The Paris Agreement requires a drastic reduction of global carbon emissions towards the net zero transition by mid-century, based on the large-scale transformation of the global energy system and major emitting sectors. Aviation and shipping emissions are not on a trajectory consistent with Paris goals, driven by rapid activity growth and the lack of commercial mitigation options, given the challenges for electrification of these sectors. Large-scale models used for mitigation analysis commonly do not capture the specificities and emission reduction options of international shipping and aviation, while bottom-up sectoral models do not represent their interlinkages with the entire system. Here, I use the global energy system model PROMETHEUS, enhanced with a detailed representation of the shipping and aviation sector, to explore transformation pathways for these sectors and their emission, activity, and energy mix impacts. The most promising alternative towards decarbonizing these secto... [more]

The bidirectional dc-dc converter is a critical component for extending the use of renewable energy and improving the efficiency of high-power electronic systems. This paper presents the analysis of the stray inductance of a commutation loop and the commutation behavior of IGBT devices in a flying capacitor three-level bidirectional DC-DC converter (FC-3L-BDC) phase-leg power electronic building block (PEBB). An FC-3L-BDC phase-leg PEBB was designed as an example, which can be used to build 400 kW to MW-grade light rail train chargers, battery energy storage interface converters, or metro regenerative braking energy recovery converters with a single PEBB or several PEBBs interleaved parallel. In order to optimize the stray inductance of commutation paths and realize snubberless operation, a five-layer laminated bus bar was carefully designed, and the stray inductance of the bus bar was extracted by three-dimensional finite element analysis simulation. To obtain higher accuracy, the str... [more]

The dynamic performance of the DC bus significantly influences the impedance characteristics of MMC and the system stability in a high-voltage direct current system. However, most of the existing MMC-HVDC system stability research simplifies the DC side as an ideal voltage source and ignores the impacts of voltage feedforward control, which affects the accuracy and practicability of stability analysis. In this paper, a sequence impedance model considering both DC voltage control and voltage feedforward control is developed, and the necessity of considering DC control and voltage feedforward control for MMC-HVDC stability analysis is illustrated. Then, the impact of control parameters on MMC-HVDC impedance is discussed, and the boundary conditions of control parameters are also derived. Finally, a method of control parameters design and impedance optimization for MMC-HVDC based on the stability boundary is proposed. Compared to the traditional optimization method, the system stability i... [more]

Nuclear power plants have a complex structure and changeable operation mode, which induces low setting calculation efficiency. After analyzing the technology, architecture, and functional logic of a variety of relay protection setting calculation systems and combining the characteristics of the setting calculation of nuclear power plants, the relay protection setting calculation system in nuclear power plants based on B/S architecture and cloud computing is studied in this paper. The system adopts three-tier B/S architecture, applies two key technologies, the cloud computing task distribution synchronization mechanism and the cloud component automatic assembly mechanism, and introduces a particle swarm optimization algorithm to provide technical support for nuclear power plant setting calculation; the running example of the nuclear power plant system fully proves the efficiency and reliability of the relay protection setting calculation system of the nuclear power plant, which has high... [more]

The key goal of this research was to figure out the short and long run relationship between environmental degradation caused by carbon dioxide (CO2) emissions and energy consumption, the level of GDP economic growth, and urbanization in the Visegrad Region countries (V4). The study used data from the years 1996−2020. In the methodological area, ARDL bound test, and ARDL and ECM models were used to determine the directions and strength of interdependence. The results show that in the case of some V4 countries (Poland, Slovakia, and Hungary), changes in the urbanization rate affect CO2 emissions. Moreover, it was confirmed that the phenomenon of urbanization influences the enhanced energy consumption in the studied countries. In the case of individual countries, these relationships were varied, both unidirectional and bidirectional. Their nature was also varied—there were both long and short-term relationships. These findings suggest that the V4 countries should increase renewable and ec... [more]

Transient electromagnetic (TEM) surveys constitute an important element in exploration projects and can be successfully used in the search for oil and gas. Different modifications of the method include shallow (sTEM), 2D, 3D, and 4D (time-lapse) soundings. TEM data allow for solving a large scope of problems for estimating resources and reserves of hydrocarbons, discriminating reservoir rocks, detecting tectonic features, and characterizing drilling conditions. TEM surveys are applicable at all stages, from initial prospecting to production, and are especially efficient when combined with seismic surveys. Each stage has its specific objectives: estimation of net pay thickness, porosity, and fluid type during prospecting, optimization of well placement and prediction of drilling conditions in exploration, and monitoring of flooding during production. Electromagnetic soundings resolve permafrost features well and thus have a high potentiality for exploration in the Arctic petroleum provi... [more]

Energy deposition for flow and flight control has received significant interest in the past several decades due to its potential application to high-speed flow and flight control. This paper reviews recent progress and recommends future research.

