system and that of a PV-resistance (PV-R) system, using a monocrystalline PV collector. The heat pump was added to the systems to improve the systems’ efficiency and provide the required DHW te... [more]

A serious issue relative to the construction of electronic devices is proper power source selection. This problem is of particular importance when we are dealing with portable devices operating in varying environmental conditions, such as military equipment. A serious problem in the construction of electronic devices is the correct selection of the power source. In these types of devices, lithium-ion batteries are commonly used nowadays, and in particular their variety—lithium iron phosphate battery—LiFePO4. Apart from the many advantages of this type of battery offers, such as high power and energy density, a high number of charge and discharge cycles, and low self-discharge. They also have a major drawback—a risk of damage due to excessive discharge or overcharge. This article studies the process of charging and discharging a battery pack composed of cells with different initial charge levels. An attempt was made to determine the risk of damage to the cells relative to the difference... [more]

Hygrothermal modelling is increasingly used to inform building envelope design. A key input for these calculations is the material’s vapour diffusion properties. Respecting a growing international concern, this research has questioned the appropriateness of the current test method to establish construction material for vapour diffusion properties. This article reports on the empirical measurement of the vapour diffusion properties of two vapour-permeable building membranes commonly used in Australia residential systems when subjected to variable relative humidity conditions. The method involved completing dry cup and wet cup standard tests as specified in ISO 12572, (23 °C and 50% relative humidity RH). Further tests were then conducted as temperature remained at 23 °C but the relative humidity changed to 35%, 65% and 80%, respectively, in order to know if the diffusion properties are the same or change with varying relative humidity. The results from the wet cup and dry cup tests unde... [more]

When the shale gas reservoir is fractured, stress shadows can cause reorientation of hydraulic fractures and affect the complexity. To reveal the variation of stress shadow with perforation spacing, the numerical model between different perforation spacing was simulated by the extended finite element method (XFEM). The variation of stress shadows was analyzed from the stress of two perforation centers, the fracture path, and the ratio of fracture length to spacing. The simulations showed that the reservoir rock at the two perforation centers is always in a state of compressive stress, and the smaller the perforation spacing, the higher the maximum compressive stress. Moreover, the compressive stress value can directly reflect the size of the stress shadow effect, which changes with the fracture propagation. When the fracture length extends to 2.5 times the perforation spacing, the stress shadow effect is the strongest. In addition, small perforation spacing leads to backward-spreading... [more]