Based on low-cost and easy to enlarge, the bubble column device has been widely concerned in chemical industry. This paper focuses on bubble plumes in laboratory-scale three-dimensional rectangular air-water columns. Static behavior has been investigated in many experiments and simulations, and our present investigations consider the dynamic behavior of bubble plume offset in three dimensions. The investigations are conducted with a set of closure models by the Euler−Euler approach, and subsequently, literature data for rectangular bubble columns are analyzed for comparison purposes. Moreover, the transient evolution characteristics of the bubble plume in the bubble column and the gas phase distribution in sections are introduced, and the offset characteristics and the oscillation period of the plume are analyzed. In addition, the distributions of the vector diagram of velocity and vortex intensity in the domain are given. The effects of different fluxes and column aspect ratios on bub... [more]

Multi-stage flash (MSF) desalination plays an important role in achieving large-scale fresh water driven by thermal energy. In this paper, based on first-principle modeling of a typical multi-stage flash desalination system, the effects of different operational parameters on system performance and operational optimization for cost saving were extensively studied. Firstly, the modelled desalination system was divided into flash chamber modules, brine heater modules, mixed modules and split modules, and based on energy and mass conservation laws the equations were formulated and put together to describe the whole process model. Then, with physical parameter calculation the whole process was simulated and analyzed on the platform of MATLAB, and the water production performance effected by operational parameters such as the feed temperature of seawater, the recycle brine from the discharge section, steam temperature and flowrate of recycled brine were discussed and analyzed. Then, the opti... [more]

The need for miniaturised reaction systems has led to the development of various microreactor platforms, such as droplet-based microreactors. However, these microreactors possess inherent drawbacks, such as rapid evaporation and difficult handling, that limit their use in practical applications. Liquid marbles are droplets covered with hydrophobic particles and are a potential platform that can overcome the weaknesses of bare droplets. The coating particles completely isolate the interior liquids from the surrounding environment, thus conveniently encapsulating the reactions. Great efforts have been made over the past decade to demonstrate the feasibility of liquid marble-based microreactors for chemical and biological applications. This review systemically summarises state-of-the-art implementations of liquid marbles as microreactors. This paper also discusses the various aspects of liquid marble-based microreactors, such as the formation, manipulation, and future perspectives.

Electrolyzed water (EW) shows great potential as a green and economical sanitation solution for the food industry. However, only limited studies have investigated the optimum electrolysis parameters and the bactericidal effect of acidic electrolyzed water (AcEW) and alkaline electrolyzed water (AlEW). Here, the Box−Behnken experimental design was used to identify the optimum parameters. The tests were conducted with different types of electrodes, electrical voltages, electrolysis times, and NaCl concentrations. There were no obvious differences observed in the physico-chemical properties of EW when different electrodes were used. However, stainless steel was chosen as it meets most of the selection criteria. The best-optimized conditions for AcEW were at 11.39 V, 0.65 wt.% NaCl, and 7.23 min, while the best-optimized conditions for AlEW were at 10.32 V, 0.6 wt.% NaCl, and 7.49 min. The performance of the optimum EW (AcEW and AlEW) compared with commercial cleaning detergents for the fo... [more]

This article is focused on the prediction of cutting material durability by Taylor’s model. To create predictive models of the durability of cutting materials in the turning process, tools made of high-speed steel, sintered carbide without coating and with Titanium nitride (TiN) coating, cutting ceramics without coating and with TiN coating were applied. The experimental part was performed on reference material C45 using conventional lathe—type of machine SU50A and computer numerical control machine—CNC lathe Leadwell T-5 in accordance with International Organization for Standardization—ISO 3685. Implementation of the least-squares method and processing of regression analysis made predictions of cutting tool behaviour in the turning process. Using the method of regression analysis, a correlation index of 93.5% was obtained, indicating the functional dependence of the predicted relationship.

