Atomic Force Microscopy (AFM) nanoindentation is a powerful technique for determining the mechanical properties of soft samples at the nanoscale. The Hertz model is typically used for data processing when employing spherical indenters for small indentation depths (h) compared to the radius of the tip (R). When dealing with larger indentation depths, Sneddon’s equations can be used instead. In such cases, the fitting procedure becomes more intricate. Nevertheless, as the h/R ratio increases, the force−indentation curves tend to become linear. In this paper the potential of using the linear segment of the curve (for h > R) to determine Young’s modulus is explored. Force−indentation data from mouse and human lung tissues were utilized, and Young’s modulus was calculated using both conventional and linear approximation methods. The linear approximation proved to be accurate in all cases. Gaussian functions were applied to the results obtained from both classic Sneddon’s equations and the s... [more]

Using slow-release fertilizer is one of the sustainable strategies to improve the effectiveness of fertilizers and mitigate the environmental pollution caused by excess usage of fertilizer. In this study, a slow-release urea fertilizer with water retention and photosensitivity properties was prepared by a two-step method. It was characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy and an infrared camera. This fertilizer can prolong the release period of urea, improve water-retention capacity of soil, and carry out photothermal conversion under illumination. Comparing four release kinetics models, the Ritger−Peppas model was the best fitting model for releasing behavior in soil, and diffusion followed the Fickian mechanism. The application of fertilizer on winter wheat was carried out to intuitively evaluate the fertilizer’s effects on promoting plant growth and resisting water stress. Thus, this study provides a new strategy... [more]

To characterize the failure of rock mass surrounding underground tunnels, biaxial compression tests were conducted on a real sandstone model with a straight-walled arched hole. The acoustic emission (AE) system and digital image correlation (DIC) optical inspection equipment were used to investigate the crack evolution process and failure precursors of the tunnel. A two-dimensional particle flow code (PFC2D) was used to conduct numerical simulations on the sample, so as to investigate the mesoscopic failure mechanism of rock mass. The results show that the failure of the single tunnel constructed in sandstone occurs mainly in the walls on both sides (between the spandrels and arch feet), showing slabbing failure characteristics and a certain abruptness. The crack initiation in sandstone in early stage is not obvious, and the crack propagation in rock mass is rapid when acoustic emissions are enhanced. The small increments in the AE count and amplitude and the continuous reduction in th... [more]

As the proportion of renewable energy installations in modern power systems increases, major weather events can easily trigger significant fluctuations in new energy generation and electricity load, presenting the system with the dual challenges of ensuring power supply and renewable energy consumption. Traditional dispatch models need more coordination and optimization of flexible resources under major weather events and risk management of system operations. This study focuses on provincial-level transmission systems, aiming to achieve the coordinated and optimized dispatch of flexible resources across multiple time scales in response to the complex and variable environments faced by the system. Firstly, by profoundly analyzing the response mechanisms of power systems during major weather events, this study innovatively proposes an event-driven day-ahead and intra-day optimal dispatch strategy for power systems. This strategy can sense and respond to major weather events in the day-ah... [more]

It is of great significance to investigate the flow rate and stress distribution of multi-fracture propagation for the optimization of perforation parameters and fracture parameters. Considering the coupling of rock deformation, fracture direction and fluid flow in multi-fracture scenarios, a mathematical model and solution program for the flow and stress distribution of multiple fractures are established, and the analytical model is used for comparison and verification. The effects of perforation cluster number, cluster spacing, perforation diameter on fracture extension trajectory, fracture width, flow rate of each fracture and stress field are studied by the model. The results show that, as the number of perforating clusters increases, the inner fracture is inhibited more severely with less width, length and flow distribution, as well as lower bottom hole pressure. With the increase in cluster spacing, the stress interference between whole fractures is weakened and the flow distribu... [more]

