Recently, the use of diverse renewable energy resources has been intensively expanding due to their technical and environmental benefits. One of the important issues in the modeling and simulation of renewable energy resources is the extraction of the unknown parameters in photovoltaic models. In this regard, the parameters of three models of photovoltaic (PV) cells are extracted in this paper with a new optimization method called turbulent flow of water-based optimization (TFWO). The applications of the proposed TFWO algorithm for extracting the optimal values of the parameters for various PV models are implemented on the real data of a 55 mm diameter commercial R.T.C. France solar cell and experimental data of a KC200GT module. Further, an assessment study is employed to show the capability of the proposed TFWO algorithm compared with several recent optimization techniques such as the marine predators algorithm (MPA), equilibrium optimization (EO), and manta ray foraging optimization... [more]

Liquefied natural gas (LNG) is a clear and promising fossil fuel which emits less greenhouse gas (GHG) and has almost no environmentally damaging sulfur dioxide compared with other fossil fuels. An LNG import terminal is a facility that regasifies LNG into natural gas, which is supplied to industrial and residential users. Modeling and optimization of the LNG terminals may reduce energy consumption and GHG emission. A mixed-integer nonlinear programming model of the LNG terminal is developed to minimize the energy consumption, where the numbers of boil-off gas (BOG) compressors and low-pressure (LP) pumps are considered as integer variables. A case study from an actual LNG terminal is carried out to verify the practicality of the proposed method. Results show that the proposed approach can decrease the operating energy consumption from 9.15% to 26.1% for different seasons.

This study investigates the optimization of the hull form of a tanker, considering the operational efficiency in waves, in accordance with the recent Energy Efficiency Design Index regulation. For this purpose, the total resistance and speed loss of the ship under representative sea conditions were minimized simultaneously. The total resistance was divided into three components: calm water resistance, added resistance due to wind, and to waves. The first two components were calculated using regression formulas, and the last component was estimated using the strip theory, far-field method, and the short-wave correction formula. Next, prismatic coefficient, waterline length, waterplane area, and flare angle were selected as design variables from the perspective of operational efficiency. The hull form was described as a combination of cross-sectional curves. A combination of the method shifting these sections in the longitudinal direction and the Free-Form Deformation method was used to... [more]

The production of heterologous proteins for medical use is an important area of interest. The optimization of the bioprocesses includes the improvement of time, costs, and unit operations. Our study shows that a lectin fraction from Tepary bean (Phaseolus acutifolius) (TBLF) has cytotoxic effects on colon cancer cells and in vivo antitumorigenic activity. However, the low-yield, time-consuming, and expensive process made us focus on the development of a strategy to obtain a recombinant lectin using engineered Pichia pastoris yeast. Pure glycerol is one of the most expensive supplies; therefore, we worked on process optimization using crude glycerol from biodiesel production. Recombinant lectin (rTBL-1) production and purification were evaluated for the first time by an experimental design where crude glycerol (G65) was used and compared against pure glycerol (G99) in a controlled stirred-tank bioreactor with a fed-batch system. The recombinant lectin was detected and identified by SDS-... [more]

Traditionally, methanol is produced in large amounts from synthesis gas with heterogeneous Cu/ZnO/Al2O3 catalysts under steady state conditions. In this paper, the potential of alternative forced periodic operation modes is studied using numerical optimization. The focus is a well-mixed isothermal reactor with two periodic inputs, namely, CO concentration in the feed and total feed flow rate. Exploiting a detailed kinetic model which also describes the dynamics of the catalyst, a sequential NLP optimization approach is applied to compare optimal steady state solutions with optimal periodic regimes. Periodic solutions are calculated using dynamic optimization with a periodicity constraint. The NLP optimization is embedded in a multi-objective optimization framework to optimize the process with respect to two objective functions and generate the corresponding Pareto fronts. The first objective is the methanol outlet flow rate. The second objective is the methanol yield based on the total... [more]

