Molecular dynamics (MD) simulations were performed to investigate the nanoindentation behavior of Al/Mg-layered nanocomposites with varying layer thicknesses and Mg layer orientations in this study. The aim is to understand the weakening mechanisms at low layer thicknesses and the phase transition mechanisms associated with the dislocation slip angle in the Mg layer. Results indicate that the nanoindentation strength of nanocomposites increases with the layer thickness in the range of 1−10 nm, with the strength of 9.5 × 10−7 N at 10 nm being approximately 73% higher than that at 1 nm. This strength increase is mainly attributed to high interfacial stress, the higher percentage of amorphous atoms, weakened interatomic interactions, and the transition of adjacent interfaces to fully coherent interfaces that significantly reduce their ability to hinder dislocations at the low-layer thickness range. Additionally, in the initial deformation process, the hexagonal close-packed (HCP) phase of... [more]

The lithium storage performance of binary transition metal oxide/graphene composites as anode materials has been attracting more interest from researchers, based on the fact that binary transition metal oxides and graphene are expected to create a synergistic effect and exhibit improved lithium storage characteristics. In this work, a NiO-CuO/reduced graphene oxide composite (NiO-CuO/RGO) was prepared by an ultrasonic agitation process. When the NiO-CuO/RGO is applied to the anode material for lithium-ion batteries (LIBs), the batteries display high discharge capacities (at 730 mA h/g after 100 cycles at 100 mA/g), high-rate performance (311 mA h/g with 5000 mA/g), and excellent stable cyclability (375 mA h/g within 2000 mA/g after 400 cycles). Such results indicate that the combination of NiO-CuO and RGO leads to enhanced lithium storage performance, for the RGO sheets inhibit the large volume change of binary NiO-CuO and enhance the fast transport of both lithium ions and electrons d... [more]

Strawberry guava is the fruit of Psidium littorale, which grows in tropical regions. Few studies have examined the hydrophobic compounds and biological activities of this fruit. Therefore, we purified lipophilic compounds of strawberry guava and examined their effects on epidermal and blood vessel barrier functions as well as their anti-melanogenic activity. Lipophilic compounds were isolated by silica gel column chromatography followed by reversed-phase HPLC with MeOH from an EtOH extract of the fruit. Isolated compounds were identified by comparing NMR and MS spectra with those of reference values. The effects of these compounds on epidermal barrier function were evaluated by measuring transepidermal water loss (TEWL) using reconstructed human epidermal keratinocytes (RHEKs). Blood vessel barrier function was examined using dye permeability through human umbilical vein endothelial cell (HUVEC) layers. Anti-melanogenic activity was assessed by theophylline-induced melanogenesis in B16... [more]

Physicochemical properties of ionic liquids (ILs) are essential in solvent screening and process design. However, due to their vast diversity, acquiring IL properties through experimentation alone is both time-consuming and costly. For this reason, the creation of prediction models that can accurately forecast the characteristics of IL and its mixtures is crucial to their application. This study proposes a model for predicting the three important parameters of the IL-organic solvent−organic solvent ternary system: density, viscosity, and heat capacity. The model incorporates group contribution (GC) and machine learning (ML) methods. A link between variables such as temperature, pressure, and molecular structure is established by the model. We gathered 2775 viscosity, 6515 density, and 1057 heat capacity data points to compare the prediction accuracy of three machine learning methods, namely, artificial neural networks (ANNs), extreme gradient boosting (XGBoost), and light gradient boos... [more]

To overcome the challenges of feature selection in traditional machine learning and enhance the accuracy of deep learning methods for anomaly traffic detection, we propose a novel method called DCGCANet. This model integrates dilated convolution, a GRU, and a Channel Attention Network, effectively combining dilated convolutional structures with GRUs to extract both temporal and spatial features for identifying anomalous patterns in network traffic. The one-dimensional dilated convolution (DC-1D) structure is designed to expand the receptive field, allowing for comprehensive traffic feature extraction while minimizing information loss typically caused by pooling operations. The DC structure captures spatial dependencies in the data, while the GRU processes time series data to capture dynamic traffic changes. Furthermore, the channel attention (CA) module assigns importance-based weights to features in different channels, enhancing the model’s representational capacity and improving its... [more]