We propose a new mathematical model describing a biotechnological process of simultaneous production of hydrogen and methane by anaerobic digestion. The process is carried out in two connected continuously stirred bioreactors. The proposed model is developed by adapting and reducing the well known Anaerobic Digester Model No 1 (ADM1). Mathematical analysis of the model is carried out, involving existence and uniqueness of positive and uniformly bounded solutions, computation of equilibrium points, investigation of their local stability with respect to practically important input parameters. Existence of maxima of the input−output static characteristics with respect to hydrogen and methane is established. Numerical simulations using a specially elaborated web-based software environment are presented to demonstrate the dynamic behavior of the model solutions.

Diagnosis of bearing faults is crucial in various industries. Time series classification (TSC) assigns each time series to one of a set of pre-defined classes, such as normal and fault, and has been regarded as an appropriate approach for bearing fault diagnosis. Considering late and inaccurate fault diagnosis may have a significant impact on maintenance costs, it is important to classify bearing signals as early and accurately as possible. TSC, however, has a major limitation, which is that a time series cannot be classified until the entire series is collected, implying that a fault cannot be diagnosed using TSC in advance. Therefore, it is important to classify a partially collected time series for early time series classification (ESTC), which is a TSC that considers both accuracy and earliness. Feature-based TSCs can handle this, but the problem is to determine whether a partially collected time series is enough for a decision that is still unsolved. Motivated by this, we propose... [more]

Nanoparticle-based therapeutics have been used in pulmonary formulations to enhance delivery of poorly water-soluble drugs, protect drugs against degradation and achieve modified release and drug targeting. This review focuses on the use of spray drying as a solidification technique to produce microparticles containing nanoparticles (i.e., nanoparticle (NP) agglomerates) with suitable properties as dry powders for inhalation. The review covers the general aspects of pulmonary drug delivery with emphasis on nanoparticle-based dry powders for inhalation and the principles of spray drying as a method for the conversion of nanosuspensions to microparticles. The production and therapeutic applications of the following types of NP agglomerates are presented: nanoporous microparticles, nanocrystalline agglomerates, lipid-based and polymeric formulations. The use of alternative spray-drying techniques, namely nano spray drying, and supercritical CO2-assisted spray drying is also discussed as a... [more]

This study aims to evaluate the sugar yield from enzymatic hydrolysis and the interactive effect pretreatment parameters of microwave-assisted pretreatment on glucose and xylose. Three types of microwave-assisted pretreatments of sago palm bark (SPB) were conducted for enzymatic hydrolysis, namely: microwave-sulphuric acid pretreatment (MSA), microwave-sodium hydroxide pretreatment (MSH), and microwave-sodium bicarbonate (MSB). The experimental design was done using a response surface methodology (RSM) and Box−Behenken Design (BBD). The pretreatment parameters ranged from 5−15% solid loading (SL), 5−15 min of exposure time (ET), and 80−800 W of microwave power (MP). The results indicated that the maximum total reducing sugar was 386 mg/g, obtained by MSA pretreatment. The results also illustrated that the higher glucose yield, 44.3 mg/g, was found using MSH pretreatment, while the higher xylose yield, 43.1 mg/g, resulted from MSA pretreatment. The pretreatment parameters MP, ET, and SL... [more]

Fluctuation in fossil fuel prices and the increasing awareness of environmental degradation have prompted the search for alternatives from renewable energy sources. Biodiesel is the most efficient alternative to fossil fuel substitution because it can be properly modified for current diesel engines. It is a vegetable oil-based fuel with similar properties to petroleum diesel. Generally, biodiesel is a non-toxic, biodegradable, and highly efficient alternative for fossil fuel substitution. In Malaysia, oil palm is considered as the most valuable commodity crop and gives a high economic return to the country. However, the ethical challenge of food or fuel makes palm oil not an ideal feedstock for biodiesel production. Therefore, attention is shifted to non-edible feedstock like Jatropha curcas Linnaeus (Jatropha curcas L.). It is an inedible oil-bearing crop that can be processed into biodiesel. It has a high-seed yield that could be continually produced for up to 50 years. Furthermore,... [more]

