Solar heat, already captured by vast asphalt fields in urban areas, is potentially a huge energy resource. The vertical soil temperature profile, i.e., low enthalpy geothermal energy, reveals how efficiently the irradiation is absorbed or radiated back to the atmosphere. Measured solar irradiation, heat flux on the asphalt surface and temperature distribution over a range of depths describe the thermal energy from an asphalt surface down to 10 m depth. In this study, those variables were studied by long-term measurements in an open-air platform in Finland. To compensate the nighttime heat loss, the accumulated heat on the surface should be harvested during the sunny daytime periods. A cumulative heat flux over one year from asphalt to the ground was 70% of the cumulative solar irradiance measured during the same period. However, due to the nighttime heat losses, the net heat flux during 5 day period was only 18% of the irradiance in spring, and was negative during autumn, when the soil... [more]

Nowadays, actuator line method (ALM) has become the most potential method in wind turbine simulations, especially in wind farm simulations and fluid-structure interaction simulations. The regularization kernel, which was originally introduced to ALM to avoid numerical singularity, has been found to have great influence on rotor torque predictions and wake simulations. This study focuses on the effect of each parameter used in the standard kernel and the anisotropic kernel. To validate the simulation, the torque and the wake characteristics of a model wind turbine were measured. The result shows that the Gaussian width ϵ (for standard kernel) and the parameter in chord length direction ϵc (for anisotropic kernel) mainly affect the normal velocity of each blade element when using ALM but have little effect on the tangential velocity calculation. Therefore, these parameters have great influence on the attack angle and rotor torque prediction. The thickness parameter ϵ t is the m... [more]

Laminar free convection heat transfer from a heated cylinder and tube arrays is studied numerically to obtain the local and average Nusselt numbers. To verify the numerical simulations, the Nusselt numbers for a single cylinder were compared to other authors for the Rayleigh numbers of 103 and 104. Furthermore, the vertically arranged heated tube arrays 4 × 1 and 4 × 2 with the tube ratio spacing SV/D = 2 were considered, and obtained average Nusselt numbers were compared to the existing correlating equations. A good agreement of the average Nusselt numbers for the single cylinder and the bottom tube of the 4 × 1 tube array is proved. On the other hand, the bottom tubes of the 4 × 2 tube array affect each other, and the Nusselt numbers have a different course compared to the single cylinder. The temperature fields for the tube array 4 × 4 in basic, concave, and convex configurations are studied, and new correlating equations were determined. The simulations were done for the Rayleigh n... [more]

For the first time, a study has been carried out on the pyrolysis of wood residues from Pinus pseudostrobus, Pinus leiophylla and Pinus montezumae, from an area in Western México using TGA analysis to determine the main kinetic parameters (Ea and Z) at different heating rates in a N2 atmosphere. The samples were heated from 25 °C to 800 °C with six different heating rates 5−30 °C min−1. The Ea, was calculated using different widely known mathematical models such as Friedman, Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose. The Ea value of 126.58, 123.22 and 112.72 kJ/mol (P. pseudostrobus), 146.15, 143.24 and 132.76 kJ/mol (P. leiophylla) and 148.12, 151.8 and 141.25 kJ/mol (P. montezumae) respectively, was found for each method. A variation in Ea with respect to conversion was observed with the three models used, revealing that pyrolysis of pines progresses through more complex, multi-stage kinetics. FT-IR spectroscopy was conducted to determine the functional groups present in the thre... [more]

The present work evaluates the application of regenerative braking for energy recovery in diesel-electric freight trains to increase efficiency and to improve decarbonization. The energy from regenerative braking has to be stored onboard when the track is not electrified. Different technologies of energy recovery are presented and discussed. The energy balance of an existing route is presented and simulated for different battery sizes. The analysis is illustrated with experimental data from an important Brazilian railway. Results show that the energy recovery from regenerative brake is a feasible investment and may be recommended to increase the efficiency in transportation and also to improve the low carbon mobility in railway systems.

Post-fracturing well shut-in is traditionally due to the elastic closure of hydraulic fractures and proppant compaction. However, for shale gas wells, the extension of shut-in time may improve the post-fracturing gas production due to formation energy supplements by fracturing-fluid imbibition. This paper presents a methodology using numerical simulation to simulate the hydrodynamic equilibrium phenomenon of a hydraulically fractured shale gas reservoir, including matrix imbibition and fracture network crossflow, and further optimize the post-fracturing shut-in time. A mathematical model, which can describe the fracturing-fluid hydrodynamic transport during the shut-in process, and consider the distinguishing imbibition characteristics of a hydraulically fractured shale reservoir, i.e., hydraulic pressure, capillarity and chemical osmosis, is developed. The key concept, i.e., hydrodynamic equilibrium time, for optimizing the post-fracturing shut-in schedule, is proposed. The fracturing... [more]