Nowadays, there has been a significant rise in the consumption of kefir, a functional beverage touted for its perceived health benefits. To offer a high-quality beverage to consumers, it is imperative to scrutinize and fine-tune the fermentation process. This study seeks to investigate the impact of fermentation time and the number of subcultures on the physicochemical, microbiological, and volatile composition, as well as the visual appearance, of kefir beverages obtained from four consecutive 24- or 48-h batch subcultures. All fermented beverages exhibited low lactose, ethanol and acids levels, with counts of viable probiotic lactic acid bacteria and yeast exceeding 106 colony forming units/mL. The four kefir beverages from the 48-h batch subcultures notably showed the lowest total concentrations of volatile compounds, likely due to overfermentation and over-acidification of the beverages. This caused the separation of the whey and curd, along with the formation of large gas bubbles,... [more]

Solid crystalline suspensions (SCSs) containing submicron particles were introduced as a competitive solution to increase dissolution rates and the bioavailability of poorly water-soluble drugs. In an SCS, poorly water-soluble drug crystals are finely dispersed in a hydrophilic matrix. Lately, melt milling as an adapted wet milling process at elevated temperatures has been introduced as a suitable batch manufacturing process for such a formulation. In this work, the transfer from batch operation to a two-step continuous process is demonstrated to highlight the potential of this technology as an alternative to other dissolution-enhancing methods. In the first step, a powder mixture of a model drug (griseofulvin) and a carrier (xylitol) is fed to an extruder, where a uniform suspension is obtained. In the second step, the suspension is transferred to a custom-built annular gap mill, where comminution down to the submicron region takes place. The prototype’s design was based on batch grin... [more]

Grapes and grape products are rich in secondary metabolites such as phenolic compounds and anthocyanins, which have antioxidant properties. These compounds possess health-promoting attributes, including cardioprotective, antimicrobial, and anticancer effects. In recent years, biotechnological methods have been employed to produce high quantities and purity of secondary metabolites under in vitro conditions, aiming to elucidate their complex functions and optimize production methods. However, the potential effects of harpin proteins on the accumulation of secondary compounds in callus cultures have not been investigated thus far. Harpin proteins, encoded by the hrp gene clusters in Gram-negative phytopathogens, are known to trigger defense responses in various plant species by promoting the accumulation of secondary compounds. These findings suggest that harpin proteins may have the potential to enhance secondary metabolite accumulation in callus cultures. This study therefore investiga... [more]

To realize a quantitative diagnosis of faults in the planetary gearboxes of wind turbines by processing the complex frequency signals of the planetary gear boxes and avoiding the aliasing problem of the resulting frequencies, this paper proposes a diagnosis method based on improved variational mode decomposition (IVMD) and average multi-scale double symbolic dynamic entropy (AMDSDE). Moreover, an IVMD algorithm based on multi-scale permutation entropy is introduced to reduce noise interference and realize signal demodulation. Considering the effects of complex transfer paths and the correlation between current and adjacent state modes, AMDSDE is proposed. Each fault size is obtained based on the entropy curve, and the AMDSDE of unknown faults is calculated. To verify the accuracy of the proposed method, simulations and experimental signals are processed. The quantitative diagnosis of the planetary gearboxes of wind turbines is realized, providing a reliable basis for evaluating the hea... [more]

