A concentric annular heat pipe heat sink (AHPHS) was proposed and fabricated to investigate its thermal behavior. The present AHPHS consists of two concentric pipes of different diameters, which create vacuumed annular vapor space. The main advantage of the AHPHS as a heat sink is that it can largely increase the heat transfer area for cooling compared to conventional heat pipes. In the current AHPHS, condensation takes place along the whole annular space from the certain heating area as the evaporator section. Therefore, the whole inner space of the AHPHS except the heating area can be considered the condenser. In the present study, AHPHSs of different diameters were fabricated and studied experimentally. Basic studies were carried out with a 50 mm-long stainless steel AHPHS with diameter ratios of 1.1 and 1.3 and the same inner tube diameter of 76 mm. Several experimental parameters such as volume fractions of 10−70%, different air flow velocity, flow configurations, and 10−50 W heat... [more]

Power plants based on organic Rankine cycle (ORC) are known for their capacity in converting low and medium-temperature energy sources to electricity. To find the optimal operating conditions, a designer must evaluate the ORC from different perspectives including thermodynamic performance, technological limits, economic viability, and environmental impact. A popular approach to include different criteria simultaneously is to formulate a bi-objective optimization problem. This type of multi-objective optimization (MOO) allows for finding a set of optimal design points by defining two different objectives. Once the optimization is completed, the decision-making analysis shall be carried out to identify the final design solution. This study aims to develop a decision-making tool for facilitating the choice of the optimal design point. The proposed procedure is coded in MATLAB based on the commonly used Technique for Order Preference by Similarity to Ideal Solution (TOPSIS). By providing t... [more]

This paper presents a real-time dispatch strategy for coupled transmission and distribution systems within a distributed and cooperative control framework to maintain reliable and secure operation with minimum generation costs and maximum renewable energy consumption. The presented strategy transforms each distribution system into a dispatchable active source via an average-consensus-based active power control of renewable distributed energy resources (DERs) at the distribution level and then dispatches the active power reference of conventional generators as well as the distribution systems in a measurement-based way at a transmission level. The voltage fluctuation caused by the DER active power control is smoothened with a distributed voltage control method, which can also reduce the active power loss in the distribution systems. Compared to existing real-time dispatch strategies, the proposed strategy can eliminate security issues in the transmission system in a short time by regula... [more]

Because traditional electronics cannot directly use the alternating output voltage and current provided by electric field energy harvesters, harvesting systems require additional regulating and conditioning circuits. In this field, this work presents a conditioning circuit, called serial switch-only rectifier (SSOR) for low-voltage electric field energy harvesting (EFEH) applications. The proposed approach consists of a tubular topology harvester mounted on the outer jacket of a 230 V three-wires electrical cable (neutral, ground, and phase), in which terminals are connected to SSOR. We compare SSOR performance with classic electronic approaches, such as a full-bridge rectifier and voltage doubler. Experimental findings showed that the gathered energy by a 1 m cylindrical harvester increased in approximately 73.3% using the SSOR as a power management circuit. Experimental findings showed that the gathered energy by a 1 m cylindrical harvester increase in approximately 73.3% using the S... [more]

Hydraulic fracturing becomes an essential method to develop tight gas. Under high injection pressure, fracturing fluid entering into the formation will reduce the flow channel. To investigate the influence of water saturation on gas flow behavior, this study conducted the gas relative permeability with water saturation and the flow rate with the pressure gradient at different water saturations. As the two dominant tight gas-bearing intervals, the Upper Paleozoic Taiyuan and Shihezi Formations deposited in Ordos Basin were selected because they are the target layers for holding vast tight gas. Median pore radius in the Taiyuan Formation is higher than the one in the Shihezi Formation, while the most probable seepage pore radius in the Taiyuan Formation is lower than the one in the Shihezi Formation. The average irreducible water saturation is 54.4% in the Taiyuan Formation and 61.6% in the Shihezi Formation, which indicates that the Taiyuan Formation has more movable water. The average... [more]

