In this study, we present a new algorithm for finding the optimal friction stir welding parameters to maximize the tensile strength of a butt joint made of the semisolid material (SSM) ADC 12 aluminum. The welding parameters were rotational speed, welding speed, tool tilt, tool pin profile, and rotational direction. The method presented is a variable neighborhood strategy adaptive search (VaNSAS) approach. The process of finding the optimal friction stir welding parameters comprises five steps: (1) identifying the type and range of friction stir parameters using a literature survey; (2) performing experiments according to (1); (3) constructing a regression model using the response surface method optimizer (RSM optimizer); (4) using VaNSAS to find the optimal parameters for the model obtained from (3); and (5) confirming the results from (4) using the parameter levels obtained from (4) to perform real experiments. The computational results revealed that the tensile strength generated fr... [more]

This paper is concerned with the real-time optimization (RTO) of chemical plants, i.e., the optimization of the steady-state operating points during operation, based on inaccurate models. Specifically, modifier adaptation is employed to cope with the plant-model mismatch, which corrects the plant model and the constraint functions by bias and gradient correction terms that are computed from measured variables at the steady-states of the plant. This implies that the sampling time of the iterative RTO scheme is lower-bounded by the time to reach a new steady-state after the previously computed inputs were applied. If analytical process measurements (PAT technology) are used to obtain the steady-state responses, time delays occur due to the measurement delay of the PAT device and due to the transportation delay if the samples are transported to the instrument via pipes. This situation is quite common because the PAT devices can often only be installed at a certain distance from the measur... [more]

The advancements in human lifestyle result in growth in daily demands of products, and accordingly, an increased rate of manufacturing. However, the resources on the planet Earth are limited, thus depleting day-by-day. More goods also contribute to more end-of-life (EOL) dumping or even before EOL in some cases. Therefore, an interest in remanufacturing has appeared, and it offers a solution that can solve or perhaps mitigate the risks of consuming more resources and increasing waste. Remanufacturing is a procedure of bringing used products to “like-new” functional status with a matching warranty. However, due to its relative novelty in terms of research field and industry, remanufacturing is poorly understood. People often mix it with other terms such as recycling, reconditioning, or repair. Therefore, in this research, the focus is on the remanufacturing systems’ definition, relevance, main phases, case studies, and solution methods proposed by various researchers. The word ‘remanufa... [more]

Dynamic flux balance models (DFBM) are used in this study to infer metabolite concentrations that are difficult to measure online. The concentrations are estimated based on few available measurements. To account for uncertainty in initial conditions the DFBM is converted into a variable structure system based on a multiparametric linear programming (mpLP) where different regions of the state space are described by correspondingly different state space models. Using this variable structure system, a special set membership-based estimation approach is proposed to estimate unmeasured concentrations from few available measurements. For unobservable concentrations, upper and lower bounds are estimated. The proposed set membership estimation was applied to batch fermentation of E. coli based on DFBM.

As the carbon emissions of commercial buildings are attracting considerable attention, the integrated energy system (IES) has become a promising low-carbon method in response. In this paper, an optimization framework for low-carbon oriented integrated energy system management under electric vehicles (EV) demand response is proposed. After analyzing the charging behavior, EV charging demand is simulated. Then, the low-carbon integrated energy system model is proposed with the optimization framework considering carbon reduction. Subsequently the objective function containing carbon emission is obtained for the whole operation optimization. The results of the studied case show that the optimization framework proposed can reduce the carbon emission greatly as well as moderate economic cost, which declined because of the revenue from charging demand response. In general, the optimization of low-carbon oriented IES in commercial buildings is feasible.

