Conventional fluid loss additives have difficultly controlling the water loss of cement−metakaolin slurry with semi-saturated brine cement slurry and limiting it to less than 50 mL (30 min)−1. This paper describes the development of an anti-salt fluid loss additive for metakaolin−cement systems. This study adopted the aqueous solution polymerization method; selected four kinds of monomers, namely 2-Acrylamido-2-methylpropane sulfonic acid (AMPS), N,N-Dimethylacrylamide (DMAA), acrylamide (AM), and methyl acrylate (MA); and performed a single-factor experiment on the proportion of monomer, reaction temperature, initiator dosage, and developed fluid loss additive, which has a high salt tolerance and temperature tolerance. This fluid loss additive can resist salt until saturation, and it can control fluid loss in 24 mL·(30 min)−1 when its dosage is 2%. The fluid loss additive can achieve the effect of fluid loss reduction by increasing the filtrate viscosity, forming a flexible elastic ad... [more]

Improving diesel engine performance requires a comprehensive understanding of fuel atomization and air−fuel mixing within the combustion chamber. Numerous studies have been conducted to reduce emissions and enhance diesel engines. However, further investigation is required on the detailed diesel spray process. In this study, we adopted extinction measurement to analyze the effects of a fuel injection pressure range of 300 to 700 bar on spray morphology. For the extinction imaging setup, we utilized a high-intensity continuous LED source along with a diffuser to ensure uniform light distribution. The high-speed extinction and image processing results indicate that increasing the injection pressure from 300 to 700 bar effectively produced a smaller particulate size (15% reduction) and a better air−fuel mixing process. Especially at the end of injection, our results show smaller liquid ligaments (50% reduction) and droplets around the injector tip with higher injection pressure cases.

Food waste, particularly animal-derived waste, presents a significant challenge globally, prompting the need for sustainable management strategies. In 2022, the amount of food waste per capita reached 131 kg/capita in the EU (European Union), which is why the search for environmentally friendly ways to manage food waste through thermochemical conversion processes has gained momentum in recent years. Animal-derived waste is a good source of organic matter (proteins, lipids, and polysaccharides) and mineral compounds (calcium phosphate, mostly hydroxyapatite). This composition makes animal-derived waste valuable for the extraction of chemical compounds, such as hydroxyapatite (HAp), which constitutes up to 70 wt% of animal bones; keratin; collagen; and hyaluronic acid (HA), to produce pharmaceutical, medical, or industrial by-products. The thermochemical conversion of chicken bones through pyrolysis and gasification creates a new opportunity to valorize this type of waste by reintroducin... [more]

Since the discovery of the vast Jimusaer shale oilfield in the southeastern Junggar Basin in 2012, there has been considerable interest in neighboring areas around Bogeda Mountain that have shale oil potential. The primary productive interval in the basin, the Middle Permian Lucaogou Formation (P2l), is well-developed in the areas of Qitai, Mulei, Shiqiantan, Chaiwopu, and Miquan. In this study, we conducted an assessment of the hydrocarbon generation potential of the P2l in these five areas and compared it with that of the P2l in the Jimusaer oilfield, which were determined by GC-MS, total organic carbon (TOC) and vitrinite reflectance (Ro) measurements, Rock-Eval pyrolysis, and organic petrology to investigate the type, origin, thermal maturity, hydrocarbon potential, and oil/gas proneness of organic matter in the P2l. Additionally, we applied open-system pyrolysis of hydrocarbon generation kinetics to explore differences in hydrocarbon generation and expulsion across various P2l mud... [more]