This study focuses on determining the impacts and potential value of unmanaged and managed uni-directional and bi-directional charging of plug-in electric vehicles (PEVs) to integrate intermittent renewable resources in California in the year 2030. The research methodology incorporates the utilization of multiple simulation tools including V2G-SIM, SWITCH, and GridSim. SWITCH is used to predict a cost-effective generation portfolio to meet the renewable electricity goals of 60% in California by 2030. PEV charging demand is predicted by incorporating mobility behavior studies and assumptions charging infrastructure and vehicle technology improvements. Finally, the production cost model GridSim is used to quantify the impacts of managed and unmanaged vehicle-charging demand to electricity grid operations. The temporal optimization of charging sessions shows that PEVs can mitigate renewable oversupply and ramping needs substantially. The results show that 3.3 million PEVs can mitigate ove... [more]

Renewable energy (RE) utilization is expected to increase in the coming years due to its decreasing costs and the mounting socio-political pressure to decarbonize the world’s energy systems. On the other hand, lithium-ion (Li-ion) batteries are on track to hit the target 100 USD/kWh price in the next decade due to economy of scale and manufacturing process improvements, evident in the rise in Li-ion gigafactories. The forecast of RE and Li-ion technology costs is important for planning RE integration into existing energy systems. Previous cost predictions on Li-ion batteries were conducted using conventional learning curve models based on a single factor, such as either installed capacity or innovation activity. A two-stage learning curve model was recently investigated wherein mineral costs were taken as a factor for material cost to set the floor price, and material cost was a major factor for the battery pack price. However, these models resulted in the overestimation of future pric... [more]

Calculation models for the selection of cable lines used for expansion and modernization in the energy system and energy transmission planning are recognized tools supporting decision-making in both the energy sector and energy policy. At the same time, the above calculation models contain a large number of correction factors taking into account the temperature of the external environment at various points, the mutual influence of which is not taken into account. This means limitations to today’s common approaches to solutions, especially with regard to the required safety buffer for cable line selection. To meet this challenge, this article presents a parameter that takes into account the change and difference in temperature at various points in the external environment in the analyzed cable line systems. The purpose of this paper was to develop a new approach to the selection of a cable line in order to minimize failure during operation. For this purpose, possible temperature cases t... [more]

A laboratory-scale analysis using coal from an underground mine was carried out, emulating a mixture from the gob area in an actual mine, consisting of waste, coal, and free space for the flow of air. Experimental tests and computational fluid dynamics modelling were done to define and verify the behavior of the collapsed region in a time-dependent analysis. In addition, the characteristics of coal were defined, regarding the self-combustion, combustion rate, and pollutants generated in each stage of the fire. The results achieved are useful for determining the behavior of the collapsed area in full-scale conditions and to provide valuable information to study different scenarios of a potential fire in a real sublevel coal mine regarding how the heat is spread in the gob and how pollutants are generated.

Types of tapered piles are widely applied in tank foundation consolidation, but their inherent deficiencies in design and construction limit their further promotion. Vortex compression pile is a novel nodular pile. Compared with the traditional equal-section pile, vortex compression nodular pile is featured by stronger bearing capacity and slighter settlement. In this paper, the model test results showed that vortex compression nodular pile can greatly improve the bearing capacity and reduce the settlement. Through the finite element software ABAQUS analysis the bearing characteristics of equal-section pile foundation and vortex-compression nodular pile foundation were compared. The three-dimensional solid model was established by ABAQUS finite element software. The impact of cushion modulus, cushion thickness, vertical load, pile modulus, soil modulus around the pile on the bearing capacity of the vortex-compression nodular pile foundation were studied.