Since setup operations have significant impacts on production environments, the capacitated lot-sizing problem considering arbitrary length of setup times helps to develop flexible and efficient production plans. This study discusses a capacitated lot-sizing problem with sequence-dependent setup, setup carryover and setup crossover. A new mixed integer programming formulation is proposed. The formulation is based on three building blocks: the facility location extended formulation; the setup variables with indices for the starting and the completion time periods; and exponential number of generalized subtour elimination constraints (GSECs). A separation routine is adopted to generate the violated GSECs. Computational experiments show that the proposed formulation outperforms models from the literature.

A convolutional neural network (CNN) has been used to successfully realize end-to-end bearing fault diagnosis due to its powerful feature extraction ability. However, the CNN is prone to focus on local information, ignoring the relationship between the whole and the part of the signal due to its unique structure. In addition, it extracts some fault features with poor robustness under noisy environment. A novel diagnosis model based on feature fusion and feature selection, GL-mRMR-SVM, is proposed to address this problem in this paper. First, the model combines the global features in the time-domain and frequency-domain of the raw data with the local features extracted by CNN to make full use of the signal information and overcome the weakness of traditional CNNs neglecting the overall signal. Then, the max-relevance min-redundancy (mRMR) algorithm is used to automatically extract the discriminative features from the fused features without any prior knowledge. Finally, the extracted dis... [more]

A new dust suppression hopper with a spiral guide plate embedded in the conventional hopper is proposed for the dust suppression of hopper transfer processes in this article. The Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) coupling numerical method is used to investigate the particle motion and flow field distribution of the hopper transfer process. The experiment is undertaken to determine dust suppression performance. The results show that the maximum particle velocity for the spiral hopper is dropped by 1.6 m/s compared to the conventional hopper, which means the collision of the particles and the spiral hopper is weakened. The axial airflow velocity of the spiral is reduced. In addition, the maximum dust concentration of the spiral hopper inlet is reduced by 56.9% due to the impact velocity of particles is small, and the secondary fugitive dust is controlled inside a semi-closed space formed by the spiral guide plate. It is thus concluded that the spiral hopper p... [more]

A mathematical model composed of two non-linear differential equations that describe the population dynamics of CD4 T-cells in the human immune system, as well as viral HIV viral load, is proposed. The invariance region is determined, classical equilibrium stability analysis is performed by using the basic reproduction number, and numerical simulations are carried out to illustrate stability results. Thereafter, the model is modified with a delay term, describing the time required for CD4 T-cell immunological activation. This generates a two-dimensional integro-differential system, which is transformed into a system with three ordinary differential equations. For the new model, equilibriums are determined, their local stability is examined, and results are studied by way of numerical simulation.

Chromatography equipment includes hold-up volumes that are external to the packed bed and usually not considered in the development of chromatography models. These volumes can substantially contribute to band-broadening in the system and deteriorate the predicted performance. We selected a bubble trap of a pilot scale chromatography system as an example for a hold-up volume with a non-standard mixing behavior. In a worst-case scenario, the bubble trap is not properly flushed before elution, thus causing the significant band-broadening of the elution peak. We showed that the mixing of buffers with different densities in the bubble trap device can be accurately modeled using a simple compartment model. The model was calibrated at a wide range of flow rates and salt concentrations. The simulations were performed using the open-source software CADET, and all scripts and data are published with this manuscript. The results illustrate the importance of including external holdup volumes in ch... [more]

A CFD (computational fluid dynamics) analysis was carried out for the Bingham viscoplastic fluid flow simulations around cylinders of circular and square shapes. The governing equations in space were discretized with the finite element approach via a weak formulation and utilizing Ladyzhenskaya−Babuška−Brezzi-stable pair Q 2 / P 1 disc for approximation of the velocity and pressure profiles. The discrete non-linear system was linearized through Newton’s method, and a direct linear solver was iterated as an inner core solver. The study predicts the functional dependence and impact of Bingham number, B n , on the drag coefficient and lift coefficient. The effect of the shape of an obstacle is also provided by providing comparative data for the hydrodynamic forces with the published results.