Climate change is one of the most important global problems faced by the international community. It is generally believed that increasing the consumption of renewable energy is an effective measure to promote CO2 emissions reduction. Therefore, renewable energy consumption has become one of the best alternative strategies for sustainable development. Based on this, this paper employs the 3SLS model to conduct an empirical study on the relations among real output, renewable energy consumption, and CO2 emissions of BRICS countries (except Russia) in 1999−2014. The empirical results support, for BRICS group, the complete tri-variate relationships (energy-output-emission nexus), and renewable energy had a significant positive impact on the real output, and vice versa. Besides, compared with other countries, Brazil also has the same tri-variate relationships as BRICS group. However, China has no relationship from real output to renewable energy consumption and from real output to CO2 emiss... [more]

The definition of appropriate energy targets for large industrial processes is a difficult task since operability, safety and plant layout aspects represent important limitations to direct process integration. The role of heat exchange limitations in the definition of appropriate energy targets for large process sites was studied in this work. A computational framework was used which allows to estimate the optimal distribution of process stream heat loads in different subsystems and to select and size a site wide utility system. A complex Swedish refinery site is used as a case study. Various system aggregations, representing different patterns of heat exchange limitations between process units and utility configurations were explored to identify trade-offs and bottlenecks for energy saving opportunities. The results show that in spite of the aforementioned limitations direct heat integration still plays a significant role for the refinery energy efficiency. For example, the targeted h... [more]

An experimental study was carried out to explore the heat transfer characteristics on the outside of smooth and enhanced tubes, during evaporation and condensation of R134A in the annulus of a tube-in-tube heat exchanger. The three-dimensional enhanced surface tube consisted of primary enhancement patterns and secondary patterns; results were compared to the performance of an equivalent smooth tube. The equivalent external diameter of the inside horizontal copper tubes used in this study was 19.05 mm, while the outer tube varied in size, allowing a comparison of heat transfer for different annulus dimensions. Tests were conducted with a fixed inlet/outlet vapor quality and a constant saturation temperature for varied mass velocities in the range of 30 to 100 kg/(m2∙s). For condensation, the ratio of heat transfer coefficient enhancement (enhanced tube/ smooth tube) was up to 1.78; this can be attributed to the turbulence increase, as well as liquid film re-distribution, produced from t... [more]

Due to the strengthening of air-quality regulations, researchers have been investigating methods to improve excavator energy efficiency. Many researchers primarily conducted simulation studies employing mathematical models to analyze the energy consumption of excavator systems, which is necessary to examine the fuel efficiency improvement margin and the improvement effect. However, to effectively study the improvement of excavator efficiency, the real-time energy consumption characteristics must be examined through simulations and analyses of actual equipment-based energy consumption. Accordingly, this study establishes an energy flow-down model for the entire excavator system based on actual equipment tests. A measurement system is built to measure the required data, thereby establishing an experimental methodology for modeling each component. This paper presents an excavator system energy flow-down methodology that integrates the energy flow-down model, measurement system, and experi... [more]

In an effort to improve the energy efficiency of existing buildings, it is necessary to first evaluate the energy performance of those buildings. Since it is difficult to obtain detailed information on existing buildings, the challenge is how to conduct reliable energy performance assessments with this limited information. As a result, many countries have adopted evaluation systems based on measured energy consumption data for existing buildings. This study aims to analyze the building energy consumption and characteristics using Korea’s national building database and provide an energy performance benchmark for continuous management of the energy performance of existing buildings. We analyzed the relationship between the basic statistical characteristics of the information collected from the national integrated energy database and energy consumption. The total floor area was found to be closely related to energy consumption, and various regression analysis methods were applied and comp... [more]

For the purpose of collecting solar radiation for energy conversion and utilization and improving the output performance of thermoelectric power-generation components, a new solar thermoelectric conversion device based on an all-glass solar heat transfer pipe and gravity-assisted heat pipe with recycling air cooling and water cooling circuits is designed. The uniqueness of the device lies in the combination of gravity-assisted heat pipes with excellent thermal conductivity and a direct air-cooled mode, a fin-cooled mode, and two solar-driven water-cooling modes with different flow rates. Based on the structure, the device can realize four separate output modes and multiple composite output modes and has practical significance for meeting different load power requirements, such as wireless sensors and electronics. Under a state of regular illumination from 3.14 × 104 lx to 10.04 × 104 lx, with one thermoelectric power generator (TEG) in one mode, the peak output voltage and power values... [more]

