In this study walnut shells, an inexpensive and readily available waste, were used as carbonaceous precursor for preparation of an innovative adsorbent (walnut-shell powder (WSP)) which was successfully tested for the removal of FeII from synthetic acid mine drainage (AMD). Then, the exhausted iron-contaminated adsorbent (WSP-FeII) was recovered and treated with sodium borohydride for the reduction of adsorbed FeII to Fe0. The resulting material (WSP-Fe0) was subsequently tested for the removal of CrVI from aqueous solutions. Treatability batch experiments were employed for both FeII and CrVI-contaminated solutions, and the influence of some important experimental parameters was studied. In addition, the experimental data was interpreted by applying three kinetic models and the mechanism of heavy metal removal was discussed. The overall data presented in this study indicated that fresh WSP and WSP-Fe0 can be considered as promising materials for the removal of FeII and CrVI, respective... [more]

Sulfur-impregnated zeolite has been obtained from the natural zeolite clinoptilolite by chemical modification with Na2S at 150 °C. The purpose of zeolite impregnation was to enhance the sorption of Hg(II) from aqueous solutions. Chemical analysis, acid and basic properties determined by Bohem’s method, chemical behavior at different pHo values, zeta potential, cation-exchange capacity (CEC), specific surface area, X-ray powder diffraction (XRPD), scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), as well as thermogravimetry with derivative thermogravimetry (TG-DTG) were used for detailed comparative mineralogical and physico-chemical characterization of natural and sulfur-impregnated zeolites. Results revealed that the surface of the natural zeolite was successfully impregnated with sulfur species in the form of FeS and CaS. Chemical modification caused an increase in basicity and the net negative surface charge... [more]

Friction occurs in the processes of transport and storage of granular plant materials used in the energy (RES—Renewable Energy Sources) and food sectors. This paper presents the results of a study on the impact of the moisture content of the material and the number of its contact points with a smooth surface (a steel sheet) on the process of friction in grains of wheat and buckwheat. The friction process was studied for four different levels of moisture (9.5%, 13.5%, 17.5% and 21.5%) and three different average numbers of contact points. To measure the force of friction, an universal testing machine with appropriate instrumentation was used. To determine the number of contact points, computer imaging analysis was conducted. An increase in static and kinetic friction was observed along with the increase in moisture level and the increase in the number of contact points. Correlation and regression analysis was performed for the data obtained.

In this paper, performance analysis over two years’ operation of an industrial anaerobic digestion (AD) plant of a separately collected organic fraction of municipal solid waste is presented. The continuous plug-flow AD plant is still regularly operating and it has been fully operational since September 2018. Since then, it has been supplied with 40,000 t/y of pretreated separately collected organic fraction of municipal solid waste from municipalities of the Calabria region in Southern Italy. The AD process is carried out in a mesophilic regime at 40 ± 0.5 °C, using a constant hydraulic retention time (HRT) of 22 days and a substrate with average total solids and average total volatile solids of 30.0% and 22.2%, respectively. In the last two years, the plant produced an average of 191 m3 and 860 m3 of biogas per tonne (t) of organic input material and of total volatile solids, respectively, with an average methane specific production of 508 m3/t (total volatile solids). The average CH... [more]

A liposome-based artificial cell (LBAC) consists of a liposome encapsulating a cell-free protein expression system (CFPES) and protein-encoding DNA. It is surrounded by a lipid bilayer membrane and synthesizes proteins that resemble actual cells. Hence, they have been one of the most studied artificial cells. According to recent studies, they have been able to sense bio-functional molecules by synthesizing fluorescent proteins in response to target molecules. Therefore, they are expected to be used as biosensors. However, previously reported LBACs encapsulated the CFPES derived from Escherichia coli, resulting in the most productive protein expression at 20−40 °C. To broaden the range of their working temperatures to lower temperatures, in this study, we constructed LBACs using a CFPES derived from Pseudomonas fluorescens that grows at a temperature range of 4 °C to 30 °C. We then demonstrated that the constructed LBAC expressed proteins at 8 °C and that, the protein expression capabil... [more]