Pump-turbines experience complex flow phenomena and fluid−structure interactions during transient operations, which can significantly impact their stability and performance. This paper presents a comprehensive field test study of the pump mode startup process for a 150 MW prototype pump-turbine. By analyzing pressure fluctuations, structural vibrations, and their short-time Fourier transform (STFT) results, multiple stages were identified, each exhibiting distinct characteristics. These characteristics were influenced by factors such as runner rotation, free surface sloshing in the draft tube, and rotor−stator interactions. The natural frequencies of the metallic components varied during the speed-up and water-filling stages, potentially due to gyroscopic effects or stress-stiffening phenomena. The opening of the guide vanes and dewatering valve inside the guide vanes significantly altered the amplitude of the rotor−stator interaction frequency, transitioning the vibration behavior fro... [more]

The primary function of a mine hoist is the transportation of personnel and equipment, serving as a crucial link between underground and surface systems. The proper functioning of key components such as work braking and safety braking is essential for ensuring the safety of both personnel and equipment, thereby playing a critical role in the safe operation of coal mines. As coal mining operations extend to greater depths, they introduce heightened challenges for safe transportation, compounded by increased equipment loss. Consequently, there is a pressing need to enhance safety protocols to safeguard personnel and materials. Traditional maintenance and repair methods, characterized by routine equipment inspections and scheduled downtime, often fall short in addressing emerging issues promptly, leading to production delays and heightened risks for maintenance personnel. This underscores the necessity of adopting predictive maintenance strategies, leveraging digital twin models to antici... [more]

The Pressure Swing Adsorption (PSA) technique is a widely embraced automated method for gas separation within the industrial sector, prized for its operational simplicity and substantial economic benefits. In practice, the process typically involves the use of multiple towers to facilitate the completion of the PSA cycle. However, with the increasing number of towers in a PSA system, the intricacies of the cyclic process tend to amplify, posing challenges for novices attempting to grasp the mechanics of a six-tower PSA cycle. Utilizing animation can facilitate the process of comprehending these complex techniques by presenting them in a simplified and visually engaging format. Therefore, our research group has designed an animated depiction of a six-tower PSA device, predicated on the prototype established in our laboratory. This animation furnishes an inclusive demonstration of a complete cycle, encompassing twelve steps, pertaining to the operation of a six-tower PSA. It is our aspir... [more]

In order to reduce the failure accidents caused by the insufficient strength of fracturing string joints, theoretical calculation and string design methods were adopted to conduct finite element calculations on commonly used long circular threads. The distribution laws of stress and contact pressure of long round threads were obtained, a non-standard special thread was designed, and a finite element model of the joint of the casing was established. Considering different make-up torques, tensile loads, and tensile torque loads within a certain range, the stress variation law of the special casing threaded joint under this design size was analyzed. Finally, the stress and contact pressure variation law on the threaded tooth was analyzed under different structures, working conditions, and wall thickness parameters. The thread strength and sealing function were compared under various parameters. The results showed that the smaller the wall thickness of the joints, the greater the contact p... [more]

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, research was active in finding out alternative systems, mostly relying on aqueous liquids that are low-cost and ecofriendly. After the emergence of carbon nanotubes (CNTs), with their many special structural, electrical and thermal properties, they have been examined for many applications, including heat-transfer processes. Adding CNTs to water yields CNT aqueous nanofluids that have been widely investigated as heat-transfer media. The literature shows that CNT addition improves water thermal conductivity and other water properties, such as viscosity, surface tension, freezing point and boiling point. The literature also shows that nanofluid thermal conductivity improvement is affected by CNT type and concentration, in addition to other factors such as surfactant addition. All these subjects were widely described i... [more]

Waste biogenic materials derived from seafood exploitation represent valuable resources of new compounds within the blue bioeconomy concept. Here, we describe the effectiveness of Raman technology implementation as an in-line tool for the demineralization process control of crustaceans or gastropods. Transparent chitin polymeric foils and calcium acetate by-products were obtained from three waste crustacean shells (C. sapidus, S. mantis, and M. squinado) using a slow, green chemical approach employing acetic acid. Progressive mineral dissolution and increasing of the Raman characteristic signal of chitin is shown in a time-dependent manner using NIR-Raman spectroscopy, while resonance Raman shows intact carotenoids in reacted shells after 2 weeks. Chitin foil products are species-specific, and the demineralization bath of the waste shell mixture can be effectively tracked by Raman tools for solvent control and decision making for the recovery of calcium acetate by-products. Comparative... [more]

