Expired dairy products are often disposed of due to the potential health hazard they pose to living organisms. Lack of methods to recover valuable components from them are also a reason for manufactures to dispose of the expired dairy products. Milk encompasses several different components with their own functional properties that can be applied in production of food and non-food technical products. This study aims to investigate the novel approach of using liquid biphasic flotation (LBF) method for protein extraction from expired milk products and obtaining the optimal operating conditions for protein extraction. The optimized conditions were found at 80% concentration ethanol as top phase, 150 g/L dipotassium hydrogen phosphate along with 10% (w/v) milk as bottom phase, and a flotation time of 7.5 min. The protein recovery yield and separation efficiency after optimization were 94.97% and 86.289%, respectively. The experiment has been scaled up by 40 times to ensure it can be commerc... [more]

Fretting occurs during orthodontic treatment or wearing prosthesis. Although weight of particles is marginal, the total releasing area is more of a concern due to amount and volume of molecules. The aim of the study was to examine the fretting wear resistance of orthodontic and prosthetic alloy Ni-Cr-Mo samples coated with Ti(C, N) and to compare them with samples without any coating. Five groups of cylindrical shape samples (S1−S5) made of Ni-Cr-Mo were coated with Ti(C, N) layers with different content of C and N. The control group (S0) was without layer. The alloys underwent fretting wear resistance tests with amplitude 100 μm, at frequency 0.8 Hz with averaged unit load: 5, 10, and 15 N for 15 min. The samples were subjected to microscopic observations using scanning electron microscope and a laser scanning microscope. Samples with Ti(C, N) coatings revealed higher fretting wear resistance. The wear in each case with Ti(C, N) coatings was over twice as low. The lowest wear and thus... [more]

Evaporative cooling can be integrated into fresh-air-handling units, to reduce cooling demand. This study considers a hybrid fresh-air-handling unit which incorporates a vapor-compression cooling cycle and indirect evaporative cooling to condition an ambient primary airstream to a desired supply air state. The cooling effects of using various modes (vapor compression only; direct expansion with mist; direct expansion with water shower; and direct expansion with mist and water shower) are compared when the fresh-air-handling unit operates in harsh (hot and humid) climatic conditions experienced in Qatar. Experimental analysis is based on actual ambient conditions measured from August 2018 to July 2019. It is found that the best-performing wet mode of operation saves more than 60% of the energy required by a conventional direct expansion cooling system operating under the same ambient conditions. In hot, dry conditions, the coefficient of performance of the fresh-air-handling unit when u... [more]

Triangular silver nanoplates were prepared by using the seeding growth approach with the presence of citrate-stabilized silver seeds and a mixture of gelatin−chitosan as the protecting agent. By understanding the critical role of reaction components, the synthesis process was improved to prepare the triangular nanoplates with high yield and efficiency. Different morphologies of silver nanostructures, such as triangular nanoplates, hexagonal nanoprisms, or nanodisks, can be obtained by changing experimental parameters, including precursor AgNO3 volume, gelatin−chitosan concentration ratios, and the pH conditions. The edge lengths of triangular silver nanoplates were successfully controlled, primarily through the addition of silver nitrate under appropriate condition. As-prepared triangular silver nanoplates were characterized by transmission electron microscopy (TEM), dynamic light scattering (DLS), UV-Vis, Fourier transform infrared spectroscopy (FT-IR), and X-Ray diffraction (XRD). Si... [more]

Psoriasis is an inflammatory skin disease characterized by the presence of whitish and scaly plaques, which can cover up to 90% of the body surface. These plaques result from the hyperproliferation and abnormal differentiation of keratinocytes. Dermopharmaceutical testing of new therapies is limited by healthy and pathological skin models, which are not closely enough mimicking their in vivo counterparts. In this study, we exploited percutaneous absorption and Ultra Performance Liquid Chromatography (UPLC) analyses in order to determine the metabolic capacity of our psoriatic skin model. Skin substitutes were reconstructed according to the self-assembly method and tested regarding their percutaneous absorption of a topical formulation of tazarotene, followed by UPLC analyses. Histological and immunofluorescence analyses confirmed both the healthy and psoriatic phenotypes. Results from percutaneous absorption showed a significant level of tazarotene metabolite (tazarotenic acid) when th... [more]

With exposure to real-time market pricing structures, consumers would be incentivized to invest in electrical energy storage systems and smart predictive automation of their home energy systems. Smart home automation through optimizing HVAC (heating, ventilation, and air conditioning) temperature set points, along with distributed energy storage, could be utilized in the process of optimizing the operation of the electric grid. Using electricity prices as decision variables to leverage electrical energy storage and flexible loads can be a valuable tool to optimize the performance of the power grid and reduce electricity costs both on the supply and demand sides. Energy demand prediction is important for proper allocation and utilization of the available resources. Manipulating energy prices to leverage storage and flexible loads through these demand prediction models is a novel idea that needs to be studied. In this paper, different models for proactive prediction of the energy demand... [more]