Many ports worldwide continue to expand their capacity by developing a multiterminal system to catch up with the global containerized trade demand. However, this expansion strategy increases the demand for container exchange between terminals and their logistics facilities within a port, known as interterminal transport (ITT). ITT forms a complex transportation network in a large port, which must be managed efficiently given the economic and environmental implications. The use of trucks in ITT operations leads to the interterminal truck routing problem (ITTRP), which has been attracting increasing attention from researchers. One of the objectives of truck routing optimization in ITT is the minimization of empty-truck trips. Selection of the transport order (TO) based on the current truck location is critical in minimizing empty-truck trips. However, ITT entails not only transporting containers between terminals operated 24 h: in cases where containers need to be transported to a logist... [more]

Deep eutectic solvents (DESs) have properties that make them suitable candidates to be used as entrainers for extractive distillation. In the previous work, it was proven that DES(1:2) (tetrabutylammonium bromide: levulinic acid, 1:2, molar ratio) can break the cyclohexane-benzene azeotrope. In the present work, the HBA and HBD ratio and molar concentration of DES were optimized to obtain a better constitute and condition of DES to be utilized in cyclohexane and benzene extractive distillation. The physical properties and structure of the prepared DESs were characterized. Vapor−liquid equilibrium data of the ternary system (benzene + cyclohexane + DESs) were also measured at atmospheric pressure. All experimental equilibrium data were correlated with Wilson, nonrandom two-liquid (NRTL), and universal quasichemical (UNIQUAC) activity coefficient models, from which the coefficient of determination (R2) of the three pseudo-ternary systems fitting was calculated. From the obtained results,... [more]

The aim of this study was the development and optimization of chitosan and hydroxypropyl methylcellulose (HPMC) in situ gelling systems, loaded with bupivacaine hydrochloride for topical ocular administration. This study is based on the properties of two polymers: chitosan, which has mucoadhesive action and is a pH-sensitive polymer, but also the cellulose derivative hydroxypropyl methylcellulose, a thermosensitive polymer which has mucoadhesive properties and increases the viscosity of systems. The analysis and optimization of in situ gelling systems were performed based on an experimental design and response surface methodology. The following formulation parameters were considered: X1 = chitosan concentration (0.5%, 1%), X2 = HPMC E 5 LV concentration (2%, 5%) and X3 = Chitosan/HPMC E 5 LV ratio (1/1, 2/1). In addition, the parameters to be optimized were represented by the contact angle (CA (°)), viscosity and cumulative percentage of bupivacaine hydrochloride released in vitro. The... [more]

L-citrulline plays important roles in many physiological processes, and its application range is expanding rapidly. Corynebacterium glutamicum strains have the potential to be efficient L-citrulline producers. In this study, we performed optimization of L-citrulline biosynthesis operon in C. glutamicum ATCC13032 for L-citrulline production. Chromosomal integration of the integral argBEc gene from Escherichia coli (encoding natively insensitive N-acetylglutamate kinase), the deletion of the argR gene (encoding repressor ArgR), and the deletion of the argG gene (encoding argininosuccinate synthase) were achieved simultaneously by one-step genome modification and by obtaining the L-citrulline-producing strain. Then, plasmid-based overexpression of the optimized L-citrulline operon was carried out and the L-citrulline production was further improved. In fed-batch fermentation, the L-citrulline production and yield from glucose of the final strain reached 26.7 g/L and 0.18 g/g, respectively... [more]

Most spoilers are made from a sandwich structure with a honeycomb component as its core. However, the honeycomb core is sensitive to water ingress, causing damage to the control surface due to its weak moisture-resistance behavior. This study aimed to conduct the design and analysis of an improved composite structure for a coreless spoiler. A spoiler design of an aircraft, the A320, was used for the case study. The weaknesses of a coreless spoiler were identified through finite element analysis via Abaqus software. Multi-spar and multi-rib designs were studied and compared for topological optimization. The variables used for evaluation were the Tsai−Hill failure index and the critical buckling load. The design with the most potential was considered for parametric optimization to obtain the most satisfactory configuration. The results showed that the upper skin of the spoiler without a honeycomb core failed the Tsai−Hill criteria. Furthermore, the results show that the multi-spar config... [more]