An experimental study and dimensional analysis of the effective heat transfer coefficient in a continuous-indirect rotatube dryer using forest biomass as the granular material isare developed in the present work. The study employed a factorial design 33 to investigate the effects of feed flow frequency (20−35−50 (Hz)), drum rotational velocity (6−8−10 (rpm)), and saturated vapor pressure (4−5−6 (bar)) on the heat transfer coefficient. During steady state conditions, the moisture content profiles and inlet and outlet temperatures were measured within the experimental region, and parameters, such as the effective heat transfer coefficient, solid retention change, and moisture content ratio were studied. The results showed that heat transfer was optimized with high solid feeding rates, low pressure, and low rotation, with solid feeding being the predominant factor. The moisture content profiles revealed a change in the hydrodynamic behavior, with the center point of the experimental regio... [more]

In July 2023, the International Maritime Organization (IMO) presented an updated strategy for decarbonizing maritime transport and achieving net-zero greenhouse gas emissions by 2050. It is therefore imperative to explore innovative solutions to achieve a blue economy and maximize energy efficiency on-board ships. For this reason, the current study aims to integrate the organic Rankine cycle (ORC) and thermoelectric generator (TEG) on board a container ship to generate electrical energy and reduce fuel consumption. The combined system will benefit from the waste heat of a marine diesel engine installed on board. The current study uses R245fa as the organic liquid and analyzes the effects of varying the evaporation pressure on the energetic and economic performance indicators by modeling the combined system in Engineering Equation Solver (EES) software. The results show that the energy efficiency of the ORC system increases from 12.3% at 3.5 bar to 17.3% at 8 bar. In comparison, the ene... [more]

Nonwoven fabrics with appropriate hydrophilicity and potent antimicrobial properties hold important promise for hygiene applications. However, existing materials with certain limitations and complex manufacturing steps, along with the unavoidable use of chemicals in the process, are limited to a certain extent in terms of the balance between comfort and antimicrobial properties. In this paper, a polyimide (PI) fiber was reported to be used for the preparation of PI composite nonwoven fabrics (5-P), which can effectively enhance the surface hydrodynamic and antimicrobial properties of the nonwoven by a one-step plasma treatment on one side. After treatment, the one-sided water contact angle (WCA) changed from 121.5° to 68.5°, and the permeation volume from 0.7 to 2.1 g, with a relative increase of 181.9%. Meanwhile, the reverse osmosis amount was only 0.5 g, achieving rapid permeation while keeping a low reverse osmosis amount. The antimicrobial experiment showed that plasma-treated 5-P... [more]

As the core power element of a centrifugal fan, the impeller’s structural parameters are important factors affecting the aerodynamic performance of the fan. Therefore, to improve the aerodynamic performance of centrifugal fans, in this study, we take the Powered Air-Purifying Respirator (PAPR) power system as the object of research and use a combination of computational fluid dynamics (CFD) and experimental validation to investigate the effects of the number of blades, blade inlet angle, blade outlet angle, blade height, and blade thickness on the aerodynamic performance of the fan. A five-factor, four-level orthogonal test table L16 (45) was selected to obtain the optimal combination of structural parameters for the impeller. In addition, in order to identify and visualize the features of the vortex, Q Criterion Normalized is applied to the simulation on the basis that the minimum pressure appears in the vortex core. In this study, Q Criterion Normalized is used to compare the interna... [more]

The focus of this review article is to present a retrospective analysis of copper applications focusing on ions and nanoparticles as broad-spectrum antimicrobials. Copper nanoparticles are presented as an alternative to rising antibiotic resistance. The basic mechanisms of bacterial, fungal, and viral inactivation, which explain their potential, are presented. The green biosynthesis of copper nanoparticles using biomaterials is also presented and considered a very promising trend for future biotechnology and medical applications.