Economic and social progress is directly and closely related to energy consumption. In the latest decades, there is a higher need to reduce energy consumption from conventional sources, replacing it with energy obtained from unconventional sources. The environmental concern is one of the objectives of the European economic policy, with a particular focus on renewable energy consumption and energy efficiency in order to lower the environmental impact. In this context, we analyzed energy consumption per capita and renewable energy consumption per capita in the EU with the help of parametric methods, using the β-convergence model, and semiparametric methods, using the σ-convergence model. In this research we proposed to study six analysis models of the period 1960−2015, based on the availability of data. We concluded that the EU states went through a convergence process in a slow pace of energy consumption per capita and renewable energy per capita, showing a convergence pattern. The resu... [more]

Global deposits of concentrated phosphates, which are a necessary source for the production of phosphate fertilizers, are limited. These reserves keep getting thinner, and every day, large amounts of phosphorus end up in watercourses. In this study, we verified that modified biochar (saturated with FeCl3 solution and then neutralized with NaOH solution) can adsorb significant amounts of phosphorus from wastewater. Moreover, the agrochemical qualities of sludge water from a municipal wastewater treatment plant, struvite, phosphorus-saturated biochar, and iron(III) phosphate from a reused biochar filter were tested in this study. We determined the amount of mobile phosphorus as well as the amount of extractable phosphorus and its five fractions. It was found that modified biochar can hold one-third of the phosphorus amount contained in the commonly used agricultural fertilizer simple superphosphate (1 × 105 g of modified biochar captures up to 2.79 × 103 g of P). Moreover, plants can mor... [more]

Frequent working condition conversions in pumped-storage power stations often induce stability problems, especially when the operating point enters the S-shaped region, during which flow transitions and pressure fluctuations are serious. The pump-turbines with different specific speed values show different characteristics, but their differences in stability features are still not clear. In this study, four different pump-turbines were selected to simulate the runaway processes from turbine modes. The similarities and differences of flow patterns and pressure fluctuations were analyzed. For the similarities, pressure pulsations increase gradually and fluctuate suddenly once the backflows occur at the runner inlets. For the differences, the evolutions of backflows and pressure pulsations are related to specific speeds and runner shapes. Firstly, it is easier for the lower specific speed turbines to enter the reverse pump mode. Secondly, the blade lean angle influences the position where... [more]

An automatic stage transition converter for an inductive power transfer system is presented in this paper. An effective control strategy with two working stages of independent energy injection stage and free resonance stage is employed in the proposed converter. With the automatic stage transition strategy, when the frequency of the resonance network changes, the ending time of the free resonance stage is automatically determined. At the same time, the phase angle of the free resonance stage is automatically set as half a resonant cycle. As the stage transition is not triggered by the switches, the switch motion can be executed in advance of the transition moments. Time margins are offered for every switch in the converter, which make the switching moments of the switches flexible and the control simple. Another feature of this converter is that during the energy injection stage, the energy is injected into the inductor independently. Therefore, the input power can be easily regulated... [more]

Increasing the biodiesel content of diesel fuels is encouraged because of its reduced carbon footprint. Pure rapeseed methyl ester (RME)and used cooking oil methyl ester (UCOME) are characterised by well-to-tank greenhouse gas (GHG) reductions of 54% and 88% compared to pure B0 petrodiesel, respectively. Captive fleets such as public transport buses could benefit from these GHG reductions by increasing the biodiesel content of their fuel because they have a consequent yearly fuel consumption. The aim of this paper is to compare on-road tailpipe emissions of a diesel bus when increasing the biodiesel concentration in the fuel. The tests were carried out on a standard city bus belonging to the Euro V EEV emission standard that was equipped with a portable emission measurement system measuring NO, NO2, PN, CO and CO2 at the tailpipe. The bus followed the SORT which is representative of urban bus driving. The heavy urban on-road measurements indicated increased NOx emissions (24−26%), decr... [more]