This paper aims to present a comparative study into the cascade and series configurations of the organic Rankine cycle based small-scale solar combined cooling, heating and power system for civil application. The energy performance of the systems is studied by developing a thermodynamic model. The simulation model is validated using the literature results. Analyses of the research results indicated that the cascade system can achieve maximum value of the primary energy efficiency of 13.4% for cooling and power generation under solar collecting temperature of 115 °C in cooling mode. The cascade system has more cooling output and less electricity output in cooling mode compared with the series system. In heating mode, the single solar organic Rankine cycle (ORC) operation can achieve highest primary energy efficiency of 19.6% for heating and power generation under solar collecting temperature of 100 °C. Systems with R141b as ORC working fluid show better performance than those with R123... [more]

The high consumption of firewood in Honduras necessitates the search for alternatives with less-negative effects on health, the economy, and the environment. One of these alternatives has been the promotion of improved cooking stoves, which achieve a large reduction in firewood consumption. This paper presents a cost-benefit analysis for an improved cooking stove adoption strategy for Honduras. The methodology uses the Long-range Energy Alternatives Planning System, LEAP, a tool used globally in the analysis and formulation of energy policies and strategies. The energy model considers the demand for firewood as well as the gradual introduction of improved cooking stoves, according to the premises of a National Strategy for improved cooking stoves adoption in Honduras. Hence, it is demonstrated that the costs of implementing this adoption strategy are lower than the costs of not implementing it, taking into consideration representative scenarios up to and including the year 2030.

Electrochemical impedance spectroscopy (EIS) is a powerful tool for investigating electrochemical systems, such as lithium-ion batteries or fuel cells, given its high frequency resolution. The distribution of relaxation times (DRT) method offers a model-free approach for a deeper understanding of EIS data. However, in lithium-ion batteries, the differential capacity caused by diffusion processes is non-negligible and cannot be decomposed by the DRT method, which limits the applicability of the DRT method to lithium-ion batteries. In this study, a joint estimation method with Tikhonov regularization is proposed to estimate the differential capacity and the DRT simultaneously. Moreover, the equivalence of the differential capacity and the incremental capacity is proven. Different types of commercial lithium-ion batteries are tested to validate the joint estimation method and to verify the equivalence. The differential capacity is shown to be a promising approach to the evaluation of the... [more]

The article presents the methodology of conducting serial laboratory measurements of thermal conductivity of recompacted samples of cohesive and non-cohesive soils. The presented research procedure has been developed for the purpose of supplementing the Engineering−Geology Database and its part−Physical and Mechanical Properties of Soils and Rocks (abbr. BDGI-WFM) with a new component regarding thermal properties of soils. The data contained in BDGI-WFM are the basis for the development of maps and plans for the assessment of geothermal potential and support for the sustainable development of low enthalpy geothermal energy. Effective thermal conductivity of soils was studied at various levels of water saturation and various degrees of compaction. Cohesive soils were tested in initial moisture content and after drying to a constant mass. Non-cohesive soils were tested in initial moisture, fully saturated with water and after drying to a constant mass. Effective thermal conductivity of n... [more]

The aim of this paper is to present the design and modeling of a machine that possesses some advantageous characteristics for wind energy conversion applications. The studied machine is a double stator inner rotor axial airgap flux switching permanent magnet machine (AFSPM). The paper will start by presenting this type of machine and its points of interest. Then, it will continue by introducing the constructed prototype and its specifications and structure. This prototype has been designed based on a reference specification used at GREAH to develop different prototypes and compare their performances. The second part will introduce the reluctance network model specifically constructed for this type of machine. The constructed model was validated by comparing its results to the results from the finite element method model. Finally, the experimental results will be presented and compared to the reluctance network (RN) model results where satisfying agreement between both results was obtai... [more]

In this study, reverse electrodialysis power generation using an anisotropic anodic aluminum oxide membrane with nanopores of two different pore diameters is proposed and experimentally investigated for the first time. A number of experiments were carried out for various combinations of concentrations to show that the anisotropic anodic aluminum oxide membrane is superior to the conventional isotropic membrane. As a result, the highest power density that was measured from the anisotropic membrane was 15.0 mW/m2, and it was 7.2 times higher than that from the isotropic membrane. The reasons why the anisotropic membrane is superior to the isotropic membrane are explained in detail. The experiments on the anisotropic membranes with various active layer lengths and pore diameters were also conducted for exploring the effects of these engineering parameters on the power generation performance. As a result, it was shown that the length of the active layer is a more important engineering para... [more]

Electric air-conditioning systems driven by electricity from a wind turbine can be defined as wind electric and cooling systems according to the definition of solar-activated air-conditioners. They can potentially contribute to reduce primary energy demand and CO2 emission in the civil sector. In this paper, mini wind turbines are considered coupled with a ground source heat pump in order to serve an office building for air-conditioning and supply the electricity surplus for the pure electric load of the user. Different plant configurations are considered. First of all, assessments with two kinds of wind turbines (5−5.5 kW), vertical and horizontal axis, are performed, also considering the coupling with one and two identical wind generators. Secondly, to better use on-site electricity, a parametric study is proposed taking into account different battery storage system sizes (3.2−9.6 kWh). Finally, the plant is simulated in two locations: Naples and Cagliari. Simulation results demonstr... [more]