The demand for safety and to provide safety are increasing, parallel with the growth of the need for mobility, transport and logistics. A big part of the demands and recommendations to provide safety in air traffic is related to the safety at and in the surroundings of the runways. The research focused on exploring the airport infrastructure; mainly with the aim of detecting and monitoring the deformations (cracks, displacements, etc.) of the runways which are causally connected with unusual landings or taking offs, with trips from the runways and with loss of control over the aircraft during the landings, taking offs and while moving the runways or taxiways, etc., and researching their effect on providing safety and the efficiency of the airports’ function. The research was executed at the Maribor Edvard Rusjan Airport in three phases; the first two were meant for geodetic measurements to determine vertical deformations and the third for supplementary measurements to determine static... [more]

The renewable energy microgrid is an effective solution for island energy supply with the advantages of low energy cost, environmental protection, and reliability. In this paper, an island renewable energy microgrid integrated with desalination units and electric vehicles is established to meet the self-satisfaction of the island’s sustainable electricity, fresh water, and transportation. The source side components of the system include photovoltaic cells, wind turbines, diesel generators, battery energy storage systems. A multi-objective dispatching optimization method based on the flexibility of electric vehicles and desalination units is proposed comprehensively considering the economy and renewable energy penetration indexes. The optimization objectives are minimizing the comprehensive operating cost, and the net load fluctuation. An improved multi-objective grey wolf optimizer is adopted to solve the dispatching problem. The system is modeled and simulated by MATLAB software. The... [more]

This study aimed to optimize the texture modification process of yellowfin sole (Pleuronectes aspera) to improve its quality characteristics for easier consumption by the elderly. Yellowfin sole was immersed in enzyme solution (Protamex:Neutrase = 1:2), marinated in herbal extract solution, and roasted by superheated steam. The product was evaluated for microbial, physicochemical, and sensory properties, as well as shelf life. Specifically, the optimal enzymatic treatment comprised a protease concentration of 1.00% (w/v) with an immersion time of 3.16 h. The optimal marination herb was determined to be bay leaves, as indicated by highest overall acceptance. The texture modification process led to lower hardness and higher overall acceptance values (76.23 kN/m2 and 8.38, respectively) compared with nonenzyme processed product (120.43 kN/m2, 7.43), also retaining high nutritional value and low trimethylamine levels. Shelf-life analysis indicated microbial activity was inhibited (not dete... [more]

The quality of product and process is one of the most important factors in achieving constructively and then functionally safe products in any industry. Over the years, the concept of Industry 4.0 has emerged in all the quality processes, such as nondestructive testing (NDT). The most widely used quality control methods in the industries of mechanical engineering, aerospace, and civil engineering are nondestructive methods, which are based on inspection by detecting indications, without affecting the surface quality of the examined parts. Over time, the focus has been on research with the fourth generation in nondestructive testing, i.e., NDT 4.0 or Smart NDT, as a main topic to ensure the efficiency and effectiveness of the methods for a safe detection of all types of discontinuities. This area of research aims at the efficiency of methods, the elimination of human errors, digitalization, and optimization from a constructive point of view. In this paper, we presented a magnetic partic... [more]

The numerical solution of the dynamic optimization problem is often sought for chemical processes, but the discretization of control variables is a difficult problem. Firstly, based on the analysis of the seagull optimization algorithm, this paper introduces the cognitive part in the process of a seagull’s attack behavior to make the group approach the best position. Secondly, the algorithm adds the mechanism of natural selection, where the fitness value is used to sort the population, and the best half is used to replace the worst half, so as to find out the optimal solution. Finally, the improved seagull optimization algorithm (ISOA) is combined with the unequal division method to solve dynamic optimization problems. The feasibility of the method is verified by three practical examples of dynamic optimization in chemical industry.