Reliable production of freshwater and energy is vital for tackling two of the most critical issues the world is facing today: climate change and sustainable development. In this light, a comprehensive review is performed on the foremost renewable energy-driven polygeneration systems for freshwater production using thermal and membrane desalination. Thus, this review is designed to outline the latest developments on integrated polygeneration and desalination systems based on multi-stage flash (MSF), multi-effect distillation (MED), humidification-dehumidification (HDH), and reverse osmosis (RO) technologies. Special attention is paid to innovative approaches for modelling, design, simulation, and optimization to improve energy, exergy, and thermo-economic performance of decentralized polygeneration plants accounting for electricity, space heating and cooling, domestic hot water, and freshwater production, among others. Different integrated renewable energy-driven polygeneration and desa... [more]

Biotrickling filters are one of the most widely used biological technologies to perform biogas desulfurization. Their industrial application has been hampered due to the difficulty to achieve a robust and reliable operation of this bioreactor. Specifically, biotrickling filters process performance is affected mostly by fluctuations in the hydrogen sulfide (H2S) loading rate due to changes in the gas inlet concentration or in the volumetric gas flowrate. The process can be controlled by means of the regulation of the air flowrate (AFR) to control the oxygen (O2) gas outlet concentration ([O2]out) and the trickling liquid velocity (TLV) to control the H2S gas outlet concentration ([H2S]out). In this work, efforts were placed towards the understanding and development of control strategies in biological H2S removal in a biotrickling filter under aerobic conditions. Classical proportional and proportional-integral feedback controllers were applied in a model of an aerobic biotrickling filte... [more]

The issues of feedstocks, product markets, and environmental emissions have continuously proposed a number of challenges for industrial evaluation of fresh fluid catalytic cracking (FCC) catalyst before its application in commercial units. In this work, a convenient method was proposed by comparing with the existing commercial equilibrium catalyst. A series of laboratory experiments for steam treatments and microactivity tests were established to collect reliable data, and the standalone catalyst or co-catalysts were assessed to show the evaluation process and the predicted unit performance. The results had deviation, but a consistent yield distribution than that of a commercial equilibrium catalyst. These evaluations and predictions would provide us with not only the view of hydrothermal stability and yield distribution at the unit level, but also the economic potential for fresh catalyst based on the existing industrial catalyst, which will provide refiners with industrial basis for... [more]

The coal to ethylene glycol (CTEG) process has drawn much attention due to the serious conflict between supply and demand of ethylene glycol in China. However, it is inevitably accompanied by the problem of high CO2 emissions. Carbon capture is one of the most promising potential effective ways to address this issue. However, the CTEG process, integrated with carbon capture technology, will lead to energy and economic penalties. Thus, a comprehensive evaluation of CTEG process with different CO2 capture technologies is urgently needed. This study analyzed the technoeconomic performance of four CO2 capture alternatives for the CTEG process: Rectisol, mono-ethanol amine (MEA), chilled ammonia process (CAP) and dimethyl carbonate (DMC) technologies. Results show the energy consumption of CO2 capture of the Rectisol process is the lowest, 1.88 GJ/tCO2, followed by the DMC process, 2.10 GJ/tCO2, the CAP process, 3.64 GJ/tCO2, and the MEA process, 5.20 GJ/tCO2. The CO2 capture cost of the Re... [more]

The production of so-called advanced bioethanol offers several advantages compared to traditional bioethanol production processes in terms of sustainability criteria. This includes, for instance, the use of nonfood crops or residual biomass as raw material and a higher potential for reducing greenhouse gas emissions. The present review focuses on the recent progress related to the production of advanced bioethanol, (i) highlighting current results from using novel biomass sources such as the organic fraction of municipal solid waste and certain industrial residues (e.g., residues from the paper, food, and beverage industries); (ii) describing new developments in pretreatment technologies for the fractionation and conversion of lignocellulosic biomass, such as the bioextrusion process or the use of novel ionic liquids; (iii) listing the use of new enzyme catalysts and microbial strains during saccharification and fermentation processes. Furthermore, the most promising biorefinery approa... [more]