(L.) Harms is commonly used for medicinal purposes in Vietnam. In traditional medicine, the plant is used to cure ischemia, reduce inflammation, and increase cerebral blood circulation. Triterpene saponins are the major chemical constituents found in the roots of P. fruticosa. This compound exhibited a broad spectrum of biological effects, including lowering blood sugar, suppressing tumor growth and inflammation. This study focused on optimizing the process of total saponins extraction from P. fruticosa roots using the ultrasonic-assisted extraction (UAE) method, ethanol solvent and response surface methodology, and Box−Behnken design model, then evaluating the cytotoxic effect against some cancer cell lines. The results showed that under the optimal conditions, including an extraction temperature of 60 °C and ultrasonic power of 185 W in 65 min, the maximum extraction yield and total saponin content were 14.51 ± 1.15% and 41.24 ± 1.68 mg/g, respectively. Moreover, the saponin extract... [more]

This study investigated the sealing performance of the multistage liquid-sealing impellers of a turbopump. To achieve this purpose, the influence of each structural parameter in the impeller on the pressurization coefficient φ2 and the leakage flow rate Q was analyzed based on response surface methodology, taking the maximum pressurization coefficient φ2 and the minimum leakage flow rate Q as the optimization objectives. We obtained satisfactory ranges for parameters φ2 and Q. A set of parameter combinations was selected as the optimization scheme using the Box−Behnken method for the optimal solution design. The numerical simulation results show that to keep φ2 and Q in the better range, the value ranges of groove width b, groove depth h and groove number z should be (12.8−14 mm), (4.5−5.6 mm) and (23.5−28), respectively. Compared with the original model, the optimized version has an average increase of about 2.5% in pressurization coefficient φ2 at each rotation speed, an average of a... [more]

The COVID-19 pandemic broke out and the global logistics industry suffered severe losses; therefore, the Fuzzy FMEA-AHP (Fuzzy Failure Mode and Effects Analysis-Analytic Hierarchy Process) method is proposed to analyze the failure reasons of the logistics system in the COVID-19 pandemic. In this article, we have made an optimization on the basis of the FMEA method: the fuzzy is integrated into the FMEA algorithm, referred to as F-RPWN (fuzzy risk priority-weighted number). Meanwhile, the AHP is used to determine the weights of risk indicators. In this article, we consider new logistics failures, such as the failure modes and failure reasons of the logistics system under the COVID-19 pandemic. There are 12 failures that have been determined, and relevant preventive and corrective measures have been recommended to cut off the path of failure propagation and reduce the impact of failures. In addition, the proposed method can help logistics firms, their supply chain partners, and customers... [more]

A nonlinear mathematical model for the optimal operation of a parallel pumping station group was established with the objective of minimizing the operation costs of the station group considering the target quantity of water extraction and flow unevenness between units of each station as constraints. The original model is decomposed into several sub-models with a single station multi-objective optimization operation with the target water lifting capacity of a single pump station as the coordinating variable. This constructed model was solved using a large-scale system decomposition dynamic programming aggregation method based on sub-system multi-objective genetic algorithm optimization. Taking the Jiangdu parallel pumping station group in the Chinese East Route of the South-to-North Water Diversion Project as a case study, the results show that under the condition of 80% water lifting load of parallel stations and 7.8 m daily average lift, the unit water lifting cost of the optimal oper... [more]

Spent coffee grounds (SCGs) generated in coffee processing for beverages and other products are a very significant organic residue that needs to be properly treated. Waste valorization via oil extraction has the potential to obtain compounds that can be used for producing biodiesel or other high-value products, such as polymers. This work focuses on the ultrasound-assisted extraction of SCG oil using n-hexane as a solvent. Three key process parameters are analyzed: temperature, extraction time, and liquid/solid (L/S) rate of solvent, using a central composite rotatable design (CCRD), an analysis that, to the author’s knowledge, is not yet available in the literature. The data were analyzed using the software StatSoft STATISTICA 13.1 (TIBCO Software Inc., Palo Alto, CA, USA). Results show that all parameters have a statistical influence on the process performance (p < 0.05), being the L/S ratio the most significant, followed by extraction time and temperature. An analysis of variance... [more]

