High-pressure direct-injection (HPDI) natural gas marine engines are widely used because of their higher thermal efficiency and lower emissions. The effects of different injection rate shapes on the combustion and emission characteristics were studied to explore the appropriate gas injection rate shapes for a low-speed HPDI natural gas marine engine. A single-cylinder model was established and the CFD model was validated against experimental data from the literature; then, the combustion and emission characteristics of five different injection rate shapes were analyzed. The results showed that the peak values of in-cylinder pressure and heat release rate profiles of the triangle shape were highest due to the highest maximum injection rate, which occurred in a phase close to the top dead center. The shorter combustion duration of the triangle shape led to higher indicated mean effective pressure (IMEP) and NOx emissions compared with other shapes. The higher initial injection rates of t... [more]

In building design, several approaches have been proposed for coupling computational fluid dynamics (CFD) and energy simulation (ES) to perform analyses of thermal environments. The unsteady analysis of thermal environments within buildings containing offices and colonnade spaces is difficult to perform using an ES that represents the space with a single mass point, owing to excessive predictive heat loss; therefore, CFD has typically been used instead. Although it is possible to divide the space into zones using ES, it leads to excessive predicted heat loss and the prediction of heat movement due to the influence of strong air currents, such as those associated with air conditioners. This behavior is observed because these zones are not detailed mesh divisions. To solve these problems, we proposed a method for calculating the ratio of heat contribution to zones that were pre-divided using CFD followed by the distribution of the total thermal load calculated by ES. In this study, we pr... [more]

This paper presents a numerical investigation of ignition and combustion stabilization of a novel design of a solid-fuel ramjet (SFRJ) motor with and without swirl flow. The proposed design includes two solid fuels, retaining the simple design of the classic SFRJ. Numerical simulations of unsteady, turbulent, reactive, and swirling flow coupled with solid-fuel pyrolysis have been performed using an in-house CFD solver. Experiments on SFRJ were conducted via a connected-pipe test facility to validate the developed code. Furthermore, the code was validated for chemical reactions, heat diffusion, and swirl flow by using benchmark test cases of shock-induced, semi-infinite plate, and dump combustor with swirl flow, respectively. Then, the proposed and classic designs were simulated for the same inflow conditions and configurations, and the results were analyzed and discussed. It is found that the mixing degree, reactant residence time, mass flux, ignition delay time, and regression rate im... [more]

Aerodynamics of the Darrieus wind turbine is an extremely complex issue requiring the use of very advanced numerical methods. Additional structural components of this device, such as, for example, a rotating shaft disturb the flow through the rotor significantly impairing its aerodynamic characteristics. The main purpose of the presented research is to validate the commonly-used unsteady Reynolds averaged Navier−Stokes (URANS) approach with the shear stress transport (SST) k-ω turbulence model based on the particle image velocimetry (PIV) studies of a two-bladed rotor operating at the moderate tip speed ratio of 4.5. In the present numerical studies, a two-dimensional turbine rotor with a diameter of 1 m was considered. The following parameters were evaluated: instantaneous velocity fields; velocity profiles in the rotor shadow and aerodynamic blade loads. The obtained numerical results are comparable with the reference experimental results taken from the literature. The second purpose... [more]

This study aims to investigate the influence of the current direction on the energy production of a tidal turbines array. It is based on a three-dimensional (3D) numerical simulation of the flow where the turbines are represented with actuator disks. The case study consists of modelling the energy extraction of a small array of turbines (staggered and aligned layouts) placed in the Raz Blanchard (Alderney Race, France). The simulations are performed with hydrodynamic data (current magnitude and direction) representative of a mean tide, with several resistance forces and ambient turbulence intensities. The influence of the current direction on the energy production is highlighted by comparing the simulations forced with the real current direction with those in which the angle of incidence between the incoming flow and the turbine’s axis is “switched off” (bi-directional flow). When the flow is aligned with the turbines’ axis (misalignment “switched off”), the staggered layout produces m... [more]