In this paper, the transient state analysis of a Line-Start Permanent Magnet Synchronous Motor (LSPMSM) and the optimum design for high efficiency were studied. In the case of an LSPMSM, aluminum bars and permanent magnets are inserted in the rotor. Since it has aluminum bars, it can be directly started on-line without closed-loop control at the time of starting, like an induction motor. Furthermore, once driven, it rotates at a synchronous speed due to the permanent magnets in the steady state. Theoretically, since the rotor bars have no induced current, copper loss does not occur in the rotor bars. Further, because of the inserted permanent magnets, an LSPMSM has a higher power density than an induction motor with the same output power. However, since it is driven directly on-line, the transient state is longer than that of a synchronous motor driven by an inverter. Therefore, it is important to analyze the characteristics of the transient state depending on the rotor shape in the LS... [more]

An important feature of this research is the investigation of the de-alloyed catalysts based on the nanoparticles with a simple structure (alloy) and a complex structure (gradient). The resulting samples exhibit the 2−4 times higher mass activity in the ORR compared with the commercial Pt/C. The novelty of this study is due to the application of the express-electrochemical experiment to register the trend of changes in the ORR activity caused by rearranging the structure of bimetallic nanoparticles. The state-of-the-art protocol makes it possible to establish the dependence of properties of the de-alloyed catalysts on the nanoparticles’ structure obtained at the stage of the material’s synthesis. The study shows the possibility of determining the rate of the ongoing reorganization of bimetallic nanoparticles with different architectures. The PtCu/C electrocatalysts for proton-exchange membrane fuel cells presented in this work are commercially promising in terms of both the high functi... [more]

In this paper, an integrated system based on low-concentrated photovoltaic/thermal (LCPV/T) technology and efficient vacuum membrane distillation (VMD) seawater desalination utilizing the energy of solar is established. Through a theoretical analysis and a series of experiments, this paper explores the temperature change of a single VMD process, and the variation trend of single-day membrane flux with solar irradiation and temperature parameters. In addition, the changes in solar irradiation, temperatures of the integrated system, membrane flux, and thermoelectric properties in different seasons are also analyzed. A mathematical model was established to calculate the relationship between membrane flux and temperature difference. The experimental results show that the membrane flux of VMD is 2.73 L/(m2·h); the simulated seawater can achieve a desalination rate of 99.9%. After economic analysis, the operating incomes of the system under sunny weather conditions in different seasons were... [more]

The existing motor fault classification methods mostly use sensors to detect a single fault feature, which makes it difficult to ensure high diagnostic accuracy. In this paper, a motor fault classification method based on multi-source information fusion Naive Bayes classification algorithm is proposed. Firstly, this paper introduces the concept and advantages of multi-source information fusion, as well as its problems of miscellaneous information and inconsistent data magnitude. For example, as this paper classifies the fault of generators, there are many physical quantities, such as voltage, current and temperature, which are not in the same dimension, therefore it is difficult to fuse. Then, aiming at the corresponding problems, this paper uses a PCA dimension reduction method to remove redundant information and reduce the dimension of multi-dimensional complex information. Aiming at the problem of unequal data magnitude, the interval mapping method is adopted to effectively solve th... [more]

Determining the geomechanical properties of hydrate-bearing sands (HBS), such as strength and stiffness, are critical for evaluating the potential for the economic and safe recovery of methane gas from HBS reservoirs. To date, results from numerous independent laboratory studies on synthesized HBS have shown that strength and stiffness are largely influenced by hydrate saturation, the method adopted for hydrate formation, and to a lesser extent, the confining stresses applied during testing. However, a significant scatter is observed in the data even when these conditions are similar. These include recent studies on natural HBS where sands with larger particle size distribution (PSD) exhibited higher strengths despite lower hydrate saturation. To investigate the impact of PSD, and the role that specific hydrate formation conditions might impose, on the strength and stiffness of HBS, a series of laboratory tests were carried out on sand specimens formed with different particle size dist... [more]

A cooling tower is an important guarantee for the proper operation of a solar system. To ensure proper operation of the system and to maintain high-efficiency points, the cooling tower must operate year-round. However, freezing is a common problem that degrades the performance of cooling towers in winter. For example, the air inlet forms hanging ice, which clogs the air path, and the coil in closed cooling towers freezes and cracks, leading to water leakage in the internal circulation. This has become an intractable problem that affects the safety and performance of cooling systems in winter. To address this problem, three methods of freeze protection for cooling towers are studied: (a) the dry and wet mixing operation method—the method of selecting heat exchangers under dry operation at different environments and inlet water temperatures is presented. The numerical experiment shows that the dry and wet mixing operation method can effectively avoid ice hanging on the air inlet. (b) The... [more]