Low-temperature atmospheric pressure (AP) plasma technologies have recently proven to offer a range of interesting opportunities for the preparation of a variety of nanocomposite (NC) coatings with different chemical compositions, structures, and morphologies. Since the late 2000s, numerous strategies have been implemented for the deposition of this intriguing class of coatings by using both direct and remote AP plasma sources. Interestingly, considerable progress has been made in the development of aerosol-assisted deposition processes in which the use of either precursor solutions or nanoparticle dispersions in aerosol form allows greatly widening the range of constituents that can be combined in the plasma-deposited NC films. This review summarizes the research published on this topic so far and, specifically, aims to present a concise survey of the developed plasma processes, with particular focus on their optimization as well as on the structural and functional properties of the N... [more]

exerts various medicinal effects and has been used as a traditional medicine for inflammation, asthma, gastritis, and liver disease. Recently, we reported the xanthine oxidase inhibitory activity of C. lanceolata extract and that lobetyolin, one of the key components, was a xanthine oxidase inhibitor. Lobetyolin showed anti-hyperuricemic activity in vitro and in vivo. In this study, we prepared various types of C. lanceolata extracts for the development of functional materials and natural drugs. We present the optimal analytical approach for the quality control and extraction optimization of C. lanceolata preparations. We established and validated a HPLC analysis for easy separation and quantification of the lobetyolin biomarker. Solvent extracts of C. lanceolata root were prepared and the profiles of the active marker and the optimal extraction methods were evaluated. The 100% ethanolic extract demonstrated the highest lobetyolin content. The validated HPLC method confirmed that lobet... [more]

Wheat straw and eucalyptus residues were pretreated in a biphasic system, constituted of butanol (n-butanol) or 2-methyltetrahydrofuran (2M-THF) and aqueous oxalic acid solutions. The pretreatments were carried out in a 300 mL Parr reactor (Autoclave Buchi Limbo-li®) with a solid load of 5 wt.%, the temperature in the range 140−180 °C, oxalic acid load from 0 to 10 wt.% and a duration of 30−90 min. The obtained slurry was then fractionated in three streams: the aqueous phase which contained solubilized hemicellulose, the organic phase which contained the solvated lignin, and the solid residue which contained cellulose. The solid was hydrolyzed using a commercial mix of enzymes to assess cellulose digestibility and glucose production. The pretreatment was optimized to maximize the purity of the cellulose and hemicellulose fractions and the glucose recovery as free sugar. The optimization was done by using an experimental design and response surface methodology. The mass flow details of... [more]

Design optimization on the Indonesia N219 seaplane catamaran is necessary to provide better service to rural islands of Indonesia. This research aims at decreasing drag using a design based on biomimicry by imitating the hydrodynamic characteristics of sailfish (Istiophorus platypterus) for pontoon floats. The design is then validated using a numerical fluid test using ANSYS Fluent to see the reduction in drag due to the change from a conventional or Wipeline® 13000 design to a biomimetics adaptation design. Next, further optimization was carried out based on the adaptation design based on trim tests, clearance tests, and deadrise angle dimensions suitable for biomimicry designs at Froude number speeds of 0.4 to 0.7. The design results with the adaptation of biomimicry show that a change in the design with this optimization affects a drag reduction that reaches 30% of the total drag generated by the conventional design.