In recent years, environmental concerns resulted in an increase in the use of renewable resources such as wind energy. However, high penetration of the wind power is a challenge due to the intermittency of this resource. In this context, the wind energy forecasting has become a major issue. In particular, for the end users of wind energy forecasts, a critical but often neglected issue is the economic value of the forecast. In this work, we investigate the economic value of forecasting from 30 min to 3 h ahead, also known as nowcasting. Nowcasting is mainly used to inform trading decisions in the intraday market. Two sources of uncertainty affecting wind farm revenues are investigated, namely forecasting errors and price variations. The impact of these uncertainties is assessed for six wind farms and several balancing strategies using market data. Results are compared with the baseline case of no nowcasting and with the idealized case of perfect nowcast. The three settings show signific... [more]

The present study developed a new system of electrochemical water splitting using a boron doped diamond (BDD) electrode in the electrochemical reactor. The new method assessed the electrical current, acidity (pH), electrical conductivity, absorbance, dissipation, and splitting energies in addition to the water splitting efficiency of the overall process. Employing CuO NPs and ZnO NPs as catalysts induced a significant impact in reducing the dissipated energy and in increasing the efficiency of splitting water. Specifically, CuO NPs showed a significant enhancement in reducing the dissipated energy and in keeping the electrical current of the reaction stable. Meanwhile, the system catalyzed with ZnO NPs induced a similar impact as that for CuO NPs at a lower rate only. The energy dissipation rates in the system were found to be 48% and 65% by using CuO and ZnO NPs, respectively. However, the dissipation rate for the normalized system without catalysis (water buffer at pH = 6.5) is known... [more]

Turnouts are key parts of rail roads and are exposed to adverse weather conditions such as snowfall, snow drifts, low temperatures, or sleet. Effective protection assures good turnout function and contributes to rail traffic efficiency and safety. Presently, resistance heating (RH) is the most common system of turnout heating in Europe. In this study, we attempted to implement energy-saving induction heating (IH) in order to cut costs of operation and electricity. A turnout heating test stand, including a stock-rail and a switch-rail, was executed in a climatic chamber. Air temperature was constant at the time of heating. Active power received by both the systems was identical for any measurement (450 W). Test results enabled an assessment of switch-rail position and variations of climatic chamber air temperature on growth of turnout temperatures. Effects of heating type on correct lubrication of the slide plate surface were compared. Dynamics of heating variations and their impact on... [more]

Growth in application fields of unmanned aerial vehicles (UAVs) and an increase in their total number are followed by higher and higher expectations imposed on improvements in UAV propulsion and energy management systems. Most commercial vertical takeoff and landing (VTOL) UAVs employ a constant pitch propeller that forces a mission execution tradeoff in the majority of cases. An alternative solution, presented here, consists of the use of a variable pitch propeller. The paper summarizes experimental measurements of the propulsion system equipped with an innovative variable pitch rotor. The investigations incorporated characteristics of the rotor for no wind conditions and a new approach to optimize pitch settings in hover flight as a function of UAV weight and energy consumption. As UAV battery capacity is always limited, efficient energy management is the only way to increase UAV mission performance. The study shows that use of a variable pitch propeller can increase the maximal take... [more]

Airports, broadly spread world-wide, present continuously increasing energy demands for heating and cooling purposes. Relocatable facilities within them could be built on recycling shipping containers provided with the right insulation layer, to reduce the outstanding consumption of the heating, ventilation and air conditioning systems (HVAC). This research focuses on studying the effect of added insulation on the thermal performance of a construction in the scope of an airport facility, based on a recycled shipping container. Passive heating and cooling insulation strategies have shown good results in terms of energy savings. A series of simulations were performed along six different Spanish airports locations, selected to represent several climate conditions. Temperature evolution inside the container, and energy demands of the HVAC system were obtained to show that the insulation provided by phase change materials (PCM) is performing better than traditional insulation, or a raw cont... [more]