Phytoremediation, an ecological approach aimed at addressing polymetal(loid)lic-contaminated mining soils, has encountered adaptability challenges. Dominant plant species, well-suited to the local conditions, have emerged as promising candidates for this purpose. This study focused on assessing the phytoremediation potential of ten plant species that thrived in heavy metal(loid)-contaminated mining soils. This investigation covered nine heavy metal(loid)s (As, Cu, Cd, Cr, Hg, Ni, Pb, Sn, and Zn) in both plants and rhizosphere soils. The results revealed a significant impact of mining activities, with heavy metal(loid) concentrations surpassing the Yunnan Province’s background levels by 1.06 to 362 times, highlighting a significant concern for remediation. The average levels of the heavy metal(loid)s followed the order of As (3.98 × 103 mg kg−1) > Cu (2.83 × 103 mg kg−1) > Zn (815 mg kg−1) > Sn (176 mg kg−1) > Pb (169 mg kg−1) > Cr (68.1 mg kg−1) > Ni (36.2 mg kg−1) > Cd (0.120 mg kg−1)... [more]

Autostrainer is used for the purpose of debris removal in order to increase the efficiency of the heat exchanger by taking the required raw water as a heat source for the pre-cooling hydrothermal system. During the operation of the autostrainer, a pressure drop occurs due to the blockage of the screen in the autostrainer. As a result, the resistance of the pipe network for the intake system is changed, and the operating efficiency point of the pump, valve, heat exchanger, etc., is altered. By calculating the system resistance taking into account the pressure drop caused by the blockage rate of the screen in the autostrainer, the optimum operating efficiency can be expected when the intake system such as a pump, valve or heat exchanger, etc. is constructed. In this study, Computational Fluid Dynamics (CFD) was used to construct a scenario in which screen blockage may occur, predicting pressure drop for the slot cross-section of the screen in the autostrainer to derive a resistance coeff... [more]

Hot air-assisted radio frequency (HARF) is considered a rapid heating process. In order to improve the circular economy of agricultural byproducts, this study used different proportions of HARF stabilized rice bran (R) from milling rice, HARF dried ginseng residue (G) from ultrasonic extraction, and peanut residue (P) from HARF roasting and oil extraction as the Hericium erinaceus solid-state fermented media. Then, the whitening effects of water extracts from media and fermented products were analyzed. First, the surface temperature of 1 kg rice bran exceeded 90 °C after 3 min of 5 kW HARF heating, effectively deactivating lipase. The combinations of 1 kg of rice bran with 0.5, 1, 1.5, and 2 kg of ginseng residue (85% moisture content) were dried using 5 kW HARF. Each of the drying rates was about 27 g/min, and the drying periods were 14, 30, 46, and 62 min, respectively, which were used to reduce the moisture content below 10%. Compared to traditional air drying for ginseng residue, H... [more]

“Aging” is a practice that allows alcoholic beverages to mature and gives them particular flavors and colors. In this context, oak or durmast wooden barrels are used in this process, thus providing different types of aging. This conventional process produces a slow enrichment of organic compounds in the spirit inside the barrels. Organic substances present in the internal part of the barrels slowly undergo the phenomenon of extraction by the liquid phase (solid−liquid extraction). In this work, a new procedure based on rapid solid−liquid dynamic extraction (RSLDE) was used to evaluate the potential of obtaining the effects of aging in spirits in shorter times than conventional methods. For this purpose, a comparison between two solid−liquid extraction techniques, RSLDE and conventional maceration, was made. Four water/ethanol 60:40 (v/v) model solutions were prepared and put in contact with medium-toasted chips using the two extraction procedures (conventional and non-conventional) and... [more]