This paper proposes a robust optimization algorithm customized for the optimal design of electric machines. The proposed algorithm, termed “robust explorative particle swarm optimization” (RePSO), is a hybrid algorithm that affords high accuracy and a high search speed when determining robust optimal solutions. To ensure the robustness of the determined optimal solution, RePSO employs the rate of change of the cost function. When this rate is high, the cost function appears as a steep curve, indicating low robustness; in contrast, when the rate is low, the cost function takes the form of a gradual curve, indicating high robustness. For verification, the performance of the proposed algorithm was compared with those of the conventional methods of robust particle swarm optimization and explorative particle swarm optimization with a Gaussian basis test function. The target performance of the traction motor for the optimal design was derived using a simulation of vehicle driving performance... [more]

The subsea production control system, characterized by a complex and diverse structure and high cost, is one of the essential parts of a subsea production system. The rational layout of the subsea production control system is essential to reduce development costs and ensure safe production in offshore fields. Most previous studies on layout design in offshore fields have focused on the oil- and gas-gathering system. However, the layout of the subsea production control system has not thoroughly been researched to date and the seabed terrain and integral optimization have rarely been discussed. This paper focuses on the multi-layer star structure and multi-layer star-tree structure, two common layout structures of subsea production control systems, and establishes the corresponding model with obstacle and seabed terrain conditions. Obtaining the lowest possible total cost was the aim of the model. A hybrid algorithm combining the adaptive mutation particle swarm algorithm and the A-star... [more]

Every year, large amounts of selective catalytic reduction (SCR) catalysts with losing catalytic activity and failing to be regenerated need to be regenerated, which will result in acute pollution. Recycling valuable metals from spent SCR catalysts can not only solve environmental problems, but also save resources. The process of sodium roasting and water leaching is able to effectively extract vanadium (V) and tungsten (W) from spent SCR catalysts. To improve the efficiencies of V and W, different sodium additives were first investigated in the roasting process. The results revealed that the process of NaCl-NaOH composite roasting and water leaching showed superior leaching efficiencies of V and W, which can reach 91.39% and 98.26%, respectively, and simultaneously, it can be found that adding low melting point NaOH promoted mass transfer as compared with the melting points of different sodium additives. Next, a single-factor experiment was conducted to investigate different roasting... [more]

In this paper, internal division point genetic algorithm (IDP-GA) was proposed to lessen the computational burden of multi-variable multi-objective optimization problem using finite element analysis such as optimal design of electric bicycles. The IDP-GA could consider various objectives with normalized weighted sum method and could reduce the number of function calls with novel crossover strategy and vector-based pattern search method. The superiority of the proposed algorithm was verified by comparing performances with conventional optimization method at two mathematical test functions. Finally, the applicability of the IDP-GA in practical electric machine design was verified by successfully deriving an improved design of electric bicycle propulsion motor.

The effective separation of CO2 and CH4 mixtures is essential for many applications, such as biogas upgrading, natural gas sweetening or enhanced oil recovery. Membrane separations can contribute greatly in these tasks, and innovative membrane materials are being developed for this gas separation. The aim of this work is the evaluation of the potential of two types of highly CO2-permeable membranes (modified commercial polydimethylsiloxane and non-commercial ionic liquid−chitosan composite membranes) whose selective layers possess different hydrophobic and hydrophilic characteristics for the separation of CO2/CH4 mixtures. The study of the technical performance of the selected membranes can provide a better understanding of their potentiality. The optimization of the performance of hollow fiber modules for both types of membranes was carried out by a “distance-to-target” approach that considered multiple objectives related to the purities and recovery of both gases. The results demonst... [more]

Electrochemical impedance spectroscopy (EIS) is an important electrochemical technique that is used to detect changes and ongoing processes in a given material. The main challenge of EIS is interpreting the collected measurements, which can be performed in several ways. This article focuses on the electrical equivalent circuit (EEC) approach and uses grammatical evolution to automatically construct an EEC that produces an AC response that corresponds to one obtained by the measured electrochemical process(es). For fitting purposes, synthetic measurements and data from measurements in a realistic environment were used. In order to be able to faithfully fit realistic data from measurements, a new circuit element (ZARC) had to be implemented and integrated into the SPICE simulator, which was used for evaluating EECs. Not only is the presented approach able to automatically (i.e., with almost no user input) produce a more than satisfactory EEC for each of the datasets, but it also can also... [more]