The photo-catalytic degradation of a textile azo-dye as Methyl Orange was studied in an innovative unit constituted by a channel over which a layer of titanium dioxide (TiO2) catalyst in anatase form was deposited and activated by UVB irradiation. The degradation kinetics were followed after variation of the chemical, physical, and hydraulic/hydrodynamic parameters of the system. For this purpose, the influence of the TiO2 dosage (g/cm3), dye concentration (mg/L), pH of the solution, flow-rate (L/s), hydraulic load (cm), and irradiation power (W) were evaluated on the degradation rates. It was observed that the maximum dosage of TiO2 was 0.79 g/cm3 while for higher dosage a reduction of homogeneity of the cement conglomerate occurred. The Langmuir−Hinshelwood (LH) kinetic model was followed up to a dye concentration around 1 mg/L. It was observed that with the increase of the flow rate, an increase of the degradation kinetics was obtained, while the further increase of the flow-rate as... [more]

The purpose of this work is to increase the theoretical and methodological approaches to value and regulate the dynamics of management processes. Application of these dynamics is implemented via methods of improving the quality of management of complex energy technology systems in the organization of recycling processes. As a result of the research, a technological model of a rotary kiln with a division into separate sections corresponding to the combustion zones for the production of cement clinker in recycling technology was developed. Mathematical modeling, analytical calculations of thermodynamic and gas-dynamic processes in the drums of rotating furnaces, and experimental studies were carried out. As a scientific novelty, an approximation of piecewise linear functions is obtained for modeling the processes of improving the quality of control by the criterion of reducing the error of data transmission for monitoring and regulating the thermodynamic parameters of the furnace via ana... [more]

Animal production inevitably causes the emission of greenhouse gases and the generation of large amounts of slurry, both representing a serious environmental problem. Photosynthetic microorganisms such as microalgae and cyanobacteria have been proposed as alternative strategies to bioremediate agricultural waste while consuming carbon dioxide and producing valuable biomass. The current study assessed the potential of the microalga Scenedesmus sp. to remove nutrients from piggery wastewater (PWW) and the influence of the microalga on the microbial consortia. Maximum N-NH4+ consumption was 55.3 ± 3.7 mg·L−1·day−1 while P-PO43− removal rates were in the range 0.1−1.9 mg·L−1·day−1. N-NH4+ removal was partially caused by the action of nitrifying bacteria, which led to the production of N-NO3−. N-NO3− production values where lower when microalgae were more active. This work demonstrated that the photosynthetic activity of microalgae allows us to increase nutrient removal rates from PWW and t... [more]

This study aimed to determine the effects of osmotic dehydration on the kinetics of hot air drying of apricot halves under conditions that were similar to the industrial ones. The osmotic process was performed in a sucrose solution at 40 and 60 °C and concentrations of 50% and 65%. As expected increased temperatures and concentrations of the solution resulted in increased water loss, solid gain and shrinkage. The kinetics of osmotic dehydration were well described by the Peleg model. The effective diffusivity of water 5.50−7.387 × 10−9 m2/s and solute 8.315 × 10−10−1.113 × 10−9 m2/s was calculated for osmotic dehydration. Hot air drying was carried out at 40, 50, and 60 °C with air flow velocities of 1.0 m/s and 1.5 m/s. The drying time shortened with higher temperature and air velocity. The calculated effective diffusion of water was from 3.002 × 10−10 m2/s to 1.970 × 10−9 m2/s. The activation energy was sensitive to selected air temperatures, so greater air velocity resulted in great... [more]

The equilibrium and kinetics of CO2 adsorption at 273 K by coconut-shell activated carbon impregnated with sodium hydroxide (NaOH) was investigated. Based on nitrogen adsorption isotherms, porous properties of the tested activated carbons decreased with the increase of NaOH loading, with the decrease resulting primarily from the reduction of pore space available for nitrogen adsorption. Equilibrium isotherms of CO2 adsorption by activated carbons impregnated with NaOH at 273 K and the pressure up to 100 kPa displayed an initial part of Type I isotherm with most adsorption taking place in micropores in the range of 0.7−0.9 nm by pore-filling mechanisms. The amount of CO2 adsorbed increased with the increase of NaOH loading and passed through a maximum at the optimum NaOH loading of 180 mg/g. The CO2 isotherm data were best fitted with the three-parameter Sips equation, followed by Freundlich and Langmuir equations. The pore diffusion model, characterized by the effective pore diffusivit... [more]