Based on PetroChina’s status and situation of low-permeability oil reservoir development, this paper analyzes the key common issues in the production capacity construction of new oilfields, the stable production of old oilfields, and enhanced oil recovery, and, in connection with the progress made in major development technologies and the results of major development tests for low-permeability oil reservoirs in recent years, puts forward the technical countermeasures and development directions. For optimizing the development of low-grade reserves, a comprehensive life-cycle development plan is essential, alongside experimenting with gas injection and energy supplementation in new fields. Addressing challenges in reservoir classification, multidisciplinary sweet spot prediction, and displacement−imbibition processes can significantly boost well productivity. In fine water flooding reservoirs, the focus should shift to resolving key technological challenges like dynamic heterogeneity cha... [more]

Municipal wastewater treatment plants (WWTPs) are exposed to high concentrations of micropollutants that can impact conventional activated sludge treatment. The consequences of this include failure to meet discharge standards and the disintegration of flocs, leading to poor sludge settleability. This lab-scale study focuses on the influence of doxycycline, an antibiotic widely used against human and animal diseases, on protozoa, metazoa, and bacterial communities under sludge growing conditions. Doxycycline was added to the mixed liquor of a communal WWTP up to 0, 100, 200, and 400 mg of doxycycline L−1 and incubated in batch conditions for 23 days. The regular addition of nutrient and carbon sources was preformed every 2 days to prevent sludge starvation. Sludge growth, conductivity, and settleability were measured and compared to sludge microbial community structure, determined by microscopic observations and high-throughput 16S rDNA sequencing. The high doxycycline concentration neg... [more]

The widespread use of plastic materials poses significant environmental challenges, which have promoted a growing call for a circular approach to such materials, emphasizing waste reintegration into production. From this perspective, the present study focuses on analyzing a post-industrial recycled stream of chrome-plated automotive scraps composed of acrylonitrile−butadiene−styrene (ABS), polycarbonate (PC), and a commercial PC/ABS blend. The batch-to-batch varying proportions of these constituents make control of the recycled materials’ quality challenging. To address this problem, we formulated an I-optimal mixture design model using the infrared absorbance ratio of selected peaks and Izod impact resistance results for injection-molded samples as inputs to determine the composition of each batch quickly. The two model equations (adjusted R2 > 0.97) obtained, based on cubic expression and regressed from data obtained from 27 mixtures with known compositions, were combined into a sing... [more]

In some applications of microgrids and distributed generation, it is necessary to feed islanded or stand-alone loads with high-quality voltage to provide low total harmonic distortion (THD). To fulfil these demands, an LC filter is usuallyconnected to the output terminals of power electronics converters. A cascaded voltage and current control loop with pulse-width modulation schemes are used to regulate the voltages and currents in these systems. However, these strategies have some drawbacks, particularly when multiple-input−multiple-output plants (MIMO) are controlled using single-input−single-output (SISO) design methods. This methodology usually produces a sluggish transient response and cross−coupling between different control loops and state variables. In this paper, a model predictive control (MPC) strategy based on the concept of optimal switching sequences (OSS) is designed to control voltage and current in an LC filter connected to a three-level neutral-point clamped converter... [more]

In recent years, the development of two offshore low-permeability oil fields has revealed unexpected challenges. The actual productivity of these fields significantly deviates from the designed capacity. Some wells even outperform the expectations for low-permeability limestone fields. This discrepancy primarily stems from a lack of accurate understanding of natural fractures before and after drilling, resulting in substantial errors in capacity assessment. This paper addresses these challenges by proposing a new production capacity model and evaluation method for both vertical and horizontal wells in low-permeability limestone reservoirs. The method leverages logging curve data, incorporating vertical gradation and fractal analysis to effectively represent the fracture’s complexity and connectivity. It uniquely considers factors such as fracture fractal dimensions, threshold pressure, and stress sensitivity, significantly enhancing prediction accuracy. Furthermore, by analyzing the lo... [more]

With the proportion of renewable energy power in the electricity market gradually increasing, coal-fired power is transforming from primary to basic power, with it providing peak and frequency shaving. However, most current methods for peaking below 50% load have been applied industrially, sacrificing the efficiency of the unit. This is not in line with the goals of energy conservation and emission reduction. Therefore, this study proposes a new preheating-based peaking method. This study experimentally and simulatively explores the flow characteristics, pyrolysis gas law, and NOx emission characteristics of a preheating burner at 40−100% load. The results show that the burner has a significant preheating effect, producing high-temperature char and large amounts of pyrolysis gas. As the load decreases, the burner exit temperature increases, whereas the airflow stiffness decreases. There is little variation in the pyrolysis gas concentration between 40% and 100% loads. The NOx concentra... [more]