The present work focuses on predicting the steel melt temperature following the vacuum treatment step in a vacuum tank degasser (VTD). The primary objective is to establish a comprehensive methodology for developing and validating machine learning (ML) models within this context. Another objective is to evaluate the model by analyzing the alignment of the SHAP values with metallurgical domain expectations, thereby validating the model’s predictions from a metallurgical perspective. The proposed methodology employs a Random Forest model, incorporating a grid search with domain-informed variables grouped into batches, and a robust model-selection criterion that ensures optimal predictive performance, while keeping the model as simple and stable as possible. Furthermore, the Shapley Additive Explanations (SHAP) algorithm is employed to interpret the model’s predictions. The selected model achieved a mean adjusted R2 of 0.631 and a hit ratio of 75.3% for a prediction error within ±5 °C. De... [more]

Transient heat conduction and mass transfer have many applications in industry such as heating, cooling, cooking, quenching of steels, freezing, and convective drying of vegetables or fruits. A novel, interactive, and fast MATLAB application, named MULTITHMT, is improved to solve multidimensional transient heat and mass transfer problems. Exact solutions are obtained for infinite rectangular bars, short cylinders, rectangular prisms, and spherical geometries. Instantaneous temperature and moisture content at any location in the objects are obtained and temperature and moisture content at the final time are displayed in two- and three-dimensional graphics. Quenching of steel for rectangle bars and cooking of cylindrical or rectangular prism-shaped meat are represented for transient heat transfer. Cooling of spherical commercial bronze and iron is also investigated. For transient mass transfer, convective drying of rectangular prunes, bananas of short cylinders, and spherical cornelian c... [more]

Recently, scientists have been developing sustainable processes, and in this context, mechanochemistry is commonly associated with green chemistry for its ability to reduce waste generation from chemical reactions. The well-known acetate complex, diacetate bis(triphenylphosphine) ruthenium(II) [Ru(OAc)2(PPh3)2], is a versatile precursor for preparing active complexes for several catalytic reactions. This report presents an efficient and straightforward manual grinding protocol for the sustainable synthesis of ruthenium carboxylate complexes starting from the commercially available [RuCl2(PPh3)3] and metal carboxylates. This work represents a novel and preliminary investigation into carboxylate precursors’ alternative solventless synthesis route based on manual grinding. To our knowledge, this is the first time [Ru(OAc)2(PPh3)2] has been prepared via a mechanochemical procedure. The synthesis method has also been investigated for other alkali metal carboxylates and yields ranging from 3... [more]

In a hydropower station, equipment needs maintenance to ensure safe, stable, and efficient operation. And the essence of equipment maintenance is a disassembly sequence planning problem. However, the complexity arises from the vast number of components in a hydropower station, leading to a significant proliferation of potential combinations, which poses considerable challenges when devising optimal solutions for the maintenance process. Consequently, to improve maintenance efficiency and decrease maintenance time, a discrete whale optimization algorithm (DWOA) is proposed in this paper to achieve excellent parallel disassembly sequence planning (PDSP). To begin, composite nodes are added into the constraint relationship graph based on the characteristics of hydropower equipment, and disassembly time is chosen as the optimization objective. Subsequently, the DWOA is proposed to solve the PDSP problem by integrating the precedence preservative crossover mechanism, heuristic mutation mech... [more]

The widely used discrete-element particle flow software PFC’s (PFC 7.0 and previous versions) algorithm for calculating porosity is not sufficiently accurate. Because of this, when the particles are densely packed, the solution to the equation produces an algorithm exception for odd calculations of porosity, which results in the inability to calculate the results. This paper, based on a Darcy seepage model of fluid flow through a granular bed, analyzed the shortcomings of the two porosity calculation methods of PFC and the function analysis method. Combining this analysis with the theory of computer graphics, a new and efficient porosity calculation algorithm was proposed. The result showed that the new proposed porosity calculation algorithm calculated a more accurate and reasonable porosity field and made the iterative solution of the CFD equation more stable. This method makes porosity-related models of PFC more accurate. The algorithm can be not only used to calculate porosity, but... [more]