This paper presents the results of an interdisciplinary study aimed at assessing the possibility of using duckweed to purify and recover nutrients from the effluent remaining after struvite precipitation and ammonia stripping from a liquid fraction of anaerobic digestate in a biorefinery located at a Dutch dairy cattle production farm. The nutritional value of duckweed obtained in a biorefinery was assessed as well. Duckweed (Lemna minuta) was cultured on a growth medium with various concentrations of effluent from a biorefinery (EFL) and digested slurry (DS) not subjected to the nutrient recovery process. The study’s results showed that duckweed culture on the media with high contents of DS or EFL was impossible because they both inhibited its growth. After 15 days of culture, the highest duckweed yield was obtained from the ponds with DS or EFL contents in the medium reaching 0.39% (37.8 g fresh matter (FM) and 16.8 g FM per 8500 mL of the growth medium, respectively). The recovery o... [more]

The purpose of this study is to reduce the risk of leakage of CO2 geological storage by injecting the dissolved CO2 solution instead of the supercritical CO2 injection. The reservoir simulation method is used in this study to evaluate the contributions of the different trapping mechanisms, and the safety index method is used to evaluate the risk of CO2 leakage. The function of the dissolved CO2 solution injection is performed by a case study of a deep saline aquifer. Two scenarios are designed in this study: the traditional supercritical CO2 injection and the dissolved CO2 solution injection. The contributions of different trapping mechanisms, plume migrations, and the risk of leakage are evaluated and compared. The simulation results show that the risk of leakage via a natural pathway can be decreased by the approach of injecting dissolved CO2 solution instead of supercritical CO2. The amount of the CO2 retained by the safe trapping mechanisms in the dissolved CO2 solution injection s... [more]

As renewable energy resources such as wind and solar power are developing and the penetration of electric vehicles (EVs) is increasingly integrated into existing systems, uncertainty and variability in power systems have become important issues. The charging demands for EVs and wind power output are recognized as highly variable generation resources (VGRs) with uncertainty, which can cause unexpected disturbances such as short circuits. This can deteriorate the reliability of existing power systems. In response, research is required to identify the uncertainties presented by VGRs and is required to examine the ability of power system models to reflect those uncertainties. The deterministic method, which is the most basic method that is currently in use, does not reflect the uncertainty of system components. Therefore, this paper proposes a probabilistic method to assess the steady-state security of power systems, reflecting the uncertainty of VGRs using Monte Carlo simulation (MCS). In... [more]

This paper proposes that the scope of research should be extended to the whole clinker calcination system from its single device or specific process (i.e., its functional subunits) as conventionally conducted. Mass/heat flow and effective heat were first analyzed to obtain the thermal efficiencies of its subunits (φi); a thermal efficiency model of the whole system φQY was thus established by correlating the relationship between φi and φQY. The thermal efficiency model of the whole system showed that φi had a positive linear correlation with φQY; it was found that the thermal efficiency of the decomposition and clinker calcination unit (φDC) had the greatest weight on φQY, where a 1% increase in φDC led to a 1.73% increase in φQY—improving φDC was shown to be the most effective way to improve φQY. In this paper, the developed thermal efficiency model was applied to one 5000 MT/D production line. It was found that its φQY was only 61.70%—about 2.35% lower than a representative line; suc... [more]

Solar irradiance prediction is significant for maximizing energy-saving effects in the predictive control of buildings. Several models for solar irradiance prediction have been developed; however, they require the collection of weather data over a long period in the predicted target region or evaluation of various weather data in real time. In this study, a long short-term memory algorithm−based model is proposed using limited input data and data from other regions. The proposed model can predict solar irradiance using next-day weather forecasts by the Korea Meteorological Administration and daily solar irradiance, and it is possible to build a model with one-time learning using national and international data. The model developed in this study showed excellent predictive performance with a coefficient of variation of the root mean square error of 12% per year even if the learning and forecast regions were different, assuming that the weather forecast was correct.