Nowadays, ever-increasing energy demands and the depletion of fossil fuels require efficient and environmentally friendly technologies for energy generation. In this context, energy systems integration makes for a very strong proposition since it results in energy saving, fuel diversification, and the supply of cleaner energy. To this end, it is of the utmost importance to realize the current developments in this field and portray the state of the art of renewable generation in integrated energy systems. This review evaluates the utilization of bioenergy in cogeneration and trigeneration systems. The statistical reports of bioenergy and combined heat and power deployments in 28 countries of the European Union are discussed. Then, the most common research objectives of biomass-fueled combined heat and power systems are classified into three primary performance analyses, namely, energy and exergy analysis, thermo-economic optimization, and environment assessment. The influencing paramete... [more]

In the present work, various objective functions were formulated and optimized using the mixed integer nonlinear programming and the generalized reduced gradient nonlinear method from the solver tool of Microsoft® Excel 2016, respectively. The CH3FO2, C2H4F2O, CH2F2O2, CH2F2O, C3H4F2, and the C2H2F2O molecules were found to meet structural feasibility constraints and physical properties from refrigerant molecules and have not previously been reported in the literature. These new refrigerants present global warming potential values similar to that from the R-134a and Freon 12 refrigerants and null ozone depletion potential. Moreover, these molecules are normally flammable, as similar as to R-134a refrigerant. The CH3FO2, C2H4F2O, CH2F2O2, C2H2F2O, and CH2F2O show toxicity values similar to R-134a and Freon 12 refrigerants.

The research on malware detection enabled by deep learning has become a hot issue in the field of network security. The existing malware detection methods based on deep learning suffer from some issues, such as weak ability of deep feature extraction, relatively complex model, and insufficient ability of model generalization. Traditional deep learning architectures, such as convolutional neural networks (CNNs) variants, do not consider the spatial hierarchies between features, and lose some information on the precise position of a feature within the feature region, which is crucial for a malware file which has specific sections. In this paper, we draw on the idea of image classification in the field of computer vision and propose a novel malware detection method based on capsule network architecture with hyper-parameter optimized convolutional layers (MalCaps), which overcomes CNNs limitations by removing the need for a pooling layer and introduces capsule layers. Firstly, the malware... [more]

Bio-based levulinic acid (LA), furfural (FF), and hydroxymethylfurfural (HMF) represent key chemical intermediates when biorefining biomass resources, i.e., either cellulose, glucose, hexoses, etc. (HMF/LA), or hemicellulose, xylose, and pentose (FF). Despite their importance, their online in situ detection by process analytical technologies (PATs), solubility, and its temperature dependence are seldom available. Herein, we report their solubility and temperature dependence by examining n-hexane, cyclohexane, benzene, toluene, 1,4-dioxane, diethyl ether, dichloromethane, tetrahydrofuran, ethyl acetate, acetone, dimethylformamide, acetonitrile, dimethyl sulfoxide, formic acid, n-butanol, n-propanol, ethanol, methanol, and water. These solvents were selected as they are the most common nonpolar, polar aprotic, and polar protic solvents. Fourier-transform infrared (FTIR) spectroscopy was applied as a fast, accurate, and sensitive method to the examined solutions or mixtures. The latter al... [more]

Most real-world problems that have two or three objectives are dynamic, and the environment of the problems may change as time goes on. For the purpose of solving dynamic multi-objective problems better, two proposed strategies (second-order difference strategy and random strategy) were incorporated with NSGA-III, namely SDNSGA-III. When the environment changes in SDNSGA-III, the second-order difference strategy and random strategy are first used to improve the individuals in the next generation population, then NSGA-III is employed to optimize the individuals to obtain optimal solutions. Our experiments were conducted with two primary objectives. The first was to test the values of the metrics mean inverted generational distance (MIGD), mean generational distance (MGD), and mean hyper volume (MHV) on the test functions (Fun1 to Fun6) via the proposed algorithm and the four state-of-the-art algorithms. The second aim was to compare the metrics’ value of NSGA-III with single strategy an... [more]