With the rapid development of industrialization, the problem of concentration determination based on the copper production process has been widely concerned, and the accurate determination of high-concentration copper ions (Cu2+) is of great significance for enterprise production, resource utilization, and pollution prevention. The characteristics of different spectrophotometric methods for the determination of Cu2+ are discussed, and it is found that these methods are suitable for the determination of trace or low concentration of Cu2+ (0.5 μg/L−5 mg/L), whereas for the determination of high Cu2+ concentration pre-treatments such as dilution, complexation, and coloring are required. In this study, a method based on ultraviolet-visible spectroscopy (UV-Vis) combined with partial least squares regression analysis (PLS) was proposed for the determination of high copper ions (>100 mg/L), which performs rapid and accurate determination of high Cu2+ concentration by preprocessing and featur... [more]

Reverse electrodialysis (RED) is one of the methods able to generate energy from the salinity gradient between sea- and river water. The technique is based on the diffusion of ions through membranes that specifically allow either cations or anions to pass through. This ion current is converted into an external electric current at electrodes via suitable redox reactions. Seawater contains mainly eight different ions and the description of transport phenomena in membranes in classical terms of isolated species is not sufficient because the different particles have different velocities—in the same direction or opposite—in the same membrane. More realistic is the Maxwell−Stefan (MS) theory that takes all interactions between the different particles in account; however, such a model is complex and validation is difficult. Therefore, a simplified system is used with solely NaCl in solution, using only 9 diffusivities in the calculation. These values are estimated from the literature and are... [more]

Reservoir damage is a key factor affecting reservoir evaluation, ensuring stable reservoir production and improving the utilization rate of oil and gas resources. At present, the evaluation of damage caused by reservoir drilling fluid is too empirical, and there is a lack of methods for the high-precision evaluation of reservoir damage after drilling fluid invasion and pollution. In a block in the East China Sea, the production capacity is limited due to an excessive balance of drilling fluid and long exposure time. In order to ensure safe drilling, the dynamic damage mechanism of drilling fluid during drilling was analyzed. The core of the main reservoir of well XH-1 in a block in the East China Sea was selected for carrying out an experiment evaluating the dynamic damage caused by drilling fluid. According to the experimental results, the damage rate of reservoir permeability caused by drilling fluid invasion ranges between 58.25 and 87.25%, and the overall dynamic damage degree can... [more]

Non-thermal plasma (NTP) conversion applications have become an emerging technology of increasing global interest due to their particular ability to perform at atmospheric pressure and ambient temperature. This study focuses on a specific case of a dielectric barrier discharge NTP reactor for carbon dioxide conversion with the usage of argon as diluent gas. The plasma computations in COMSOL® Multiphysics are compared to experimental results and coupled with previous thermodynamic characterization of argon species and fluid dynamic calculations. The model is defined as a time-dependent study with a 2D-Geometry of pure argon, with both fluid flow and plasma phenomena. Firstly, the model showcases an accurate understanding of the plasma physics involved, in the form of electron density, excited argon, argon ions, and mean electron energy. It also allows a direct comparison of the velocity, vorticity, pressure, and dynamic viscosity results with fluid flow computations. Secondly, the impac... [more]

Excessive alcohol intake leads to significant physiological complications, particularly alcoholic liver diseases (ALD). The extent of liver damage caused by ethanol correlates with increased oxidative stress and accumulation of lipids in the hepatic tissue. In this study, we investigated the defense properties of the aqueous extract of Perilla frutescens Briton Var. acuta Kudo (PF) on hepatic injury in chronically ethanol-treated mice. The mice were orally administered the water extract from PF for 4 weeks with ethanol treatment (3 g/kg. P.O.). The level of malondialdehyde (MDA) in the liver tissues was determined. A substantial increase in MDA generation was detected in the livers of mice subjected to ethanol exposure, whereas the administration of PF markedly reduced MDA levels in hepatic tissues. Additionally, histological analysis of the liver tissue was performed. Histopathological investigation revealed a significant reduction in hepatocellular necrosis in the PF-treated group. T... [more]

The Processes Editorial Office retracts the article titled “RETRACTED: In-Situ Yeast Fermentation Medium in Fortifying Protein and Lipid Accumulations in the Harvested Larval Biomass of Black Soldier Fly” [...]