This study aimed to investigate the effect of combined Free Nitrous Acid (FNA)-Heat (i.e., FNH) pretreatment on single- and two-stage anaerobic digestion (AD) of thickened waste-activated sludge (TWAS). Single-stage AD was conducted in batches, while two-stage AD involved acidogenic fermentation under semi-continuous flow followed by batch methanogenesis. FNH pretreatment was applied before the acidogenic stage, using 1.4 mg HNO2-N/L FNA concentration at 25 °C, 37 °C, and 60 °C for 24 h. Among the scenarios, the most promising results were observed with two-stage AD fed with FNH-pretreated TWAS at 60 °C, showing higher COD solubilization and a reduction in volatile solids. Combined FNA-Heat pretreatment in two-stage AD yielded elevated methane production (363−415 mL CH4/g VS added) compared to single-stage digestion. Methane yields from FNA-Heat pretreated single-stage ranged from 332 to 347 mL CH4/g VS added, contrasting with 212 mL CH4/g VS added for untreated TWAS. Methane generatio... [more]

The coal mine ground gas transportation system is widely used for gas transportation and mixing preheating in the gas storage and oxidation utilization system. However, gas or coal dust explosions may occur, which could result in heavy casualties and significant economic losses. To prevent accidents in the gas transportation system, the present study takes the gas transportation system of Shanxi Yiyang Energy Company as an example to identify the composition and hazardous factors of the gas transportation system. Fault tree analysis (FTA) models were established with pipeline gas and coal dust explosions as the top events, and the importance of each basic event was quantitatively analyzed using the fuzzy fault tree analysis (FFTA) method. The results show that gas and coal dust explosion accidents are mostly caused by the combination of high-temperature ignition sources and explosive materials. The uneven mixing gas and the ventilation carrying a large amount of coal dust are the funda... [more]

Proteins are complex molecules, which play a vital role in our body’s function, the building of tissues, and the regulation of metabolic activity. They are crucial to children’s growth and serve as a key component in the body’s process of distributing oxygen. Proteins fuel the body by supplying the required nutrition and energy. Currently, there is an increasing demand for proteins on large scales with no detrimental effects. The adverse health effects of animal proteins have resulted in a growing preference for plant-based proteins, which offer a healthier daily dosage. Valuable proteins can be extracted from various parts of the plant, including stems, leaves, seeds, fruits, vegetables, and roots. Notably, protein extraction from waste plant and mushroom parts minimizes the product wastage and improves the overall production to support economic sustainability. There are several protein extraction techniques available, where the replacement of non-thermal methods with thermal ones is... [more]

This study explores the efficacy of 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide and 1-hexyl-3-methylimidazolium chloride as cleaning agents for aged cellulosic artifacts. A 10% v/v acetone solution of these ionic liquids (ILs) effectively removes the brownish-yellow color of aged paper in a 10 min immersion treatment. Colorimetric analysis shows a remarkable increase in lightness (L*) by up to 40% and a decrease in red/brownish tones (b*) after IL treatment. The cleaning process also deacidifies the paper, shifting the pH to neutral-slightly basic levels and enhancing its long-term stability. Optimal pH outcomes are achieved, with ionic liquid consumption values of 0.4−0.6 g/g of paper. The FTIR analysis revealed structural changes in cellulose induced by the washing step, which is mainly due to the reorganization effect imparted by the ionic liquids. Furthermore, ILs mobilized degraded compounds and acidic species, aiding in their extraction during the restoration pr... [more]

Iron and steel are regarded as the foundation for national development, but their processing consumes huge amounts of fossil fuel and produces large amounts of carbon dioxide gas, which is not conducive to the sustainable development of society [...]