To improve the comprehensive benefits of the CCHP system, this paper proposes a bi-level optimal configuration model of the CCHP system based on the improved FCM clustering algorithm. Firstly, based on the traditional FCM clustering algorithm, the entropy method is used to introduce the PFS index and the Vp index in a weighted form to achieve a comprehensive evaluation of the clustering effect. The effectiveness of the improved FCM algorithm is verified by analyzing the clustering process of the load and meteorological data using the improved FCM algorithm. Then the best cluster number and fuzzy coefficient is found using the traversal method. Secondly, a bi-level configuration optimization model is constructed. The outer layer is the configuration optimization layer, and the inner layer is the operation optimization layer. The model is solved by combining the NSGA-II and PSO algorithms. Finally, a bi-level optimal configuration model is constructed for actual cases, and the clustering... [more]

This paper reviews actual sustainability assessments in the construction sector to define whether and how a Life Cycle Sustainability Assessment (LCSA) is applied and interpreted in this sector today. This industry has large shares in global energy (33%), raw material consumption (40%) and solid waste generation (40%). Simultaneously, it drives the economy and provides jobs. The LCSA is a method to identify environmental, social and economic impacts of products/services along their life cycles. The results of this study showed a mismatch between sectoral emissions and the number of LCSA-based impact evaluations. It was found that only 11% of papers reviewed assessed all three sustainability pillars. The economic and especially the social pillars were partly neglected. In Life Cycle Assessments (LCAs), 100% made use of Global Warming Potential (GWP) but only 30% assessed more than five indicators in total. In Life Cycle Costing (LCC), there were a variety of costs assessed. Depreciation... [more]

A novel parametric control method for the compressor blade, the full-blade surface parametric method, is proposed in this paper. Compared with the traditional parametric method, the method has good surface smoothness and construction convenience while maintaining low-dimensional characteristics, and compared with the semi-blade surface parametric method, the proposed method has a larger degree of geometric deformation freedom and can account for changes in both the suction surface and pressure surface. Compared with the semi-blade surface parametric method, the method only has four more control parameters for each blade, so it does not significantly increase the optimization time. The effectiveness of this novel parametric control method has been verified in the aerodynamic optimization field of compressors by an optimization case of Stage35 (a single-stage transonic axial compressor) under multi-operating conditions. The optimization case has brought the following results: the adiabat... [more]

Centrifugal blood pumps have provided a powerful artificial support system for patients with vascular diseases. In the design process, geometrical optimization is usually needed to acquire a more biocompatible model for clinical uses. In the current paper, we propose a method for multi-objective optimization concerning both the hydraulic and the hemolytic performances of the pump based on the near-orthogonal array in which the traditional hemolysis index (HI) is replaced with the maximum scalar shear stress criteria to reduce the computation load. The method is demonstrated with the optimization of an extracorporeal centrifugal blood pump with an unshrouded impeller. CFD studies on the original and nine modified pump models are carried out. The calculated hydraulic performances of the optimized model are also compared against the experiments for validation of the numeric method, with an error of 3.6% at the original design point. The resulting blood pump with low maximum scalar shear s... [more]

Dividing-wall columns (DWCs) are intensified processes that have attracted industrial and academic attention due to the reduction in operating and installation costs compared to traditional distillation systems. Several methodologies are available for the design of DWCs. Most of them consist of three parts: an analysis of operating variables; an analysis of the structural design (topology); and an optimization of the resulting preliminary design. This paper aims to study three widely used design methodologies reported in the literature for DWCs, i.e., Triantafyllou and Smith (T&S), minimum vapor (Vmin), and Sotudeh and Shahraki (S&S) methods, along with their implementation on process simulators. A proposed modification to the S&S methodology is also presented. A comparison of the methods is carried out and rated against designs with minimum total annual costs. The analysis considers the effect of different structural design variables to initialize the design procedure with each method... [more]