The transient temperature of the wellbore plays an important role in the selection of downhole tools during the drilling of deep shale gas horizontal wells. This study established a transient temperature field model of horizontal wells based on the convection heat transfer between wellbore and formation and the principle of energy conservation. The model verification shows that the root mean squared error (RMSE) between the measured annular temperature neat bit and the predicted value is 0.54 °C, indicating high accuracy. A well in Chongqing, China, is taken as an example to study the effects of bottom hole assembly (BHA), drill pipe size, drilling fluid density, flow rate, inlet temperature of drilling fluid, and drilling fluid circulation time on the temperature distribution in wellbore annulus. It is found that the increase in annular temperature is about 1 °C/100 m in the horizontal section when a positive displacement motor (PDM) is used. A Φ139.7 mm drill pipe is more favorable f... [more]

Microplastics, primarily derived from plastic waste, are pervasive environmental pollutants found across aquatic and terrestrial ecosystems. This review investigates microplastics’ presence, distribution, and impacts in marine ecosystems, with a particular focus on fish species. Research indicates that microplastics are present in various anatomical parts of fish, including the gastrointestinal tracts and gills, with significant implications for marine biodiversity and human health through seafood consumption. The review also highlights the sources of microplastics, such as synthetic textiles, packaging, and personal care products, and explores the pathways through which these particles enter marine environments. Advanced detection techniques have identified microplastics in human tissues, underscoring the urgency of addressing this environmental threat. Comprehensive strategies are essential to mitigate microplastic pollution and protect both marine life and human health.

Herein, the Aspen models to the paper "Chemical recycling of plastic waste via production of ethylene from gasification syngas" are published. The model starts at syngas, as gasification was not modeled in Aspen Plus. Syngas is treated and fed into a methanation reactor. Ethylene is then produced via oxidative coupling of methane. The fractionation involves cryogenic distillation as well as CO2 capture. Latter one was modeled in a separate file.

Sugarcane accounts for around 80% of global sugar production. However, the sugar industry is known for producing significant amounts of organic wastewater with a high COD (5000−8000 mg/L) that severely pollutes the environment. A lab-scale trial was conducted to evaluate the efficacy of a horizontal subsurface flow wetland planted with Typha latifolia and Phragmites australis in removing pollutants from sugar industry wastewater. The wetland system was subjected to rigorous testing, operating at a high flow rate of 2.166 gallons per day and exposed to a high organic loading rate (3800 mg/L COD and 2470 mg/L BOD), as well as elevated levels of inorganic nitrogen, sulfate, and phosphate (100 mg/L, 80 mg/L, and 10 mg/L, respectively). Our findings indicate significant removal efficiencies, with the wetland system achieving removal rates of 88% for COD, 97% for BOD, 96% for total nitrogen, and 95% for sulfate. Remarkably, the system exhibited enhanced removal efficiency when exposed to dom... [more]

To uncover the reservoir characteristics and enrichment law of coal-measure gas in Julu sag, Hebei Province, and achieve co-exploration and co-mining, it is necessary to conduct a comprehensive analysis. In this study, we investigated the characteristics of coal-measure gas accumulation in the Taiyuan Formation and Shanxi Formation in the Julu area. This was achieved by collecting data on coal-measure source rocks and organic geochemistry, which were then combined with regional geological conditions. This study indicates that the coal seams and shales of Shanxi Formation and Taiyuan Formation in the study area serve as the primary source rocks. The predominant macerals found in coal rock are vitrinite. Furthermore, the organic matter type present in shale is primarily categorized as type II2, with the organic matter maturity falling within the immature−mature stage. Based on the simulation results of tectonic-burial history, thermal evolution history, and hydrocarbon generation history... [more]