In this article, chaotic search based constrained equilibrium optimizer algorithm (CS-CEOA) is suggested by integrating a novel heuristic approach called equilibrium optimizer with a chaos theory-based local search algorithm for solving general non-linear programming. CS-CEOA is consists of two phases, the first one (phase I) aims to detect an approximate solution, avoiding being stuck in local minima. In phase II, the chaos-based search algorithm improves local search performance to obtain the best optimal solution. For every infeasible solution, repair function is implemented in a way such that, a new feasible solution is created on the line segment defined by a feasible reference point and the infeasible solution itself. Due to the fast globally converging of evolutionary algorithms and the chaotic search’s exhaustive search, CS-CEOA could locate the true optimal solution by applying an exhaustive local search for a limited area defined from Phase I. The efficiency of CS-CEOA is stu... [more]

The process instability of anaerobic digestion (AD) is a common issue and may result in underperformance or short-term process failure. Extensive research has shown that total solids (TS) content in AD has a significant impact on system stability and performance. However, no study has examined the feasibility of stabilizing the AD process by maintaining constant TS content in the digestate. In this study, an innovative control approach based on constant TS content in the digestate during AD was developed using a mass balance equation. Two levels of TS content (desired values of 4% wet basis (w.b.) and 6% w.b.) were compared with conventional control. The process stability was examined by monitoring digestate components and pH. Substrate-specific methane yield (m3 CH4/kg VS) was used to assess the effectiveness of the controlled conditions. The results showed that the digestate TS content during AD can be controlled and that the digestion process can be stabilized by controlled conditio... [more]

Energy plays an essential role in the modern society and can serve as one of the vital parameters of socio-economic development. Despite developments in technology, over three billion persons living in rural parts of the low- and middle-income countries continue to cover their energy needs for cooking through traditional ways by burning biomass resources. This paper as a case study focuses on the Aral Sea region of Uzbekistan, possessing a well-developed agricultural production with high livestock numbers and intensive crop production. The manure of the livestock farms is not used efficiently and the energy supply of the farms depends primarily on centrally produced gas and electricity. Some areas are not yet connected to the gas grid. Agriculture causes huge environmental damages in its current form. The benefit of biogas production would therefore be fivefold: (1) local energy source, (2) mitigation of environmental impacts, (3) reducing CH4-emissions, (4) producing organic fertilize... [more]

A large eddy simulation (LES) was performed for film cooling in the gas turbine blade involving spanwise injection angles (orientation angles). For a streamwise coolant injection angle (inclination angle) of 35°, the effects of the orientation angle were compared considering a simple angle of 0° and 30°. Two ratios of the coolant to main flow mass flux (blowing ratio) of 0.5 and 1.0 were considered and the experimental conditions of Jung and Lee (2000) were adopted for the geometry and flow conditions. Moreover, a Reynolds averaged Navier−Stokes simulation (RANS) was performed to understand the characteristics of the turbulence models compared to those in the LES and experiments. In the RANS, three turbulence models were compared, namely, the realizable k-ε, k-ω shear stress transport, and Reynolds stress models. The temperature field and flow fields predicted through the RANS were similar to those obtained through the experiment and LES. Nevertheless, at a simple angle, the point at w... [more]

The purpose of this work was to investigate the detection of the pesticide residual (profenofos) in tomatoes by using visible/near-infrared spectroscopy. Therefore, the experiments were performed on 180 tomato samples with different percentages of profenofos pesticide (higher and lower values than the maximum residual limit (MRL)) as compared to the control (no pesticide). VIS/near infrared (NIR) spectral data from pesticide solution and non-pesticide tomato samples (used as control treatment) impregnated with different concentrations of pesticide in the range of 400 to 1050 nm were recorded by a spectrometer. For classification of tomatoes with pesticide content at lower and higher levels of MRL as healthy and unhealthy samples, we used different spectral pre-processing methods with partial least squares discriminant analysis (PLS-DA) models. The Smoothing Moving Average pre-processing method with the standard error of cross validation (SECV) = 4.2767 was selected as the best model fo... [more]