The seepage effect of rock and soil in the process of encountering water follows a nonlinear coupling law between water and rock. According to the permeability of rock and soil during softening with water, changes in particles in rock and soil are related to permeability mechanisms. Based on the assumption of connection between particles in rock and soil, changes in particles before and after water infiltration, the mechanism of water−rock interaction, and the damage to rock and soil are analyzed herein. Combined with fractal theory and percolation theory, the random failure characteristics and nonlinear behavior of water in rock and soil are studied. At the same time, with the help of Fluent 17.0 software, the seepage process of rock samples in water is numerically simulated and analyzed. Taking the permeability coefficient of rock samples, the mass flow rate of water, and the internal pore water pressure of rock samples as tracking objects, it is found that there are obvious nonlinea... [more]

This study evaluated the changes in microbial activity in the course of time following the joint application of the herbicides S-metolachlor, foramsulfuron, and thiencarbazone-methyl to two soils (S1 and S2) under conventional tillage (CT) and non-tillage (NT) management in field conditions. The biochemical parameters of soil respiration (RES), dehydrogenase activity (DHA), microbial biomass (BIO), and the phospholipid fatty acid (PLFA) profile were determined at 1, 34, and 153 days during herbicide dissipation. In the absence of herbicides, all microbial activity was higher under NT than CT conditions, with higher or similar mean values for S1 compared to S2. A continuous decrease was detected for RES, while DHA and BIO recovered over time. In the presence of herbicides, a greater decrease in all microbial activity was detected, although the changes followed a similar trend to the one recorded without herbicides. In general, a greater decrease was observed in S1 than in S2, possibly d... [more]

The dynamic model of cavitation bubbles serves as the foundation for the study of all cavitation phenomena. Solving the cavitation bubble dynamics equation can better elucidate the physical principles of bubble dynamics, assisting with the design of hydraulic machinery and fluid control. This paper employs a fourth-order explicit Runge−Kutta numerical method to solve the translational Keller−Miksis model for cavitation bubbles. It analyzes the collapse time, velocity, as well as the motion and force characteristics of bubbles under different wall distances γ values. The results indicate that as the distance between the cavitation bubble and the wall decreases, the cavitation bubble collapse time increases, the displacement of the center of mass and the amplitude of translational velocity of the cavitation bubble increase, and the minimum radius of the cavitation bubble gradually decreases linearly. During the stage when the cavitation bubble collapses to its minimum radius, the Bjerkne... [more]

The complexity and heterogeneity of pore structures in carbonate reservoirs pose significant challenges for accurately characterizing the influence of different pore micro-parameters on reservoir physical properties. Drawing upon the principles of fractal geometry theory applied to reservoir rocks, this study combines mercury intrusion porosimetry (MIP) and nuclear magnetic resonance (NMR) T2 spectrum methods to explore the relationship between the fractal dimension and micro-parameters of pore throats at various scales. Additionally, it clarifies how the fractal dimension of pores at different scales impacts reservoir physical properties. Moreover, a permeability prediction model that incorporates fractal dimensions is developed. The findings demonstrate that the fractal dimension effectively captures the complexity and multi-scale nature of reservoir microstructures, leading to higher reliability in predicting permeability when using the model incorporating the fractal dimension. It... [more]

With the introduction of numerous technologies and equipment, the volume of data in smart substations has undergone exponential growth. In order to enhance the intelligent management level of substations and promote their efficient and sustainable development, the one-key sequential control system of smart substations is being renovated. In this study, firstly, the intelligent substation is defined and compared with the traditional substation. The one-key sequential control system is introduced, and the main issues existing in the system are analyzed. Secondly, experiments are conducted on the winding temperature, insulation oil temperature, and ambient temperature of power transformers in the primary equipment. Combining data fusion technology and transformer neural network models, a Power Transformer-Transformer Neural Network (PT-TNNet) model based on data fusion is proposed. Subsequently, comparative experiments are conducted with multiple algorithms to validate the high accuracy,... [more]