The integration of renewable resources with distribution networks (DNs) is an effective way to reduce carbon emissions in energy systems. In this paper, an economic and low-carbon-oriented optimal planning solution for the integration of photovoltaic generation (PV) and an energy storage system (ESS) in DNs is proposed. A convolutional neural network (CNN)-based prediction model is adopted to characterize the uncertainties of PV and load demand in advance. Then, taking the lowest total economic cost, the largest carbon emission reduction, and the highest system power supply reliability as the optimization objectives, the optimal distribution network planning model is constructed. The improved multi-objective particle swarm optimization (MOPSO) algorithm is used to solve the optimization model, and the effectiveness of the proposed solution is confirmed through a comparative case study on the IEEE-33 bus system. Simulation results show that the proposed solution can better maintain the... [more]

Nuclear technologies have strong potential and a unique role to play in delivering reliable low carbon energy to enable a net-zero society for future generations. However, to assure the sustainability required for its long-term success, nuclear will need to deliver innovative solutions as proposed in iMAGINE. One of the most attractive features, but also a key challenge for the envisaged highly integrated nuclear energy system iMAGINE, is the need for a demand driven salt clean-up system based on the principles of reverse reprocessing. The work described provides an insight into the dynamic interplay between a potential salt clean-up system and reactor operation in a plutonium-started core in a dynamic approach. The results presented will help to optimise the parameters for the salt clean-up process as well as to understand the differences which appear between a core started with enriched uranium and plutonium as the fissile material. The integrated model is used to investigate the eff... [more]

In order to objectively reflect the energy utilization performance of an active water heating system (AWHS) using photovoltaic/thermal (PV/T) modules, this study proposes a new evaluation method based on energy efficiency, exergy efficiency and thermal-electrical output of a system in year-round weather conditions. Four samples of PV/T modules were surveyed to compare and evaluate the effectiveness of the system, called MD1, MD2, MD3 and MD4, respectively. The simulation program was developed to suit four types of PV/T modules and MATLAB was used as the programming language. The water flow through the four PV/T module samples and the hot water tank volume were investigated for the highest exergy efficiency of the system. The final results illustrate that in the weather conditions of Ho Chi Minh City, Vietnam, the system has the highest energy efficiency, exergy efficiency and thermal output when using MD1 with 57.85%, 15.67% and 2.93 kWh/m2/day, respectively, while the system has highe... [more]

With the rapid development of pumped storage, the vibration problems caused by the operation of power stations have become increasingly prominent. In this paper, a large-scale pumped-storage power station is taken as the research object, and a three-dimensional refined finite element model of the underground powerhouse including the surrounding rock mass is established. Based on the analysis of the vibration source of the powerhouse and the water diversion pipeline, the modal and dynamic response analysis of the underground powerhouse of the hydropower station is carried out, and the distribution law of the larger vibration displacement position is revealed. The calculation results show that under the premise that the vibration source is selected reasonably and the numerical model is accurate, the main frequency of the underground powerhouse structure can be obtained more accurately. After optimizing the design of the underground powerhouse based on the calculation results, the resonan... [more]

Liquid wastes are generated during production in the milk and cheese industries. During cheese production, whey emerges as a liquid product. Researchers define waste as raw material instead of waste alone. Hence, there is no doubt that the use and management of waste will gain greater importance in the upcoming years. This study discusses the use of whey, which is food waste, in agriculture and the benefits derived from it in terms of energy value. Our research was based on the current literature and the amount of whey that emerged in the dairy industry. For this purpose, the existing literature was evaluated to determine how much waste was produced from whey. The total amount of whey waste in Turkey for 2021 was determined. Afterwards, the amount of potential energy was determined in evaluating these wastes. Turkey’s total amount of potential energy obtained from whey waste was calculated as 570.11 × 106 MJ, with 158.36 × 106 kWh as potential electrical energy. Moreover, it was calcul... [more]

This paper proposes a new peer-to-peer (P2P) energy trading method between energy sellers and consumers in a community based on multi-agent reinforcement learning (MARL). Each user of the community is treated as a smart agent who can choose the amount and the price of the electric energy to sell/buy. There are two aspects we need to examine: the profits for the individual user and the utility for the community. For a single user, we consider that they want to realise both a comfortable living environment to enhance happiness and satisfaction by adjusting usage loads and certain economic benefits by selling the surplus electric energy. Taking the whole community into account, we care about the balance between energy sellers and consumers so that the surplus electric energy can be locally absorbed and consumed within the community. To this end, MARL is applied to solve the problem, where the decision making of each user in the community not only focuses on their own interests but also ta... [more]