The limitation of nitrogen oxides emissions is nowadays a challenge in several engineering fields. Recent European regulations have reduced the maximum NOx emissions and therefore forced the glass production sector to develop emission reduction strategies. Two different systems have been developed within the framework of the European LIFE project and are currently applied to glass regenerative furnaces: the Waste Gas Recirculation (WGR) and the Hybrid Air Staging (HyAS). The above systems are primary NOx reduction strategies because they both operate to control the combustion evolution. Both WGR and HyAS systems have been conceived with the extensive use of Computational Fluid Dynamics (CFD) models: design strategies for both systems have been developed based on the use of CFD and are currently under use by glass furnace designers. In the present work, the CFD procedures routinely used for the design of the above systems are described. The systems effectiveness, due to the harsh condit... [more]

The ability to model fluid flow and heat transfer in process equipment (e.g., shell-and-tube heat exchangers) is often critical. What is more, many different geometric variants may need to be evaluated during the design process. Although this can be done using detailed computational fluid dynamics (CFD) models, the time needed to evaluate a single variant can easily reach tens of hours on powerful computing hardware. Simplified CFD models providing solutions in much shorter time frames may, therefore, be employed instead. Still, even these models can prove to be too slow or not robust enough when used in optimization algorithms. Effort is thus devoted to further improving their performance by applying the symmetric successive overrelaxation (SSOR) preconditioning technique in which, in contrast to, e.g., incomplete lower−upper factorization (ILU), the respective preconditioning matrix can always be constructed. Because the efficacy of SSOR is influenced by the selection of forward and... [more]

Wind turbines installed in cold-climate regions are prone to the risks of ice accumulation which affects their aeroelastic behavior. The studies carried out on this topic so far considered icing in a few sections of the blade, mostly located in the outer part of the blade, and their influence on the loads and power production of the turbine are only analyzed. The knowledge about the influence of icing in different locations of the blade and asymmetrical icing of the blades on loads, power, and vibration behavior of the turbine is still not matured. To improve this knowledge, multiple simulation cases are needed to run with different ice accumulations on the blade considering structural and aerodynamic property changes due to ice. Such simulations can be easily run by automating the ice shape creation on aerofoil sections and two-dimensional (2-D) Computational Fluid Dynamics (CFD) analysis of those sections. The current work proposes such methodology and it is illustrated on the Nation... [more]

Using computational fluid dynamics (CFD), this study explores the effect of a different number of awning windows and their installation locations on the airflow patterns and air contaminant distributions in restrooms in K-12 (for kindergarten to 12th grade) public schools in Taiwan. A representative restroom configuration with dimensions of 10.65 m × 9.2 m × 3.2 m (height) was selected as the investigated object. Based on the façade design feasibility, seven possible awning window configurations were considered. The results indicate that an adequate number of windows and appropriate installation locations are required to ensure the natural ventilation effectiveness of awning windows. The recommended installation configuration is provided.

Sports halls must meet strict requirements for energy and indoor air quality (IAQ); therefore, there is a great challenge in the design of the heating, ventilation, and air conditioning (HVAC) systems of such buildings. IAQ in sports halls may be affected by thermal stratification, pollutants from different sources, the maintenance of building, and the HVAC system of the building, as well as by the activities performed inside the building. The aim of this study is to investigate thermal stratification conditions in accordance with the performance of the HVAC systems in the basketball training hall of Žalgirio Arena, Kaunas in Lithuania. Field measurements including temperature, relative humidity, and CO2 concentration were implemented between January and February in 2017. The temperature and relative humidity were measured at different heights (0.1, 1.7, 2.5, 3.9, 5.4, and 6.9 m) and at five different locations in the arena. Experimental results show that mixing the ventilation applica... [more]