In the case of strong non-Gaussian noise in the measurement information of the distribution network, the strong non-Gaussian noise significantly interferes with the filtering accuracy of the state estimation model based on deep learning. To address this issue, this paper proposes an enhanced kernel ridge regression state estimation method based on ensemble empirical mode decomposition. Initially, ensemble empirical mode decomposition is employed to eliminate most of the noise data in the measurement information, ensuring the reliability of the data for subsequent filtering. Subsequently, the enhanced kernel ridge regression state estimation model is constructed to establish the mapping relationship between the measured data and the estimation residuals. By inputting the measured data, both estimation results and estimation residuals can be obtained. Finally, numerical simulations conducted on the standard IEEE-33 node system and a 78-node system in a specific city demonstrate that the... [more]

Fractured-vuggy reservoirs are crucial for increasing unconventional oil storage and production, but the controlling mechanism of this dominant flow channel remains vague, and the jamming mechanism of modulator particles is unclear. This study explores the filling and jamming processes of particles in the fractures by conducting a computational fluid dynamics−discrete element method (CFD−DEM) coupled simulation, considering the variation of fracture width, fluid velocity, particle size, and concentration. Results suggest that four sealing modes are proposed: normal filling, local jamming, complete sealing, and sealing in the main fracture. The ratio of particle size to the main fracture width exerts the primary role, with the ratio having a range of 0.625 < D/W ≤ 0.77 revealing complete jamming. Furthermore, an optimal particle size for achieving stable sealing is observed when the particle size varies from 2 to 2.5 mm. A higher concentration of particles yields better results in th... [more]

The paper shows the expediency of supplementing the balance simplex method by calculating the number of free variables of separation flowsheets containing recycle flows. The need to determine and set the free variables that provide lower energy consumption when calculating the material balance of flowsheets with recycling is justified. The problem of material balance multivariance is illustrated, and ways to solve it are shown with the example of separation flowsheets for two ternary mixtures: n-butanol + water + toluene and n-butanol + butyl acetate + water. Separation flowsheets containing three distillation columns and a liquid−liquid separator are proposed for both systems. The dependence of the recycle flow values and the energy consumption of distillation columns and separation flowsheets on the selection and setting of values of free variables in solving the balance problem is shown. The dependence of energy consumption on the composition of the original mixture is studied for a... [more]

The research on the deep coalbed methane (CBM) in the Ordos Basin is mostly concentrated on the eastern margin of the basin. The geological resources of the Benxi Formation in the Yulin area, located in the central-eastern part, cover 15,000 × 108 m3, indicating enormous resource potential. However, the characteristics of the reservoir distribution and the favorable areas are not yet clear. This research comprehensively performed data logging, coal rock experiments, and core observations to identify the geological characteristics of the #8 coal seam, using a multi-level fuzzy mathematics method to evaluate the favorable area. The results indicate the following: (1) The thickness of the #8 coal in the Yulin Block ranges from 2.20 m to 11.37 m, with depths of between 2285.72 m and 3282.98 m, and it is mainly underlain by mudstone; the gas content ranges from 9.74 m3/t to 23.38 m3/t, showing a northwest−low and southeast−high trend. The overall area contains low-permeability reservoirs, w... [more]

Traditional batch ethanol fermentation poses the problems of poor production and economic viability because the lag and stationary phase always demand considerable fermentation time; plus, downtime between batches is requested to harvest, clean, and sterilize, decreasing the overall productivity and increasing labor cost. To promote productivity and prolong the production period, avoid process instability, and assure a substantial production of ethanol and a minimal quantity of residual substrate, this paper proposed a nonlinear adaptive control which can realize global stabilizing control of the process starting from batch mode to achieve batch/washout avoidance. Due to the dynamic nature and complexity of the process, novel estimation and control schemes are designed and tested on an ethanol fermentation model. These schemes are global stabilizing control laws including adaptive control to avoid input saturation, nonlinear estimation of the unknown influential concentration through a... [more]