Climate change is becoming more important day after day. The main actor to decarbonize the economy is the building stock, especially in the energy used for Domestic Hot Water (DHW), heating and cooling. The use of renewable energy sources to cover space conditioning and DHW demands is growing every year. While solar thermal energy can cover building heating and DHW demands, there is no technology with such potential and development for space cooling. In this paper, a new concept of combining radiative cooling and solar thermal collection, the Radiative Collector and Emitter (RCE), through the idea of an adaptive cover, which uses different material properties for each functionality, is for the first time experimentally tested and proved. The RCE relies on an adaptive cover that uses different material properties for each functionality: high spectral transmittance in the solar radiation band and very low spectral transmittance in the infrared band during solar collection mode, and high... [more]

Power generation from wind farms is traditionally modeled using power curves. These models are used for assessment of wind resources or for forecasting energy production from existing wind farms. However, prediction of power using power curves is not accurate since power curves are based on ideal uniform inflow wind, which do not apply to wind turbines installed in complex and heterogeneous terrains and in wind farms. Therefore, there is a need for new models that account for the effect of non-ideal operating conditions. In this work, we propose a model for effective axial induction factor of wind turbines that can be used for power prediction. The proposed model is tested and compared to traditional power curve for a 2.5 MW horizontal axis wind turbine. Data from supervisory control and data acquisition (SCADA) system along with wind speed measurements from a nacelle-mounted sonic anemometer and turbulence measurements from a nearby meteorological tower are used in the models. The res... [more]

In recent years, due to stringent emission regulations vehicle manufacturers have been compelled to cut down noxious pollutants released from diesel engines. Different alternative solutions have been recommended to achieve this challenging task. One of these alternative solutions is the utilization of biogas in addition to the use of liquid diesel. In this regard, the current study investigates the combustion characteristics and exhaust emissions of a turbocharged, direct injection, diesel engine operating at constant speed (1800 rpm) and under dual fuel mode with diesel as the pilot fuel and biogas (generated from pig manure and corn straw) and methane enriched biogas. Simulations were carried out at four various engine loads corresponding to brake mean effective pressure (BMEP) of 0.425, 0.85, 1.275, and 1.7 MPa using GT-Power package. The BTE values of biogas-diesel were higher as compared to diesel fuel. The CO2 ratio of biogas did not impact BTE considerably. The highest BTE value... [more]

An energy-management system requires accurate prediction of the electric load for optimal energy management. However, if the amount of electric load data is insufficient, it is challenging to perform an accurate prediction. To address this issue, we propose a novel electric load forecasting scheme using the electric load data of diverse buildings. We first divide the electric energy consumption data into training and test sets. Then, we construct multivariate random forest (MRF)-based forecasting models according to each building except the target building in the training set and a random forest (RF)-based forecasting model using the limited electric load data of the target building in the test set. In the test set, we compare the electric load of the target building with that of other buildings to select the MRF model that is the most similar to the target building. Then, we predict the electric load of the target building using its input variables via the selected MRF model. We combi... [more]

Industrial low-temperature processes are a promising sector for the introduction of solar collectors, which can partially, and in some cases, completely, replace traditional heat supply technologies. In Krasnodar Region (Russia), it is shown that the energy-saving potential when introducing industrial solar collectors only at food industry enterprises can make up 16%−17% of the total amount of thermal energy produced in the region annually. The global market of industrial solar collectors is currently developing almost without any government incentives, only due to market mechanisms, which indicates the commercial attractiveness of the technology. According to the predicted estimates, levelized cost of energy produced by industrial solar collectors in the southern regions of Russia may amount to 3.8−6.6 rubles per kWh. Even though the forecast estimates are higher than current tariffs, the economic feasibility of using solar collectors in the industry increases significantly if it is n... [more]

Myanmar remains one of the few exceptions to the rapid diffusion of solar photovoltaics (PV) in power generation mixes. This is surprising considering that Myanmar is one of the countries with the largest technical potential for solar energy among Southeast Asian nations. Solar energy can complement the existing hydropower generation to address endemic energy crisis during the dry season. A continuation of paralysis on investments in solar energy could affect the security and sustainability of the sector in one of the most rapidly growing countries in the region. In this paper, we aimed to identify the barriers preventing solar energy to flourish in Myanmar and to identify policy options to unlock them. We conducted a SWOT (strengths, weaknesses, opportunities, and threats) analysis with inputs from relevant stakeholders from the government, private sector, and civil society organizations. Our analysis suggested a consensus on the merits of solar energy among all factors; however, a po... [more]