Nowadays, an accurate and precise description of the combustion phase is essential in spark-ignition (SI) engines to drastically reduce pollutant and greenhouse gas (GHG) emissions and increase thermal efficiency. To this end, computational fluid dynamics (CFD) can be used to study the different phenomena involved, such as the ignition of the charge, combustion development, and pollutant formation. In this work, a validation of a CFD methodology based on the flame area model (FAM) was carried out to model the combustion process in light-duty SI engines fueled with natural gas. A simplified spherical kernel approach was used to model the ignition phase, whereas turbulent flame propagation was described through two variables. A zero-dimensional evolution of the flame kernel radius was used in combination with the Herweg and Maly formulation to take the laminar-to-turbulent flame transition into account. To estimate the chemical composition of burnt gas, two different approaches were cons... [more]

Thermal energy storages represent important devices for the decarbonisation of heat; hence, enabling a circular economy. Hereby, important tasks are the optimisation of thermal losses and providing a tuneable storage capacity, as well as tuneable storage dynamics for thermal energy storage modules which are composed of either sensible or phase change-based heat storage materials. The thermal storage capacity and the storage dynamics behaviour are crucial for fulfilling certain application requirements. In this work, a novel macro-encapsulated and spherical heat storage core-shell structure is presented and embedded in a supercritical ammonia working fluid flow field. The core of the macro-capsule is built by an organic low molecular weight substance showing a solid−liquid phase transition in a respective temperature zone, where the shell structure is made of polyvinylidene fluoride. Due to the direct coupling of computational fluid dynamics and the simulation of the phase transition of... [more]

The paper provides an outlook on future directions of research and the possible applications for pulverized coal-fired boilers. One potential direction for future research is to focus on the ways to improve the efficiency of pulverized coal-fired boilers. This could involve developing new combustion technologies that are able to more thoroughly burn the coal and produce less waste or finding ways to capture and use the excess heat that is generated during the combustion process. The pulverized coal combustion process in power boilers is still being improved by the preliminary cleaning of coal and the use of various catalytic additives. Another area of research that could be valuable is the development of advanced control systems and monitoring technologies for pulverized coal-fired boilers. These systems could be used to optimize the performance of the boiler and ensure that it is operating at maximum efficiency while also providing real-time data on the condition of the boiler and any... [more]

The main heat transfer mechanism in the end-winding region of electrical machines is convection. In order to increase the air motion, the rotor is equipped with a series of blades. Their geometry is reflected in the fanning factor, i.e., the ratio between the rotor peripheral speed and air velocity. An accurate calculation procedure for the fanning factor has not yet been given. Knowing its value is crucial for the determination of air velocity and heat transfer coefficient (HTC), as the latter describes the end-winding heat removal capability. In this study, the convective heat transfer phenomena between the end winding and air inside the end-winding region were analyzed, with the heat generated only in the end winding, mimicked with a custom designed coil, and air moved by the blades. The analysis was performed by experimental testing and computational fluid dynamics (CFD) modeling. Measurements data were used to build a reliable CFD model. Further on, CFD results were used to derive... [more]

Computational Fluid Dynamics (CFD) frameworks of supercritical cryogenic fluids need to employ Real Fluid models such as cubic Equations of State (EoS) to account for thermal and inertial driven mechanisms of fluid evolution and disintegration. Accurate estimation of the non-linear variation in density, thermodynamic and transport properties is required to computationally replicate the relevant thermo and fluid dynamics involved. This article reviews the availability, performance and the implementation of common Real Fluid EoS and data-based models in CFD studies of supercritical cryogenic fluids. A systematic analysis of supercritical cryogenic fluid (N2, O2 and CH4) thermophysical property predictions by cubic (PR and SRK) and non-cubic (SBWR) Real Fluid EoS, along with Chung’s model, reveal that: (a) SRK EoS is much more accurate than PR at low temperatures of liquid phase, whereas PR is more accurate at the pseudoboiling region and (b) SBWR EoS is more accurate than PR and SRK desp... [more]