Proteomics and phosphoproteomics have been emerging as new dimensions of omics. Phosphorylation has a profound impact on the biological functions and applications of proteins. It influences everything from intrinsic activity and extrinsic executions to cellular localization. This post-translational modification has been subjected to detailed study and has been an object of analytical curiosity with the advent of faster instrumentation. The major strength of phosphoproteomic research lies in the fact that it gives an overall picture of the workforce of the cell. Phosphoproteomics gives deeper insights into understanding the mechanism behind development and progression of a disease. This review for the first time consolidates the list of existing bioinformatics tools developed for phosphoproteomics. The gap between development of bioinformatics tools and their implementation in clinical research is highlighted. The challenge facing progress is ideally believed to be the interdisciplinary... [more]

The effect of CuO as a sintering additive on the electrolyte of solid oxide electrolysis cells (SOECs) was investigated. 0.5 wt% CuO was added into Sc0.1Ce0.05Gd0.05Zr0.89O2 (SCGZ) electrolyte as a sintering additive. An electrolyte-supported cell (Pt/SCGZ/Pt) was fabricated. Phase formation, relative density, and electrical conductivity were investigated. The cells were sintered at 1373 K to 1673 K for 4 h. The CuO significantly affected the sinterability of SCGZ. The SCGZ with 0.5 wt% CuO achieved 95% relative density at 1573 K while the SCGZ without CuO could not be densified even at 1673 K. Phase transformation and impurity after CuO addition were not detected from XRD patterns. Electrochemical performance was evaluated at the operating temperature from 873 K to 1173 K under steam to hydrogen ratio at 70:30. Adding 0.5 wt% CuO insignificantly affected the electrochemical performance of the cell. Activation energy of conduction (Ea) was 72.34 kJ mol−1 and 74.93 kJ mol−1 for SCGZ and... [more]

The physical and chemical processes in the raceway zone of the COREX melter−gasifier express are similar to those inside the blast furnace. Based on the research achievements on blast furnaces, the unsteady numerical simulation of a gas-solid two-phase in the raceway was carried out by using computational fluid software. The formation process of the raceway in the COREX melter−gasifier was simulated. The shape and size of the raceway were obtained. Then, the effect of gas flow on the depth and height of the raceway was analyzed in this paper.

The traditional treatment of waste incineration flue gas is mostly carried out in low temperatures, but there are some problems such as corrosion of the heating surface at high and low temperatures, re-synthesis of dioxins, and low efficiency. Therefore, it is necessary to remove the pollutants at high temperatures. For the grate waste incinerator, this study proposes an adiabatic cyclone flue arranged at the exit of the first-stage furnace of the grate waste incinerator to pre-remove the fly ash at high temperatures, so as to alleviate the abrasion and corrosion of the tail heating surface. In this paper, computational fluid dynamics (CFD) method is applied to study the performance of a cyclone flue under different structural parameters, and the comprehensive performance of the cyclone flue is evaluated by the technique for order preference by similarity to an ideal solution (TOPSIS) method. The results show that particle separation efficiency increases at first and then decreases wit... [more]

In this study we explored the implementation of the vapor induced phase separation (VIPS) to produce cellulose acetate microcapsules for the encapsulation of a complex mix of fragrances. VIPS is a technique used for membrane preparation, but barely mentioned for microencapsulation. We compared the products from VIPS and a more common microencapsulation process, the immersion precipitation technique (IPS). The capsules prepared via VIPS show a core-shell structure with a thin polymeric shell surrounding the internally empty space, conversely to those produced via IPS, showing an incomplete spherical morphology. This can be attributed to a better control of the precipitation rate of the encapsulation material in the non-solvent thanks to the longer exposition time to the vapor. The activity and encapsulation efficiency of the capsules, obtained through TGA analysis, reached a maximum of ≈75% and ≈90%, respectively. Moreover, a growing trend between the initial active concentration and th... [more]

A high loading production in the manufacturing process of wheat germ (WG) drying is important for reducing the production costs. From a cost perspective, the drying performance become more effective in a batch process when the loading increases. The objective of this investigation was to evaluate the drying performance of WG with different loadings, from 2 to 9 kg, at 120 °C in a fluidized bed dryer. The moisture content, according to the American Association of Cereal Chemists (AACC) method, and the water activity using a thermal hygrometer were measured. The absolute humidity, diffusivity of moisture, and thermal efficiency were analyzed using a mathematical model. An analysis of the dehydration flux demonstrated a linear relationship between dehydration time and WG loading using a fluidized bed dryer. The kinetics of WG drying were observed with a simple exponential model used to match the experimental observation, indicating that the drying rate constant decreases with an increase... [more]

Unreinforced masonry walls are extensively used in the petrochemical industry and they are one of the most vulnerable components to blast loads. To investigate the failure modes and improve the blast resistances of masonry walls, four full-scale field tests were conducted using unreinforced and spray-on polyurea-reinforced masonry walls subjected to gas explosions. The results suggested that the primary damage of the unreinforced masonry wall was flexural deformation and the wall collapsed at the latter stage of gas explosion. The presence of polyurea coatings could effectively improve the anti-explosion abilities of masonry walls, prevent wall collapses, and retain the flying fragments, which would reduce the casualties and economic losses caused by petrochemical explosion accidents. The bond between the polymer and masonry wall was critical, and premature debonding resulted in a failure of the coating to exert the maximum energy absorption effect. A numerical model for masonry walls... [more]