The thermal decomposition of wood chips from an apple tree is studied in a static air atmosphere under isothermal conditions. Based on the thermogravimetric analysis, the values of the apparent activation energy and pre-exponential factor are 34 ± 3 kJ mol−1 and 391 ± 2 min−1, respectively. These results have also shown that this process can be described by the rate of the first-order chemical reaction. This reaction model is valid only for a temperature range of 250−290 °C, mainly due to the lignin decomposition. The obtained results are used for kinetic prediction, which is compared with the measurement. The results show that the reaction is slower at higher values of degree of conversion, which is caused by the influence of the experimental condition. Nevertheless, the obtained kinetic parameters could be used for the optimization of the combustion process of wood chips in small-scale biomass boilers.

Charcoal is an interesting reducing agent because it is produced from biomass which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. Biocarbon is a promising alternative to fossil reductants for reducing greenhouse gas emissions and increasing sustainability of the metallurgical industry. In comparison to conventional reductants (i.e., petroleum coke, coal and metallurgical coke), charcoal has a low density, low mechanical properties and high CO2 reactivity, which are undesirable in ferroalloy production. Densification is an efficient way to upgrade biocarbon and improve its undesirable properties. In this study, the deposition of carbon from methane on three types of charcoal has been investigated at 1100 °C. CO2 reactivity, porosity and density of untreated and densified charcoal were measured, and results were compared to metallurgical coke. Surface morphology of the charcoal samples was inves... [more]

The dry washing method is an alternative to replace water washing, thereby reducing the negative impacts of contamination. However, commercial adsorbents come from industrial processes that, due to their composition, may not be such a sustainable resource in the global biodiesel production process. In this study, the use of organic residues, such as sawdust, coconut fiber, nutshell, rice husk, and water hyacinth fiber, were proposed as bioadsorbents for the purification of biodiesel from waste cooking oil. Quality parameters such as the acid number, water content, and free and total glycerin content were evaluated and compared with those after purification with commercial adsorbents (Magnesol and Amberlite BD10DRY). Promising results were obtained using sawdust in the purification process, achieving a reduction in the acid number value of 31.3% respect to the unpurified biodiesel. Indeed, the reduction with sawdust was more efficient than with Amberlite BD10DRY (that increased the acid... [more]

Investigating the transient behaviour of liquid CO2 decompression is of great importance to ensure the safety of pipeline transportation in carbon capture and storage (CCS) technology. A computational fluid dynamics (CFD) decompression model based on the non-equilibrium phase transition and Span−Wagner equation of state (EoS) was developed to study the effects of actual flowing state within the pipeline on the transient behaviour of liquid CO2 decompression. Then, the CFD model was verified by comparing the simulated results to test data of a large-scale “shock tube” with an inner diameter of 146.36 mm. The results showed that the evaporation coefficient had a significant impact on the transition behaviour of CO2 decompression, while the condensation coefficient made no difference. When the evaporation coefficient was 15 s−1, the CFD-predicted results were in good agreement with the test results. Moreover, the effects of flow velocity on transient behaviour of liquid CO2 decompression... [more]

In the present study, the flow of a fibre suspension in a channel containing a cylinder was numerically studied for a very low Reynolds number. Further, the model was validated against previous studies by observing the flexible fibres in the shear flow. The model was employed to simulate the rigid, semi-flexible, and fully flexible fibre particle in the flow past a single cylinder. Two different fibre lengths with various flexibilities were applied in the simulations, while the initial orientation angle to the flow direction was changed between 45° ≤ θ ≤ 75°. It was shown that the influence of the fibre orientation was more significant for the larger orientation angle. The results highlighted the influence of several factors affecting the fibre particle in the flow past the cylinder.