In this paper, the applicability of advanced heat transfer enhancement technology to a paddle dryer was discussed. A computational fluid dynamics (CFD) method was used to simulate condensation heat transfer on the inner surface of a dryer paddle. The effect of surface wettability and rotation on condensation heat transfer and droplet behavior was studied. The results showed that the present CFD model could properly simulate the condensation process on a vertical surface. With a decrease in the contact angle, the filmwise condensation turned into a dropwise condensation, which resulted in a significant increase in heat transfer coefficient and provided an approximately 5% increase in evaporation rate for the paddle dryer by changing the wettability of the inner surface of the paddle. Additionally, with a change in rotational angular velocity, heat transfer performance was almost unchanged under the filmwise condensation condition. However, rotational motion might cause a decrease in wal... [more]

Shell and tube heat exchangers are used to transfer thermal energy from one medium to another for regulating fluid temperatures in the processing and pasteurizing industries. Enhancement of a heat transfer rate is desired to maximize the energy efficiency of the shell and tube heat exchangers. In this research work, we performed computational fluid dynamics (CFD) simulations and experimental analysis on the shell and tube heat exchangers using round and hexagonal tubes for a range of flow velocities using both parallel flow and counter flow arrangements. In the present work, the rate of heat transfer, temperature drop, and heat transfer coefficient are computed using three turbulence models: the Spalart−Allmaras, the k-epsilon (RNG), and the k-omega shear stress transport (SST). We further utilized the logarithmic mean temperature difference (LMTD) method to compute the heat transfer and mass flow rates for both parallel and counter flow arrangements. Our results show that the rate of... [more]

The present study focused on the analysis of a new geometrical modification of the conventional zig-zag channel for Printed Circuit Heat Exchangers. The research was carried out using OpenFOAM and Salome software, which were used for the CFD analysis and the construction of the computational domain. For the development of the study, three types of channel geometries were defined: a modified zig-zag channel, a conventional zig-zag channel, and a straight channel. The results show that the modified zig-zag channel achieves better thermal hydraulic performance compared to that of the conventional zig-zag channel, evidenced by a 7.6% increase in the thermal performance factor. The modified zig-zag channel proposed in the research caused a 1.5% reduction of the power consumption of supercritical Brayton cycle compressors. Additionally, the modified zig-zag channel achieves a maximum efficiency of 49.1%, which is 1.5% higher compared to that of the conventional zig-zag channel. The above res... [more]

In the study of solar greenhouses, microclimate, soil, and back walls have an important influence on the greenhouse thermal environment because of their good heat storage and release characteristics. The transpiration of crops makes indoor humidity increase sharply, which is the main factor affecting indoor humidity distribution. Therefore, it is of great significance to grasp the microclimate change law of solar greenhouses and study the coupling effect of thermal and humidity environment. In this paper, based on computational fluid dynamics (CFD), a three-dimensional model of the thermal and humidity environment of a solar greenhouse is established, and the indoor temperature and humidity distribution under the influence of soil, crops, and back walls are considered. The CFD model initialization uses binary fitting functions to fit the temperature distribution of soil, back wall, and air. The distribution law of the temperature field and relative humidity field of the solar greenhous... [more]

A scaled-down test section representative of an Outboard Segment manifold of the Water-Cooled Lithium Lead Breeding Blanket for the European DEMO has been designed for installation and test in a high- mass flow branch of the W-HYDRA facility, under construction at the premises of ENEA Brasimone Research Center. The test section should confirm the flow repartition recently computed in the different breeding units on the full-scale manifold, validating at the same time the computational tools used for the design and analysis. The detailed objectives and requirements of the test section, as well as the scaling rationale and procedure adopted for its design, are presented in the paper. The final design of the test section is discussed. The preliminary analyses of the developed design are also presented and show that it is compliant with the initial objectives.