A nanocrystalline zeolite of Na-X type (CFAZ) was synthesized by ultrasonic-assisted double stage fusion-hydrothermal alkaline conversion of lignite coal fly ash. Modified CFAZ with magnetic nanoparticles (MNP-CFAZ) was obtained by adding presynthesized magnetic nanoparticles between the synthesis stages. CFAZs loaded by particles of copper (Cu-CFAZ) and cobalt (Co-CFAZ) oxides were prepared by postsynthesis modification of the parent CFAZ, applying a wet impregnation technique. The parent and modified CFAZs were examined for their phase composition by X-ray diffraction, morphology by scanning electron microscopy, and surface characteristics by N2 physisorption. Comparative studies have been carried out on the adsorption capacity of the starting CFAZ and its derivatives with respect to Cd2+- and Pb2+-ions from aqueous solutions. Adsorption isotherms of Cd2+-ions on the studied samples were plotted and described by the adsorption equations of Langmuir, Freundlich, Langmuir−Freundlich, a... [more]

Recently, the global population has increased sharply, unfortunately, the availability of fossil fuel resources has significantly decreased. This phenomenon has become an attractive issue for many researchers in the world so that various studies in the context of finding renewable energy are developing continuously. Relating to this challenge, this research has been part of scientific work in the context of preparing an energy briquette employing palm oil stems and glycerol crude of biodiesel byproducts as inexpensive and green materials easily found in the Riau province, Indonesia. Technically, the palm oil stems are used for the production of charcoal particles and the glycerol crude as an adhesive compound in the production of energy briquettes. The heating value of palm oil stem is 17,180 kJ/kg, which can be increased to an even higher value through a carbonization process followed by a densification process so that it can be used as a potential matrix to produce energy briquettes.... [more]

Waste recycling is an essential part of waste management. The concrete industry allows the use of large quantities of waste as a substitute for a conventional raw material without sacrificing the technical properties of the product. From a circular economy point of view, this is an excellent opportunity for waste recycling. Nevertheless, in some cases, the recycling process can be undesirable because it does not involve a net saving in resource consumption or other environmental impacts when compared to the conventional production process. In this study, the environmental performance of conventional absorption porous barriers, composed of 86 wt % of natural aggregates and 14 wt % cement, was compared with barriers composed of 80 wt % seashell waste and 20 wt % cement through an attributional cradle-to-grave life cycle assessment. The results show that, for the 11 environmental impact categories considered, the substitution of the natural aggregates with seashell waste involves higher e... [more]

Optimization of flow fields in redox flow batteries can increase performance and efficiency, while reducing cost. Therefore, there is a need to establish a fundamental understanding on the connection between flow fields, electrolyte flow management and electrode properties. In this work, the flow distribution and pressure drop characteristics of interdigitated flow fields with constant and tapered cross-sections are examined numerically and experimentally. Two simplified 2D along-the-channel models are used: (1) a CFD model, which includes the channels and the porous electrode, with Darcy’s viscous resistance as a momentum sink term in the latter; and (2) a semi-analytical model, which uses Darcy’s law to describe the 2D flow in the electrode and lubrication theory to describe the 1D Poiseuille flow in the channels, with the 2D and 1D sub-models coupled at the channel/electrode interfaces. The predictions of the models are compared between them and with experimental data. The results s... [more]

This work proposes a Generic Model Control (GMC) strategy to regulate biomass growth in fed-batch cultures of Escherichia coli BL21(DE3). The control law is established using a previously validated mechanistic model based on the overflow metabolism paradigm. A model reduction is carried out to prevent the controller from relying on kinetics, which may be uncertain. In order to limit the controller to the use of a single measurement, i.e., biomass concentration which is readily available, a Kalman filter is designed to reconstruct the nonmeasurable information from the outlet gas and the remaining stoichiometry. Several numerical simulations are presented to assess the controller robustness with respect to model uncertainty. Experimental validation of the proposed GMC strategy is achieved with a lab-scale bioreactor.