The global concern regarding the release of micropollutants (MPs) into the environment has grown significantly. Considerable amounts of persistent micropollutants are present in industrial discharges. Depending solely on a singular treatment approach is inadequate for the effective removal of MPs from wastewater due to their complex composition. The performance of different treatment methods to meet the discharge standards has been widely studied. These efforts are classified as hybrid and sequential processes. Despite their adequate performance, the optimization and industrial application of these methods could be challenging and costly. This review focuses on integrated (sequential) and hybrid processes for MP removal from actual wastewater. Furthermore, to provide a thorough grasp of the treatment approaches, the operational conditions, the source of wastewater containing MPs, and its characteristics are detailed. It is concluded that the optimal sequence to achieve the removal of M... [more]

The ultra-low permeability oil reservoir in the HQ oilfield within the Ordos Basin exemplifies a classic “three-low” oil reservoir characterized by low pressure, low permeability, and low abundance. Upon the commencement of oil well production, substantial initial production decline and inadequate pressure maintenance levels are encountered. Consequently, these wells commonly face persistent low production issues resulting from ineffective water injection. Currently, the available technical approaches for repeated stimulation of such wells to enhance production and efficiency are limited, thereby restricting the effective utilization of the remaining oil reserves. In response to this challenge, this article presents an innovative technology tailored for high-efficiency re-fracturing to improve oil recovery in ultra-low permeability reservoirs. Grounded in the theory of multiple flow couplings and volume development, this technology introduces a novel integrated process encompassing see... [more]

The drying kinetics of porous media are crucial for controlling the drying process, which is a vital component in many processes. A mathematical model of the drying process in a granular bed was developed using Whitaker’s model, and its accuracy was verified through experimental results. The results indicated that the three stages of porous media drying are closely linked to the heat flow to the media and the latent heat of evaporation required by the liquid water inside it. Moreover, as the influence of gravity weakens and the capillary force strengthens, specifically due to the gradual decrease in the pore size of the bed, significant differences in the drying kinetics of the bed are observed, particularly in the third stage of drying, which is most affected. The onset of saturation in the third stage of bed drying varies with the pore size of the particles, with smaller pore sizes exhibiting an earlier onset. Additionally, the temperature change in this stage demonstrates the occurr... [more]

One of the latest tendencies in research related to material extrusion based on additive manufacturing is to determine the mechanical characteristics of parts taking into consideration the most influential manufacturing parameters. The main research objective is to describe how the manufacturing parameters, part orientation, layer thickness and infill density influence the tensile behavior of specimens made from PET with 15% short carbon fibers. The most advantageous result is obtained for a layer thickness of 0.15 mm, with 100% material infill, and material deposition on the longitudinal direction of the part. The obtained mean values are: 65.4 MPa tensile strength, 1.93% strain at rupture, and 9 GPa Young Modulus. For these values, the tensile behavior of specimens manufactured along transverse and thickness directions are presented. The least favorable results are obtained for manufacturing by thickness. The novelty of the discussed research consists in all these aspects together wi... [more]

To investigate the pressure pulsation characteristics of self-priming pumps under different flow conditions, Fluent 19.2 software was used to numerically calculate the internal flow inside a self-priming pump by means of the RNG k-ε model. The pressure pulsation characteristics, as well as the standard deviation in the volute and impeller domains, were analyzed under different flow conditions. As a result, under rated- and high-flow conditions, the monitoring points in the volute channel have obvious periodic patterns, and the peak pressure pulsations all occur in the octave band of the blade frequency. The pressure pulsation amplitude is larger under the high-flow condition than in the other two conditions. The monitoring points L1 and L5 on the impeller channel centerline are located near the impeller’s inlet and outlet, respectively, so the pressure pulsations are larger than other monitoring points.