The influence of the improvement of the finned tube radiator unit structure on the fluid flow and heat transfer effect of the locomotive was studied. A saw-toothed fin structure with aluminum instead of copper was proposed to keep the position and size of the flat copper hot water pipe unchanged. CFD simulation analysis was carried out by ICEPAK17.0, under the conditions of an ambient temperature of 24.6 °C, atmospheric pressure of 85,040 Pa and air density ρ = 0.94 kg/m3, to compare the changes of velocity field, temperature field, turbulence field and field synergy angle. The sawtooth structure of the new heat sink increases the turbulence effect of the fluid, reduces the thickness of the outer boundary layer of the water pipe, and strengthens the heat transfer effect of the radiator. Finally, the baffle height, wing window width and sawtooth angle of the sawtooth structure were selected, and the heat transfer coefficient and pressure under three conditions of low, medium and high we... [more]

Mixing under high pressure conditions plays a central role in several engineering applications, such as direct-injection engines and liquid rocket engines. Numerical flow simulations have become a complementary tool to study the mixing process under these conditions but require complex thermodynamic modeling as well as validation with accurate experimental data. For this reason, we use experiments of supercritical single-phase jet mixing from the literature, where the mixing is quantified by the mixture speed of sound, as a reference for our work. We here focus on the thermodynamic modeling of multi-component flows under high pressure conditions and the analytical calculation of the mixture speed of sound. Our thermodynamic model is based on cubic equations of state extended for multi-components. Using an extension of OpenFOAM, we perform large-eddy simulations of hexane and pentane injections and compare our results with the experimentally measured mixture speed of sound at specific p... [more]

From conventional turbines to cutting-edge bladeless turbines, energy harvesting from wind has been well explored by researchers for more than a century. The vortex bladeless wind turbine (VBT) is considered an advanced design that alternatively harvests energy from oscillation. This research investigates enhancing the output electrical power of VBT through simulation of the fluid−solid interactions (FSI), leading to a comprehensive dataset for predicting procedure and optimal design. Hence, the long short-term memory (LSTM) method, due to its time-series prediction accuracy, is proposed to model the power of VBT from the collected data. To find the relationship between the parameters and the variables used in this research, a correlation matrix is further presented. According to the value of 0.3 for the root mean square error (RMSE), a comparative analysis between the simulation results and their predictions indicates that the LSTM method is suitable for modeling. Furthermore, the LST... [more]

In this study, the influence of architectural design parameters (the exterior window area, the wall height at a corridor-side, and the door gap of a toilet unit) on the airflow patterns and malodorous volatile substance (acetic acid) distributions within toilet units were investigated via computational fluid dynamics (CFD), with the restrooms in K−12 public schools (kindergarten through grade 12) of Taiwan as research objects. The results show that when there is a 2 m/s north wind in winter, all the cases exceed the required 12 air changes per hour (ACH), and most are above 43.75 ACH. When there is a 0.5 m/s south wind in summer, nearly half of the cases fail to reach 12 ACH. Maintaining an adequate natural ventilation rate and an acceptable level of odor pollution through passive design and architectural design is difficult. Thinking about how to improve the ventilation efficiency of toilet units with the aid of simple, appropriate, and energy-saving mechanical ventilation approaches... [more]

Radiant cooling systems (RCS) are gaining acceptance as a heating, ventilation, and air conditioning (HVAC) solution for achieving adequate thermal comfort and maintaining acceptable indoor air quality inside buildings. RCS are well known for their energy-saving potential; however, serious condensation problem hinders the growth of this technology. In order to prevent the risk of condensation, the supply water temperature is kept higher than the dew point temperature of the air inside the room. The full potential of the cooling power of a radiant cooling panel is limited. Therefore, this article is on maximizing the cooling capacity of a radiant cooling panel, in terms of flow configuration. Radiant cooling panels (RCP) with different chilled water pipe configurations are designed and compared, side by side with the conventional serpentine flow configuration. The cooling performance of the radiant cooling panels is evaluated by using computational fluid dynamics (CFD) with Ansys Fluent... [more]