Methane is activated at ambient conditions in a dielectric barrier discharge (DBD) plasma reactor packed with Pd/γ-alumina catalyst containing different loadings of Pd (0.5, 1, 5 wt%). Results indicate that the presence of Pd on γ-alumina substantially abates the formation of deposits, leads to a notable increase in the production of alkanes and olefins and additionally improves the energy efficiency compared to those obtained for the non-packed reactor and the bare γ-alumina packed reactor. A low amount of Pd (0.5 and 1 wt%) favors achieving a higher production of olefins (mainly C2H4 and C3H6) and a higher yield of H2. Increasing Pd loading to 5 wt% promotes the interaction of H2 and olefins, which consequently intensifies the successive hydrogenation of unsaturated compounds, thus incurring a higher production of alkanes (mainly C2H6 and C3H8). The substantial abatement of the deposits is ascribed to the role of Palladium in moderating the strength of the electric and shifting the r... [more]

The heat transfer was experimentally and numerically studied in this article. Characteristics of circular fins over a bent tube at different tube orientations and air velocities were investigated, and then compared with analytical results from the literature. For the experimental investigation, a simple setup was compiled inside of a wind tunnel, where the velocity and the inlet temperature of the air; the volume flow rate; and the inlet and outlet temperatures of the water were measured. Three different orientations were investigated with the set-up: the bent tube in line with the air flow with the same and opposite water inlet positions, and the bent tube perpendicular to the air flow. According to the results, the position has a significant effect on the heat transfer coefficient. A numerical study was also performed in accordance with the measurements in ANSYS-CFX computational fluid dynamics (CFD) software. The results of the CFD showed an acceptable correlation with the results o... [more]

During recent years, there has been great interest in exploring the potential for high-rate natural gas (NG) injection in North American blast furnaces (BFs) due to the fuel’s relatively low cost, operational advantages, and reduced carbon footprint. However, it is well documented that increasing NG injection rates results in declining raceway flame temperatures (a quenching effect on the furnace, so to speak), with the end result of a functional limit on the maximum injection rate that can be used while maintaining stable operation. Computational fluid dynamics (CFD) models of the BF raceway and shaft regions developed by Purdue University Northwest’s (PNW) Center for Innovation through Visualization and Simulation (CIVS) have been applied to simulate multi-phase reacting flow in industry blast furnaces with the aim of exploring the use of pre-heated NG as a method of widening the BF operating window. Simulations predicted that pre-heated NG injection could increase the flow of sensib... [more]

Moringa extract was microencapsulated for the first time by spray-drying technique using tragacanth gum (MorTG) to improve its stability under gastrointestinal and storage conditions, assessing total polyphenolic content (TPC) and antioxidant activity. Additionally, cytotoxicity of the microencapsulated components was evaluated after contact with Caco-2 cells. Results showed that TPC was released as follows—oral (9.7%) < gastric (35.2%) < intestinal (57.6%). In addition, the antioxidant activity in in vitro digestion reached up to 16.76 ±0.15 mg GAE g−1, which was 300% higher than the initial value. Furthermore, microencapsulated moringa extract presented a half-life up to 45 days of storage, where the noticeably change was observed at 35 °C and 52.9% relative humidity. Finally, direct treatment with 0.125 mg mL−1 MorTG on Caco-2 cells showed a slight antiproliferative effect, with a cell viability of approx. 87%. Caco-2 cells’ viability demonstrated non-cytotoxicity, supporting... [more]