Marine renewable sources can make a significant contribution to the development of electrical energy generation and can increase the power supply reliability of mineral complexes. The development of alternative energy sources is happening at a fast pace, and this is due to the improvement of technologies that allow for generating more energy and operating in more extreme conditions, with almost no negative effect on the environment. However, currently, renewable sources are not able to meet all the energy requirements of the platforms. Hence, a key point is to gradually introduce and develop new technologies. This article explores the advantages of combining power generation by wave converters and offshore wind turbines. It investigates the possibilities of improving the combined systems’ reliabilities through justification of their mutual topology and accounting for the shadow effect from the wave installations.

This paper presents the application of multi-criteria decision-making (MCDM) for evaluating what technologies using renewable energy sources (RES) for electricity production have the chance to develop in Poland under the current socio-economic conditions. First, the Analytical Hierarchy Process (AHP) method was used to determine the weights of the optimization criteria. Five main criteria and 30 sub-criteria were identified. Next, the authors modified numerical taxonomy (NT) to rank eight RES technologies (such as onshore and offshore wind farms, photovoltaics, or biogas plants). The results show that offshore wind farms are the RES technology with the greatest development opportunities in Poland. The following three technologies: distributed photovoltaic energy, biogas plants, and biomass power plants, respectively, received a similar rating in the ranking. Hydropower and geothermal were the lowest-ranked technologies. The ranking, which is the result of multi-criteria analysis, in se... [more]

Today, one of the main priorities in Europe is to introduce measures to increase environmental protection. Therefore, SMEs operating in the branch related to renewable energy are essential for several EU priorities. SMEs can also be vulnerable, especially during times of crisis, which could negatively affect renewable energy development. Therefore, this paper aims to evaluate and analyze the financial security management of renewable energy SMEs during the COVID-19 pandemic. The research is conducted on SMEs operating in the renewable energy sector in Poland. The research periods are 2019 (before the COVID-19 crisis) and 2020 (during the crisis). By analyzing different financial performance ratios, we found that SMEs operating in the energy sector have been able to stabilize and maintain their current economic position compared to the past. The results of this study indicate that the receivables collection period, cash conversion cycle, and operating cycle could have been insignificant... [more]

The main challenges of the input current control in synchronous DC-DC buck converters are the nonlinear model of the system, changes of the operating point in a wide range, and the need to use an input LC filter for current smoothing, which may result in the instability of the closed-loop system. In this paper, a step-by-step approach is developed for the design and improvement of a PI-feedforward closed-loop controller. It is shown that a linear PI controller cannot stabilize the closed-loop system properly during wide changes in model parameters, e.g., an equivalent series resistance of the input filter. To cope with the stability issues, a fixed-frequency sliding mode controller (SMC) has been developed in this paper for the implementation of an electro-mechanical actuator (EMA) emulator. Moreover, a systematic approach is proposed for controller tuning and the selection of the SMC’s gains. To achieve high power efficiency, high-frequency GaN switches are used for the practical impl... [more]

The transition to a climate-neutral economy presents a particular challenge for the areas where the economy is based on rich lignite resources. One of them is the Bełchatów Basin Area in Poland. The complexity of the phenomena occurring in the area of transformation requires an interdisciplinary and integrated approach to development planning and managing. It is important to create stable conditions, allowing for the introduction of necessary changes, including the involvement of various stakeholders. The research is aimed at identifying the challenges faced by the region with a lignite-based economy, the inhibitors of the transformation process, and recommendations for public policy. During the research, secondary and primary data were analysed with the use of triangulation, which allowed to combine various techniques and sources, as well as an in-depth description and multi-faceted understanding of the case under study. The study poses a key question as to whether the public authorit... [more]

Magnetorheological (MR) dampers are controlled energy-dissipating devices utilizing smart fluids. They operate in a fast and valveless manner by taking advantage of the rheological properties of MR fluids. The magnitude of the response of MR fluids, when subjected to magnetic fields, is of sufficient magnitude to employ them in various applications, namely, vibration damping, energy absorption, exoskeletons, etc. At the same time, predicting their response to arbitrary mechanical and electrical inputs is still a research challenge. Due to the non-linearities involved in material properties or the design of the solenoid used for activating the fluid modeling the relationships between the control circuit and the material’s response is complex. Modeling studies can be classified into two categories. The parametric approach requires the knowledge of the internal material’s properties and takes advantage of physics formulas to infer the I/O relationships present in the damper. For compariso... [more]