The main purposes of this project are to assess and to optimize the solubility of carbon dioxide (CO2) in an aqueous 30 wt% monoethanolamine-tetrabutylphosphonium methanesulfonate (MEA-[TBP][MeSO3]) new hybrid solvent. In this study, the viscosity and density of aqueous MEA-[TBP][MeSO3] hybrid solvents containing different amounts of [TBP][MeSO4] were determined. Meanwhile, Fourier Transform-Infrared (FT-IR) Spectroscopy was used to determine the presence of carbamate in aqueous MEA-[TBP][MeSO3] to prove that CO2 was absorbed by aqueous MEA-[TBP][MeSO3]. Response Surface Methodology (RSM) based on central composite design (CCD) was used to design the experiments and explore the effects of three independent parameters on the solubility of CO2 in aqueous MEA-[TBP][MeSO3]. The three independent parameters are concentration of [TBP][MeSO3] (2−20 wt.%), temperature (30−60 °C) and pressure of CO2 (2−30 bar). The experimental data was found to fit a quadratic equation using multiple regressio... [more]

The prediction accuracy of support vector regression (SVR) is highly influenced by a kernel function. However, its performance suffers on large datasets, and this could be attributed to the computational limitations of kernel learning. To tackle this problem, this paper combines SVR with the emerging Harris hawks optimization (HHO) and particle swarm optimization (PSO) algorithms to form two hybrid SVR algorithms, SVR-HHO and SVR-PSO. Both the two proposed algorithms and traditional SVR were applied to load forecasting in four different states of Nigeria. The correlation coefficient (R), coefficient of determination (R2), mean square error (MSE), root mean square error (RMSE), and mean absolute percentage error (MAPE) were used as indicators to evaluate the prediction accuracy of the algorithms. The results reveal that there is an increase in performance for both SVR-HHO and SVR-PSO over traditional SVR. SVR-HHO has the highest R2 values of 0.9951, 0.8963, 0.9951, and 0.9313, the lowes... [more]

Preload optimization is very important for ultrasonic motors’ design and application. In this paper, a novel method for a traveling-wave rotary ultrasonic motor is proposed. Firstly, based on linear regression and the analytic hierarchy process (AHP), the mapping between the drive characteristics, mechanical characteristics, speed stability, and preload of the traveling-wave-type rotary ultrasonic motor was established. Then, the characteristic curves of stalling torque, no-load speed, maximum efficiency, and speed stability with the change of preload method were measured with a new test platform. Finally, three traveling-wave rotary ultrasonic motors with optimized preload were used in a cooperative manipulator for validation. The experimental results showed that when the preload was optimized from 200 N to 310 N, the stalling torque of the motor increased by 20.7%, the maximum efficiency increased by 15.3%, the standard deviation of the speed decreased by 53.8%, and the no-load speed... [more]

One of the most crucial aspects of image segmentation is multilevel thresholding. However, multilevel thresholding becomes increasingly more computationally complex as the number of thresholds grows. In order to address this defect, this paper proposes a new multilevel thresholding approach based on the Evolutionary Arithmetic Optimization Algorithm (AOA). The arithmetic operators in science were the inspiration for AOA. DAOA is the proposed approach, which employs the Differential Evolution technique to enhance the AOA local research. The proposed algorithm is applied to the multilevel thresholding problem, using Kapur’s measure between class variance functions. The suggested DAOA is used to evaluate images, using eight standard test images from two different groups: nature and CT COVID-19 images. Peak signal-to-noise ratio (PSNR) and structural similarity index test (SSIM) are standard evaluation measures used to determine the accuracy of segmented images. The proposed DAOA method’s... [more]

The “Drying-redissolution” method is promising for the industrial production of high-concentration well-dispersed graphene oxide slurry (GOS). As the potential key step in this method, the spray drying process requires a statistical investigation which guides the large-scale preparation of graphene oxide powder (GOP). This work systematically studies the effects of operating parameters, including nozzle airflow rate (439−895 L·h−1), atomization pressure (0.5−0.7 MPa), and liquid feed rate (3.0−9.0 mL·min−1), by using the response surface methodology integrated Box−Behnken design (RSM−BBD), aiming to produce GOP with high yield and easy re-dispersion. The optimized spray drying condition is predicted to be 439 L·h−1, 0.59 MPa, and 9.0 mL·min−1, at which a powder yield of 70.45% can be achieved. The experimentally obtained GOP has an average particle size of 11.65 μm and the low crumpling degree of the particle morphology results in the good re-dispersibility (97.95%) and excellent adsor... [more]